FCC ID: PY3AC785S WWAN Mobile Hotspot Portable Device

Notification of Compliance Regulatory Compliance Information This document includes user requirements for operating NETGEAR products in accordance with national laws including usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable national regulatory authority. The NETGEAR product firmware limits operation to only the channels allowed in a particular region or country. Therefore, all options described in this document may not be available in your version of the product. This document applies to both Class A and Class B devices:

Class A devices are intended to be used in a commercial or industrial environment. They are not intended to be used in a residential home or be available for general public use. Class B devices are intended to be used in a residential setting, and may also be used in commercial and industrial applications. Examples of Class B devices are telephones, personal computers, and residential data gateways. Fuses should only be installed by service personnel. NETGEAR recommends the use of 26 AWG or larger gauge phone line cords. Europe EU Declaration of Conformity This section applies to products bearing the CE or CE! mark:

Products bearing the CE or CE! mark comply with the following EU directives:

EMC Directive 2004/108/EC Low Voltage Directive 2006/95/EC Ecodesign Directive 2009/125/EC RoHS Directive 2011/65/EU If the product has telecommunications functionality, it also complies with the requirement of the following EU directive:

R&TTE Directive 1999/5/EC Compliance with these directives implies conformity to harmonized European standards that are noted in the EU Declaration of Conformity. The EU CE Declaration of Conformity may be found at http://support.netgear.com/app/answers/detail/a_id/11621/. Caution for installing this equipment outdoors: (Valid in all EU member states, EFTA states, and Switzerland.) Be aware that outdoor installations require special attention and will only be handled by trained and qualified installation personnel. No one from the general public is permitted to install NETGEAR wireless products outdoors when external antennas, power and grounding must be installed for use. Particular attention has to be given allowed operational frequencies. Contact NETGEAR for instructions on how to contact an installer for outdoor operations if this product requires the special considerations for outdoor installations. For detailed information concerning installations in France, the user should contact the national spectrum authority in France (http://www.arcep.fr/ ) The following paragraphs apply to WN2500RP:

This device is a 2.4GHz and 5GHz wideband transmission system (transceiver), intended for indoor use only in all EU member states, EFTA states, and Switzerland. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for applying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10mW EIRP in the frequency range of 2454-2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. The following paragraph applies to the LG2210:

External antenna requirement: Net gain (antenna + cable) of external antenna is required to be less than 1.14dBi

(minimum gain of internal antenna). Warning NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference in which case the user may be required to take adequate measures. FCC Requirements for Operation in the United States Information in this section applies to products bearing the FCC mark (or statement):

FCC Information to User This NETGEAR product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals. WNR2010 WNR2020 WNR614 WNR618 The following statement applies to these products:

C6300 C7000BMX D6000 D6010 D3600 D3610 D6200V2 EX2700 EX6100 EX6200 FS205v2 FS208v2 FS305v2 FS308v2 FS605v4 FS608v4 GS205v2 GS208v2 GS305 GS308v2 GS605v5 GS608v4 HMNC100 R6050 R6200v3 R6220 R7500 R8000 JNR1010v2 JR6150 JWNR2000v5 JWNR2010v5 STS7000 VEGN2200 VMB3000 VMC3010 VMC3030 WN370 WN1000v4 WN2500RP WN3000RPv2 WN3500RP WNA1000Mv2 WNDA3100v3 WNDR3400v3 WNDR3700v5 WNDR4300v2 WNDR4500v3 This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. FCC Guidelines for Human Exposure The NETGEAR product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. The following statement applies to this product:

C6300BD This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device should be installed and operated with minimum distance of 35cm between the radiator and your body. The following statement applies to this product:

C6300XB3 This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device should be installed and operated with minimum distance of 25cm between the radiator and your body. The following statement applies to this product:

R8000 This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device should be installed and operated with minimum distance of 30cm between the radiator and your body. FCC Declaration of Conformity We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that this product complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:

The device may not cause harmful interference, and The device must accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Warnings & Instructions The NETGEAR product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:

Reorient or relocate the receiving antenna. Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is Increase the separation between the equipment and the receiver. connected. Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure and SAR Statements The information in this section applies to products that transmit data or communicate wirelessly. SAR Statement The information in this section applies to NETGEAR wireless products that are intended to be operated close to human body. NETGEAR products that are intended to be operated close to the human body are tested for body-worn Specific Absorption Rate (SAR) compliance. The SAR limit set by the FCC is 1.6 W/kg. The FCC has established detailed SAR requirements and NETGEAR products meet these requirements. NETGEAR products comply with ANSI/IEEE C95.1-1999 and are tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C. NETGEAR products that are installed in USB ports demonstrate SAR compliance using a typical laptop computer with a USB port. Other applications, such as handheld computers or similar devices, have not been verified and might not compliance with related RF exposure rule and such use is prohibited. RF Exposure Information NETGEAR products have been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the requirements as set forth in CFR 47 Sections, 2.1093, and 15.247 (b) (4) addressing RF exposure from radio frequency devices. NETGEAR products meet the applicable government requirements for exposure to radio frequency waves. To see the test results reporting the highest SAR level measured for this device, visit http://www.netgear.com/about/regulatory/declarations-conformity/

Radiation exposure: NETGEAR products comply with radiation exposure limits set forth for an uncontrolled environment and meet radio frequency (RF) exposure guidelines for wireless routers. NETGEAR products should be installed and operated keeping the product 20cm or more away from a persons body. For devices that are battery powered and may be operated closer than 20cm to you, refer to the NETGEAR website for exposure levels. NETGEAR USB dongle transmitters are approved for use in typical laptop computers. To comply with FCC RF exposure requirements, do not use NETGEAR USB dongle transmitters in other devices or certain laptop and tablet computer configurations where the USB connectors on the host computer are unable to provide or ensure the necessary operating configurations intended for the device and its users or bystanders to satisfy RF exposure compliance requirements. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. NETGEAR products comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) NETGEAR products may not cause harmful interference, and (2) NETGEAR products must accept any interference received, including interference that may cause undesired operation. For products available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible. The following statement applies to these products:

C6300 C7000BMX D6000 D6010 D3600 D3610 D6200V2 EX2700 EX6100 JNR1010v2 JR6150 JWNR2000v5 JWNR2010v5 R6050 R6200v3 R6220 R7500 R8000 VMC3010 VMC3030 WAC120 WN370 WN2500RP WN3000RPv2 WN3000RPv3 WN3500RP WNA1000Mv2 WNDR3700v5 WNDR4300v2 WNDR4500v3 WNR1000v4 WNR2010 WNR2020 WNR614 WNR618 EX6200 HMNC100 VEGN2200 VMB3000 WNDA3100v3 WNDR3400v3 The device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. The following statement applies to these products:

A6210 C6300 C6300XB3 C7000BMX D6000 D6010 D3600 D3610 D6200V2 JR6150 EX6100 EX6200 HMNC100 R6050 R6200v3 R6220 R7500 R8000 STS7000 WN2500RP WNDR3400v3 WNDR3700v5 WNDR4300v2 WNDR4500v3 The device operates in 5.15~5.25GHz frequency range. It is restricted in indoor environment only. The following statements apply to this product:

A6210 WAC120 WNDR3400v3 The device operates in 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range. It is restricted in indoor environment only. The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be changed by the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Non-DFS Warning NETGEAR non-DFS products do not support operation in the 5600-5650MHz band. The firmware on the device restricts the operation in this frequency band and does not utilize the channels in this band. NETGEAR non-DFS products will not permit operations on channels 120132 for 11a and 11n/a, which overlap the 56005650MHz band. The following statements apply to these products:

A6210 HMNC100 R7500 R8000 WNDR3400v3 NETGEAR DFS products do not support operation in the 5600-5650MHz band. The firmware on the device restricts the operation in this frequency band and does not utilize the channels in this band. NETGEAR DFS products will not permit operations on channels 120132 for 11a and 11n/a, which overlap the 5600 5650MHz band. Country Code Selection Usage (WLAN devices) The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. TV Tuner (on Selected Models) The information in this section applies to NETGEAR products incorporating a TV tuner. Note to CATV System Installer: This reminder is provided to call the CATV system installers attention to Section 820-

93 of the National Electrical Code, which provides guidelines for proper grounding and, in particular, specifies that the Coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as possible. Canadian Department of Communications Radio Interference Regulations The information in this section applies to products bearing the statements:. This digital apparatus does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. Cet appareil numrique ne dpasse pas les limites de la classe B pour les missions radio bruit des appareils numriques, tel qu'nonc dans le Rglement sur le brouillage radiolectrique du ministre des Communications du Canada. CAN ICES-3 (B)/NMB-3(B) CAN ICES-3 (A)/NMB-3(A) Industry Canada NETGEAR products comply with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) NETGEAR products may not cause harmful interference, and (2) NETGEAR products must accept any interference received, including interference that may cause undesired operation. A6210 C7000BMX D6000 D6010 D3600 D3610 EX2700 HMNC100 JNR1010v2 JR6150 JWNR2000v5 JWNR2010v5 R6050 R6200v3 R6220 R7500 R8000 VMB3000 VMC3010 VMC3030 WAC120 WN3000RPv3 WN370 WNA1000Mv2 WNDA3100v3 WNDR3400v3 WNDR3700v5 WNDR4300v2 WNDR4500v3 WNR1000v4 WNR2010 WNR2020 WNR614 WNR618 Ce dispositif est conforme la norme CNR d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. A6210 C7000BMX D6000 D6010 D3600 D3610 EX2700 HMNC100 JNR1010v2 JR6150 JWNR2000v5 JWNR2010v5 R6050 R6200v3 R6220 R7500 R8000 VMB3000 VMC3010 VMC3030 WAC120 WN3000RPv3 WN370 WNA1000Mv2 WNDA3100v3 WNDR3400v3 WNDR3700v5 WNDR4300v2 WNDR4500v3 WNR1000v4 WNR2010 WNR2020 WNR614 WNR618 The following statements apply to this product:

R7500 VMB3000 WNDA3100v3 Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum

(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpassepas l'intensit ncessaire l'tablissement d'une communication satisfaisante. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. The paragraph below applies to the following NETGEAR products:-

EX6200 EX7000 JNR3210 R7000 R7500 WN203 The above radio transmitters with detachable antennas have been approved by Industry Canada to operate with the antenna types listed below:-

Master Wave Technology 98619PRSX005 Master Wave Technology 98619PRSX006 Master Wave Technology 98241MRSX012 Master Wave Technology 98365PRSX002 Master Wave Technology 98364PRSX004 Master Wave Technology 98365PRSX000 Master Wave Technology 98365PRSX001 Wha Yu Industrial Co Ltd C529-510542-A The following antenna table applies to VMB3000 product:

The following antenna table applies to R7500 product:

IMPORTANT NOTE: Radiation Exposure Statement NETGEAR products comply with IC radiation exposure limits set forth for an uncontrolled environment. NETGEAR products should be installed and operated with minimum distance 20cm between the radiator and your body. The following statement applies to this product:

R8000 This product complies with IC radiation exposure limits set forth for an uncontrolled environment. NETGEAR products should be installed and operated with minimum distance 30cm between the radiator and your body. NETGEAR products comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in its manual. Further RF exposure reduction can be achieved by keeping the product as far as possible from your body or by setting the device to a lower output power if such a function is available. For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. The following statement applies to these products:

C7000BMX D6000 D6010 D3600 D3610 D6200V2 EX2700 EX6100 EX6200 HMNC100 JNR1010v2 JR6150 JWNR2000v5 JWNR2010v5 R6050 R6200v3 R6220 R7500 R8000 STS7000 VEGN2200 VMB3000 VMC3010 VMC3030 WN370 WN2500RP WN3000RPv2 WN3000RPv3 WNA1000Mv2 WNDR3400v3 WNDR3700v5 WNDR4300v2 WNDR4500v3 WNR1000v4 WNR2010 WNR2020 WNR614 WNR618 The device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-transmitter product procedures. The following statement applies to these products:

A6210 AC785S C7000BMX D6000 D6010 D3600 D3610 D6200V2 JR6150 EX6100 EX6200 HMNC100 R6050 R6200v3 R6220 R7500 R8000 STS7000 WAC120 WN2500RP WNDR3400v3 WNDR3700v5 WNDR4300v2 WNDR4500v3 The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-

channel mobile satellite systems. DFS warning:

NETGEAR DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 5470-

5600MHz, and 5650-5725MHz:

The following statements apply to this product:

A6210 C6300BD C6300XB3 C7000BMX HMNC100 R7500 R8000 STS7500 WAC120 WNDR3100v3 WNDR3400v3 WNDR4300v2 WNDR4500v3 The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz to comply with the EIRP (Equivalent Isotropically Radiated Power) limit. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. The following statement applies to this product:

WAC120 WNDA3100v3 The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the EIRP (Equivalent Isotropically Radiated Power) limits specified for point-to-point and non point-to-point operation as appropriate. SAR warning:

NETGEAR product is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528. NOTE IMPORTANTE: Dclaration d'exposition aux radiations Produits NETGEAR sont conformes aux limites IC d'exposition aux rayonnements dfinies pour un environnement non contrl. Produits NETGEAR doivent tre installs et utiliss avec distance minimum de 20cm entre le radiateur et votre corps. La dclaration suivante s'applique ce produit :

R8000 Ce produit est conforme aux limites IC d'exposition aux rayonnements dfinies pour un environnement non contrl. Produits NETGEAR doivent tre installs et utiliss avec un minimum de 30cm entre le radiateur et votre corps. Produits NETGEAR sont conformes la limite d'exposition aux RF portable Canada tablies pour un environnement non contrl et sont sans danger pour le fonctionnement prvu comme dcrit dans le manuel. Poursuite de la rduction de l'exposition aux RF peut tre ralis en gardant le produit autant que possible de votre corps ou par le rglage du dispositif une puissance de sortie infrieure si une telle fonction est disponible Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. La dclaration suivante s'applique ces produits:

C7000BMX D6000 D6010 D3600 D3610 D6200V2 EX2700 EX6100 EX6200 HMNC100 JNR1010v2 JR6150 JWNR2000v5 JWNR2010v5 R6050 R6200v3 R6220 R7500 R8000 STS7000 VEGN2200 VMB3000 VMC3010 VMC3030 WN370 WN2500RP WN3000RPv2 WN3000RPv3 WNA1000Mv2 WNDR3400v3 WNDR3700v5 WNDR4300v2 WNDR4500v3 WNR1000v4 WNR2010 WNDA3100v3 WNR2020 WNR614 WNR618 Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. La dclaration suivante s'applique ces produits:

A6210 C7000BMX D6000 D6010 D3600 D3610 D6200V2 EX6100 JR6150 EX6200 HMNC100 R6050 R6200v3 R6220 R7500 R8000 STS7000 WAC120 WN2500RP WNDR3400v3 WNDR3700v5 WNDR4300v2 WNDR4500v3 les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. DFS avertissement:

Slection dynamique de frquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-

5600 MHz et 5650-5725 MHz :

Les instructions suivantes s'appliquent ce produit:

A6210 C6300BD C6300XB3 C7000BMX HMNC100 R7500 R8000 STS7500 WAC120 WNDR3100v3 WNDR3400v3 WNDR4300v2 WNDR4500v3 le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la limite de p.i.r.e. De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Le gain d'antenne maximum autoris pour les appareils dans la bande 5725-5825 MHz pour se conformer la pire limites fixes pour les oprations se point- -point et non point- -point, le cas chant. La dclaration suivante s'applique ce produit;

WAC120 Avertissement SAR:

NETGEAR est le respect de SAR pour la population gnrale / limites d'exposition incontrle de CNR-102 et a t test en conformit avec les mthodes et procdures de mesure spcifies dans la norme IEEE 1528. Interference Reduction Table The table below shows the Recommended Minimum Distance between NETGEAR equipment and household appliances to reduce interference (in feet and meters). Household Appliance Microwave oven Baby monitor analog Baby monitor digital Cordless phone analog Cordless phone digital Bluetooth device ZigBee Recommended Minimum Distance (in feet and meters) 30 feet / 9 meters 20 feet / 6 meters 40 feet / 12 meters 20 feet / 6 meters 30 feet / 9 meters 20 feet / 6 meters 20 feet / 6 meters Japan Notices VCCI This information in this section applies to products bearing the VCCI mark:

Class A ITE A Class B ITE B Japan Wireless Notice South Korea Notices The information in this section applies to products bearing the KCC mark:

:

Class A :

A

( ) Class B :

B

( )

(A)

, .

(B)

, . Taiwan WWAN Wireless Notice The information in this section applies to products bearing the Taiwan National Communications Commission mark:

This telecom equipment has complied with NCC regulations. 5.25-5.35

()

:

R7500 MPE1mW/cm20.783945 mW/cm2 Thailand Notice The information in this section applies to products approved by the Thailand National Communications Commission:

. China Notices The information in this section applies to products bearing the Chinese Complusory Certification Mark:

This device complies with the requirements in China for Safety and Quality A Australia and New Zealand Notices The information in this section applies to products bearing the Australia C-Tick and A-Tick Compulsory Marks:

This device equipment complies with the Australian and New Zealand regulatory approvals requirements. Warning NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference in which case the user may be required to take adequate measures. LITHIUM ION AND LITHIUM METAL BATTERY PACKAGING LABEL REQUIREMENTS Due to concerns about products shipping with Li-Ion and Li-Metal batteries, the UN developed guidelines regarding the proper testing, packaging, and labeling of these devices. Li-Ion and Li-Metal Batteries Li-Ion batteries are generally rechargeable, while Li-Metal batteries are generally non-rechargeable. Both types of batteries have the potential to create a fire hazard if damaged or improperly packaged. Labeling Requirements for Li-Ion and Li-Metal Batteries The required labels must be present on the pallets and master carton accompanied by a document such as an airway bill or other documents that indicates the following (Lithium Battery Guidance Document 2014):

The package contains lithium ion cells or batteries;

The package must be handled with care and that a flammability hazard exists if the package is damaged Special procedures that should be followed in case the package is damaged Contact information To conform to IATAs Dangerous Good Regulations, different labels apply to different Watt-hour for Li-Ion and different mass for Li-metal. The calculation for Watt-hours is:

Nominal Voltage x Nominal Capacity (Ah) = Watt-hours The volts and ampere can be found in the batteries data sheet. Please see Table below for which proper label to use. Required Labels for Battery Transportation (UN Manual of Tests and Criteria Part III Subsection 38.3) Li-Ion Battery Label Requirements Shipment of Battery Wh (Watt-hour) Labels Limit Battery Weight / Package Contained in Equipment

(installed in the equipment) Equal to or Less than 100Wh Figure 12 or 13 PAX = 5 kg CAO = 5kg Alone Equal to or Less than 100Wh Figure 12 or 13 Equal to or less than 2.7 Wh=2.5 kg OR Greater than 2.7Wh but equal to or less than 100Wh = 2 batteries Packed separately with the Equipment (not installed in the equipment) Equal to or Less than 100Wh Figure 12 or 13 PAX = 5 kg CAO = 5kg Li-Metal Battery Label Requirements Shipment of Battery Mass of Lithium Metal of the battery Labels Limit Battery Weight / Package Contained in Equipment

(installed in the equipment) Equal to or Less than 2g Figure 12 or 13 PAX = 5 kg CAO = 5kg Alone Equal to or Less than 2g Figure 12 or 13 Equal to or less than 0.3g=2.5kg Equal to or Less than 2g Figure 12 or 13 Packed separately with the Equipment (not installed in the equipment) OR Greater than 0.3g but equal to or less than 2g = 2 batteries PAX = 5 kg CAO = 5kg If Li-Ion Battery is more than 100Wh and Li-Metal has a Lithium mass of more than 2g, please consult Environmental Compliance Engineer for proper label to be used. Label content requirement for shipping batteries:

Label content for shipping smaller packages for batteries:

Exemptions for labeling A lithium ion battery handling label is not required when a package contains not more than 2 batteries contained in the equipment. Lithium metal batteries contained in the equipment do not need any lithium battery handling label. Product disposable warning NETGEAR products must not be disposed of together with domestic waste. NETGEAR products must be disposed of at a location that is authorized to recycle electrical and electronic appliances. By collecting and recycling waste, you help save natural resources and make sure that the product is disposed of in an environmentally friendly and healthy way. Tuner Cable and Battery Safety Information Tuner Cable:

This reminder is provided to call the CATV systems installers attention to Section 820-93 of the National Electric Code which provide grounding and , in particular, specify that the Coaxial cable shield shall be connected to the grounding system of the building, so close to the point of cable entry as practical. Battery Caution:

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Powerline Device Safety Information Follow these safety guidelines to ensure your own personal safety and to help protect your system from potential damage:

For national approvals (approval schemes other than CB), relevant national standards for plug, socket-

outlet, and direct plug-in units (for example, US) shall also be consulted while testing and approving such products according to the national standards. Check the electrical current for any device plugged into the filtered AC socket. Do not exceed home and product outlet ratings and electrical requirements. The socket-outlet shall be installed near the equipment and be easily accessible Only power cords and allowed to be inserted into the filtered AC socket; no other equipment with a direct plug-in is allowed. Power cords needs to be a maximum of 1m long and a minimum of 0.75mm of cross-

sectional area. Do not plug devices into the Powerline Pass Thru Adapter filtered AC outlet that exceed the product ratings. The output voltage of the filtered AC outlet is the same as the power outlet that the Powerline Pass Thru Adapter is plugged into. To help avoid damaging your system, be sure that the attached devices are electrically rated to operate with the power available in your location. If the input AC voltage is less than 100 Vac, the device plugged into the filtered AC socket of the Powerline Pass Thru Adapter might not perform as well as expected. DO NOT PLUG MAJOR HOME APPLIANCES into the filtered AC socket or into an attached power strip. The device is not intended to be used with home appliances such as air conditioners, power tools, space heaters, fans hair dryers, ovens, or refrigerators. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Do not service any product except as explained in your system documentation. Opening or removing covers that are marked with the triangular symbol with a lightning bolt can expose you to electrical shock. Only a trained service technician should service components inside these compartments. Use the product only with approved equipment. Allow the products to cool before removing covers or touching internal components. To help avoid damaging your system, be sure that the voltage selection switch (if provided) on the power supply is set o match the power available at your location:

o o o 110 volts (V), 60 hertz (Hz) in most of North and South America and some Far Eastern countries such as south Korea and Taiwan 100, 50 Hz in eastern Japan and 100, 60Hz in western Japan 230v, 50Hz in most of Europe, the Middle East, and the Far East The peripheral power cables are equipped with three-prong plugs to help ensure proper grounding. Do not use adapter plugs or remove the grounding prong from a cable. Observe extension cable and power strip ratings. Make sure that the total ampere rating of all products plugged into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for te extension cable or power strip. To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS). Rack Mount Safety Instructions This information applies to the installation of NETGEAR rack mount products Ambient operating temperature. If the switch is installed in a closed or multiunit rack assembly, the ambient operating temperature of the rack environment might be greater than the ambient temperature of the room. Therefore, consider installing the equipment in an environment compatible with the maximum rated ambient temperature. Reduced airflow. Mount the equipment into a rack so that the amount of airflow required for safe operation is not compromised. Mechanical loading. Mount the equipment into a rack so that a hazardous condition does not arise due to uneven mechanical loading. Circuit overloading. Consider the equipments connection to the power supply circuitry and the effect that any possible overloading of circuits might have on overcurrent protection and power supply wiring. Consider equipment nameplate ratings when addressing this concern. Reliable grounding. This product requires reliable grounding to be maintained at all times. To ensure this, ground the rack itself. Pay particular attention to power supply connections other than the direct connections to the branch circuit (for example, the use of power strips). Clearance. Leave enough clearance in front of the rack (about 25 inches) to enable you to open the front door completely and in the back of the rack (about 30 inches) to allow for sufficient airflow and ease in servicing. NETGEAR, Inc., 350 E. Plumeria Avenue, San Jose, CA 95134 USA January 2015

AirCard 785S Mobile Hotspot Quick Start Meet Your Mobile Hotspot Before you connect your mobile hotspot, familiarize yourself with its LCD screen, icons, buttons, and connectors. Buttons and Connectors Status LED Micro USB port Antenna connector Status LED The status LED indicates data connection status:

Blue, slow blink. Ready. Blue, double blink. Transferring data. Amber, slow blink. The mobile hotspot is not connected to the network. For more information, visit Why cant my mobile hotspot connect to the Internet? on page 13. 2 Navigation button Power button Navigation Button Press the Navigation button to cycle through LCD screens. Power Button Press and hold the Power button for two seconds to power the mobile hotspot on, five seconds to turn the mobile hotspot off. LCD Screen The LCD screen displays icons, data usage, your WiFi name, and your WiFi password. 3 Icon Description 1 bar. The hotspot has a weak signal. 5 bars. The hotspot has a strong signal. Available network technology, varies by service provider coverage. Solid arrows display when the hotspot is transmitting data. You have system alerts requiring attention. You have new SMS messages. The percentage of remaining battery charge. The battery has less than 5% charge. Purple. WiFi is active. Gray. WiFi is inactive. The number indicates the number of devices connected. 4 Set Up Your Mobile Hotspot Before you connect to your mobile hotspot, you must insert a micro-SIM card, install the battery, power up the mobile hotspot, charge your battery, and select a language. Note: To obtain a micro-SIM card, contact your Internet service provider. To insert the micro-SIM card:

1. Remove the back cover using the thumb catch on the corner of the mobile hotspot. 2. 3. Remove the battery. Insert the micro-SIM card. 5 4. 5. 6. Ensure that the micro-SIM card is seated securely. Reinstall the battery. If the battery does not install easily, check the orientation. Replace the cover. To power on your mobile hotspot:

Press and hold the Power button until the LCD screen lights up. A language selection screen displays. To select a language:

1. Press the Navigation button to cycle through the language options until your desired language is highlighted. Press the Power button to select the language. You can change the language again later from the mobile hotspot web page. 2. To recharge your battery:

1. Connect the micro USB cable to your mobile hotspot. 2. Connect the other end of the cable to the USB port on your computer or to the USB charger. Note: Your battery comes partially charged. 6 To connect to your mobile hotspot:

1. Ensure that WiFi is enabled on your computer or other device. 2. On your computer or other device, search for 3. 4. wireless networks:

For Windows devices, click the Internet Access icon. For Mac devices, from the WiFi menu, select the network. For tablets, look for a settings option. Select the WiFi name displayed on your LCD screen. Enter the WiFi password exactly as it appears on the LCD screen. Passwords are case-sensitive. When a computer or mobile device connects to the mobile hotspot, a 1 displays beside the WiFi icon on the LCD screen. Note: For you to connect to the mobile broadband network, your SIM account must be active. If you use a prepaid or pay-as-you-go micro-SIM, the account must have a positive balance. 5. Launch your browser and, if desired, visit http://netgear.aircard to personalize your settings. The mobile hotspot is completely secured using its default security settings. Note: If you see a message indicating you do not have a mobile connection, you may need to add an APN. For information on adding APNs, refer to the user manual. 7 NETGEAR AirCard App Download the complimentary mobile app from www.netgear.com/AirCardApps. Use this app to view your settings and connection and data usage information from your smartphone or tablet. To manage all mobile hotspot settings, visit http://netgear.aircard. Mobile Hotspot Web Page On the mobile hotspot web page, you can do the following:

Change the WiFi SSID, WiFi password, admin password, and WiFi encryption Set autoconnect options View data usage Read SMS messages View Alerts View and change other settings Check device status To access your mobile hotspot web page:

1. Launch an Internet browser from a computer or wireless device that is connected to the network. Enter http://netgear.aircard. 2. 8 3. Enter the administrator login password. The default password is password. The mobile hotspot web page displays. Change Security Settings The WiFi network name and admin password provide security. Your mobile hotspot comes with a randomly generated and secured WiFi network name (SSID) and password that you can continue to use as is. Read this section if you want to change your security settings. To change the WiFi network name:

1. Launch an Internet browser from a computer or wireless device that is connected to the mobile hotspot. Enter http://netgear.aircard. Enter the administrator login password. The default password is password. The mobile hotspot web page displays. Select WiFi > Options. Enter a new WiFi network name. 4. 5. 6. Click the Submit button. To change the WiFi password:

1. Launch an Internet browser from a computer or wireless device that is connected to the mobile hotspot. Enter http://netgear.aircard. The mobile hotspot web page displays. Enter the administrator login password. The default password is password. 2. 3. 2. 3. 9 4. 5. The mobile hotspot web page displays. Select WiFi > Options. The WiFi options screen displays. Enter a new WiFi password. If you change your password, be sure to keep a record of it and store it in a safe place. 6. Click the Submit button. Connect Devices You can add devices to your network using a WiFi network manager or WPS if the device has WPS capability. Note: WPS enables you to connect WPS-enabled devices to a WiFi network without having to input a WiFi password using a keyboard. To connect additional WiFi-capable devices:

1. Open the WiFi network manager on your computer or other WiFi device (smartphones, tablets, media players, cameras, and so on). Select the WiFi network name displayed on the LCD screen. Enter the WiFi password displayed on the LCD screen. Launch your browser. 2. 3. 4. 10 To connect with devices using WPS:

1. Press the Power or Navigation button to awaken the LCD screen. Press the Navigation button until WPS setup screen displays. 2. To activate WPS, press the Power button. 3. 4. Within two minutes, press the WPS button on the device that you want to connect to your WiFi network. The mobile hotspot and the wireless device automatically communicate and establish a connection. Monitor Data Usage You can monitor data usage using either the LCD screen or the web page. Visit the mobile hotspot web page to configure your monthly data usage. To view data usage on the LCD screen:

Awaken the LCD screen by pressing either the Power or the Navigation buttons. To configure your monthly data usage:

1. Launch an Internet browser from a computer or wireless device that is connected to the network. Enter http://netgear.aircard. 2. 11 3. Enter the administrator login password. The default password is password. 4. Under Billing Cycle, enter the monthly start date when your monthly data usage will automatically reset. Frequently Asked Questions Should I change my access point name (APN)?

You do not need to change or set up your APN if your mobile broadband service is working. You do need to change your APN if an alert displays on the LCD screen either prompting you to do so, or asking you to confirm the APN settings by accessing the mobile hotspot web page. Note: For information on APNs, refer to the user manual. How do I go back to the mobile hotspot web page?

Launch an Internet browser from a computer or wireless device that is connected to the network and enter http://netgear.aircard or http://192.168.1.1. What is my admin password?

The default administrator login password is password. What do I do if I changed the WiFi password or administrator login password and then forgot it?

Reset the mobile hotspot to the factory defaults. To reset the mobile hotspot, press and hold both the Navigation and Power buttons for five seconds. 12 Why cant my mobile hotspot connect to the Internet?

Confirm that your device is able to connect to your mobile hotspot:

Verify that you are connecting with the correct WiFi SSID and password. Check WiFi card stability by turning the WiFi on the computer or wireless device off and then back on. Restart your computer and restart any wireless device that is connected to the mobile hotspot. Connect with another computer or WiFi device. Turn off your mobile hotspot, remove the battery, wait 10 seconds, return the battery, and power on your mobile hotspot. Confirm that your mobile hotspot is connected to the Internet:

Note: If you do not see the data activity icons

, your mobile hotspot is not connected to the Internet. Check the alerts screen and resolve any outstanding issues. If you are using a new micro-SIM card for the first time, confirm that your micro-

SIMs APN and credentials are configured properly. Visit http://netgear.aircard and check your settings. 13 Your recharge credit might have expired. Check your account details with your Internet service provider. You may need to add an APN. For more information, refer to the user manual. Why cant I power on my mobile hotspot?

Ensure that the battery is inserted in the mobile hotspot and that it is fully charged or is charging. Optional Accessories The availability of the following optional accessories varies depending on your market:

Ethernet and antenna charging cradle. A cradle provides in-dock mobile hotspot charging and an Ethernet port and can enhance 3G/4G performance in areas with poor coverage. Extended battery. The extended battery is rechargeable and lasts for up to 16 hours of active use. WiFi range extender. An extender broadens your network coverage so that you can stay connected in every corner of your home and office. Antennas. Antennas extend signal strength and range indoors or in fringe network areas. For more information, visit http://www.netgear.com/aircardaccessories. 14 Technical Specifications Technical Specifications Network and band frequency LTE Cat 4. FDD. 700/850/1900/2600/

AWS (1700/2100) MHz 3G. 850/1700/1900/2100 MHz 2G. 850/1900 MHz WiFi connections Up to 15 users Dimensions

(WHD) 110 x 69 x 14.6 mm 4.3 x 2.7 x 5.75 inches Weight External antenna ports Standby time Operating systems 127 g TS9 Up to 300 hours Windows 8.1, 8, Windows 7, Vista SP2, and XP SP3 Mac OS 10.6.8 and later 15 Technical Support Thank you for purchasing this NETGEAR product. Contact your Internet service provider for technical support. Trademarks NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. NETGEAR, Inc. All rights reserved. Compliance For regulatory compliance information, visit:

http://www.netgear.com/about/regulatory/. See the regulatory compliance document before connecting the power supply. January 2015 NETGEAR, Inc.350 East Plumeria DriveSan Jose, CA 95134, USA