FCC ID: T58WF2420R 300Mbps Wireless-N AP/ Repeater / Router client

150Mbps/300Mbps Wireless-N AP/

Repeater/ Router client WF2412 WF2420 User Manual V1.0 2012-02-14 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Certification FCC CE FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices) FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Caution!

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. 1 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Package Contents The following items should be found in your package:

150Mbps/300Mbps Wireless-N AP/ Repeater/ Router client Power Adapter CD-Rom Ethernet cable Make sure that the package contains above items. If any of the above items is missing or damaged, please contact the store you bought this product from. Brand and Copyright Announcement Copyright 2011 Netis Corporation. All rights reserved is a registered trademark of Netis Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Reproduction in any manner without the permission of Netis Corporation is strictly forbidden All the information in this document is subject to change without notice. USA/Canada Technical Support Phone: 1-866-71-network or 1-866-716-3896 (free in USA & Canada) E-mail: usa_support@netis-systems.com 2 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Contents 1. INTRODUCTION .........................................................................................................................6 1.1. PRODUCT OVERVIEW...............................................................................................................6 1.2. MAIN FEATURES ......................................................................................................................6 1.3. SUPPORTING STANDARD AND PROTOCOL.................................................................................7 1.4. WORKING ENVIRONMENT........................................................................................................7 2. HARDWARE INSTALLATION...................................................................................................8 2.1. 2.2. 2.3. 2.4. SYSTEM REQUIREMENT ...........................................................................................................8 PANEL ......................................................................................................................................8 RESTORE TO FACTORY CONFIGURATION ...................................................................................9 HARDWARE INSTALLATION PROCEDURES ..............................................................................10 3. LOGIN.......................................................................................................................................... 11 3.1. 3.1.1. 3.1.2. 3.1.3. 3.1.4. 3.1.5. 3.1.6. CONFIGURE COMPUTER..........................................................................................................11 Windows 98/Me ............................................................................................................ 11 Windows 2000 ..............................................................................................................12 Windows XP .................................................................................................................14 Windows Vista ..............................................................................................................17 Windows 7 ....................................................................................................................22 MAC OS .......................................................................................................................24 CHECKING CONNECTION WITH THE ROUTER..........................................................................26 LOGIN....................................................................................................................................27 3.2. 3.3. 4. ROUTER SETUP ........................................................................................................................29 4.2. 4.1. 4.1.1. 4.1.2. 4.1.3. 4.1.4. 4.1.5. 4.1.6. STATUS...................................................................................................................................29 Version..........................................................................................................................29 WAN..............................................................................................................................29 LAN ..............................................................................................................................30 Wireless ........................................................................................................................30 Router Status ................................................................................................................31 Traffic Statistics............................................................................................................31 QUICK SETUP.........................................................................................................................31 DHCP (dynamic)..........................................................................................................31 PPPoE..........................................................................................................................32 Static.............................................................................................................................32 Wireless Configuration.................................................................................................33 MAC Clone...................................................................................................................33 4.3. WPS SETTINGS......................................................................................................................34 WPS Settings ................................................................................................................34 Add a New Device ........................................................................................................34 WPS Configuration ......................................................................................................36 NETWORK..............................................................................................................................36 4.2.1. 4.2.2. 4.2.3. 4.2.4. 4.2.5. 4.3.1. 4.3.2. 4.3.3. 4.4. 3 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 4.6. 4.4.1. 4.5.1. 4.5.2. 4.4.2. 4.4.3. 4.4.4. 4.4.5. 4.5.3. 4.5.4. 4.5.5. 4.5.6. 4.5.7. WAN..............................................................................................................................36 4.4.1.1. Wired Access..........................................................................................................................36 4.4.1.2. Wireless Access......................................................................................................................37 LAN ..............................................................................................................................38 MAC Clone...................................................................................................................38 Port Settings.................................................................................................................38 IGMP Proxy .................................................................................................................39 4.5. WIRELESS ..............................................................................................................................39 Wireless Settings...........................................................................................................39 Wireless Security ..........................................................................................................40 4.5.2.1. None.......................................................................................................................................41 4.5.2.2. WEP.......................................................................................................................................41 4.5.2.3. WPA-PSK ..............................................................................................................................42 4.5.2.4. WPA2-PSK ............................................................................................................................42 4.5.2.5. WPA/WPA2-PSK...................................................................................................................42 Wireless MAC Filtering................................................................................................43 WDS Settings................................................................................................................44 Wireless Advanced........................................................................................................44 Wireless Statistics .........................................................................................................46 Multiple AP Settings.....................................................................................................46 DHCP....................................................................................................................................47 DHCP Settings .............................................................................................................47 DHCP Clients List........................................................................................................47 Address Reservation.....................................................................................................47 FORWARDING.........................................................................................................................48 Virtual Servers..............................................................................................................48 Port Triggering.............................................................................................................48 DMZ .............................................................................................................................49 UPnP............................................................................................................................49 FTP Private Port..........................................................................................................50 SECURITY ..............................................................................................................................50 Security Settings...........................................................................................................50 IP Address Filtering .....................................................................................................51 MAC Filtering ..............................................................................................................52 Domain Filtering..........................................................................................................53 STATIC ROUTING....................................................................................................................53 4.9. 4.10. QOS SETTINGS ......................................................................................................................55 4.11. DYNAMIC DNS......................................................................................................................55 4.12. SYSTEM TOOLS ......................................................................................................................56 Firmware......................................................................................................................56 4.12.1. Time Settings ................................................................................................................56 4.12.2. 4.12.3. Password ......................................................................................................................57 4.12.4. WOL .............................................................................................................................57 System Logs..................................................................................................................57 4.12.5. 4.7.1. 4.7.2. 4.7.3. 4.7.4. 4.7.5. 4.8.1. 4.8.2. 4.8.3. 4.8.4. 4.6.1. 4.6.2. 4.6.3. 4.7. 4.8. 4 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 4.12.6. 4.12.7. 4.12.8. Remote Management....................................................................................................58 Factory Defaults...........................................................................................................58 Reboot ..........................................................................................................................58 4.13. ABOUT...................................................................................................................................59 5. TROUBLESHOOTING..............................................................................................................59 5 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 1. Introduction Product Overview 1.1. is dedicated 150Mbps/300Mbps Wireless-N AP/ Repeater/ Router client to Small Office/Home Office (SOHO) Wireless network solution. It is 4 in 1 network device, which combines wireless access point, firewall, 4-port Switch and the NAT-Router. It provides up to 150Mbps/300Mbps data transmission rate in 2.4GHz frequency, complies with IEEE 802.11n, IEEE 802.11g and IEEE802.11b and backwards compatible with all IEEE 802.11n/g/b devices. And the router also supports wireless LAN up to 128-bit WEP, WPA/WPA2 encryption security. The 150Mbps/300Mbps Wireless-N AP/ Repeater / Router client also provides WEB and Remote Management and system log so that network administrators can manage and monitor the network in real time. The 150Mbps/300Mbps Wireless-N AP/ Repeater/ Router client also provides a hardware WPS (Wi-Fi protected setup) button, which helps you setup a secure wireless network in a snap. The button lets you activate the wireless protection easily. 1.2. Main Features Comply with IEEE802.11n/g/b, IEEE802.3 10Base-T, IEEE802.3u 100Base-TX standards Support DHCP Client, PPPoE Client, Static IP, L2TP, PPTP Support multi-wireless mode: AP, WDS, AP+WDS, repeater, client, etc. Support static ARP, MAC filtering, IP access control, DNS filter Support FTP, PPTP and L2TP pass through Support UPNP (universal plug and play) Upgradeable firmware for future functions WPS button can easily setup a secure network Support WMM Support data encryption mode: WEP, WPA, WPA2 Support DMZ 6 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Supporting Standard and Protocol 1.3. IEEE 802.11b/g/n IEEE 802.11e IEEE 802.11h IEEE 802.11k IEEE 802.11i IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX 1.4. Working Environment Temperature 0 to 40 C (operating)

-40 to 70 C (storage) Humidity 10% to 90 % non-condensing (operating) 5% to 90% non-condensing (storage) Power DC 9V 7 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 2. Hardware Installation System Requirement 2.1. Minimum Requirements:

Broadband (DSL/Cable) modem and service with Ethernet port 802.11n b/g/n wireless adapter or Ethernet adapter and cable for each computer Internet Explorer 5.0, Firefox 2.0 or Safari 1.4 or higher Panel 2.2. Front panel LED Figure 2-1 Function 8 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual SYS WPS Normal ON and Off Abnormal Flashing Flashing slowly OFF WPS is running WPS is not running On WAN Connection normal WAN Flashing 1X-4X Off On Flashing Off Data transmitting WAN Connection abnormal LAN Connection normal Data transmitting LAN Connection abnormal Rear panel Description Figure 2-2 Function SYS Default WPS WAN 1X-4X Connect to Power adapter, please dont use the unknown power adapter, otherwise your device may be damaged. Restore settings WPS Encryption button Internet access Connect with computer NIC or Ethernet device Restore to factory configuration 2.3. If the router ever freezes in a setting change process or if you cant access it because you cant remember the IP you have given it or other problem, you may have to utilize the reset button on the back of the router to put it back to factory settings. You have to press and hole this 9 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual button for a few seconds (2-6s) with a pencil when it is working, then release and it will restore settings to the factory configuration. The other way to restore factory settings is through the same user interface used in setup. Click on System management- Restore, and click on the Restore button. Hardware Installation Procedures 2.4. The procedures to install the 150Mbps/300Mbps Wireless-N AP/ Repeater / Router client please refers to the following picture Figure 2-3 Attach one end of an Ethernet cable to your computers Ethernet port, and the other end to one of the LAN ports of your router. Connect another Ethernet cable from your Cable/DSL modem to the WAN port of your router. Connect the single DC output connector of the power adapter to the power jack on the back of the router and plug the Power Adapter into an AC outlet. 10 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 3. Login You can manage the 150Mbps/300Mbps Wireless-N AP/ Repeater / Router client through the Web browser-based configuration utility. To configure the device via Web browser, at least one properly configured computer must be connected to the device via Ethernet or wireless network. The 150Mbps/300Mbps Wireless-N AP/ Repeater / Router client is configured with the default IP address of 192.168.1.1 and subnet mask of 255.255.255.0 and its DHCP server is enabled by default. Before setting up the Router, make sure your PCs are configured to obtain an IP address automatically from the Router by the steps below. Configure computer Windows 98/Me 3.1. 3.1.1. 1. Go to Start Settings Control Panel. 2. Find and double-click the Network icon. The Network dialog box appears. 3. Click the Configuration label and ensure that you have network card. 4. Select TCP/IP. If TCP/IP appears more than once, please select the item that has an arrow pointing to the network card installed on your computer. DO NOT choose the instance of TCP/IP with the words Dial Up Adapter beside it. 5. Click Properties. The TCP/IP Properties dialog box appears. 6. Ensure the Obtain IP Address Automatically is checked. 7. From the WINS Configuration dialog box, Ensure that Disable WINS Resolution is checked. 8. From the Gateway dialog box, remove all entries from the Installed gateways by selecting them and clicking Remove. 9. From the DNS Configuration dialog box, remove all entries from the DNS Server Search Order box by selecting them and clicking Remove. Remove all entries from the Domain Suffix Search Order box by selecting them and clicking Remove. Click Disable DNS. 10. Click OK, back to Network Configuration dialog box 11. Click OK, if prompted to restart, click YES. 11 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Windows 2000 3.1.2. Please follow the steps below to setup your computer:

1. Go to Start Settings Control Panel Figure 3-1 2. Double click the icon Network and Dial-up Connections 3. Highlight the icon Local Area Connection, right click your mouse, and click Properties 12 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 4. Highlight Internet Protocol (TCP/IP), and then press Properties button Figure 3-2 Figure 3-3 5. Choose Obtain an IP address automatically and Obtain DNS server address automatically, and then press OK to close the Internet Protocol (TCP/IP) Properties window 13 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 6. Press OK to close the Local Area Connection Properties window Figure 3-4 Figure 3-5 Windows XP 3.1.3. Please follow the steps below to setup your computer:

1. Go to Start Settings Control Panel 14 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 2. Click Network and Internet Connections 3. Click Network Connections Figure 3-6 4. Highlight the icon Local Area Connection, right click your mouse, and click Properties Figure 3-7 15 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 5. Highlight Internet Protocol (TCP/IP), and then press Properties button Figure 3-8 Figure 3-9 6. Choose Obtain an IP address automatically and Obtain DNS server address automatically, and then press OK to close the Internet Protocol (TCP/IP) Properties window 16 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 7. Press OK to close the Local Area Connection Properties window Figure 3-10 Figure 3-11 Windows Vista 3.1.4. Please follow the steps below to setup your computer:

1. Go to Start Settings Control Panel 17 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 2. Click Network and Sharing Center 3. Click Manage Network Connections Figure 3-12 4. Highlight the icon Local Area Connection, right click your mouse, and click Properties Figure 3-13 18 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 5. Highlight Internet Protocol Version 4 (TCP/IP) and then press Properties button Figure 3-14 19 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 3-15 6. Choose Obtain an IP address automatically and Obtain DNS server address automatically, and then press OK to close the Internet Protocol (TCP/IP) Properties window 20 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 7. Press OK to close the Local Area Connection Properties window Figure 3-16 21 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 3-17 Windows 7 3.1.5. 1. Please follow the steps blow to setup your computer:

2. Go to Start Control Panel Network and Internet. 3. Click Network and Sharing Center Change adapter settings. 4. Highlight the icon Local Area Connection, right click your mouse, and click Properties. Highlight Internet Protocol version 4 (TCP/IPv4). 22 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 3-18 Figure 3-19 5. Choose Obtain an IP address automatically and Obtain DNS server address automatically, 23 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual and then press the OK to close the window. 6. Press OK to close the Local Area Connection Properties window. Figure 3-20 MAC OS 3.1.6. Please follow the steps blow to setup your computer:

1. Go to Start System preference Settings Network. 24 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 2. Click Network, Select Use DHCP at the Configuration bar, the system will get the IP Figure 3-21 address automatically. Figure 3-22 25 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Press Apply to complete this operation and close the window. Checking Connection with the Router 3.2. After configuring the TCP/IP protocol, use the ping command to verify if the computer can communicate with the Router. To execute the ping command, open the DOS window and Ping the IP address of the 150Mbps/300Mbps Wireless-N AP/ Repeater / Router client at the DOS prompt:

For Windows 98/Me: Start -> Run. Type command and click OK. For Windows 2000/XP: Start -> Run. Type cmd and click OK. For Windows Vista/7:Start Type cmd at the start search bar and press the Enter. For MAC OS The system will complete this operation automatically. At the DOS prompt, type the following command:

If the Command window returns something similar to the following:

C:\Documents and Settings\admin>ping 192.168.1.1 Pinging 192.168.1.1 with 32 bytes of data:

Reply from 192.168.1.1: bytes=32 time=1ms TTL=64 Reply from 192.168.1.1: bytes=32 time=1ms TTL=64 Reply from 192.168.1.1: bytes=32 time=1ms TTL=64 Reply from 192.168.1.1: bytes=32 time=1ms TTL=64 Ping statistics for 192.168.1.1:

Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds:

Minimum = 1ms, Maximum = 1ms, Average = 1ms Then the connection between the router and your computer has been successfully established. If the computer fails to connect to the router, the Command window will return the following:

C:\Documents and Settings\admin>ping 192.168.1.1 Pinging 192.168.1.1 with 32 bytes of data:

26 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.1.1:

Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), Verify your computer's network settings are correct and check the cable connection between the router and the computer. In order to make the whole network operate successfully, it is necessary to configure the 150Mbps/300Mbps Wireless-N AP/ Repeater / Router client through your computer has a WEB browser installed. Please follow up the steps listed below. Login 3.3. Open a web browser (Safari, Internet Explorer, etc.) on the computer you have just connected to the router, type http://192.168.1.1 in the address bar, and press enter. You will login the UI automatically Figure 3-18 After you have logged in, the router's user interface will be displayed. The left menu 27 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual shows the main options to configure the system, and the right screen is the summary information for viewing and adjusting the configurations. Figure 3-19 28 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 4. Router Setup Status 4.1. This feature provides running status information and detailed information about router. Version 4.1.1. Show the hardware version and firmware version. Figure 4-1 WAN 4.1.2. This feature provides running status information of the WAN port (the port connect to the Internet) Figure 4-2 Connection Type: Display routers current connection type, It should be one of PPPoE, DHCP, Static IP, depending on what kind of connection type your ISP provides. Physical Address: The physical address of WAN port, this is a unique address assigned by manufacturer. IP Address: The IP address you obtained after connect to the Internet, if you havent connected to the Internet yet, this field is 0.0.0.0. 29 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Subnet Mask: The Subnet mask you obtained after connect to the Internet, if you havent connected to Internet yet, this field is 0.0.0.0. Default Gateway: The IP address of Default gateway you obtained after connect to the Internet, if you havent connected to Internet yet, this field is 0.0.0.0. Primary DNS: The DNS server translates domain or website names into IP address, input the most common DNS server address you used or provided by your ISP. Secondary DNS: Input IP address of a backup DNS server or you can leave this field blank Link Status: Show the current status of link information. You can choose connect or disconnect by manually. LAN 4.1.3. This item provides information about routers LAN port, display LAN ports physical address, IP address and current situation of DHCP server. Figure 4-3 Wireless 4.1.4. This item provides current running information of wireless. Figure 4-4 Wireless status: Display wireless interface status is enabled or not Name (SSID): SSID (Service Set Identifier) is your wireless network's name shared among all points in a wireless network. Mode: Current wireless mode of wireless router 30 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Channel: Display current channel of your wireless router. MAC Address: The MAC address is used for wireless communication WPS Status: Display WPS (Wi-Fi Protected Setup) status is enabled or not. Router Status 4.1.5. This item provides current running information of System. Figure 4-5 Traffic Statistics 4.1.6. This item provides statistics information about the bits router sends and received. Figure 4-6 Quick Setup 4.2. Providing you the convenient and simplest method for configure the router, the purpose of this item is to provide an easy way for you to use it and configure your router to access the Internet quickly; including DHCP dynamic , PPPoE, Static and Wireless Configuration. This is the most convenient tool for you to configure router. DHCP (dynamic) 4.2.1. After select this item, you will obtain an IP address from your ISP automatically, those ISP who supply Cable modem always use DHCP technology. 31 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual PPPoE 4.2.2. Figure 4-7 Figure 4-8 If your ISP provides you the PPPoE service (all ISP with DSL transaction will supply this service, such as the most popular ADSL technique), please select this item. In the Convenient configuration You can input your PPPoE username and password to access the Internet. PPPoE Username: Input PPPoE username provided by ISP PPPoE Password: Input PPPoE password provided by ISP. Static 4.2.3. Figure 4-9 This item should only be used when users use a static IP address to access Internet, you should input your WAN IP address, subnet mask, default gateway and DNS server

(domain name server) according to the information provided by your ISP. And every IP address should be input in appropriate IP field, a IP address only divided into four IP octets by sign. is acceptable. WAN IP address: The IP address that your Internet access into Subnet mask: Specify a Subnet Mask for your WAN segment 32 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Default gateway: It is provided by your ISP Primary DNS: DNS server is used for resolve domain name. Your ISP will provides you with at least one DNS IP address, input IP address of your DNS server in this field Secondary DNS: Input IP address of backup DNS server, or you can leave this field blank. Wireless Configuration 4.2.4. You can choose Enable or Disable to enable or disable the wireless function. The default setting is enable. If you chose the Disable status, the router will become a wired broadband router without wireless function, so be careful when you choose this status. Figure 4-10 SSID: SSID (Service Set Identifier) is your wireless network's name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters. Make sure all points in the wireless network have the same SSID. For added security, you should change the default SSID to a unique name. Region: Choose a correct region which fit your use environment. Channel: Wireless router communicates to wireless cards in a particular channel, which can reduce interference between different channels. Authentication Type: Different authentication types use different encryption types, which can encrypt wireless data to protect your wireless communication. MAC Clone 4.2.5. The WAN port of router has a unique MAC address assigned by manufacturer; it called as Default MAC. The Clone MAC is used for some special situations; For example, ISP only allows certain MAC address to access the Internet, thus you can modify your WAN ports MAC address in accord with the requirement of ISP, avoiding ISPs detection. 33 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 4-11 4.3. WPS Settings Wi-Fi Protect Setup (WPS) function can let you create a safety network easily. You can through PIN Input Config (PIN) or Push Button (PBC)to encrypt your network. This router also provides WPS button, you only need to push the WPS button in this router and the wireless network card that support WPS function, then the router will be encrypted to WPA2-AES mode automatically Note:

If you have configured encryption mode in your router, then when you use this WPS function, please configure the authentication type to none, and then it will be encrypted to WPA2-AES mode automatically. If you dont want to change your authentication type, then when you use this function, the router will be encrypted to the mode that you have configured. WPS Settings 4.3.1. WPS Status: You can use this function to setup the wireless connection between this router Figure 4-12 and wireless network card. The default is Enable. AP PIN Code: This code can mark a wireless product. Add A New Device: Add a new device by WPS. Add a New Device 4.3.2. Figure 4-13 34 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Enter the new devices PIN: This code can mark a wireless product. Press the button of the new device in two minutes: New device will send a PIN code to wireless router. WPS can connect the wireless adapter and the router in a safe way. If you have a wireless network card which has WPS button, you may set up a safe network via the following methods. Method 1:

1. Push the WPS button in the Router until the WPS LED is flashing several times. 2. Push the WPS button in the wireless network card for about 3-5seconds. 3. The safe connection will be established automatically. Method 2:

1. Input the PIN code of the adapters WPS page into the routers WPS configure page, then click connect. Figure 4-14 Figure 4-15 2. Push the PIN Input Config (PIN) in the Wi-Fi protect setup of the adapter Figure 4-16 3. Select this router in the pop-up window, then click Select 4. The connection between the adapter and the router is be established automatically. Method 3:

1. Select Input PIN from AP in WI-FI protect setup page, input PIN of the router, then click PIN Input Config (PIN) 2. Select this router in the pop-up window, then click Select 3. The connection between the adapter and the router is be established automatically. Remark If there is more than one AP in the PBC mode when you use the method 1, there will be session overlap. Please using method 2/3 or wait for a while push the button again. 35 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual WPS Configuration 4.3.3. Display the WPS configuration information. Figure 4-17 Network WAN 4.4. 4.4.1. This item provides two access types for you to configure the WAN parameters. They are wired access and wireless access. 4.4.1.1. Wired Access Figure 4-18 Internet Access Type: Ask for your ISP to get the correct access type. IP: The IP address you obtained after connect to the Internet, if you havent connected to the Internet yet, this field is 0.0.0.0. Subnet Mask: The Subnet mask you obtained after connect to the Internet, if you havent connected to Internet yet, this field is 0.0.0.0. Gateway: The IP address of Default gateway you obtained after connect to the Internet, if 36 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual you havent connected to Internet yet, this field is 0.0.0.0. MTU: The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network transmission. Most DSL users should use the value 1492.You can set MTU manually, and you should leave this value in the 1200 to 1500 range. If the value you set is not in accord with the value ISP provide, it may causes some problems, such as fail to send Email, or fail to browse website. So if that happen, you can contact your ISP for more information and correct your routers MTU value. Primary DNS: The DNS server translates domain or website names into IP address, input the most common DNS server address you used or provided by your ISP. Secondary DNS: Input IP address of a backup DNS server or you can leave this field blank. 4.4.1.2. Wireless Access Figure 4-19 SSID:SSID (Service Set Identifier) is your wireless network's name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters. Make sure all points in the wireless network have the same SSID. For added security, you should change the default SSID to a unique name. Authentication Type: None means do not encrypt wireless data. Internet Access Type: Ask for your ISP to get the correct access type. IP: The IP address you obtained after connect to the Internet, if you havent connected to the Internet yet, this field is 0.0.0.0. Subnet Mask: The Subnet mask you obtained after connect to the Internet, if you havent connected to Internet yet, this field is 0.0.0.0. Gateway: The IP address of Default gateway you obtained after connect to the Internet, if 37 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual you havent connected to Internet yet, this field is 0.0.0.0. MTU: The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network transmission. Most DSL users should use the value 1492.You can set MTU manually, and you should leave this value in the 1200 to 1500 range. If the value you set is not in accord with the value ISP provide, it may causes some problems, such as fail to send Email, or fail to browse website. So if that happen, you can contact your ISP for more information and correct your routers MTU value. Primary DNS: The DNS server translates domain or website names into IP address, input the most common DNS server address you used or provided by your ISP. Secondary DNS: Input IP address of a backup DNS server or you can leave this field blank. LAN 4.4.2. The IP address of LAN port is used for access router itself by computers that connect to the router directly; here you can set IP address you need. The IP address format is like

***.***.***.***, and default IP address is 192.168.1.1, the default subnet mask is 255.255.255.0. Figure 4-1 MAC Clone 4.4.3. The WAN port of router has a unique MAC address assigned by manufacturer; it called as Default MAC. The Clone MAC is used for some special situations; For example, ISP only allows certain MAC address to access the Internet, thus you can modify your WAN ports MAC address in accord with the requirement of ISP, avoiding ISPs detection. Figure 4-21 Port Settings 4.4.4. Here you can set the router's WAN and LAN interfaces work at 100M duplex,100M 38 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual half-duplex,10M duplex and 10M half-duplex communication mode. Figure 4-22 IGMP Proxy 4.4.5. Here you can set the IGMP Proxy Enabled and Disabled. Figure 4-23 4.5. Wireless Wireless Settings 4.5.1. Providing basic configuration items for wireless router users, including wireless network status, SSID, Radio Band, Radio Mode, MAC, SSID broadcasting, Channel width, Channel sideband, Region and Channel several basic configuration items. 39 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 4-24 Wireless network status: You can choose enable or disable to enable or disable the Wireless Network Status, if what you choose is Disable, the AP function of wireless router will be turned off. SSID: The default is trst1. Radio band: You can select the wireless standards running on your network, if you have Wireless-N, and Wireless-B/G devices in your network, keep the default setting, 802.11b+g+n Radio mode: You can select radio mode of wireless router, it contains Access Point, Client, AP+WDS and WDS. The default setting is AP mode. MAC: Wireless routers physical address. SSID Broadcasting: You can select enable or disable to enable or disable the broadcast SSID function, If the setting of this field is disable, wireless client cant obtain this SSID to login in, then user have to input the SSID value manually. Channel width: This switch allows you to set Router's wireless bandwidth. 20MHz: In this mode you can get low bandwidth, little interference and slow rate. 40MHz: In this mode you can get high bandwidth, high interference and rapid rate. Use only when you have a pure router, draft 802.11n wireless network. Channel sideband: It controls your wireless router use higher or lower channel when working on 40MHz. Region: please select the region where you live in. Channel: In 20MHz, you can select one channel from 1 to 13 manually, and in 40MHz, you can select one channel from 1 to 9 or 5 to 13, which provides a choice of avoiding interference. Wireless Security 4.5.2. The item allows you to encrypt your wireless communication, and you can also protect your 40 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual wireless network from unauthorized user access. It supplies None, WEP, WPA-PSK, WPA2-PSK and WPA/WPA2-PSK five different encryption modes. 4.5.2.1. None None means do not encrypt wireless data. 4.5.2.2. WEP Figure 4-25 Figure 4-26 Key Length: There are two basic levels of WEP encryption, 64 bits and 128 bits, the more bits password have, the better security wireless network is, at the same time the speed of wireless is more slower. Key Mode: If you select WEP to encrypt your data, choose the bits of password, it should be 64 bits or 128 bits. Then choose the format of password; it should be HEX or ASCII. The valid character for HEX format should be numbers from 0 to 9 and letters from A to F. HEX support mixed letter and number mode. And ASCII supports all characters that in keyboard. Key Length description: When you select 64bits, you need to input 10 chars for HEX and 5 chars for ASCII, and when you select 128bits, you need to input 26 chars for HEX and 13 chars for ASCII. Note: When the WPS is enabled, please not use WEP. 41 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 4.5.2.3. WPA-PSK Figure 4-27 Encryption type: You can select the algorithm you want to use, TKIP, AES or TKIP&AES. TKIP means Temporal Key Integrity Protocol, which incorporates Message Integrity Code (MIC) to provide protection against hackers. AES, means Advanced Encryption System, which utilizes a symmetric 128-Bit block data. Key Renewal: you can configure the renewal time between 60 to 86400 seconds. Key Length description: you need to input 8 to 63 ASCII characters no matter which type you select. 4.5.2.4. WPA2-PSK The WPA2-PSK is similar to WPA-PSK and with stronger encryption method than WPA-PSK, using WPA2-PSK; you should input password (leave this value in the range of 8 to 63 characters) and key renewal time (leave this value in the range of 60 to 86400 seconds). Figure 4-28 4.5.2.5. WPA/WPA2-PSK This item mixed WPA-PSK and WPA2-PSK mode, which provides higher security level; you can configure it according with WPA-PSK or WPA2-PSK. 42 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 4-29 Wireless MAC Filtering 4.5.3. Figure 4-30 MAC Filter Status: the default is disable. You can filter wired users by enabling this function; thus unauthorized users can not access the network. Description: describe MAC Filter list to tell from different MAC Filter lists. Rule: you can select permit or deny. The default is permit. MAC address: input the MAC address that you want to control. The default format is

**-**-**-**-**-**e.g.: 00-22-33-da-cc-bb. Follow the following steps to set MAC filter:

1. Enable MAC Filter, then select save. 2. Add MAC address you want to control in the MAC address field (the format is

**-**-**-**-**-**), then click Add button, and you will see the MAC address has displayed in the MAC list. 3. There are two items supplied, Permit wireless connection for MAC address listed (others are Denied) and Deny wireless connection for MAC address listed (others are Permitted), 43 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Select the item you want, and click Save button. WDS Settings 4.5.4. If you have selected WDS or AP+WDS mode in Wireless Basic-Radio Mode, please do the following configurations. Figure 4-2 WDS Name: Give a description of your wireless bridge to tell apart. WDS MAC Address: If the current working mode is WDS or AP+WDS, then you need to configure wireless bridge configuration. Enter MAC address of remote access point, at the same time the remote access point also need to configure to WDS or AP+WDS mode. Current WDS Information: It illustrates basic information of all wireless bridge that in connection status, you may delete unnecessary bridge. E.g.: If you want setup WDS connection between the AP that the MAC address is 00-22-4f-cc-ae-f5 (we call it AP1) and the AP that the MAC address is 00-22-4f-bc-af-5d (we call it AP2), please follow the next steps:

1. Select radio mode is WDS in wireless management-basic of AP1. 2. Input WDS name (e.g.: default), input MAC address of AP2 (00-22-4f-bc-af-5d), click add, then the record named default will appears in WDS list. 3. We can also select radio mode is WDS in wireless management-basic of AP2. 4. Input WDS name (e.g.: Default), input MAC address of AP1 (00-22-4f-cc-ae-f5), click add, then the record named Default will appears in WDS list. Note: Before you setup WDS connection, please make sure that AP1 and AP2 is in the same network, that is if the IP address of AP1 is 192.168.1.1, then the IP address of AP2 should be 192.168.1.x (1<x<255,e.g.: x=8). Wireless Advanced 4.5.5. These settings are only for more technically advanced users who have a sufficient knowledge 44 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual about wireless LAN. These settings should not be changed unless you know what effect the change will have on your AP. Figure 4-32 Authentications type: The default is set to Auto, which allows Open System or Shared Key authentication to be used. Select Shared Key if you only want to use Shared Key authentication (the sender and recipient use a WEP key for authentication). Beacon Interval: The interval time of this 150Mbps/300Mbps Wireless-N AP/ Repeater /

Router client broadcast a beacon. Beacon is used to synchronize the wireless network. The valid interval is 20-1000, the default is 100. RTS Threshold: You can set RTS Threshold value in this field, the valid range should be 256-2347 and default value is 2347. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. Aggregation: You can accelerate the wireless transmission speed by enabling the aggregation function. The default is AMPDUAMSDU. Fragmentation Threshold: It specifies the maximum size of packet during the fragmentation of data to be transmitted. Transmission Rate: Transmit rate indicates the transmission speed of wireless LAN access .The default setting is Auto and you can set this value between 1-54Mbps range. ShortGi: You can select Enable or disable for shortgi. Protection: Using 802.11b and 802.11g mixed mode may result in poor network performance. By enabling 802.11 protection, it will ameliorate performance of 802.11g devices in your wireless network. 45 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Preamble Type: "Short Preamble" is suitable for heavy traffic wireless network. "Long Preamble" provides much communication reliability; the default setting is "Long Preamble. Wireless Statistics 4.5.6. Display current status of the wireless client associate with AP. Figure 4-32 Multiple AP Settings 4.5.7. The default status of secondary AP is disable, you can select enable to enable the secondary AP. Please refer to Quick Setup Wireless Security and Wireless Statistics for details. Figure 4-33 46 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual DHCP DHCP Settings 4.6. 4.6.1. Figure 4-34 DHCP Clients List 4.6.2. Display the state of assigned IP by DHCP Server. Figure 4-35 Address Reservation 4.6.3. Figure 4-36 Address Reservation: reserve IP address for designed physical address host. If you want to configure a fixed IP address for some host, please input physical address and IP address, then click add. 47 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Forwarding Virtual Servers 4.7. 4.7.1. Figure 4-37 Description: Describe current virtual server item. Internal Host IP Address: The Internal Host IP Address indicates IP address of the internal host using virtual server. Protocol: The protocol item supplies several protocols. For example, if you have web server within LAN, you can select the HTTP template then the router will input port number 80 automatically. External Port: Input an extranet port number (the users in Internet can see these ports). Internal Port: Input an intranet port number. Port Triggering 4.7.2. Port trigger module dynamically registers virtual server rules when any IP host generates the packet from the specified trigger protocol and port. Port trigger module use forward protocol type and port number and use the IP address of host that generates the trigger packet when it registers a rule. 48 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 4-38 Predefined Trigger Rules: select one of the Predefined Rules. Rule Name: describe one Predefined Trigger that you will configure. Trigger Protocol: you can select TCP/UDP. Trigger Port: you can select a part of ports. Forward Protocol: you can select TCP/UDP. Forward Port: you can select a part of ports. DMZ 4.7.3. DMZ opens all the ports of one computer, exposing the computer to the Internet. So it should only be used for some special-purpose, especial for Internet online games. Using this function you can select DMZ item and input IP address of DMZ host, then click Save. For the purpose of security, we suggested that using Virtual servicer instead of DMZ. Figure 4-39 UPnP 4.7.4. The UPnP function supports load Applications port forward record automatically. Select Enable to enable this function. 49 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 4-40 FTP Private Port 4.7.5. Some games, servers, and applications (such as BT, QQ video, Edunkey, Web server) are no longer effect when behind the NAT router, so this item provides function of port mapping from LAN to WAN. Figure 4-41 Security Security Settings 4.8. 4.8.1. VPN is commonly used for encapsulate and encrypt data across the public network. For VPN tunnel, the router supports IPSEC pass-through, PPTP pass-through and L2TP pass-through. Figure 4-42 50 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual IP Address Filtering 4.8.2. Status: the default is disable. The rules of Internet access control based on source IP, Figure 4-43 port number and protocol. Description: describe IP Firewall list to tell from different IP Firewall lists. Rule: you can select permit or deny. The default is permit. Source IP address: input the source IP address that you want to control. The default format is ***.***.***.***(e.g: 192.168.2.3). Protocol and Port: If the rule has already existed in Protocol Template. You can select appropriate item and apply it. Or you can input protocol type and port number manually, click add button, then the item will displayed in the list. Follow the following steps to set Internet Access Control:

1. You can select enable and click Save to enable IP Firewall function. This is only the first step; you should continue to create appropriate rules for IP Firewall. 2. Input description information for current access control rule in the Description field. Input IP address of host you want to restrict. 3. There are two items supplied, Permit through the router for IP address listed, others are denied and Deny through the router for IP address listed, others are permitted, Select the item you want, and click Save button. 51 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual 4. If you want to delete certain item on the list, select appropriate item on the list, click delete to delete it. MAC Filtering 4.8.3. Figure 4-44 Status: the default is disable. You can filter wired users by enabling this function; thus unauthorized users can not access the network. Description: describe MAC Filter list to tell from different MAC Filter lists Rule: you can select permit or deny. The default is permit MAC address: input the MAC address that you want to control. The default format is

**-**-**-**-**-**e.g.: 00-22-33-da-cc-bb Follow the following steps to set MAC filter:

1. Enable MAC Filter, then select save. 2. Add MAC address you want to control in the MAC address field (the format is

**-**-**-**-**-**), then click Add button, and you will see the MAC address has displayed in the MAC list. 3. There are two items supplied, Permit wireless connection for MAC address listed (others are Denied) and Deny wireless connection for MAC address listed (others are Permitted), Select the item you want, and click Save button. 52 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Domain Filtering 4.8.4. Status: the default is disable. DNS filter is able to filter certain domain name such as Figure 4-45 www.sina.com. Rule: you can select permit or deny. The default is permit. DNS Filter Key words: Input website name or Domain name in the DNS Key Words field, such as www.163.com. Follow these steps to set DNS filter:

1. You can select enable and click Save to enable DNS Filter function. This is only the first step, you should continued to create appropriate rules for DNS Filter. 2. Input DNS Filter Key words. 3. There are two items supplied, Permit through the router for DNS Key words listed, others are denied and Deny through the router for DNS Key words listed, others are permitted, Select the item you want, and click Save button. 4. If you want to delete certain item on the list, select appropriate item on the list, click delete to delete it. Static Routing 4.9. Most of broadband router and wireless router are using NAT mode, so this feature is designed for most common network environment. 53 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 4-46 Destination Network or IP Address: Specify a certain destination Network or IP address which static route forward to. Subnet Mask: Subnet mask is used for distinguish Network portion and Host portion for an IP address. Next-hop IP Address: This is an IP address of the next-hop device (and also is the gateway address for local host) that allows forwarding data between router and remote network or host. Routing Table: You can check out all current route items, click delete button to delete a route item existed in routing table. 54 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual QOS Settings 4.10. Figure 4-47 Status: QOS switch. Automatic Uplink Speed: Router adjusts uplink bandwidth automatically. Manual Uplink Speed (Kbps): User configures uplink bandwidth manually. Minimum bandwidth: setup uplink and downlink bandwidth. Maximum bandwidth: setup uplink and downlink bandwidth. IP Address: Set the IP address range for restricted hosts. Dynamic DNS 4.11. The DDNS feature allows you using domain name (not IP address) to access Internet. Before you can use this feature, you need to register an account for DDNS service at DDNS service providers, such as roay.cn, TZO.com, DynDNS. For more information, you can visit http://www.oray.net/Help. 55 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 4-48 DDNS Status: Current status of DDNS server. DDNS Server Provider: For example, if you want to use service of roay.cn, you have to first register and accounts for it. Other DDNS service providers as the same. Username, Password, Dynamic Domain Name: After register an DDNS account from DDNS service providers, you will get User Name, Password, Dynamic Domain Name, Input information in appropriate field. System Tools 4.12. System management includes password setup, web Setup, upgrade, reboot, restore, WOL and System time. Firmware 4.12.1. Click "Browse..."button and select a File to upgrade, after you have selected the appropriate file, click "Upgrade" button to execute upgrade procedure. Do not cut off the power supply during the process of upgrading. Figure 4-49 Time Settings 4.12.2. You can choose the time server and the time zone for the system time. 56 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 4-50 Password 4.12.3. To ensure the Routers security, it is suggested that you change the default password to one of your choice, here enter a new password and then Re-enter it again to confirm your new password. Click Save button to save settings. Figure 4-51 WOL 4.12.4. Input host MAC address, and then click button of "Wake up" to wake up the target host which in the LAN. Figure 4-52 System Logs 4.12.5. Examine system logs. You can configure items shown in one Page, the default is 10. 57 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual Figure 4-53 Remote Management 4.12.6. WEB Management Status: the default is disable. Router can be accessed on the remote site using Web setup. Check the Management Port and enter the port number and then press save button to enable web management. Figure 4-54 Factory Defaults 4.12.7. Click "Restore" button, the Router will erase all of your settings and replace them with the factory defaults, make sure you have backup current settings before click this button. Figure 4-55 Reboot 4.12.8. Click Reboot button to restart the router. Figure 4-56 58 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual About 4.13. Figure 4-57 Thank you for your support. 5. Troubleshooting 1. I cannot access the Web-based Configuration Utility from the Ethernet computer used to configure the router. Check that the LAN LED is on. If the LED is not on, verify that the cable for the LAN connection is firmly connected. Check whether the computer resides on the same subnet with the routers LAN IP address. If the computer acts as a DHCP client, check whether the computer has been assigned an IP address from the DHCP server. If not, you will need to renew the IP address. Use the ping command to ping the routers LAN IP address to verify the connection. Make sure your browser is not configured to use a proxy server. Check that the IP address you entered is correct. If the routers LAN IP address has been changed, you should enter the reassigned IP address instead. 2. I forget Password (Reset the Router without Login) Use a pencil to press the button for about 2-6 seconds when it is working, then leave your hands, it will restore settings to the factory configuration. The default username and password is Blank(no username and password required) 3. I have some problems related to Connection with Cable Modem Please follow the following steps to check the problems:

Check whether the DSL modem works well or the signal is stable. Normally there will be some indicator lights on the modem, users can check whether the signal is ok or the modem works well from those lights. If not, please contact the ISP. Check the front panel of the Router, there are also some indicator lights there. When the 59 150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual physical connection is correct, the Power light and the CPU light should be solid; the WAN light should be blinking. If you use your computer, the corresponding LAN port light should be blinking too. If not, please check whether the cables work or not. Repeat the steps in WAN Setup Connect with Internet through DSL Modem. 4. I can browse the routers Web-based Configuration Utility but cannot access the Internet. Check if the WAN LED is ON. If not, verify that the physical connection between the router and the DSL/Cable modem is firmly connected. Also ensure the DSL/Cable modem is working properly. If WAN LED is ON, open the System Overview page of the Web configuration utility and check the status group to see if the router s WAN port has successfully obtained an IP address. Make sure you are using the correction method (Dynamic IP Address, PPPoE, or Static IP) as required by the ISP. Also ensure you have entered the correct settings provided by the ISP. For cable users, if your ISP requires a registered Ethernet card MAC address, make sure you have cloned the network adapter s MAC address to the WAN port of the router.

(See the MAC Address field in WAN Setup.) 5. My wireless client cannot communicate with another Ethernet computer. Ensure the wireless adapter functions properly. You may open the Device Manager in Windows to see if the adapter is properly installed. Make sure the wireless client uses the same SSID and security settings (if enabled) as the 150Mbps/300Mbps Wireless-N AP/ Repeater / Router client . Ensure that the wireless adapters TCP/IP settings are correct as required by your network administrator. If you are using a 802.11b wireless adapter, and check that the 802.11G Mode item in Wireless Basic Setting page, is not configured to use 802.11G Performance. Use the ping command to verify that the wireless client is able to communicate with the routers LAN port and with the remote computer. If the wireless client can successfully ping the router s LAN port but fails to ping the remote computer, then verify the TCP/IP settings of the remote computer. 60

Testing Report

- 1 - / --

KCI2401 Testing Report of KCI2401 Product Antenna

: KC-17-DB-003/A0 2011/9/7

- 2 - / --

KCI2401 S Smith 1 1.1 Agilent E5071C 1 2 3 S11 Smith

- 3 - / --

1.2

(VeryCTE) 1 1 (AUT) 6.5 Theta Phi

- 4 - / --

2

(1) KC &

(2) IxChariot5.4 & Endpoint5.0

(3) 300M 150M 1 1.1 24002483MHz 1.2 50 1.3 1.4 4.10dBi

- 5 - / --

Picture : Antenna and Testing RF Connector 1 1 KCI2401

(mm) 24

(mm) 17.5

(mm) 0.4

- 6 - / --

1 S11Smith

- 7 - / --

KCI2401 S 2.40GHz 2.44GHz 2.48GHz SWR KC 1.218 Smith S11 SWR Smith S11 SWR Smith S11 47.702-j9.341

-20.166 1.177 50.350-j8.205

-21.769 1.187 55.407-j7.133

-21.419 2 2.4GHz E 2.4GHz H

- 8 - / --

2.44GHz E :

2.44GHz H

- 9 - / --

2.48GHz E 2.48GHz H

- 10 - / --

2

(1) KC 1 150M 300M 150M 1 1 150M 2 300M 3 IP //

4. , 5. 1 102.1 95.0 88.2 105.3 96.5 92.6 56.6 84.1 64.3 102.3 96.5 94.7 89.8 78.8 88.1 73.0 59.2 65.4 51.6 67.5 76.7 59.7 92.4 87.2 66.4 72.2 6 6 KC

: KCI2401

- 11 - / --

(2) 1 150M ,300M 150M 44 1 150M 2 300M 3 IP //

4. , 5. KC 6 6 44 58 58 76 55 74 37 55 49 86 70 75 35 48 58 73 88 75 68 54 55 77 72 70 61 68.4 58.8

: KCI2401

- 12 - / --

Total Test Thoughput Average Data KCI2401 Antenna KC 75 70 65 60 55 50 45 40 35 30 3. KCI2401 WLAN

- 13 - / --

Declaration of Authorization We Name: NETIS SYSTEMS CO., LTD Address: 9F,B Block, Tsinghua Information Park, High-tech Industrial Park, Nanshan City: Shenzhen . Country: China Declare that:

Name Representative of agent: Cathy Wang Agent Company name: Neutron Engineering, Inc. Address: No.3 Jinshagang 1* Road, Shixia, Dalang Town City: Dong Guan Country: China is authorized to apply for Certification of the following product(s):

Product description: 300Mbps Wireless-N AP/ Repeater / Router client Type designation: WF2420 Trademark: netis on our behalf. Date:

2012-6-8 City: Shenzhen Name: Selena Bai Function: PD Assistant SIGNOCUOI ET oc Lc cc uses SV elomo S ou(

NETIS SYSTEMS CO., LTD Ad Hoc Mode Declaration We, the undersigning company Company Name: NETIS SYSTEMS CoO., LTD Address: 9F,B Block, Tsinghua Information Park, High-tech Industrial Park, Nanshan, Shenzhen, China Hereby confirm that the following products:

Product description: 300Mbps Wireless-N AP/ Repeater / Router client Type designation: WF2420 Trademark: netis The product doesnt have Ad Hoc Mode function on non-US frequencies. In addition, the frequency selection feature is disabled by firmware for devices marketed to the US. For this product, only channels 1~11 will be used in USA. Country code selection is disabled. Signature: SeLonor Rai Name: Selena Bai

Testing Report

- 1 - / --

KCI2402 Testing Report of KCI2402 Product Antenna

: KC-17-DB-011/A0 2011/9/15

- 2 - / --

KCI2402 S Smith 1 1.1 Agilent E5071C 1 2 3 S11 Smith

- 3 - / --

1.2

(VeryCTE) 1 1 (AUT) 6.5 Theta Phi

- 4 - / --

2

(1) KC &

(2) IxChariot5.4 & Endpoint5.0

(3) 300M 150M

- 5 - / --

1 1.1 24002484MHz 1.2 50 1.3 1.4 :

Gain Freq.

(MHz) 2400.0 2440.0 2480.0 2400.0 2440.0

(dBi) 3.83 3.85 4.62 3.71 4.10 KC KCI2402 Ag N2420 3.90

: Ag N2420 . 2480.0 1 1 KCI2402

(mm) 46.5

(mm) 9

(mm) 0.5

- 6 - / --

1 S11Smith KCI2402 S :

Ag N2420 S :

- 7 - / --

S Antenna SWR Smith S11 SWR Smith S11 SWR Smith S11 2.4GHz 2.44GHz 2.48GHz KC 1.409 49.767-j17.149

-15.450 1.383 49.612-j16.230 -15.871 1.258 41.673-j6.222 -18.865 Ag 3.2174 37.070+j51.462

-5.592 2.313 62.492+j46.612

-8.039 1.625 70.841+j20.380 -12.502

- 8 - / --

2 2.4GHz E :

2.4GHz H :

- 9 - / --

2.44GHz E :

2.44GHz H :

- 10 - / --

2.48GHz E :

2.48GHz H :

- 11 - / --

2

(1) KC 1 zPlus 150Mbps xLink 300M zPlus 150Mbps 1 1 zPlus 150Mbps 2 xLink 300M 3 zPlus 150Mbps & xLink 300M IP 4. , 5. 1 75.5 80.1 66.7 83.5 75.4 71.0 84.6 91.9 76.9 89.3 93.7 78.9 80.6 100.8 88.0 76.3 51.2 87.7 76.1 92.5 81.6 83.5 80.2 82.1 72.3 81.0 6 6 KC Ag

: KCI2402

- 12 - / --

(2) 1 zPlus 150Mbps xLink 300M zPlus 150Mbps 44 1 zPlus 150Mbps 2 xLink 300M 3 zPlus 150Mbps & xLink 300M IP 4. , 5. 44 24 35 54 52 54 50 25 31 55 46 27 50 46 53 48 31 46 42 27 41 69 62 50 50 44.8 44.3 6 6 KC Ag

: KCI2402 S

- 13 - / --

3. S11 WLAN

- 14 - / --

NETIS SYSTEMS CO., LTD Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen:

This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. NETIS SYSTEMS CO., LTD would like the following documents regarding this submission for FCC ID: T58WF2420R to be kept confidential. 1. Schematics. 2. Block diagram, 3. Operation description The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely; Splonoh\

Ox |

oe ES Ee ee Contact person: Selena Bai Date: 2012-6-8