FCC ID: 2A255-STAC TAC

TECHNOLOGY FOR THE MIND NeuroTek Elite Series Standard Tac Quickstart Guide Important: Please read all instructions completely before operating this device NeuroTek 2020 Version 2.0 FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .The device has been evaluated to meet general RF exposure requirement. NeuroTek 2020 Version 2.0 Liability Disclaimer This product is a tool designed to assist the clinician in the administration of

(EMDR). The purchaser/clinician agrees to accept full responsibility for any harmful results and/or undesirable consequences obtained from the use of this machine. The manufacturer of this machine shall not be held liable for adverse affects caused to clients resulting from the administration of EMDR or any other form of therapy using this machine. Any unexpected reactions, results, or behavior noted as a result of the administration of EMDR, either using this product or by other methods, should be immediately reported to the EMDR Institute. Limited Warranty Limited Warranty The manufacturer warrants this equipment to the original purchaser against The manufacturer warrants this equipment to the original purchaser against defective material or workmanship during the warranty period from the date defective material or workmanship during the warranty period from the date of purchase. The manufacturers responsibility under this warranty is limited of purchase. The manufacturers responsibility under this warranty is limited to the repair or replacement of defective parts. to the repair or replacement of defective parts. The warranty period:

The warranty period:

One (1) year on all parts and components. The manufacturer reserves the Ninety (90) days on components that connect with wires. This includes right to determine whether the part or parts failed because of defective cables, wired pulsers, headphones and AC Adapters. One (1) year on all other material, workmanship or other causes. Failure caused by accident, normal parts and components. The manufacturer reserves the right to determine wear, alteration, misuse, tampering, negligence or improper packaging of whether the part or parts failed because of defective material, workmanship returned units is not covered by this warranty. Please be advised that if a or other causes. Failure caused by accident, normal wear, alteration, misuse, product is returned for warranty service and no defects are found or the tampering, negligence or improper packaging of returned units is not cov-

problem is due to a weak/dead battery or operator error a shop charge and ered by this warranty. This warranty is void when product is used by multiple return shipping costs may be charged. All warranty repairs must be done by therapists in a shared environment. Please be advised that if a product is NeuroTek or a representative designated by NeuroTek. Any repair to the returned for warranty service and no defects are found or the problem is due equipment other than by these authorized facilities voids this warranty. The to a weak/dead battery or operator error a shop charge and return shipping rights under this warranty are limited to the original purchaser and may not costs may be charged. All warranty repairs must be done by NeuroTek or a be transferred to subsequent owners. To receive warranty service, you must representative designated by NeuroTek. Any repair to the equipment other first contact NeuroTek for a return authorization number. This number will than by these authorized facilities voids this warranty. The rights under this be used for tracking your return. Send the complete unit, postage paid, to warranty are limited to the original purchaser and may not be transferred to NeuroTek. Include a description of the problem you are having and a daytime subsequent owners. To receive warranty service, you must first contact Neu-

phone number. roTek for a return authorization number. This number will be used for track-

ing your return. Send the complete unit, postage paid, to NeuroTek. Include a description of the problem you are having and a daytime phone number. 17116 Journeys End Dr., Wheat Ridge CO 80033 Odessa, FL 33556 www.neurotekcorp.com www.neurotekcorp.com Phone: 303 420-8680 Fax: 303 422-9440 Phone: 727-372-0104 emdrtools@neurotekcorp.com emdrtools@neurotekcorp.com NeuroTek 2020 NeuroTek 2020 Version 2.0 Product Features Product Features Auditory Auditory Tone mode Tone mode Dual Modality - Use auditory or tactile stimulation independently or together Dual Modality - Use auditory or tactile stimulation independently or together Connectivity Connectivity Adjustments for volume, speed (rate) and tactile intensity Adjustments for volume, speed (rate) and tactile intensity Range 1 10 LED Screen provides visual speed and auditory mode information Range 1 10 LED Screen provides visual speed and auditory mode information Headphone and pulser cable (6 feet) Soothing alternative to eye movements Headphone and pulser cable (6 feet) Prevents clinician fatigue Soothing alternative to eye movements Lowers distractions for client Prevents clinician fatigue Use with visually-impaired clients or clients with a history of seizures Lowers distractions for client Use with visually-impaired clients or clients with a history of seizures Headphones, standard tactile pulsers, AC adapter and battery Optional Wired LED Pulsers available Headphones, standard tactile pulsers, AC adapter and battery Backed by our Limited one-year Warranty!

Optional Wired LED Pulsers available Backed by our Limited one-year Warranty!

Comes complete with Comes complete with Package Contents Tac Adapter Headset Pulsers Battery Available Accessories LED Pulsers NeuroTek 2020 Version 2.0 Standard Tac Quickstart Guide Standard Tac Quickstart Guide Thank you for purchasing the NeuroTek Elite Series Tac. The Thank you for purchasing the NeuroTek Elite Series Tac. The Standard Tac has and adjustment range of 110. Standard Tac has and adjustment range of 110. 1 Insert the nonchargeable CR123A battery Insert the nonchargeable CR123A battery

(included) or plug in the adapter

(included) or plug in the adapter Battery Bay NeuroTek 2020 Version 2.0 Controls for Standard Tac Navigate Power/Enter/Increment Decrement/Navigate Increment/Navigate Navigate 2 Turn ON/OFF ON: Press and hold power/enter until screen activates. OFF: Press and hold power/enter until screen is blank. 3 Tactile and Audio Connect (Wired) Wired pulser port. Wired headset port. NeuroTek 2020 NeuroTek 2020 Version 2.0 Quick Start 4 o To begin session, hold the middle button for approximately 5 seconds to turn the device on. o Plug in your pulsers and or headset into the side of the Tac. If you have an EyeScan see #4 of the manual on how to pair the EyeScan to the Tac. If you dont you can continue to the next step. o On the main screen, you will see the words Resource

(which is slower speeds), and Reprocessing (which is higher speeds). These are 2 preset profiles that you can use to get started. You do have the ability to change the settings if needed. Select which option you prefer. Once selected, the curser will automatically go down to Start Session. Press the middle button to select Start Session, and your session will begin. Your pulsers, headset, and EyeScan will begin to work. o Once they are running, if you want to adjust the speed of your devices, the volume of your headset, the settings on the EyeScan, or the intensity of your pulsers, you will use the arrows to select one of the icons in the middle of the screen. There will be a square box around the icon once its selected. So, the hand is for pulsers, the headset, is for your headset, the eye is for the EyeScan, and the last icon, a clock is for speed. Once the box is around the one you want, press the middle button to select it, and the options to adjust the speed, volume, mode, or intensity will appear. Use the arrows to make the adjustments that you want up or down. NeuroTek 2020 Version 2.0 5 Edit Profiles To edit the profiles, you would want to have all your accessories (the pulsers, headset and EyeScan if applicable) connected to the Tac in order to adjust the settings for all devices. Once they are connected, you would follow the following steps:

o From the main menu, SelectProfiles o You will then see Resource (which is set at slower speeds) and Reprocessing (which is set at higher speed). SelectEditnext to the one you want to change, and then select Start. It will walk you through the settings for each device,

(pulsers, headset, and EyeScan if applicable). o o Once completed, press Save and your changes should be saved at this point. o From the main menu, select theprofilethat you made changes to, Resource or Reprocessing and then Start, and you should see the changes in yourprofile. NeuroTek 2020 Version 2.0 Start A Session seconds see step C. A. Turn on Tac by holding the center power button for 5 seconds B. Do you have an EyeScan? If yes, continue below. If no, Start A Session 6 see step C. A. Turn on Tac by holding the center power button for 5 o Ensure your EyeScan is turned on. On your Tac, B. Do you have an EyeScan? If yes, continue below. If no, o Ensure your EyeScan is turned on. On your Tac, Select Settings, then select Wireless Devices. Your tac will automatically scan for wireless devices. Once your device is found, it will show up on your Tac. Select the device by hitting enter and then a Select Settings, then select Wireless Devices. Your check mark will appear next to the device. Arrow tac will automatically scan for wireless devices. down and select connect. OK will appear next to Once your device is found, it will show up on your the device. Tac. Select the device by hitting enter and then a check mark will appear next to the device. Arrow o Select Back until you get back to the Main Menu down and select connect. OK will appear next to the device. o Select Back until you get back to the Main Menu NeuroTek 2020 Version 2.0 C. Connect your wired devices to your Tac;

o You can plug in the headset, the pulsers, or both. The main menu C. Connect your wired devices to your Tac:

will show what devices are connected. o You can plug in the headset, the pulsers, or both. The main menu will show what devices are connected. Resources Reprocessing Pulser Headphones EyeScan Profiles Settings D. Select Start Session and it will walk you through the settings for the devices that are connected. Use the arrow buttons to increase or decrease your settings and then arrow down to next and select it to take you to the next screen. E. Select Start once your settings are selected. F. During a session you can change any of the settings on the devices you have connected. D. Select Start Session and it will walk you through the settings for the devices o Highlight the icon of the device that you want to change that are connected. Use the arrow buttons to increase or decrease your G. Highlight the icon of the device that you want to change the settings for, G. Highlight the icon of the device that you want to change the settings for, the settings for, and press enter (the middle button). settings and then arrow down to next and select it to take you to the next The hand is for pulsers, the headset is for headset, the and press enter (the middle button). The hand is for pulsers, the headset is and press enter (the middle button). The hand is for pulsers, the headset is screen. eye is for the EyeScan, and the timer icon is for the for headset, the eye is for the EyeScan, and the timer icon is for the speed for headset, the eye is for the EyeScan, and the timer icon is for the speed speed for all devices. Once selected, it will give you the for all devices. Once selected, it will give you the option to make the for all devices. Once selected, it will give you the option to make the option to make the changes. changes. changes. have connected. E. Select Start once your settings are selected. F. During a session you can change any of the settings on the devices you NeuroTek 2020 Version 2.0 End, Restart, or Pause a Session A session can be started three ways 1) Use the Start Session button in the Main Menu End, Restart, or Pause a Session 7 3) Choose any device from the Main Menu and use Start Stopping a session suspends it but gives the user the choice to continue or end the session Restart will restart the session The session can be Paused and, when pressed, the button will read Play which will continue the current session NeuroTek 2020 Version 2.0 Manually select NeuroTek headset device to pair and press connect. Other Settings for Tac Other Setting for Tac 8 Select to turn Power Savings Mode ON/OFF Power Savings Arrow to the left to adjust the screens brightness. Arrow to the left to adjust the screens brightness.

#7 End, Restart, or Pause a Session (we can keep this) just eliminate the wording above the picture. Rechargeable Battery Select this option if you have purchased a rechargeable version of the battery CR123A. You must also purchase a charger to charge the battery outside of the device. NeuroTek 2020 Version 2.0 Troubleshooting Guide Troubleshooting Guide can do a reset by inserting a paper clip into the small hole at the bottom of the Tac. When you feel the button click, release can do a reset by inserting a paper clip into the small hole at the bottom of the Tac. When you feel the button click, release The reset button is located in the same place on the bottom of all Tacs. The reset button is located in the same place on the bottom of all Tacs. o If youre pressing the buttons and they arent responding, please check to ensure you are doing a quick press and release. If you press the buttons too long while selecting your option, it wont respond. o Your device is not rechargeable. It comes with a disposable CR123A battery. There are rechargeable versions of this battery which you can buy. You must also buy a charger to charge the battery outside of the device. If you use these batteries, please go into the Settings menu and select Rechargeable Battery. Once selected, it will be in black letters. This will ensure the device will register the correct battery level. NeuroTek 2020 Version 2.0 Troubleshooting Guide o If you put in a disposable battery, and the battery level still shows low battery, please check the settings to ensure that the Disposable Battery option is selected. It will be in black letters if selected. o To extend the life of your battery, please turn on the power save mode under settings. It will dim your screen after 30 seconds of inactivity. To light the screen back up, simply press a button. Maintenance To clean the device, we recommend using a microfiber cloth to dust the device. Do not use harsh chemicals on the LCD screen as it can damage the screen over time. We do recommend using the premoistened screen wipes occasionally, if you need to clean the screen, and the cloth isnt enough. In order to extend the life of your pulsers it is important to know that the life of the wires is directly related to how much flexing, pulling and bending your pulser wires receive. Although we work very hard to make the pulsers and wires as durable as possible, there is no way to predict how long they will last. Any wire that is handled on a regular basis, especially by people who are stressed, will eventually wear out. Pulsers are considered consumable items and having spares on hand is highly recommended. For further assistance please email us at:

emdrtools@neurotekcorp.com, or call 727-372-0104. Our normal office hours are 7:30 a.m. - 4:30 p.m. EST Monday through Friday. NeuroTek 2020 Version 2.0 NeuroTek 2020 Version 2.0 17116 Journeys End Dr., Odessa, FL 33556 727-372-0104 www.neurotekcorp.com NeuroTek 2020 Version 2.0

FCC ID LABELING AND LOCATION FCC ID Label TAC Model NO.: Standard TAC FCC ID: 2A255-STAC Size:2.5cm*1.5cm FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Neurotek Technologies, LLC. 2021.09.22 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern:

We, the undersigned, hereby authorize Brown.lu to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Signature:

Name: Danielle Corkery Title: PM

Neurotek Technologies, LLC. 2021.09.22 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (TAC / Standard TAC, NT-STAC-1/ FCC ID:2A255-STAC) To Whom It May Concern:

This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the (Block Diagram/ Schematics/ Operational Description) required to be submitted with this application be permanently withheld from public review. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Please contact me if there is any information you may need. Sincerely, Signature:

Name: Danielle Corkery Title: PM

Neurotek Technologies, LLC. Model Difference FCC ID: 2A255-STAC Model : Standard TAC, NT-STAC-1 All the model are the same circuit and RF module, except the model name and colour. Regards, Clients signature Clients name / title : Danielle Corkery / PM Contact information / address :

Neurotek Technologies, LLC. 17116 Journeys End Dr., Odessa, FL, USA 33556