FCC ID: G6D1820UB TOY Receiver

TROUBLE SHOOTING & SUPPORT Problem - Vehicle does not move or moves slowly.

- Make certain there are fresh alkaline batteries in the transmitter and that they have been installed in the correct position.

- Are the (+) and () markings on the alkaline batteries in the same position as the (+) and (-) markings in the Transmitter Battery Compartment?

- Has the internal battery in the vehicl been charged?

- Are the metal contact tabs touching, rusty or dirty in the transmitter?

- Make certain that the vehicle ON/OFF switch is in the ON position. Problem - Vehicle moves by itself or exhibits reduced range from the transmitter.

- Make certain there is no outside radio interference in your area. The best way to test this is to

- take the vehicle as far away from radio towers, electrical lines or tall buildings as possible to ensure no further radio interference will occur. Always remove Batteries from transmitter when not in use. Do not dispose batteries in fire. Leakage, explosion and personal injury may occur. Do not attempt jumps or tricks with this vehicle. Do not attempt to remove internal battery. Do not use included USB cord for anything other than its intended purpose. Always keep USB cord stored when not in use. Adult supervision recommended. PROPER USE, PRECAUTIONS & CARE F.C.C. CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. ie OWNERS MANUAL Please read and understand all precautions prior to use. Thank you for choosing a premium New Bright product. USA & Canada 30-Day Limited Warranty New Bright Industries warrants to the original purchaser that this product will be free of defects in materials and workmanship for thirty (30) days from the date of purchase. In the event of such defect within the warranty period, New Bright will repair or replace the product at our sole discretion. This warranty does not cover damage resulting from unauthorized modifications, accident, misuse or abuse. Should your item have a defect covered under this warranty, first call the toll free number listed below. Most problems can be resolved in this manner. If necessary, you will be issued a Return Authorization (RA) number and instructions on how to obtain a Product Retum Form. The Product Return Form is to be used when returning a product to us (postage pre-paid and insured by the consumer). When retuming a defective product, please package the product, the Product Return Form and a copy of the dated sales receipt as proof of purchase. Be sure to mark the RA number on the Product Return Form. tf the product is returned without a dated sales receipt, it will be excluded from coverage under this warranty. Please allow 4 to 6 weeks for delivery of repaired or replacement vehicles (depending on your location). New Bright Industries liability for defects in materials and workmanship under this warranty shall be limited to repair or replacement at our sole discretion. In no event shall we be responsible for incidental, consequential or contingent damages (except in those states that do not allow this exclusion or limitation). Valid only in the USA & Canada. Contact New Bright Industries Customer Service Toll Free at:

1-877-NBI-TOYS

(1-877-624-8697) eg Me Monday through Friday, 8:00 AM to 5:00 PMEastemTime *. G| 8200 Eny Ins.

# a? q% 4S U.S. Toy Sales and Marketing Co. Inc. 30260 Oak Creek Drive 2nd Floor Wixom MI 48393 i B77-624-8697 0m ee enn om http:/www.newbright.com/ (227 &

(oem Fp) |

ee REF U02816.10400202 TRANSMITTER BATTERY INSTALLATION 1.Locate and remove the Battery Compartment Cover which is located on the back of the Transmitter. 2. Insert 2 AA size batteries. Make certain the positive (+) and negative

()markings on the batteries are in the same position as the positive (+) negative (-) markings inside the Battery Compartment. 3.Replace Battery Compartment Cover making certain that the Battery Compartment tab has snapped into the locked position. For Best Results:

1.Do not mix old and new batteries. 2.Do not mix alkaline, standard or rechargeable batteries. 3.Use alkaline batteries only. TRANSMITTER FUNCTIONS & HOW TO DRIVE This transmitter is equipped with 2.4GHz technology which allows up to 6 vehicles to be used at the same time. ;

To sync transmitter and vehicle, follow these steps:

1. Install batteries in Transmitter. 2. Turn on Vehicle. -

Once the batteries are installed and the vehicle is tumed on, the Transmitter will sync automatically with the vehicle. SIDE-TO-SIDE SLIDING LEFT SLIDING RIGHT SLIDING Turn wheel to the left Turn wheel to the right to slide left. a to slide right. FORWARD & REVERSE REVERSE DRIVING

| DRIVING Push forward on the trigger for Reverse Driving. FORWARD DRIVING Pull back on the trigger for Forward Driving. DIAGONAL SLIDING Turn the wheel while driving forward or reverse for diagonal sliding action. VEHICLE FUNCTIONS Charging Cord Charging ON/OFF Switch USB Compartment Cover Status Light Charging Port CHARGING INSTRUCTIONS Operation:

1.Move switch on bottom of vehicle to the OFF position. 2.Locate USB Charging port on underside of vehicle. 3.Open Storage Compartment cover. 4.Remove USB cable from the Storage Compartment. (Use care when extending cord as it is attached to inside internal battery). Cord can be plugged into any computer or USB outlet brick (not included). 5.The charging status light on the vehicle will turn on. 6. When charging is completed, in approximately 60 minutes, the charging status light will turn off. Return cord and secure storage lid before operating the vehicle.

FCC CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). 4 Operation is subject to the following two conditions: (1) This device may not cause Zo. interference; and (2) This device must accept any interference, including interference that R may cause undesired operation of the device. Couisinrtors Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux NEW BRIGHT CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L exploitation est autorise aux deux conditions suivantes : (1) Lappareil ne doit pas produire de brouillage; (2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. L948177021/JN216-14

ee et oe FCC ID:G6D1820UB_ New Brigm ~

Made in China This device complies with part 15 ofthe FCC Rules. Operation is subject tothe following two conditions:

(1) this device may not cause harmful Interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

VAS Yd lor HATE AKL |Z INEW{BRIGH TYINDUSTRIALTCOMLTDS New Bright Building, 11 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong. Tel: (852) 2798 1188 Fax: (852) 2795 3665 Date: 2019/3/29 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). -

In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use,our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

g) h) j) k) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Company Name: New Bright Industrial Co Ltd Contact Name: Eric Kwok Title of Person : Quality Manager Address: New Bright Building 11 Sheung Yuet Road, Kowloon Bay, Kowloon Hong Kong

Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:Request for Confidentiality FCC ID: G6D1820UB To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: New Bright Industrial Co., Ltd. Contact Name: Eric Kwok Title of PersonQuality Manager Address: New Bright Building 11 Sheung Yuet Road, Kowloon Bay, Kowloon Hongkong Date: 2020/4/8