FCC ID: G6D61429U1 TOY Receiver

CONTENTS Component Checklist

(1) RIC Vehicle With USB Cord

(2) AA Batteries App Download Additional features and functions are available and require the user to download and install the App Driver app onto a smart device to access. No charge to download. Data rates may apply. Apple Users:

Search New Bright App Driver in the App Store; Install. Android Users:

Search New Bright App Driver in Android Market or Google Play; Install. App Set Up 1. Install app to device. 2. Make certain the vehicle is fully charged (See charging instructions in Recharging the Vehicle). 3. Move ON/OFF switch to the ON position (See Vehicle Features for Switch location). Vehicle lights will turn on. 4. Launch the App Driver app on your smart device. 5.When launching, the app will ask to enable a connection with your device. Select yes to continue to use the app. This allows the app and your device to communicate with the vehicle. (If a proper connection has not been made, you will be prompted to repeat steps 2-4). 6. The vehicle and app are now communicating. 7. After a connection is established, you will be notified that the control range when using the app is limited. Use the included joystick controller when longer range is needed. The App features 4 ways to control your vehicle:

1. Select Drive Mode and choose Touch to control your vehicle using the touch screen or select Tilt* to control your vehicle using the gyroscope sensor in your device. Music, sound and light controls are also available. See instructions in Using the App. 2. Selecting Draw Mode allows you to draw a path and have the vehicle travel along that path. Music, sound and light controls are also available. See instructions in Using the App. 3. Selecting Code Mode allows you to program each segment of the vehicle's path adding sounds, music, and controlling the lights along the way. See instructions in Using the App.

*Tilt Mode Setup:

1. After selecting Tilt Mode you will be prompted to set the desired Neutral or Stop position. When your device is held at this position, the car will not move. Placing the device on a flat surface is NOT recommended for this mode. Exit Tilt Mode and start again to recalibrate. 2. Remember to exit Tilt Mode or close the app when finished or the vehicle may continue to be controlled by the movement of your device. a OlaAL=we 141-10) Below is the App Home Screen. Start by Selecting the Vehicle you have. When the image of your vehicle is displayed you can then select a mode from the 3 mode options on the left. Selected Vehicle 7 Tap to open. Ea sede App comes 4 pre-loaded with 2 Ca : b Sele ones. PT eg V up to 6 songs from a mesic Une Note: Default songs can be temporarily replaced by user music but can not Choose Vehicle ashes. Tap left & right arrows or swipe image to scroll jh vehicle options. Drive Mode Drive Mode allows you to use your device to control the vehicle by Touch or by Tilt. Mode, Sound, Light and Music options are available. Refer to the More Info section for details on these options. Speedometer Displays vehicle speed Sound ON/OFF

(not actual speed). Tap to turn sound on and off. Horn Tap to honk horn. Song Select Mode Select through Tap to toggle between Peles songs 7 Controls Back to Home Screen Touch and Tilt Mode. Light Tap lights ON/OFF. Gbwrindicates lights are ON. Fuel Meter Displays vehicle battery life. Left/Right Steering (Touch Mode) Forward/Reverse Drive (Touch Mode) Press and slide finger left to turn left. Press and slide finger upwards to drive Forward. Press and slide finger right to turn right. Press and slide finger downward for Reverse Drive. Release to stop turning. Release to Stop. Left/Right-Steering (Tilt Mode) Forward/Reverse Drive (Tilt Mode) Rotate device left to turn left. Tilt device forward (away from you)to drive Forward. Rotate device right to turn right. Tilt device back (towards you) to drive in Reverse. Hold device straight and level to stop turning. Hold device in the Neutral (N) starting position to Stop Driving. USING the APP Draw Mode Draw Path Mode allows you to use your finger to draw any path on the screen and the vehicle will drive that path. Speed, Lights, Music, Save and Load options are also available. Refer to the More Info section for details on these options. Pause "Back to Home Screen Stops vehicle. Tap Play to continue. Clear Path Save Path . Clears the canvas. Saves Current Path. a Le previous!

saved path. :

Play Start driving or Vehicle Speed resume driving the Tap to select current path. speed. Glow indicates Sound Select current speed. Tap for Options Light Controls Tap for Options Fuel Meter Displays vehicle battery life. Song Select Home Tap for Options. Takes user to Tap desired song Home screen. to begin playing. Canvas Tap again to stop. Drag your finger over the canvas to produce a path the vehicle will follow. More Info Individual menu options are explained below in-depth. Sound Select Light Controls Tapping Sound Select Tapping Light Controls opens opens the Sound the Lights Options menu. Options menu. Tap to choose one of 6 Tap to choose one of options, such as Bright Lights, 6 sounds: Engine Rev, Dim Lights, Left Turn Signal, Accelerate, Hard Stop, Right Turn Signal, Slow loop on repeat. Gear Shift, Tire Squeal Flashing, or Fast Flashing. Tap again to stop or Horn. song playback. Load Path opens the Song Options menu. 6 songs that will 3 ferred cemen PD ICPIS ae PU PFSY.. I Confirm Name & Save, Path saves as current date by default. Tap text box to edit with custom name. Delete saved path. Saved paths appear here. Tap path name to load path. Tapping Song Select Tap to choose one of USING the APP Code Mode Pause Stops vehicle. Tap Play to continue. Play Start driving or resume driving the current path. Directions Tap for Directional Options Sound Select Tap for Options Light Controls Tap for Options Song Select Tap for Options Add Sounds by opening the Sound Options Menu and dragging a sound to your desired location in the Sound input Field. To move an item to a different location, tap and hold for 2 seconds, then drag to desired location. To remove an item, tap and hold, then drag it off of the canvas. Code Path Mode allows you to select a sequence of directions that the vehicle will follow. Mode, Speed, Lights, Music, Save and Load options are available. Refer to the More Info section for details on these options. Below is an example of a coded path. To code a path, tap the Directions Icon to open the Directional Options Menu. Tap or drag and drop desired directions in the Directional Input Field. Choose from the following directions:

Open the Light Control Menu and drag the desired option into the Light Input Field to adjust the lights. Load Path Loads previously saved path. Back to Home Screen Clear Path Save Path Clears the canvas. Saves Current Path. Vehicle Speed Tap to select speed. Glow indicates current speed. Fuel Meter Displays vehicle battery life. Prec) CST e a) Home Takes user to Home screen. Light Input Field Field Sound Input _Directional Input Field Party Pee Reverse Left Right . Circle Drive A Turn >| Tum lum Turn Battery Installation 1. Flip smart phone holder up to reveal battery compartment. 2. Press and slide in the direction of the arrow open battery compartment cover. 3. Insert 2 AA size batteries. Make sure the positive (+) and negative

(}) markings on the batteries match the _ markings inside the Battery Compartment. 4. Replace the Battery Compartment Cover making certain that the Compartment tab has snapped into the locked position. Note: When replacing Transmitter batteries:

+ Do not mix old and new batteries. Do not mix alkaline, standard or rechargeable batteries. Use alkaline batteries only TRANSMITTER Features and Functions Light Press once to turn on light. Press again to tum off. Engine lights alway on. This transmitter is equipped with 2.4GHz technology which allows up to 6 vehicles to be raced at the same time. Once transmitter batteries have been correctly installed and vehicle ON/OFF Switch is in the ON position, the transmitter will automatically sync with the vehicle. Smart Phone Holder Locate the Smart Phone Holder at the back of the transmitter. Flip forward into the upright position. Next, gently pull up on the clamp while sliding phone in. Release clamp when phone is in place. VEHICLE Features and Funtions ON/OFF Switch Status Light

* If vehicle pulls to the left or right during forward driving the Wheel Alignment may need to be adjusted. The Wheel Alignment Dial is located on bottom of chassis between the front wheels. Removing Demo Wire This vehicle is shipped with a demo wire which runs from the vehicle battery compartment. The wire is for package demonstration only and should be removed and discarded as shown here. fol Grasp and pull firmly to remove demo wire. Pull in a straight, outward direction. Remove and discard the demo wire which runs from the vehicle. BATTERY I) PROPER use USB Smart Charge Technology Precautions & Care This product is equipped with USB Smart Charge Technology. The built-in smart chip can recognize the power output level of your chosen USB charging device. Charge times will vary between charging devices. Charging from a wall outlet with a USB adapter may be faster than charging from a USB port on a computer. Using Advanced USB Power Delivery, the smart chip will charge the vehicles internal battery at the fastest speed allowed by your charging device. Charging the Vehicle This vehicle is equipped with an internal Lithium-ion battery that is recharged via USB. ON/OFF Switch must be in the OFF position prior to charging. 1. Locate the ON/OFF switch and USB cord on the under-side of the vehicle. 2. Turn the ON/OFF switch to the OFF position. 3. Slide open Storage Compartment cover. 4. Remove USB cable from the Storage Compartment. (Use care when extending cord as it is attached to inside internal battery). Cord can be plugged into any os computer or USB outlet adapter (not included). a

5. While charging, the LED under the vehicle will be on. Once fully charged the LED Wipe body witha Do not use iearieais will turn off. Charging is completed in approximately 1 - 1.5 hours depending on the type of charging device you use. Return cord and secure storage lid before soft rag or tact cloth. or water to clean. operating the vehicle. UPPORT Trouble Shooting & Support Problem - Vehicle does not move or moves slowly.

~- Make certain there are fresh batteries in the transmitter and that they have been installed in the correct position.

- Are the (+) and (-) markings on the batteries in the same position as the

(+) and () markings in the Transmitter Battery Compartment?

- Are the metal contact tabs touching, rusty or dirty in the transmitter?

- Has the vehicle been fully charged?

- Make certain that the vehicle ON/OFF switch is in the ON position. Problem - Vehicle moves by itself or exhibits reduced range from the transmitter.

- Make certain there are no outside radio interference in your area. The best way to test this is to take the vehicle as far away from radio towers, electrical lines or tall buildings as possible to ensure no further radio interference will occur. Always remove Batteries from transmitter when not in use. Do not dispose batteries in fire. Leakage, explosion and personal injury may occur. Do not attempt jumps or tricks with this vehicle. Do not attempt to remove internal battery. Do not use included USB cord for anything other than its intended purpose. Always keep USB cord stored when not in use. Adult supervision recommended. FCC CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct. the interference by one or more of the folowing measures:

~ Reorient or relocate the receiving antenna.

~ Increase the separation between the equipment and receiver.

~ Connect the equipment into an outlet on a circuit fferent from that to which the receiver is connected.

= Consult the dealer or an experienced radio/TV technician for help. NEW (/ BRIGHT. OWNERS MANUAL Please read and understand all precautions prior to use. Thank you for choosing a premium New Bright product. USA & Canada 30-Day Limited Warranty New Bright Industries warrants to the original purchaser that this product will be free of defects in materials and workmanship for thirty (30) days from the date of purchase. In the event of such defect within the warranty period, New Bright will repair or replace the product at our sole discretion. This warranty does not cover damage resulting from unauthorized modifications, accident, misuse or abuse. Should your item have a defect covered under this warranty, first call the toll free number listed below. Most problems can be resolved in this manner. If necessary, you will be issued a Return Authorization number (RA) and instructions on how to obtain a Product Retum Form. The Product Return Form is to be used when returning a product to us (postage pre-paid and insured by the consumer). When returning a defective product, please package the product, the Product Return Form and a copy of the dated sales receipt as proof of purchase. Be sure to mark the RA number on the Product Return

- Form. If the product is returned without a dated sales receipt, it will be excluded from coverage under this warranty. Please allow 4 to 6 weeks for delivery of repaired or replacement vehicles (depending on your location). -

New Bright Industries liability for defects in materials and workmanship under this warranty shall be limited to repair or replacement at our sole discretion. In no event shall we be responsible for incidental, consequential or contingent damages (except in those states that do not allow this exclusion or limitation). Valid only in the USA & Canada. Contact New Bright Industries Customer Service Toll Free at:

1-877-NBETOYS

(1-877-624-8697) Monday through Friday, 8:00 AM to 5:00 PM Eastern Time U.S. Toy Sales and Marketing Co. Inc. 30260 Oak Creek Drive 2nd Floor Wixom Mi 48393 1-877-624-8697 httpy/www.newbright.com/

REF-U92416 JN129-21

orem ree arr leal REN gurins Made in China eR eR eco TTS Aa ma RSet

(Q) this device may not cause harmfulinterterence, and GORI ea ete cae re ect cee including interference that may cause undesired operation.

Date: 02/04/2021 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) c) d) e) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) g) h) i) j) use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Company Name: New Bright Industrial Co Ltd Contact Name: Eric Kwok Title of PersonQuality Manager Address: New Bright Bldg 11 Sheung Yuet Road, Kowloon Bay Kowloon, Hong Kong

Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: G6D61429U1 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: New Bright Industrial Co Ltd Contact Name: Eric Kwok Title of PersonQuality Manager Address: New Bright Bldg 11 Sheung Yuet Road, Kowloon Bay Kowloon, Hong Kong Date: 03/23/2021