FCC ID: G6D31HBRRXS TOY Transmitter

BATTERY INSTALLATIONS AND OPERATING INSTRUCTIONS nz This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Battery Installa'

1. Remove battery compartment covers on vehicle and transmitter by removing screw and pulling in the ection shown by the arrow. 2. Install AA batteries in the battery compartments with positive (+) and negative () ends matching the compartment markings. 3. Replace the battery covers. Secure with screw. 4, When vehicle is turned on, the transmitter will automatically sync with the vehicle. 5. The vehicle is equipped with 2.4GHz technology which allows up to 6 vehicles to be raced at the NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses same time. and can radiate radio frequency energy and, if not installed Operation: and used in accordance with the instructions, may cause 1. START: Move switch on bottom of vehicle to the ON harmful interference to radio communications. However, position. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

2. FORWARD/REVERSE: Push forward/reverse joystick up to move vehicle forward and down for reverse.

| 3, LEFT/RIGHT STEERING: Push left/right joystick left to turn vehicle left or right to turn right. - Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circui different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Steering Trim:

If the vehicle veers to the left or right, adjust steering trim -

on underside of vehicle until the desire alignment is reached. =

Battery Requirements:

Vehicle: 3 AA Batteries Transmitter: 2 AA Batteries 1-877-NBI-TOYS

(1-877-624-8697) Monday through Friday, 8:00 AM to 5:00 PM Eastern Time U.S. Toy Sales and Marketing Co. Inc. 30260 Oak Creek Drive 2nd Floor Wixom MI 48393 1-877-624-8697 http:/www.newbright.com/

For Best Results:

1. Do not old and new batteries. 2. Do not alkaline, standard or rechargeable batteries. 3. Use alkaline batteries only. F.C.C. CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Contact New Bright Industries Customer Service Toll Free at:

BATTERY INSTALLATIONS AND OPERATING INSTRUCTIONS Battery Installation:

1. Remove battery compartment covers on vehicle and transmitter by removing screw and pulling in the direction shown by the arrow. 2. Install AA batteries in the battery compartments with positive (+) and negative () ends matching the compartment markings. 3. Replace the battery covers. Secure with screw. 4. When vehicle is turned on, the transmitter will automatically sync with the vehicle. 5. The vehicle is equipped with 2.4GHz technology which allows up to 6 vehicles to be raced at the same time. Operation:

1. START: Move switch on bottom of vehicle to the ON position. 2, FORWARD/REVERSE: Push forward/reverse joystick up to move vehicle forward and down for reverse.

/3, LEFT/RIGHT STEERING: Push left/right joystick left to turn vehicle left or right to turn right. Steering Tri If the vehicle veers to the left or right, adjust steering trim on underside of vehicle until the desire alignment is reached. Battery Requirements:

Vehicle: 3 AA Batteries Transmitter: 2 AA Batteries For Best Results:

1. Do not mix old and new batteries. 2. Do not mix alkaline, standard or rechargeable batteries. 3. Use alkaline batteries only. F.C.C. CAUTIO!

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condition:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE:

This equipment has been tested and found to comply the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not install and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user encouraged to try to correct the interference by one or more of the following measures:

fh

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Contact New Bright Industries Customer Service Toll Free at:

1-877-NBI-TOYS

(1-877-624-8697) Monday through Friday, 8:00 AM to 5:00 PM Eastern Time U.S. Toy Sales and Marketing Co. Inc. 30260 Oak Creek Drive 2nd Floor Wixom MI 48393 1-877-624-8697 http://www.newbright.com/

BATTERY INSTALLATIONS AND OPERATING INSTRUCTIONS Battery Installation:

1. Remove battery compartment covers on vehicle and transmitter by removing screw and pulling in the direction shown by the arrow. 2. Install AA batteries in the battery compartments with posi (+) and negative () ends matching the compartment markings. 3. Replace the battery covers. Secure with screw. 4. When vehicle is turned on, the transmitter will automatically sync with the vehicle. 5. The vehicle is equipped with 2.4GHz technology which allows up to 6 vehicles to be raced at the same time. 6 Operation: . 1. START: Move switch on bottom of vehicle to the ON position. 2. FORWARD/REVERSE: Push forward/reverse joystick up to move vehicle forward and down for reverse. 3. TURBO DRIVE: Press and hold Turbo Button for faster speed while driving forward. Release button to return to normal drive speed. 4. LEFT/RIGHT STEERING: Push left/right joystick left to turn vehicle left or right to turn right. Steering Trim:

If the vehicle veers to the left or right, adjust steering trim on underside of vehicle until the desire alignment is reached. Battery Requirements:

Vehicle: 3 AA Batteries Transmitter: 2 AA Batteries For Best Results:

1. Do not mix old and new batteries. 2. Do not mix alkaline, standard or rechargeable batteries. 3. Use alkaline batteries only. F.C.C. CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Turbo Button eres ae This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These |i reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Contact New Bright Indust 1-877-NBI-TOYS

(1-877-624-8697) Monday through Friday, 8:00 AM to 5:00 PM Eastern Time U.S. Toy Sales and Marketing Co. Inc. 30260 Oak Creek Drive 2nd Floor Wixom MI 48393 1-877-624-8697 http://www.newbright.com/

s Customer Service Toll Free at:

FCC CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). 4 Operation is subject to the following two conditions: (1) This device may not cause Zo. interference; and (2) This device must accept any interference, including interference that R may cause undesired operation of the device. Couisinrtors Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux NEW BRIGHT CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L exploitation est autorise aux deux conditions suivantes : (1) Lappareil ne doit pas produire de brouillage; (2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. L948177021/JN216-14

Date: 2/25/2021 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) c) d) e) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) g) h) i) j) use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Company Name: New Bright Industrial Co., Ltd. Contact Name: Eric Kwok Title of Person: Quality Manager Address: New Bright Building 11 Sheung Yuet Road, Kowloon Bay, Kowloon Hongkong

Confirmation Letter

We, NEW BRIGHT INDUSTRIAL CO., LTD

The product: TOY Transmitter

And model No.: 31HBRRXS

31HBRRXS have 3 variants (variant 1, variant 2, variant 3), they have the same technical construction

including circuit diagram, PCB Layout, components and component layout, all electrical construction

and mechanical construction. The difference lies only the plastic appearance and variant 1 have one

more key, all these changes do not degrade the unwanted emissions of the product.

Company Name: New Bright Industrial Co., Ltd.

Contact Name: Eric Kwok

Title of Person：Quality Manager

Address: New Bright Building 11 Sheung Yuet Road, Kowloon Bay, Kowloon Hongkong

Date: 7/6/2021

Federal Communications Commission

7435 Oakland Mills Road

Columbia MD 21046

Subject:

Request for Confidentiality

FCC ID:

G6D31HBRRXS

To Whom It May Concern:

Schematic Diagram

Block Diagram

Theory of Operation

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §

§

0.457, 0.459), we are requesting the Commission to withhold the following attachments as

confidential document from public disclosure indefinitely.

Above mentioned document contains detailed system and equipment description are considered

as proprietary information in operation of the equipment. The public disclosure of above

documents might be harmful to our company and would give competitor an unfair advantage in

the market.

It is our understanding that all measurement test reports, FCC ID label format and correspondent

during certification review process cannot be granted as confidential documents and those

information will be available for public review once the grant of equipment authorization is

issued.

Best Regards

Company Name: New Bright Industrial Co., Ltd.

Contact Name: Eric Kwok

Title of Person: Quality Manager

Address: New Bright Building 11 Sheung Yuet Road, Kowloon Bay, Kowloon Hongkong

Date: 7/6/2021