FCC ID: G6D3720HH2 TOY Transmitter

WHATS INCLUDED Component Checklist

(1) USB Charging Cord

(1) Rechargeable Battery Soft Pack TRANSMITTER Battery Installation 1. To open battery compartment cover on transmitter, slide in the direction indicated by the arrow. 2. Insert 2 AA size batteries. Make sure the positive (+) and negative (-) markings on the batteries match up to the ones inside the Battery Compartment. 3. Replace the Battery Compartment Cover making certain that the Compartment tab has snapped into the locked position. Note: When replacing Transmitter batteries:

Do not mix old and new batteries. Do not mix alkaline, standard or rechargeable batteries. Use alkaline batteries only. Syncing This transmitter is equipped with 2.4GHz technology which allows up to 6 vehicles to be used at the same time. :

Before first use and after any time the batteries are replaced, the transmitter must be paired to the vehicle. To sync transmitter and vehicle, follow the steps below:

1. Correctly install batteries in the transmitter. 2. Place vehicle upside down, and turn Vehicle ON/OFF switch to the ON position. The vehicle is only in sync mode for 30 seconds. 3. Immediately press and hold the Forward/Reverse joystick on the transmitter. Keep holding until wheels move (up to 30 sec.). TRANSMITTER Functions When vehicle is powered OX, headlights and side lights wil flash. When vehicle isin mation the lights will glow. FORWARD DRIVING FLIPS Push BOTH joysticks forward Push both joysticks forward to begin for Forward Driving. Forward Driving, then quickly pull back bath joysticks to flip the vehicle over. REVERSE DRIVING Pull BOTH joysticks backward for Reverse Driving. RIGHT TURNING Push LEFT joystick forward to turn right while driving forward. Pull LEFT joystick back to turn right in reverse. LEFT TURNING Push RIGHT joystick forward to turn left while driving forward. Pull RIGHT joystick back to turn left in reverse. 360 SPINS - Clockwise Push joysticks as shown for Clockwise

* Spinning. 360 SPINS - Counter-Clockwise Push joysticks as shown for Counter-Clock-

wise Spinning. venice Features ON / OFF Switch A b Air Pump Nozzle

(Located on the outer sidewall of each tire) ime p \

7 VY)

) BY Inflating the Tires To properly perform flips, ensure the tires are fully inflated. A properly inflated tire should be firm, but not hard. 1. Locate the Air Pump Nozzle on the sidewall of the tires. 2. Insert the pin of the Air Pump into the tire nozzle. 3. Pull the Air Pump handle out fully, then push it back in. 4, Repeat until tires are fully inflated and firm to the touch. 5. Avoid overfilling tires. If tires are over-inflated, to slightly deflate the tire. VEHICLE PROPER use Installing Vehicle Battery Charging This vehicle is equipped with a removable Lithium-Ion battery soft pack that is recharged via USB. Vehicle must be switched OFF prior to charging. 1. Locate the Battery Compartment Cover Screw located on the top side of vehicle (shown in Vehicle Features Section). 2. Remove screw and slide open compartment cover. Place screw in a safe place. 3. Locate the Battery and Vehicle Connectors, shown above. Grab hold of the plastic connector. Using a fingernail, pull back the locking tab and pull to separate the connectors. Do not grab and pull by the wires. Remove the Battery Pack. 4, Connect the supplied USB Charging Cord (shown above) by pressing the Battery and USB connectors together until the locking tab clicks in place. 5. Plug USB into any powered 5V DC USB port. Charging is completed in approximately 1.5-2 hours

(when charging from a computer). 6. After charging is complete, reconnect the Battery and Vehicle and store the USB cord in a safe place. Replace compartment cover and secure with screw. Precautions and Care CAUTION!

Do not recharge Battery if vehicle is hot or warm to the touch. Allow Battery to cool before recharging. Recharging a hot or warm Battery will shorten the life of the unit. Do not recharge the Battery if it appears to be damaged or leaking. Do not use included USB Cord for anything other than the intended purpose. Do not dispose batteries in fire. Leakage, explosion and personal injury may occur. Do not attempt to disassemble Battery soft pack. Always remove Batteries from transmitter when not in use. Only an adult should charge Batteries. SUPPORT Trouble Shooting Problem - Vehicle does not move or moves slowly.

- Has the rechargeable Internal Battery been fully charged?

-- Make certain there are fresh alkaline batteries in the transmitter and that they have been installed in the correct position. _ 7 Are the (+) and (-) markings on the alkaline batteries in the same position as the (+) and (-) markings in the Transmitter Battery Compartment?

- Make certain that the vehicle ON/OFF switch is in the ON position. Problem - Vehicle does not flip over.

- Check that the tires are fully inflated. Inflate until firm. Problem - Vehicle moves by itself or exhibits reduced range from the transmitter.

- Make certain there is no outside radio interference in your area. The best way to test this is to take the vehicle as far away from radio towers, electrical lines or tall buildings as possible to ensure no further radio interference will occur. FCC CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two col ns:

(1) this device may not cause harmful interference, and (2) this devic must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

~ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-,Consutt the dealer or an experienced radio/TV technician for help. OWNERS MANUAL

.. Please read and understand all precautions prior to use.

- ONE ta Annee L el Thank you for choosing a premium New Bright product. USA & Canada 30-Day Limited Warranty New Bright Industries warrants to the oilginat purchaser that this product will be free of defects in materials and workmanship for thirty (30) days from the date of purchase. In the event of such defect within the warranty period, New Bright will repair or replace the product at our sole discretion. This warranty does not cover damage resulting from unauthorized modifications, accident, misuse or abuse. Should your item have a defect covered under this warranty, first call the toll free number listed below. Most problems can be resolved in this manner. If necessary, you will be issued a Return Authorization (RA) number and instructions on how to obtain a Product Return Form, The Product Return Form is to be used when returning a product to us (postage pre-paid and insured by the consumer). When returning a defective product, pfGase package the product, the Product Return Form and a copy of the dated sales receipt as proof of purchase. Be sure to mark the RA number on the Product Return Form. If the product is returned without a dated sales receipt, it will be excluded from coverage under this warranty. Please allow 4 to 6 weeks for delivery of repaired or replacement vehicles (depending on your location). New Bright industries Uability for defects in materials and workmanship under this warranty shall be limited to repair or replacement at our sole discretion. Inno event shall we be responsible for incidental, consequential or contingent damages (except in those states that do not allow this exclusion or limitation). Valid only in the USA & Canada, Contact New Bright Industries Customer Service Toll Free at:

1-877-NBI-TOYS

(1-877-624-8697) Monday through Friday, 8:00 AM to 5:00 PM Eastern Time REF-1663U JNO13-24

FCC CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). 4 Operation is subject to the following two conditions: (1) This device may not cause Zo. interference; and (2) This device must accept any interference, including interference that R may cause undesired operation of the device. Couisinrtors Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux NEW BRIGHT CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L exploitation est autorise aux deux conditions suivantes : (1) Lappareil ne doit pas produire de brouillage; (2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. L948177021/JN216-14

Date: 02/04/2021 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) c) d) e) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) g) h) i) j) use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Company Name: New Bright Industrial Co Ltd Contact Name: Eric Kwok Title of PersonQuality Manager Address: New Bright Bldg 11 Sheung Yuet Road, Kowloon Bay Kowloon, Hong Kong

Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 2.911 (d)(7) FCC US Agent Letter of Attestation Date: 1/8/2024 Grantee Code: G6D Grantee FRN: 0006258263 To whom it may concern:

FCC US Agent Agent Company Name:US Toy Sales & Marketing Inc FCC FRN: 0033562331 Agent Contact Name: Dawn Hunholz Agent US Address: 30260 Oak Creek Dr 2nd Floor Wixom, MI 48393 United States Agent Email Address: dhunholz@newbright.net This letter is to confirm that we have accepted the responsibility to act as US Agent on behalf of New Bright Industrial Co.,Ltd (the applicant). We are aware of the requirements and responsibilities of the applicants agent for service of process as outlined in the FCC section 2.911(d)(7) and Report and Order FCC 22-84 paragraph 63. Sincerely, Authorized Agent Contact Person NameDawn M Hunholz Agent contact Job TitlePresident Agent Company nameUS Toy Sales & Marketing Inc

CFR 47 2.911 (d)(5) Attestation Date:12-15-2023 FCC ID: G6D3720HH2 Grantee FRN:0006258263 To: Federal Communication Commission 7435 Oakland Mills Road Columbia, MD 21046 USA 1. New Bright Industrial Co.,Ltd (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2. New Bright Industrial Co.,Ltd (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Name: Eric Kwok Job Title: Quality Manager Company Name: New Bright Industrial Co.,Ltd

Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

Request for Confidentiality FCC ID:

G6D3720HH2 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Bom list Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: New Bright Industrial Co., Ltd. Contact Name: Eric Kwok Title of PersonQuality Manager Address: New Bright Building 11 Sheung Yuet Road, Kowloon Bay, Kowloon Hongkong Date: 12/15/2023

CFR 47 2.911 (d)(7) Agent Designation Attestation Date: 12-12-2023 FCC ID: G6D3720HH2 Grantee FRN:0006258263 7435 Oakland Mills Road Columbia, MD 21046 USA To: Federal Communications Commission New Bright Industrial Co Ltd (the applicant) as required by section 2.911(d)(7), designates the following agent, located in the United States, for purposes of acting as the applicants agent for service of process. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the agent information changes. U. S. Agent Information:

Dawn Hunholz US Toy Sales & Marketing Inc FCC FRN: 0033562331 30260 Oak Creek Dr 2nd Floor Wixom, MI 48393 United States dhunholz@newbright.net Sincerely yours, Name:

Eric Kwok Job Title:

Quality Manager Company Name: New Bright Industrial Co Ltd