FCC ID: X4YNXG150 NexxtGate 150 High Power Access Point

Nexxt Solutions - NexxtGate150 Access Point Quick Installation Guide 1. Introduction Thank you for purchasing the Nexxt Solutions 2 .4 GHz High-Power Wireless-N Access Point NexxtGate150. If any of the following items are mismatched, missing or damaged, please contact the merchant from whom you purchased the unit for immediate replacement. 150Mbps wireless long-range access point 1 pc 1 pc Power adapter 1~

~~~~~

2 pcs ne wraps Passive PoE injector 1 pc 2 pcs each Screws and anchors Grounding screw 1 pc Quick installation guide 2. Product overview 2.1 Front view layout and connectors Please refer to the figure below to familiarize yourself with the access point's layout, features and connectors. 2 Nexxt Solutions - NexxtGate150 Access Point 1. Ground: Attach a copper wire here to establish a good earth ground and to provide the proper surge and lightning protection. 2. SMAIQc This is a RP- SMA jack to connect an optional external antenna 3. LAN: This is a 10/100Mbps LAN port 4. LAN/WAN/POE: This port provides Power over an Ethernet connection through the injector module, and it works interchangeably as a WAN port in router mode end as a LAN port in AP mode. 5. Cable access hole cut-outs. 2.2 Injector overview LAN/WAN: 1 OOMbps Ethernet port. PDE: Power over Ethernet port. Reset: Press it for 8-10 seconds to restore device to factory its default settings. Power: DC input jack. 3 Nexxt Solutions - NexxtGate150 Access Point 2.3 Rear view LED status indicator panel Slip resistant pole/well mounting brackets LED PWR Status Solid orange light Solid orange light WAN/LAN Blinking orange light LAN Solid orange light Blinking orange light WLAN Orange Pink Red Description The device is connected to the power source An Ethernet cable is connected Data is being transmitted through that port An Ethernet cable is connected Data is being transmitted through that port Maximum power is used to broadcast the wireless signal Medium power is used to broadcast the wireless signal Low power is used to broadcast the wireless signal 4 Nexxt Solutions - NexxtGate150 Access Point 2.4 Checking the LEDs Upon powering on your access point. verify that the PWR and WlAN LEDs light up orange. 3. Location of the access point Before making any hardware connections, find a suitable location to place the access point. The best spot is usually at the center of the wireless network, with unobstructed line-of-sight to all wireless clients operating in the coverage area. Also consider that the higher the antenna is placed, the better the device can perform. Do not forget to make sure that the structure or pole you use to install the device is stable and properly secured. 1. If setting up the device in an indoor installation, use the keyholes on the brackets to mark the location on the wall where the access point is to be mounted. 2. Drill the holes and then drive the supplied anchors

[if required] and screws into the wall . Leave the head of the screw slighgtly above the surface to hang the access point from the keyholes on the back. wall 5 Nexxt Solutions - NexxtGate150 Access Point 3. If setting up the device in an outdoor location, thread the tie wraps trough the grooves underneath the brackets. Then attach the device firmly to the pole. The connection will be similar to the figure below, once the above steps have been successfully completed . pole 4. Herdwere installation 1. Slide the bottom cover of the unit down to expose the ports. 2. In order to integrate your new wireless access point into your installation, start by plugging one end of an Ethernet cable to the PoE port of the supplied injector module, and the other end of the cable to the LAN/

WAN/POE port on the access point. 3. Use a second Ethernet cable to make the connection between the LAN port of the PoE module and your computer. 4. Replace the cover by sliding it up it until it clicks in place. 5. Power the device by plugging the included AC power adapter to DC jack on the PoE unit, and the other end into a standard wall outlet. 6 Nexxt Solutions - Ne:xxtGate150 Access Point 5. Initial configuration Note: only a wired network connection can be used for the initial configuration of the access point. Since this this device operates in AP mode by default, the user needs to manually configure a static IP address for the PC. 1. To do so, click on Start> Control Panel> Network and Internet> Network and Sharing Center, followed by Change adapter settings. 2.After right-clicking on the Local Area Connection, select Properties. Local Area Connection Disable Status Diagnose Bridge Connections Create Shortcut Delete Rename Properties 7 Nexxt Solutions - NexxtGate150 Access Point 3.Select Internet Protocol Version 4 [TCP/1Pv4) and then go to Properties. You may also enable this option directly by double-<:licking on Internet Protocol Version 4 [TCP/1Pv4). Local Area Connectio n 2 Properties Networking ~S_h_a_;n~g~-------------~

Connect using:

rfj Reattek RTL8139/810xfamily fast Ethernet NIC Configure ... This connection uses the following items:

~ :.L Client for Microsoft Networks

~ maoS Packet Scheduler

~ ~File and Printer Sharing for Microsoft: Networks

~ ...... Internet Protocol Version 6 (TCP/1Pv6)

~ .... I Internet Protocol Version 4 (TCP/1Pv4) I

~ ...._ link-layer T apology Discovery Mapper VO Driver

~ ..... Link-Layer Topology Discovery Responder

~--ln_st_al_L. __ ] LUnmstall Description Properties Transmission Control Protocol/lntemetProtocoL The default wide area network protocol that provides communication across d iverse interconnected networks. OK 11 Cancel 4.0nce the next dialog box comes up, select Use the following IP address option. The following items will become available:

IP address: Enter 192. 168.0. XXX (whereby X is any number between 2-253). Subnet mask: Enter 255.255.255.0. 8 Nexxt Solutions - NexxtGate150 Access Point 5.Click OK twice to save your settings and complete the IP address configuration of the device. 5.1 Login 1.Start your WEB browser. Type http:/ /192.168.0.1 in the address field and press enter to continue. If) New Tab - Windows Internet Explorer u u

@.] http://192l68.0l/

2.A dialog box will prompt you to enter the User name and Password. By default, both are set to admin, in lowercase. Click login to complete this step. Login 3.Afterwards, you can assign a new password for security purposes without necessarily modifying the default user name. 4. If the login window fails to appear, it means that your Web-browser has been set to a proxy. Verify that your parameters and passwords are correct, before making another attempt. 9 Nexxt Solutions - NexxtGate150 Access Point 5.2.Quick setup wizard 1.After successfully logging in, click on the Quick setup tab. Three operation modes are provided in the access point to meet each user's needs. AP mode: this mode enables wireless devices to access a network using wi-fi, in an access point configuration. Universal repeater mode: choose this mode to enable users to share the internet as a WISP client router. Router mode: choose this mode to enable users to share internet via ADSL/Cable modem, in a wireless broadband router configuration. 2.For illustration purposes, we will walk you through the AP option, which is also the default mode of operation for the device. 3.After selecting AP mode, click Next to open the wireless configuration window, as illustrated below:

10 Nexxt Solutions - NexxtGate150 Access Point 4. Proceed to configure the basic wireless parameters including SSID, channel and security. SSID: enter a unique name to identify your wireless network. However, choose one that is easily remembered by network users. In this example, we are using Nexxt_XXXXXX as the SSID identifier [whereby the "X" represents the last six digits of the access point's MAC address). Channel: for optimal wireless performance, use the Auto default setting to let the device automatically scan a channel with the least interference for your wireless network to operate on, or you may manually select an unused channel from the drop-down list. Security mode (encryption algorithm): this option is disabled by default with no password assigned. However, we recommend selecting WPA/WPA2-

PSK and entering a passkey in order to properly secure your network. 5.Click Next to configure the wireless settings for the device. The device MUST operate on the same chan nel as the uplink AP for successful implementation of the feature. 6.Click on Complete to exit the Quick Setup wizard and reboot the access point. 11 Nexxt Solutions - NexxtGate1 50 Access Point 7. To do so, go to Tools > Reboot >Reboot. When the initialization process is complete, changes will take effect and the device will be ready to operate in AP mode. 8. Remove the LAN cable from your computer and the PoE module. Now, insert your internet cable into the port labeled LAN located in the PoE device. Note: at this point you need to set the computer back to obtain an IP address automatically. Refer to steps 1 through 4 under section 5, Initial configuration. Internet Protocol Version 4 (TCP/IPv4) Properties General l Alternate Configuration I You can get IP settings assigned automatically if your network supports this capability. otherwise, you need to ask your network administratorfortheappropriateIPsettings.

@Q.~~~-~~---~-~---~--~-~.9..~~-~-.. ~.~.t.~.~.~-~~-~.~.!.!'r!

~ U~thefollowingIPaddress:

IP address:

Sybnetmask:

Qefaultgateway:

@ OQtainDNSserver addressautomaticalty

~ U~thefollowingDNSserveraddresses E.referred DNSserver:

~ lternat:e DNSserver O vajidatesettingsuponexit 12 Nexxt Solutions - NexxtGate150 Access Point 9. The figure below illustrates the typical network topology in AP mode. . ...

:;;);:

'g D 'o

. ... a .. . . . . .

-

I 10. Refer to the manual later on for any customized settings such as security, encryption, network modes, antenna alignment and more. 13 Nexxt Solutions - NexxtGate150 Access Point FCC statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1 I This device may not cause harmful interference. and

(2) this device must accept any interference received , including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a par ticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 14 NelCJCt Solutions - NexxtGate150 Access Point FCC caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be ccrlocated or operating in conjunction with any other antenna or transmitter. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Radiation exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. FCCID:X4YNXG150 15

Project No.: 1411C285 Page 10 of 16 Project No.: 1411C285 Page 11 of 16 Project No.: 1411C285 Page 12 of 16 Project No.: 1411C285 Page 13 of 16 Project No.: 1411C285 Page 14 of 16 Project No.: 1411C285 Page 15 of 16 Project No.: 1411C285 Page 16 of 16

Project No.: 1411C285 Page 2 of 16 Project No.: 1411C285 Page 3 of 16 Project No.: 1411C285 Page 4 of 16 Project No.: 1411C285 Page 5 of 16 Project No.: 1411C285 Page 6 of 16 Project No.: 1411C285 Page 7 of 16 Project No.: 1411C285 Page 8 of 16 Project No.: 1411C285 Page 9 of 16

NEXXT Ce = ee ee Se =

NexxtGate 150 / High Power Access Point Made in China Model: AEOPLDR4U2 DOC Power: 12V>==1.5A IP Address: 192.168.0.1 LIser name: admin C Password: admin FCC ID: X4YNX<G150 SY =

This device complies with part 15 of the FCC Rules. va Operation is subject to the following two conditions: te

(1) This device may not cause harmful interference, and a

(=) this device must accept any interference received, including interference that may cause undesires operations.

NEXXT SOLUTIONS To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for confidentiality FCC ID: X4YNXG150 Dear FCC TCB:

1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

Schematic Block diagram Operational description Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. Sincerely, 2014-12-22

NEXXT SOLUTIONS Ad Hoc Mode Declaration We, the undersigning company Name: NEXXT SOLUTIONS Address: 3505 N.W 107TH AVE. City: MIAMI Country: United States Hereby confirm that the following products:

Product description: NexxtGate 150 | High Power Access Point Type designation: AEOPLDR4U2 Brand: NEXXT Doesnt have Ad Hoc Made function on non-US frequencies. In addition, the frequency selection feature is disabled by firmware for devices marketed to the US. For this product, only channels 1~11 will be used in USA. Country code selection is disabled.

FCC RF EXPOSURE REPORT FCC ID: X4YNXG150 Project Equipment Model Applicant Address 1411C285

: NexxtGate 150 High Power Access Point

: AEOPLDR4U2

: NEXXT SOLUTIONS

: 3505 N.W MIAMI, FL, 33178 According:

: FCC Guidelines for Human Exposure IEEE C95.1 B T L I N C . No.3, Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, China. TEL: +86-769-8318-3000 FAX: +86-769-8319-6000 MPE CALCULATION METHOD:

Calculation Method of RF Safety Distance:

where:

S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Table for Filed Antenna Ant. Brand Model Name N/A N/A 1 2 Tenda Q5091 Antenna Type Connector Gain(dBi) Note Internal Dipole N/A N/A 10.00 TX/RX 5.07 TX/RX Note: Antenna 1 and antenna 2 is optional. Only one antenna is used at a time. These two antennas can not transmit simultaneously. TEST RESULTS EUT Temperature Test Voltage :

Test Mode ExxtGate 150 High Power Access Point 25 AC 120V/60Hz TX B MODE_Ant 1 /CH01, CH06, CH11 Model Name :

Relative Humidity: 55 %

AEOPLDR4U2 Antenna Gain

(numeric) Peak Output Power (dBm) Peak Output Power (mW) Antenna Gain

(dBi) 10.00 10.00 10.00 10.0000 10.0000 10.0000 18.75 18.56 15.70 Power Density (S)

(mW/cm2) 0.14926238 74.9894 71.7794 0.14287307 37.1535 0.07395208 Limit of Power Density (S)

(mW/cm2) 1 1 1 Test Result Complies Complies Complies EUT Temperature Test Voltage :

Test Mode ExxtGate 150 High Power Access Point 25 AC 120V/60Hz TX G MODE_Ant 1/CH01, CH06, CH11 Model Name :

Relative Humidity: 55 %

AEOPLDR4U2 Antenna Gain

(numeric) Peak Output Power (dBm) Peak Output Power (mW) Antenna Gain

(dBi) 10.00 10.00 10.00 10.0000 10.0000 10.0000 22.60 25.30 20.50 Power Density (S)

(mW/cm2) 0.36220160 181.9701 338.8442 0.67445095 112.2018 0.22333170 Limit of Power Density (S)

(mW/cm2) 1 1 1 Test Result Complies Complies Complies EUT Temperature:

Test Voltage :

Test Mode :

ExxtGate 150 High Power Access Point 25 AC 120V/60Hz TX N-20M MODE_Ant 1 /CH01, CH06, CH11 Model Name :

Relative Humidity: 55 %

AEOPLDR4U2 Antenna Gain

(dBi) 10.00 10.00 10.00 Antenna Gain

(numeric) Peak Output Power (dBm) Peak Output Power (mW) 10.0000 10.0000 10.0000 19.10 23.00 19.60 81.2831 199.5262 0.39714616 91.2011 0.18153082 Power Density (S)

(mW/cm2) 0.16178951 Limit of Power Density (S)

(mW/cm2) 1 1 1 Test Result Complies Complies Complies ExxtGate 150 High Power Access Point 25 AC 120V/60Hz TX N-40M MODE_Ant 1/CH03, CH06, CH09 Model Name :

Relative Humidity: 55 %

AEOPLDR4U2 EUT Temperature:

Test Voltage :

Test Mode :

Antenna Gain

(numeric) Peak Output Power (dBm) Peak Output Power (mW) Antenna Gain

(dBi) 10.00 10.00 10.00 10.0000 10.0000 10.0000 19.80 21.10 16.90 Power Density (S)

(mW/cm2) 0.19008610 95.4993 128.8250 0.25641910 48.9779 0.09748782 Limit of Power Density (S)

(mW/cm2) 1 1 1 Test Result Complies Complies Complies Note:

1)Antenna 1 has the higher gain so it is recorded as the worst case. 2)The calculated distance is 20 cm.

RF_160, Issue 03 Declaration of Authorization We Name: NEXXT SOLUTIONS Address: 3505 N.W 107TH AVE. City: MIAMI Country: United States Declare that:

Name Representative of agent! Cathy Wang Agent Company name: BTL Inc. Address: No.3 Jinshagang 1st Road, Shixia, Dalang Town City: Dong Guan Country: China is authorized to apply for Certification of the following product(s), including the signing of the related documents such as 731 form(s):

Product description: NexxtGate 150 | High Power Access Point Type designation: AEOPLDR4U2 Trademark: NEXXT on our behalf. Date: 2014-12-22 City: MIAMI Name: Albert Mizrachi Function: Vice president of product development Signature:

Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.

FCC Radio Test Report FCC ID: X4YNXG150 This report concerns (check one): Original Grant Class II Change Project No. Equipment Model Name Applicant Address

: 1411C285

: NexxtGate 150 High Power Access Point

: AEOPLDR4U2

: NEXXT SOLUTIONS

: 3505 N.W 107TH AVE,MIAMI ,FL,33178 Date of Receipt Date of Test Issued Date Tested by

: Dec. 01, 2014

: Dec. 01, 2014 ~ Dec. 18, 2014

: Dec. 19, 2014

: BTL Inc. Testing Engineer Technical Manager Authorized Signatory

:

:

:

(David Mao)

(Leo Hung)

(Steven Lu) BT L INC . No.3, Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, TEL: +86-769-8318-3000 FAX: +86-769-8319-6000 Guangdong, China. Report No.: BTL-FCCP-1-1411C285 Page 1 of 188 Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C, or National Institute of Standards and Technology (NIST) of U.S.A. BTL's reports apply only to the specific samples tested under conditions. It is manufacture s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL shall have no liability for any declarations, inf drawn by the client or others from BTL issued reports. erences or generalizations BTLs reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of BTL-self, extracts from the test report shall not be reproduced except in full with BTLs authorized written approval. the client. As a mutual protection to the clients, the public and and accredited by the conformity assessment authorities listed in this test report. BTLs laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: BTL-FCCP-1-1411C285 Page 2 of 188 Table of Contents Page 3 . GENERAL INFORMATION 1 . CERTIFICATION 2 . SUMMARY OF TEST RESULTS 2.1 TEST FACILITY 2.2 MEASUREMENT UNCERTAINTY 6 7 8 8 9 9 3.1 GENERAL DESCRIPTION OF EUT 3.2 DESCRIPTION OF TEST MODES 11 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 12 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 13 3.5 DESCRIPTION OF SUPPORT UNITS 13 4 . EMC EMISSION TEST 14 4.1 CONDUCTED EMISSION MEASUREMENT 14 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 14 4.1.2 TEST PROCEDURE 14 4.1.3 DEVIATION FROM TEST STANDARD 14 4.1.4 TEST SETUP 15 4.1.5 EUT OPERATING CONDITIONS 15 4.1.6 EUT TEST CONDITIONS 15 4.1.7 TEST RESULTS 15 4.2 RADIATED EMISSION MEASUREMENT 16 4.2.1 RADIATED EMISSION LIMITS 16 4.2.2 TEST PROCEDURE 17 4.2.3 DEVIATION FROM TEST STANDARD 17 4.2.4 TEST SETUP 17 4.2.5 EUT OPERATING CONDITIONS 18 4.2.6 EUT TEST CONDITIONS 18 4.2.7 TEST RESULTS (9KHZ TO 30MHZ) 19 4.2.8 TEST RESULTS (BETWEEN 30MHZ TO 1000 MHZ) 19 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) 19 5 . BANDWIDTH TEST 20 5.1 APPLIED PROCEDURES 20 5.1.1 TEST PROCEDURE 20 5.1.2 DEVIATION FROM STANDARD 20 5.1.3 TEST SETUP 20 5.1.4 EUT OPERATION CONDITIONS 20 5.1.5 EUT TEST CONDITIONS 20 5.1.6 TEST RESULTS 20 Report No.: BTL-FCCP-1-1411C285 Page 3 of 188 Table of Contents Page 6 . MAXIMUM PEAK CONDUCTED OUTPUT POWER TEST 21 6.1 APPLIED PROCEDURES / LIMIT 21 6.1.1 TEST PROCEDURE 21 6.1.2 DEVIATION FROM STANDARD 21 6.1.3 TEST SETUP 21 6.1.4 EUT OPERATION CONDITIONS 21 6.1.5 EUT TEST CONDITIONS 21 6.1.6 TEST RESULTS 21 7 . ANTENNA CONDUCTED SPURIOUS EMISSION 22 7.1 APPLIED PROCEDURES / LIMIT 22 7.1.1 TEST PROCEDURE 22 7.1.2 DEVIATION FROM STANDARD 22 7.1.3 TEST SETUP 22 7.1.4 EUT OPERATION CONDITIONS 22 7.1.5 EUT TEST CONDITIONS 22 7.1.6 TEST RESULTS 22 8 . POWER SPECTRAL DENSITY TEST 23 8.1 APPLIED PROCEDURES / LIMIT 23 8.1.1 TEST PROCEDURE 23 8.1.2 DEVIATION FROM STANDARD 23 8.1.3 TEST SETUP 23 8.1.4 EUT OPERATION CONDITIONS 23 8.1.5 EUT TEST CONDITIONS 23 8.1.6 TEST RESULTS 23 9 . MEASUREMENT INSTRUMENTS LIST 24 10 . EUT TEST PHOTO 26 ATTACHMENT A - CONDUCTED EMISSION 34 ATTACHMENT B - RADIATED EMISSION (9KHZ TO 30MHZ) 39 ATTACHMENT C - RADIATED EMISSION (30MHZ TO 1000MHZ) 42 ATTACHMENT D - RADIATED EMISSION (ABOVE 1000MHZ) 55 ATTACHMENT E - BANDWIDTH 152 ATTACHMENT F MAXIMUM PEAK CONDUCTED OUTPUT POWER 161 ATTACHMENT G - ANTENNA CONDUCTED SPURIOUS EMISSION 163 ATTACHMENT H - POWER SPECTRAL DENSITY 180 Report No.: BTL-FCCP-1-1411C285 Page 4 of 188 REPORT ISSUED HISTORY Issued No. BTL-FCCP-1-1411C285 Description Original Issue. Issued Date Dec. 19, 2014 Report No.: BTL-FCCP-1-1411C285 Page 5 of 188

:

: NEXXT SOLUTIONS

: Dec. 01, 2014 ~ Dec. 18, 2014 NexxtGate 150 High Power Access Point 1. CERTIFICATION Equipment Brand Name : NEXXT Model Name : AEOPLDR4U2 Applicant Date of Test Test Sample : ENGINEERING SAMPLE Standard(s) The above equipment has been tested and found compliance with the requirement of the relative standards by BTL Inc. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. BTL-FCCP-1-1411C285) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of TAF according to the ISO-17025 quality assessment standard and technical standard(s).

: FCC Part15, Subpart C: 2013 (15.247) / ANSI C63.4-2009 Report No.: BTL-FCCP-1-1411C285 Page 6 of 188 2. SUMMARY OF TEST RESULTS Test procedures according to the technical standard(s):

Applied Standard(s): FCC Part15 (15.247) , Subpart C: 2013 Standard(s) Section FCC 15.207 15.247(d) 15.247(a)(2) 15.247(b)(3) 15.247(e) 15.203 15.209/15.205 Test Item Judgment Remark Conducted Emission Antenna conducted Spurious Emission 6dB Bandwidth Peak Output Power Power Spectral Density Antenna Requirement Transmitter Radiated Emissions PASS PASS PASS PASS PASS PASS PASS NOTE:

(1) N/A denotes test is not applicable in this test report.

(2) The test follows FCC KDB Publication No. 558074 D01 DTS Meas Guidance v03r02

(Measurement Guidelines of DTS) Report No.: BTL-FCCP-1-1411C285 Page 7 of 188 2.1 TEST FACILITY The test facilities used to collect the test data in this report is DG-C02/DG-CB03 at the location of No.3,Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, Guangdong, China.523792 BTL's test firm number for FCC: 319330 2.2 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2:

The reported uncertainty of measurement y ? U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %0 A. Conducted Measurement :

Test Site Method Measurement Frequency Range DG-C02 CISPR 150 KHz ~ 30MHz U, (dB) 1.94 NOTE B. Radiated Measurement :

Test Site Method Measurement Frequency Range 9KHz~30MHz 9KHz~30MHz 30MHz ~ 200MHz 30MHz ~ 200MHz 200MHz ~ 1,000MHz 200MHz ~ 1,000MHz 1GHz~18GHz 1GHz~18GHz 18GHz~40GHz 18GHz~40GHz Ant. H / V U, (dB) V 3.79 3.57 H 3.82 V 3.60 H V 3.86 3.94 H 3.12 V 3.68 H V 4.15 4.14 H NOTE DG-CB03 CISPR Report No.: BTL-FCCP-1-1411C285 Page 8 of 188 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT Equipment Brand Name Model Name Model Difference NexxtGate 150 High Power Access Point NEXXT AEOPLDR4U2 N/A Operation Frequency Modulation Technology Product Description Bit Rate of Transmitter Output Power (Max.) 2412~2462 MHz 802.11b:DSSS 802.11g:OFDM 802.11n:OFDM 802.11b: 11/5.5/2/1 Mbps 802.11g:

54/48/36/24/18/12/9/6 Mbps 802.11n up to 150 Mbps 802.11b: 18.75dBm 802.11g: 25.30dBm 802.11n(20MHz):23.00dBm 802.11n(40MHz): 21.10dBm Power Source Power Rating DC voltage supplied from AC/DC adapter. Brand: NEXXT Model: TEA12-12150 I/P: AC 100-240V 50/60Hz 0.6A O/P: DC 12V/1.5 A Note:

1. For a more detailed features description, please refer to the manufacturers specifications or the User's Manual. Report No.: BTL-FCCP-1-1411C285 Page 9 of 188 2. Channel List:

CH01 CH11 for 802.11b, 802.11g, 802.11n(20MHz) CH03 CH09 for 802.11n(40MHz) Channel 01 02 03 Frequency

(MHz) 2412 2417 2422 Channel 04 05 06 Frequency

(MHz) 2427 2432 2437 Channel 07 08 09 Frequency

(MHz) 2442 2447 2452 Channel 10 11 Frequency

(MHz) 2457 2462 3. Table for Filed Antenna Ant. 1 2 Brand N/A Tenda Model Name Antenna Type N/A Q5091 Internal Diople Connector N/A N/A Gain 10.00 5.07 Note TX/RX TX/RX Note:

1. Anenna 1 and antenna 2 is optional and only one antenna is used at a time. These two antennas can not transmit simultaneously. Report No.: BTL-FCCP-1-1411C285 Page 10 of 188 3.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 TX B MODE CHANNEL 01/06/11 TX G MODE CHANNEL 01/06/11 TX N-20MHZ MODE CHANNEL 01/06/11 TX N-40MHZ MODE CHANNEL 03/06/09 TX MODE The EUT system operated these modes were found to be the worst case during the pre-scanning test as following:

Final Test Mode Mode 5 For Conducted Test Description TX MODE For Radiated Test Final Test Mode Description Mode 1 Mode 2 Mode 3 Mode 4 TX B MODE CHANNEL 01/06/11 TX G MODE CHANNEL 01/06/11 TX N-20MHZ MODE CHANNEL 01/06/11 TX N-40MHZ MODE CHANNEL 03/06/09 Note:

(1) The measurements are performed at the high, middle, low available channels.

(2) 802.11b mode: DBPSK (1Mbps) 802.11g mode: OFDM (6Mbps) 802.11n HT20 mode : BPSK (6.5Mbps) 802.11n HT40 mode : BPSK (13.5Mbps) For radiated emission tests, the highest output powers were set for final test.

(3) For radiated below 1G test, the 802.11b is found to be the worst case and recorded.

(4) The EUT was pro grammed to be in continuously transmitting mode and the transmit duty cycle is not less than 98%. Report No.: BTL-FCCP-1-1411C285 Page 11 of 188 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING During testing, channel & power controlling software provided by the customer was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the customer and is going to be fixed on the firmware of the final end product power parameters of WLAN Test software version Frequency (MHz) 802.11b 802.11g 802.11n (20MHz) Frequency 802.11n (40MHz) 2412 55 48 40 2422 42 MTOOL_2.0.0.3 2437 57 62 56 2437 46 2462 50 48 46 2452 41 Report No.: BTL-FCCP-1-1411C285 Page 12 of 188 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED C-1 EUT E-1 Notebook 3.5 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item E-1 Equipment Notebook Mfr/Brand Model/Type No. FCC ID/IC Series No. Note DELL INSPIRON 1420 DOC N/A Item Shielded Type Ferrite Core C-1 NO NO Length 10m Note RJ-45 Cable Report No.: BTL-FCCP-1-1411C285 Page 13 of 188 4. EMC EMISSION TEST 4.1 CONDUCTED EMISSION MEASUREMENT 4.1.1 POWER LINE CONDUCTED EMISSION Limits

(Frequency Range 150KHz-30MHz) Frequency of Emission (MHz) 0.15 -0.5 0.50 -5.0 5.0 -30.0 Note:

Conducted Limit (dBV) Quasi-peak 66 to 56*

56 60 Average 56 to 46*

46 50

(1) The limit of " * " decreases with the logarithm of the frequency

(2) The test result calculated as following:

Measurement Value = Reading Level + Correct Factor Correct Factor = Insertion Loss + Cable Loss + Attenuator Factor(if use) Margin Level = Measurement Value Limit Value The following table is the setting of the receiver Receiver Parameters Attenuation Start Frequency Stop Frequency IF Bandwidth Setting 10 dB 0.15 MHz 30 MHz 9 KHz 4.1.2 TEST PROCEDURE a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the and forth in the center forming a bundle 30 to 40 cm long. cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item EUT Test Photos. 4.1.3 DEVIATION FROM TEST STANDARD No deviation Report No.: BTL-FCCP-1-1411C285 Page 14 of 188 4.1.4 TEST SETUP Ver tical Referenc e Gro u n d Plan e 40c m EU T Test Rec eive r LIS N 80c m Note: 1.Su p p ort u nits were co n nected to seco n d LISN . 2.Both of LISNs (AMN) are 80 cm from EUT an d at least 8 0 f rom other u nits and other metal plane s Horizo nta l Gro u n d Plan e Referenc e 4.1.5 EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been program med to continuously transmit during test. This operating condition was tested and used to collect the included data. 4.1.6 EUT TEST CONDITIONS Temperature: 25C Relative Humidity: 55% Test Voltage: AC 120V/60Hz 4.1.7 TEST RESULTS Please refer to the Attachment A. Report No.: BTL-FCCP-1-1411C285 Page 15 of 188 4.2 RADIATED EMISSION MEASUREMENT 4.2.1 RADIATED EMISSION LIMITS 20dB in any 100 KHz bandwidth outside the operating frequency band. In case the emission fall within the restricted band specified on 15.205(a), then the 15.209(a) limit in the table below has to be followed. LIMITS OF RADIATED EMISSION MEASUREMENT (9KHz-1000MHz) Frequency

(MHz) 0.009~0.490 0.490~1.705 1.705~30.0 30~88 88~216 216~960 960~1000 Field Strength

(microvolts/meter) 2400/F(KHz) 24000/F(KHz) 30 100 150 200 500 Measurement Distance

(meters) 300 30 30 3 3 3 3 LIMITS OF RADIATED EMISSION MEASUREMENT (Above 1000MHz) Frequency (MHz) Above 1000 Notes:

(dBuV/m) (at 3 meters) PEAK 74 AVERAGE 54

(1) The limit for radiated test was performed according to FCC PART 15C.

(2) The tighter limit applies at the band edges.

(3) Emission level (dBuV/m)=20log Emission level (uV/m). Spectrum Parameter Attenuation Start Frequency Stop Frequency RBW / VBW Setting Auto 1000 MHz 10th carrier harmonic RBW 1MHz VBW 3MHz peak detector for Pk value

(Emission in restricted band) RMS detector for AV value Receiver Parameter Attenuation Start ~ Stop Frequency Start ~ Stop Frequency Start ~ Stop Frequency Start ~ Stop Frequency Start ~ Stop Frequency Setting Auto 9KHz~90KHz for PK/AVG detector 90KHz~110KHz for QP detector 110KHz~490KHz for PK/AVG detector 490KHz~30MHz for QP detector 30MHz~1000MHz for QP detector Report No.: BTL-FCCP-1-1411C285 Page 16 of 188 4.2.2 TEST PROCEDURE a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation.(below 1GHz) b. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter fully-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation.(above 1GHz) c. The height of the equipment or of the substitution antenna shall be 0.8 m; the height of the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. e. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed. f. For the actual test configuration, please refer to the related Item EUT Test Photos. 4.2.3 DEVIATION FROM TEST STANDARD No deviation 4.2.4 TEST SETUP

(A) Radiated Emission Test Set-Up Frequency Below 1 GHz Report No.: BTL-FCCP-1-1411C285 Page 17 of 188

(B) Radiated Emission Test Set-Up Frequency Above 1 GHz

(C) For radiated emissions below 30MHz 4.2.5 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 4.1.5 Unless otherwise a special operating condition is specified in the follows during the testing. 4.2.6 EUT TEST CONDITIONS Temperature: 25C Relative Humidity: 55% Test Voltage: AC 120V/60Hz Report No.: BTL-FCCP-1-1411C285 Page 18 of 188 4.2.7 TEST RESULTS (9KHZ TO 30MHZ) Please refer to the Attachment B Remark:

the permissible value has no need to be reported.

(1) The amplitude of spurious emissions which are attenuated by more than 20 dB below

(2) Distance extrapolation factor = 40 log (specific distance / test distance) (dB).

(3) Limit line = specific limits (dBuV) + distance extrapolation factor. 4.2.8 TEST RESULTS (BETWEEN 30MHZ TO 1000 MHZ) Please refer to the Attachment C. 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) Please refer to the Attachment D. Remark:

For fundamental signal judgment was referred to Peak output test.

(1) No limit: This is fundamental signal, the judgment is not applicable. Report No.: BTL-FCCP-1-1411C285 Page 19 of 188 5. BANDWIDTH TEST 5.1 APPLIED PROCEDURES FCC Part15 (15.247) , Subpart C Section 15.247(a)(2) Test Item Bandwidth Frequency Range

(MHz) 2400-2483.5 Result PASS 5.1.1 TEST PROCEDURE a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in b. Spectrum Setting: RBW= 100KHz, VBW=300KHz, Sweep time = 2.5 ms. the block diagram below, 5.1.2 DEVIATION FROM STANDARD No deviation. 5.1.3 TEST SETUP 5.1.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 4.1.5 Unless otherwise a special operating condition is specified in the follows during the testing. 5.1.5 EUT TEST CONDITIONS Temperature: 25C Relative Humidity: 55% Test Voltage: AC 120V/60Hz 5.1.6 TEST RESULTS Please refer to the Attachment E. Report No.: BTL-FCCP-1-1411C285 Page 20 of 188 6. MAXIMUM PEAK CONDUCTED OUTPUT POWER TEST 6.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247) , Subpart C Section Test Item Limit Frequency Range

(MHz) Result 15.247(b)(3) Maximum Output Power 6.1.1 TEST PROCEDURE 1 Watt or 30dBm 2400-2483.5 PASS a. The EUT was directly connected to the power meter and antenna output port as show in the block diagram below, b. The maximum peak conducted output power was performed in accordance with method 9.1.2 of FCC KDB 558074 D01 DTS Meas Guidance v03r02. 6.1.2 DEVIATION FROM STANDARD No deviation. 6.1.3 TEST SETUP 6.1.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 4.1.5 Unless otherwise a special operating condition is specified in the follows during the testing. Transmit output power was measured while the host equipment supply voltage was varied from 85 % to 115 % of the nominal rated supply voltage. No change in transmit output power was observed. 6.1.5 EUT TEST CONDITIONS Temperature: 25C Relative Humidity: 55% Test Voltage: AC 120V/60Hz 6.1.6 TEST RESULTS Please refer to the Attachment F. Report No.: BTL-FCCP-1-1411C285 Page 21 of 188 7. ANTENNA CONDUCTED SPURIOUS EMISSION 7.1 APPLIED PROCEDURES / LIMIT In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. 7.1.1 TEST PROCEDURE a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in b. Spectrum Setting: RBW= 100KHz, VBW=300KHz, Sweep time = Auto. the block diagram below, 7.1.2 DEVIATION FROM STANDARD No deviation. 7.1.3 TEST SETUP 7.1.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 4.1.5 Unless otherwise a special operating condition is specified in the follows during the testing. 7.1.5 EUT TEST CONDITIONS Temperature: 25C Relative Humidity: 55% Test Voltage: AC 120V/60Hz 7.1.6 TEST RESULTS Please refer to the Attachment G. Report No.: BTL-FCCP-1-1411C285 Page 22 of 188 8. POWER SPECTRAL DENSITY TEST 8.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247) , Subpart C Section Test Item Limit 15.247(e) Power Spectral Density 8 dBm

(in any 3KHz) Frequency Range

(MHz) Result 2400-2483.5 PASS 8.1.1 TEST PROCEDURE a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in b. Spectrum Setting: RBW=3KHz, VBW=10KHz, Sweep time = Auto. the block diagram below, 8.1.2 DEVIATION FROM STANDARD No deviation. 8.1.3 TEST SETUP 8.1.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 4.1.5 Unless otherwise a special operating condition is specified in the follows during the testing. 8.1.5 EUT TEST CONDITIONS Temperature: 25C Relative Humidity: 55% Test Voltage: AC 120V/60Hz 8.1.6 TEST RESULTS Please refer to the Attachment H. Report No.: BTL-FCCP-1-1411C285 Page 23 of 188 9. MEASUREMENT INSTRUMENTS LIST Item Kind of Equipment 1 2 3 4 5 6 LISN LISN Test Cable EMI TEST RECEIVER 50 Terminator Measurement Software Item Kind of Equipment 1 2 3 4 5 6 7 8 Antenna Amplifier Receiver Test Cable Controller Antenna Amplifier Receiver Test Cable Controller 9 10 11 Broad-Band Horn Antenna Microwave Preamplifier With 12 13 14 Adaptor Active Loop Antenna Measurement Software Calibrated until Mar. 29, 2015 Mar. 29, 2015 Mar. 14, 2015 Conducted Emission Measurement Manufacturer Type No. 3816/2 ENV216 C_17 Serial No. 00052765 101447 N/A EMCO R&S N/A R&S SHX Farad ESCS30 833364/017 Mar. 29, 2015 TF2-3G-A EZ-EMC Ver.NB-03A1

-01 08122902 Mar. 29, 2015 N/A N/A Radiated Emission Measurement Manufacturer Schwarbeck HP AGILENT N/A CT ETS Agilent AGILENT HUBER+SUHNER CT Type No. VULB9160 8447D N9038A C-01_CB03 SC100 3115 8449B N9038A C-48 SC100 Serial No. Calibrated until 9160-3232 Mar. 29, 2015 2944A09673 Mar. 29, 2015 MY5213003 Sep. 30, 2015 Jul. 01, 2015 N/A 00075789 Mar. 29, 2015 3008A02274 Mar. 29, 2015 MY5213003 Sep. 30, 2015 9 N/A N/A 9 N/A N/A Apr. 30, 2015 N/A Schwarzbeck BBHA 9170 9170319 Feb. 22, 2015 EMC INSTRUMENT EMC2654045 980039 &

HA01 Feb. 22, 2015 R&S Farad HFH2-Z2 EZ-EMC Ver.NB-03A1-01 830749/020 Mar. 29, 2015 N/A N/A Report No.: BTL-FCCP-1-1411C285 Page 24 of 188 6dB Bandwidth Measurement Item Kind of Equipment 1 Spectrum Analyzer Manufacturer R&S Type No. FSP 40 Serial No. 100185 Calibrated until Nov. 02, 2015 Item 1 2 Kind of Equipment P-series Power Wireband Power meter sensor Peak Output Power Measurement Manufacturer Type No. Serial No. Calibrated until Agilent Agilent N1911A MY45100473 Mar. 29, 2015 N1921A MY51100041 Mar. 29, 2015 Antenna Conducted Spurious Emission Measurement Item Kind of Equipment Manufacturer 1 Spectrum Analyzer R&S Type No. FSP 40 Serial No. 100185 Calibrated until Nov. 02, 2015 Item Kind of Equipment 1 Spectrum Analyzer R&S Type No. FSP 40 Serial No. 100185 Calibrated until Nov. 02, 2015 Power Spectral Density Measurement Manufacturer Remark: N/A denotes no model name, serial no. or calibration specified. All calibration period of equipment list is one year. Report No.: BTL-FCCP-1-1411C285 Page 25 of 188 10. EUT TEST PHOTO Conducted Measurement Photos-Internal Antenna Report No.: BTL-FCCP-1-1411C285 Page 26 of 188 Conducted Measurement Photos-External Antenna Report No.: BTL-FCCP-1-1411C285 Page 27 of 188 Radiated Measurement Photos-Internal Antenna 9KHz to 30MHz Report No.: BTL-FCCP-1-1411C285 Page 28 of 188 Radiated Measurement Photos-Internal Antenna 30MHz to 1000MHz Report No.: BTL-FCCP-1-1411C285 Page 29 of 188 Radiated Measurement Photos-Internal Antenna Above 1000MHz Report No.: BTL-FCCP-1-1411C285 Page 30 of 188 Radiated Measurement Photos-External Antenna 9KHz to 30MHz Report No.: BTL-FCCP-1-1411C285 Page 31 of 188 Radiated Measurement Photos-External Antenna 30MHz to 1000MHz Report No.: BTL-FCCP-1-1411C285 Page 32 of 188 Radiated Measurement Photos-External Antenna Above 1000MHz Report No.: BTL-FCCP-1-1411C285 Page 33 of 188 ATTACHMENT A - CONDUCTED EMISSION Report No.: BTL-FCCP-1-1411C285 Page 34 of 188 Test Mode :

TX MODE-Internal Antenna Line Report No.: BTL-FCCP-1-1411C285 Page 35 of 188 Test Mode :

TX MODE-Internal Antenna Neutral Report No.: BTL-FCCP-1-1411C285 Page 36 of 188 Test Mode :

TX MODE-External Antenna Line Report No.: BTL-FCCP-1-1411C285 Page 37 of 188 Test Mode :

TX MODE-External Antenna Neutral Report No.: BTL-FCCP-1-1411C285 Page 38 of 188 ATTACHMENT B - RADIATED EMISSION (9KHZ TO 30MHZ) Report No.: BTL-FCCP-1-1411C285 Page 39 of 188 Test Mode:

TX Mode-Internal Antenna Reading(RA)Corr.Factor(CF)Measured(FS)

(dBuV/m) Freq.

(MHz) 0.0093 0.0093 0.0236 0.0236 0.0312 0.0312 0.0432 0.0432 0.5245 1.7178 Freq.

(MHz) 0.0094 0.0094 0.0261 0.0261 0.0351 0.0351 0.0463 0.0463 0.4942 1.7174 Ant. 0/90 0 0 0 0 0 0 0 0 0 0 Ant. 0/90 90 90 90 90 90 90 90 90 90 90

(dBuV) 1.84 9.52 1.41 9.68 1.21 9.79 2.86 10.73 8.78 11.62

(dBuV) 3.06 11.43 1.51 10.63 2.64 9.81 2.54 10.36 8.89 11.52

(dB) 24.98 24.98 24.07 24.07 23.59 23.59 22.83 22.83 19.88 19.53

(dB) 24.30 24.30 23.91 23.91 23.34 23.34 22.63 22.63 19.81 19.53 26.82 34.50 25.48 33.75 24.80 33.38 25.69 33.56 28.66 31.15 27.36 35.73 25.42 34.54 25.98 33.15 25.17 32.99 28.70 31.05 Limits(QP)

(dBuV/m) 108.23 128.23 100.15 120.15 97.72 117.72 94.89 114.89 73.21 69.54 Limits(QP)

(dBuV/m) 128.14 148.14 119.27 139.27 116.70 136.70 114.29 134.29 73.73 69.54 Margin

(dB)

-81.42

-93.74

-74.66

-86.39

-72.92

-84.34

-69.20

-81.33

-44.55

-38.39 Margin

(dB)

-100.78

-112.41

-93.85

-104.73

-90.71

-103.54

-89.12

-101.30

-45.02

-38.49 Note AVG PEAK AVG PEAK AVG PEAK AVG PEAK QP QP Note AVG PEAK AVG PEAK AVG PEAK AVG PEAK QP QP Reading(RA)Corr.Factor(CF)Measured(FS)

(dBuV/m) Report No.: BTL-FCCP-1-1411C285 Page 40 of 188 Test Mode:

TX Mode-External Antenna Reading(RA)Corr.Factor(CF)Measured(FS)

(dBuV/m) Freq.

(MHz) 0.0163 0.0163 0.0354 0.0354 0.0383 0.0383 0.0464 0.0464 2.0651 3.3675 Freq.

(MHz) 0.0153 0.0153 0.0334 0.0334 0.0371 0.0371 0.0679 0.0679 2.0563 3.2474 Ant. 0/90 0 0 0 0 0 0 0 0 0 0 Ant. 0/90 90 90 90 90 90 90 90 90 90 90

(dBuV) 13.64 14.55 6.79 7.58 3.57 5.36 0.87 2.86 30.64 21.66

(dBuV) 13.38 14.45 6.53 8.74 3.62 5.38 0.64 2.91 30.64 21.69

(dB) 24.53 24.53 23.32 23.32 23.14 23.14 22.63 22.63 19.46 18.94

(dB) 24.30 24.30 23.45 23.45 23.22 23.22 22.04 22.04 19.47 18.92 38.17 39.08 30.11 30.90 26.71 28.50 23.50 25.49 50.10 40.60 37.68 38.75 29.98 32.19 26.84 28.60 22.68 24.95 50.11 40.61 Limits(QP)

(dBuV/m) 103.36 123.36 96.62 116.62 95.94 115.94 94.27 114.27 69.54 69.54 Limits(QP)

(dBuV/m) 123.91 143.91 117.13 137.13 116.22 136.22 110.97 130.97 69.54 69.54 Margin

(dB)

-65.19

-84.28

-66.51

-85.72

-69.23

-87.44

-70.78

-88.79

-19.44

-28.94 Margin

(dB)

-86.23

-105.16

-87.15

-104.94

-89.38

-107.62

-88.28

-106.01

-19.43

-28.93 Note AVG PEAK AVG PEAK AVG PEAK AVG PEAK QP QP Note AVG PEAK AVG PEAK AVG PEAK AVG PEAK QP QP Reading(RA)Corr.Factor(CF)Measured(FS)

(dBuV/m) Report No.: BTL-FCCP-1-1411C285 Page 41 of 188 ATTACHMENT C - RADIATED EMISSION (30MHZ TO 1000MHZ) Report No.: BTL-FCCP-1-1411C285 Page 42 of 188 Test Mode:

TX B MODE CHANNEL 01-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 43 of 188 Test Mode:

TX B MODE CHANNEL 01-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 44 of 188 Test Mode:

TX B MODE CHANNEL 06-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 45 of 188 Test Mode:

TX B MODE CHANNEL 06-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 46 of 188 Test Mode:

TX B MODE CHANNEL 11-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 47 of 188 Test Mode:

TX B MODE CHANNEL 11-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 48 of 188 Test Mode:

TX B MODE CHANNEL 01-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 49 of 188 Test Mode:

TX B MODE CHANNEL 01-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 50 of 188 Test Mode:

TX B MODE CHANNEL 06-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 51 of 188 Test Mode:

TX B MODE CHANNEL 06-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 52 of 188 Test Mode:

TX B MODE CHANNEL 11-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 53 of 188 Test Mode:

TX B MODE CHANNEL 11-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 54 of 188 ATTACHMENT D - RADIATED EMISSION (ABOVE 1000MHZ) Report No.: BTL-FCCP-1-1411C285 Page 55 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2412MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 56 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2412MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 57 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2412MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 58 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2412MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 59 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2437MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 60 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2437MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 61 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2437MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 62 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2437MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 63 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2462MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 64 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2462MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 65 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2462MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 66 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2462MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 67 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2412MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 68 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2412MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 69 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2412MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 70 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2412MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 71 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2437MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 72 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2437MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 73 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2437MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 74 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2437MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 75 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2462MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 76 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2462MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 77 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2462MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 78 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2462MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 79 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2412MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 80 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2412MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 81 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2412MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 82 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2412MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 83 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2437MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 84 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2437MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 85 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2437MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 86 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2437MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 87 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2462MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 88 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2462MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 89 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2462MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 90 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2462MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 91 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2422MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 92 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2422MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 93 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2422MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 94 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2422MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 95 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2437MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 96 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2437MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 97 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2437MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 98 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2437MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 99 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2452MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 100 of 188

Orthogonal Axis : X Test Mode :

TX N-40M MODE 2452MHz-Internal Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 101 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2452MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 102 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2452MHz-Internal Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 103 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2412MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 104 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2412MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 105 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2412MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 106 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2412MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 107 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2437MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 108 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2437MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 109 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2437MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 110 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2437MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 111 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2462MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 112 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2462MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 113 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2462MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 114 of 188 Orthogonal Axis : X Test Mode :

TX B MODE 2462MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 115 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2412MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 116 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2412MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 117 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2412MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 118 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2412MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 119 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2437MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 120 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2437MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 121 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2437MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 122 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2437MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 123 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2462MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 124 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2462MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 125 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2462MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 126 of 188 Orthogonal Axis : X Test Mode :

TX G MODE 2462MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 127 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2412MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 128 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2412MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 129 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2412MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 130 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2412MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 131 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2437MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 132 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2437MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 133 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2437MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 134 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2437MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 135 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2462MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 136 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2462MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 137 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2462MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 138 of 188 Orthogonal Axis : X Test Mode :

TX N-20M MODE 2462MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 139 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2422MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 140 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2422MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 141 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2422MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 142 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2422MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 143 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2437MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 144 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2437MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 145 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2437MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 146 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2437MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 147 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2452MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 148 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2452MHz-External Antenna Vertical Report No.: BTL-FCCP-1-1411C285 Page 149 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2452MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 150 of 188 Orthogonal Axis : X Test Mode :

TX N-40M MODE 2452MHz-External Antenna Horizontal Report No.: BTL-FCCP-1-1411C285 Page 151 of 188 ATTACHMENT E - BANDWIDTH Report No.: BTL-FCCP-1-1411C285 Page 152 of 188 Test Mode : TX B Mode_CH01/06/11 Frequency

(MHz) 2412 2437 2462 6dB Bandwidth

(MHz) 7.98 8.16 8.06 99% Occupied BW Min. Limit

(MHz) 10.12 10.12 10.12 TX CH01

(kHz) 500 500 500 Test Result Complies Complies Complies Report No.: BTL-FCCP-1-1411C285 Page 153 of 188 TX CH06 TX CH11 Report No.: BTL-FCCP-1-1411C285 Page 154 of 188 Test Mode: TX G Mode_CH01/06/11 Frequency

(MHz) 2412 2437 2462 6dB Bandwidth

(MHz) 16.48 16.41 16.47 99% Occupied BW Min. Limit

(MHz) 16.52 16.52 16.52 TX CH01

(kHz) 500 500 500 Test Result Complies Complies Complies Report No.: BTL-FCCP-1-1411C285 Page 155 of 188 TX CH06 TX CH11 Report No.: BTL-FCCP-1-1411C285 Page 156 of 188 Test Mode : TX N-20MHz Mode_CH01/06/11 Frequency

(MHz) 2412 2437 2462 6dB Bandwidth

(MHz) 17.64 17.62 17.67 99% Occupied BW Min. Limit

(MHz) 17.64 17.68 17.64 TX CH01

(kHz) 500 500 500 Test Result Complies Complies Complies Report No.: BTL-FCCP-1-1411C285 Page 157 of 188 TX CH06 TX CH11 Report No.: BTL-FCCP-1-1411C285 Page 158 of 188 Test Mode : TX N-40MHz Mode_CH03/06/09 Frequency

(MHz) 2422 2437 2452 6dB Bandwidth

(MHz) 35.44 36.15 35.44 99% Occupied BW Min. Limit

(MHz) 36.00 36.00 36.00

(kHz) 500 500 500 TX CH03 Test Result Complies Complies Complies Report No.: BTL-FCCP-1-1411C285 Page 159 of 188 TX CH06 TX CH09 Report No.: BTL-FCCP-1-1411C285 Page 160 of 188 ATTACHMENT F MAXIMUM PEAK CONDUCTED OUTPUT POWER Report No.: BTL-FCCP-1-1411C285 Page 161 of 188 Test Mode :TX B Mode_CH01/06/11 Frequency

(MHz) 2412 2437 2462 Conducted Power

(dBm) 18.75 18.56 15.70 Conducted Power

(W) 0.07 0.07 0.04 Max. Limit

(dBm) 26.00 26.00 26.00 Max. Limit

(W) 0.40 0.40 0.40 Result Complies Complies Complies Test Mode :TX G Mode_CH01/06/11 Frequency

(MHz) 2412 2437 2462 Conducted Power

(dBm) 22.60 25.30 20.50 Conducted Power

(W) 0.18 0.34 0.11 Max. Limit

(dBm) 26.00 26.00 26.00 Max. Limit

(W) 0.40 0.40 0.40 Result Complies Complies Complies Test Mode :TX N20 Mode_CH01/06/11 Frequency

(MHz) 2412 2437 2462 Conducted Power

(dBm) 19.10 23.00 19.60 Conducted Power

(W) 0.08 0.20 0.09 Max. Limit

(dBm) 26.00 26.00 26.00 Max. Limit

(W) 0.40 0.40 0.40 Result Complies Complies Complies Test Mode :TX N40 Mode_CH03/06/09 Frequency

(MHz) 2422 2437 2452 Conducted Power

(dBm) 19.80 21.10 16.90 Conducted Power

(W) 0.10 0.13 0.05 Max. Limit

(dBm) 26.00 26.00 26.00 Max. Limit

(W) 1.00 1.00 1.00 Result Complies Complies Complies Report No.: BTL-FCCP-1-1411C285 Page 162 of 188 ATTACHMENT G - ANTENNA CONDUCTED SPURIOUS EMISSION Report No.: BTL-FCCP-1-1411C285 Page 163 of 188 Test Mode : TX B Mode Report No.: BTL-FCCP-1-1411C285 Page 164 of 188 TX B mode CH01 TX B mode CH11 Report No.: BTL-FCCP-1-1411C285 Page 165 of 188 TX B mode CH01 (10 Harmonic of the frequency) TX B mode CH06 (10 Harmonic of the frequency) Report No.: BTL-FCCP-1-1411C285 Page 166 of 188 TX B mode CH11 (10 Harmonic of the frequency) Report No.: BTL-FCCP-1-1411C285 Page 167 of 188 Test Mode : TX G Mode Report No.: BTL-FCCP-1-1411C285 Page 168 of 188 TX G mode CH01 TX G mode CH11 Report No.: BTL-FCCP-1-1411C285 Page 169 of 188 TX G mode CH01 (10 Harmonic of the frequency) TX G mode CH06 (10 Harmonic of the frequency) Report No.: BTL-FCCP-1-1411C285 Page 170 of 188 TX G mode CH11 (10 Harmonic of the frequency) Report No.: BTL-FCCP-1-1411C285 Page 171 of 188 Test Mode : TX N-20M Mode Report No.: BTL-FCCP-1-1411C285 Page 172 of 188 TX HT20 mode CH01 TX HT20 mode CH11 Report No.: BTL-FCCP-1-1411C285 Page 173 of 188 TX HT20 mode CH01 (10 Harmonic of the frequency) TX HT20 mode CH06 (10 Harmonic of the frequency) Report No.: BTL-FCCP-1-1411C285 Page 174 of 188 TX HT20 mode CH11 (10 Harmonic of the frequency) Report No.: BTL-FCCP-1-1411C285 Page 175 of 188 Test Mode : TX N-40M Mode Report No.: BTL-FCCP-1-1411C285 Page 176 of 188 TX HT40 mode CH03 TX HT40 mode CH09 Report No.: BTL-FCCP-1-1411C285 Page 177 of 188 TX HT40 mode CH03 (10 Harmonic of the frequency) TX HT40 mode CH06 (10 Harmonic of the frequency) Report No.: BTL-FCCP-1-1411C285 Page 178 of 188 TX HT40 mode CH09 (10 Harmonic of the frequency) Report No.: BTL-FCCP-1-1411C285 Page 179 of 188 ATTACHMENT H - POWER SPECTRAL DENSITY Report No.: BTL-FCCP-1-1411C285 Page 180 of 188 Test Mode :TX B Mode_CH01/06/11 Frequency

(MHz) 2412 2437 2462 Power Density

(dBm/3kHz) Power Density

(mW/3kHz) Max. Limit

(dBm/3kHz)

-11.19

-11.70

-14.18 0.08 0.07 0.04 TX CH01 4.00 4.00 4.00 Result Complies Complies Complies Report No.: BTL-FCCP-1-1411C285 Page 181 of 188 TX CH06 TX CH11 Report No.: BTL-FCCP-1-1411C285 Page 182 of 188 Test Mode :TX G Mode_CH01/06/11 Frequency

(MHz) 2412 2437 2462 Power Density

(dBm/3kHz) Power Density

(mW/3kHz) Max. Limit

(dBm/3kHz)

-17.89

-15.94

-19.25 0.02 0.03 0.01 TX CH01 4.00 4.00 4.00 Result Complies Complies Complies Report No.: BTL-FCCP-1-1411C285 Page 183 of 188 TX CH06 TX CH11 Report No.: BTL-FCCP-1-1411C285 Page 184 of 188 Test Mode : TX N-20M Mode_CH01/06/11 Frequency

(MHz) 2412 2437 2462 Power Density

(dBm/3kHz) Power Density

(mW/3kHz) Max. Limit

(dBm/3kHz)

-22.00

-18.77

-20.53 0.01 0.01 0.01 TX CH01 4.00 4.00 4.00 Result Complies Complies Complies Report No.: BTL-FCCP-1-1411C285 Page 185 of 188 TX CH06 TX CH11 Report No.: BTL-FCCP-1-1411C285 Page 186 of 188 Frequency

(MHz) 2422 2437 2452 Test Mode : TX N-40M Mode_CH03/06/09 Power Density

(dBm/3kHz) Power Density

(mW/3kHz) Max. Limit

(dBm/3kHz)

-21.61

-17.98

-20.18 0.01 0.02 0.01 TX CH03 4.00 4.00 4.00 Result Complies Complies Complies Report No.: BTL-FCCP-1-1411C285 Page 187 of 188 TX CH06 TX CH09 Report No.: BTL-FCCP-1-1411C285 Page 188 of 188

10. EUT TEST PHOTO Conducted Measurement Photos-Internal Antenna Report No.: BTL-FCCP-1-1411C285 Page 26 of 188 Conducted Measurement Photos-External Antenna Report No.: BTL-FCCP-1-1411C285 Page 27 of 188 Radiated Measurement Photos-Internal Antenna 9KHz to 30MHz Report No.: BTL-FCCP-1-1411C285 Page 28 of 188 Radiated Measurement Photos-Internal Antenna 30MHz to 1000MHz Report No.: BTL-FCCP-1-1411C285 Page 29 of 188 Radiated Measurement Photos-Internal Antenna Above 1000MHz Report No.: BTL-FCCP-1-1411C285 Page 30 of 188 Radiated Measurement Photos-External Antenna 9KHz to 30MHz Report No.: BTL-FCCP-1-1411C285 Page 31 of 188 Radiated Measurement Photos-External Antenna 30MHz to 1000MHz Report No.: BTL-FCCP-1-1411C285 Page 32 of 188 Radiated Measurement Photos-External Antenna Above 1000MHz Report No.: BTL-FCCP-1-1411C285 Page 33 of 188