FCC ID: 2AQURZW924 S2 Remote Control Switch

SIZE: 220 x 280 mm

材质：80G 书写纸

拆法：风琴页 55 x 70 mm 成品

正面

S2 Remote Control Switch

• MR40Z •

Spec：

Battery: CR2032*1

Frequency: 908.42MHz

Temperature Range: 32°F~104°F

Indoor use in dry location

Mounting plate

Screws x2

Screws x2

Face plate

Magets

Hang wallplate

Program button:

Battery：CR2032*1

Press 5x: Add Z-Wave Network

Press 5x: Remove Z-Wave Network

Press 5x: Wake-up Device

Reset :Press 5x while hold 5s,then press 5x again

RGB LED Indicator:

Inclusion: flashing blue

Exclusion: flashing purple

Wake up :stay solid blue

Reset :flashing red

1.Please read this the online guidels at support Minosto.com/Z-wave remote carefully

2.Do not use it in location with direct water contact.

3.Contains small parts keep away from children.

Power the device

Battery position

Open and access the battery

1.Use by hand open the remote cap,and push in to separate the 2 halves

2.Remove the battery tabs

3.Your Z-wave remove Immediately should flash LED to indicate it is powered.

S2 Remote Control Switch features：

1.Power by battery,no need wires needed.Note the ± direction of the battery

2.Control other Z-wave devices and enable scenes with a click of a button

3.The device with S2 and SmartStart support

Please contact us if you have any questions:

ask@minoston.com

www.minoston.com

Adding Device To your hub and Z-Wave Network for QR code

Z-wave Control

Choose your hub into and scan the QR code with your phone's camera and

add to Smartstar

Note:DSK Code can be foucd on packaging.

Do not remove or damage them.

Inclusion/Exclusion Function：

To add the device

1. Follow the instructions for your Z-Wave certified controller to adding device

from the Z-Wave network.

2. Once the controller is preparing to add your device, press the FIRST BUTTON(ONLY)

5 times, LED flashing in blue during inclusion and LED stays on green for 2 seconds

after inclusion successfully. If LED flashing purple for 3 seconds, please reset the

device. LED will stay on red for 2 seconds after inclusion failed.

To remove the device

1. Follow the instructions for your Z-Wave certified controller to remove a device

from the Z-Wave network.

2. Once the controller is preparing to remove your device, press the SECOND

BUTTON(ONLY) 5 times, LED flashing in purple during exclusion and the LED stays on

green for 2 seconds after exclusion successfully. LED will stay red for 2 seconds after

exclusion failed.

Wake up the Device:

Press the THIRD buttom 5 times quickly, LED will stay solid on blue when awake and

will turn off when device goes back to sleep mode.

Factory reset

Manual: Press the Fourth button 5 times, LED flashing red 5S while press 5 times again,

LED will stays red for 2 seconds then off.

Note:

Install the custom device handler to access the right functions

if you’re using the SmartThings hub. Please visit our website:

www.minoston.com or email us: ask@minoston.com.

Configuration Parameter:

Parameter 1 Battery report threshold %

Use it to set battery level for battery reports.

size=1 byte Available range : 1-20

(DEFAULT): 10%

Parameter 2 Low Battery alarm report

Use it to set battery level for low battery reports.

size=1 byte Available range : 5%-20%

(DEFAULT) : 5%

Parameter 3 LED Indicator Color for First button remote control (Scene 1 activation)

Choose the LED indicator color for First button remote control triggers

size=1 byte Available settings: 0--6

Value=0 White

Value=1 Purple

Value=2 Orange

Value=3 Cyan

Value=4 Red

Value=5 Green

Value=6 Blue

(DEFAULT) : 0

Parameter 4 LED Indicator Color for Second button remote control (Scene 2 activation)

Choose the LED indicator color for Second button remote control triggers

size=1 byte Available settings: 0--6

Value=0 White

Value=1 Purple

Value=2 Orange

Value=3 Cyan

Value=4 Red

Value=5 Green

Value=6 Blue

(DEFAULT) : 1

背面

Parameter 5 LED Indicator Color for Third button remote control (Scene 3 activation)

Choose the LED indicator color for Thrid button remote control triggers

size=1 byte Available settings: 0--6

Value=0 White

Value=1 Purple

Value=2 Orange

Value=3 Cyan

Value=4 Red

Value=5 Green

Value=6 Blue

(DEFAULT) : 2

Parameter 6 LED Indicator Color for Fourth button remote control (Scene 4 activation)

Choose the LED indicator color for Fourth button remote control triggers

size=1 byte Available settings: 0--6

Value=0 White

Value=1 Purple

Value=2 Orange

Value=3 Cyan

Value=4 Red

Value=5 Green

Value=6 Blue

(DEFAULT) : 3

Command Class

Generic Device Class: 0x07 - GENERIC_TYPE_SENSOR_NOTIFICATION

Specific Device Class: 0x01 - SPECIFIC_TYPE_NOTIFICATION_SENSOR

Command Classes:

0x5E - COMMAND_CLASS_ZWAVEPLUS_INFO

0x85 - COMMAND_CLASS_ASSOCIATION

0x8E - COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION

0x59 - COMMAND_CLASS_ASSOCIATION_GRP_INFO

0x31 - COMMAND_CLASS_SENSOR_MULTILEVEL

0x55 - COMMAND_CLASS_TRANSPORT_SERVICE

0x86 - COMMAND_CLASS_VERSION

0x72 - COMMAND_CLASS_MANUFACTURER_SPECIFIC

0x5A - COMMAND_CLASS_DEVICE_RESET_LOCALLY

0x73 - COMMAND_CLASS_POWERLEVEL

0x80 - COMMAND_CLASS_BATTERY

0x9F - COMMAND_CLASS_SECURITY_2

0x71 - COMMAND_CLASS_NOTIFICATION

0x87 - COMMAND_CLASS_INDICATOR

0x30 - COMMAND_CLASS_SENSOR_BINARY

0x70 - COMMAND_CLASS_CONFIGURATION

0x84 - COMMAND_CLASS_WAKE_UP

0x6C - COMMAND_CLASS_SUPERVISION

0x7A - COMMAND_CLASS_FIRMWARE_UPDATE_MD

Parameter 7 LED Indicator Brightness

Choose the LED indicator Brightness level

size=1 byte Available settings: 0--10

Value=0 LED off

Value=1 10% Brightness

Value=2 20% Brightness

Value=3 30% Brightness

Value=4 40% Brightness

Value=5 50% Brightness

Value=6 60% Brightness

Value=7 70% Brightness

Value=8 80% Brightness

Value=9 90% Brightness

Value=10 100% Brightness

(DEFAULT) : 5

Scene Control:

背面

This remote supports four scene controls

Scene 1 : First Button 1-Tap/2-Tap/3-Tap/Held/Released

Scene 2 : Second Button 1-Tap/2-Tap/3-Tap/Held/Released

Scene 3 : Third Button 1-Tap/2-Tap/3-Tap/Held/Released

Scene 4 : Fourth Button 1-Tap/2-Tap/3-Tap/Held/Released

Association Group:

This remote supports 9 Association Group controls

Support group number: 9

Each group max. Support 10 devices

Group 1 Lifeline

Group 2 First button press 1x send basic set 0xff, Second button press 1x send basic

set 0x00.

Group 3 Third button press 1x send basic set 0xff, Fourth button press 1x send basic

set 0x00

Group 4

First button hold more than 0.5s send SWITCH_MULTI-

LEVEL_START_LEVEL_CHANGE(Dim Up)

First button release send SWITCH_MULTILEVEL_STOP_LEVEL_CHANGE

Second button hold more than 0.5s send SWITCH_MULTI-

LEVEL_START_LEVEL_CHANGE(Dim Down)

Second button release send SWITCH_MULTILEVEL_STOP_LEVEL_CHANGE

Group 5

Third button hold more than 0.5s send SWITCH_MULTI-

LEVEL_START_LEVEL_CHANGE(Dim Up)

Third button release send SWITCH_MULTILEVEL_STOP_LEVEL_CHANGE

Fourth button hold more than 0.5s send SWITCH_MULTI-

LEVEL_START_LEVEL_CHANGE(Dim Down)

Fourth button release send SWITCH_MULTILEVEL_STOP_LEVEL_CHANGE

Group 6 First button press 1x to toggle on/off (send basic set 0xff or 0x00).

Group 7 Second button press 1x to toggle on/off (send basic set 0xff or 0x00).

Group 8 Third button press 1x to toggle on/off (send basic set 0xff or 0x00).

Group 9 Fourth button press 1x to toggle on/off (send basic set 0xff or 0x00).

Warranty

Our Products warrants this product to be free from manufacturing defects for a period

of one year from the original date of consumer purchase. This warranty is limited to the

repair or replacement of this product only and does not extend to consequential or

incidental damage to other products that may be used with this product. This warranty

is in lieu of all other warranties, expressed or implied. Some states do not allow

limitations on how long an implied warranty lasts or permit the exclusion or limitation

of incidental or consequential damage, so the above limitations may not apply to you.

This warranty gives you specific rights, and you may also have other rights which vary

from state to state.

FCC / IC

This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s).

Operation is subjected to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC NOTE:

The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modifications to this equipment. Such modifications could void the user’s

authority to operate the equipment.

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

— Consult the dealer or an experienced radio/TV technician for help.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

Important note:

To comply with the FCC RF exposure compliance requirements, no change to

the antenna or the device is permitted. Any change to the antenna or the device could result in the

device exceeding the RF exposure requirements and void user’s authority to operate the device.

C5266091_X10_Ed.2

NIE-TECH CO., LTD

Office of Engineering Technology

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046

Subject: Request for Confidentiality

FCC ID: 2AQURZW924

To Whom It May Concern,

Date: 2021-08-19

to the provisions of Sections 0.457 and 0.459 of Commission's rules

Pursuant

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following

attachment(s) as confidential document from public disclosure.

Exhibits

ID Label/Location

Attestation Statement

External Photos

Block Diagram

Schematics

Test Report

Test Setup Photos

User’s Manual

Internal Photos

Parts List / Tune Up

RF Exposure Info

Operational Description

Cover Letter(s)

SDR Software / Security Info

Long-Term

Confidentiality

No

No

No

☒

☒

No

No

☐ NOTE 1

☐ NOTE 1

☐

No

☒

No

☐

Short-Term

Confidentiality NOTE 2

No

No

☐

☐

☐

No

☐

☐

☐

☐

No

☐

No

No

NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of

KDB 726920, use last in force)

NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant.

Above mentioned document contains detailed system and equipment description are

considered as proprietary information in operation of

the equipment. The public

disclosure of above documents might be harmful to our company and would give

competitor an unfair advantage in the market.

In case of

above are withheld from public view for a period of

Grant of Equipment Authorization and prior to marketing.

short-term Confidentiality, the applicant requests the exhibits selected

days from the date of the

It is our understanding that all measurement test reports, FCC ID label format and

correspondent during certification review process cannot be granted as confidential

documents and those information will be available for public review once the grant of

equipment authorization is issued.

Sincerely,

1/1

C5266091_X10_Ed.2

Signature:

Name:Jianghai Nie

Title:Manager

1/1

Declaration on model difference

We, NIE-TECH CO., LTD, the undersigned hereby confirm that these

models are identical, and all models have the same RF module and Antenna,

except for color of enclosure and model No. for trading purpose.

Product name

S2 Remote Control Switch

Model No.

ZW924,MR40Z

Trade name

Minoston

FCC ID

INPUT

2AQURZW924

DC 3.0V

Confirmed by:

Client’s signature:

Date:2021-08-19

Client’s name / title: Jianghai Nie/Manager

Page 1 of 1

C5266091_X8_Ed.1 Letter of Authorization NIE-TECH CO., LTD Company: NIE-TECH CO., LTD Address: Jilian commercial center 9001, Jinxiu road No.2, Changan Town,Dongguan City, GuangDongProv.,CHINA Product Name: Ourdoor Dimmer Plug Model Number:ZW924,MR40Z We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. is allowed to forward all Name: Jianghai Nie Date: 2021-08-19 Title: Manager Signature of applicant:

1/1