MP31ZD SIZE: 150 x 255 mm 80G 65 x 39 mm Z-Wave Dimmer Plug(800S) MP31ZD Specification Input: 125VAC 60Hz Frequency: 908.42 MHz Loading: 200W Incandescent 100W Dimmable CFL/LED Indoor use in dry location LED indicator Blue: Light status indicator Blue: ADD / Inclusion Purple: Remove / Exclusion Red: Network Failure Program button Press 1x: Manually network. 2. Once the controller is ready to add your device, press the Manual/ Program button on the smart plug 3 times quickly. The blue LED will flash quickly. Now, you have completed control to turn your device ON / OFF according to groups, schedules and interactive automation programmed by your controller. If your Z-Wave certified controller features remote access, you can control your device from your mobile devices. Again: If you have issues with pairing / including, please move the device as close as possible to the hub and try again--you can move to your final location when completed. Note:(1)If the manual button doesn't light up after pressing 3 times, please reset the device: press the button twice quickly then hold a 3rd press for 10 seconds.
(2)The flashing purple light means the device is already paired and also in exclusion mode. If adding fails, please do a z-wave exclusion on your z-wave controller and re-add it. To Remove The Device 1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network. 2. Once the controller is ready to remove your device, press the manual / program button on Features:
hold a 3rd press for 10 seconds To Return The Device To Factory Defaults Reset: Press the button twice quickly then the smart plug 3 times quickly. 1. Z-Wave on / off + dimmer control. 2. Grounded 3-wire power connection for safety. 3. Remember and restore on/off status after power failure. 4. Built-in Z-Wave Plus signal repeater to extend network range 5. S2 security and 800 Z-Wave chip for reliable wireless communication. 6. Work with all certificated Z-Wave controllers. 7. Support Long Range. Min brightness level setting( Refer to Parameter 11) 1: Press the button 5 times quickly, the LED indicator flashes slowly to enter the setting Min brightness mode. The lamp will adjusts to the min brightness automatically. 2: Hold the button to adjust the brightness of the bulb, select the appropriate brightness to set Manual: Press the button twice quickly then hold a 3rd press for 10 seconds. Host reset: Remove it from hub, the device will be restore to factory default. Add QR Code For LR The device is compatible with smartstart. SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code found on the top of the outlet or the back of the box with a controller providing SmartStart inclusion. No furthe action is required and the SmartStart product will be added automaticaly within 10 minutes of being switched on and in the network vicinity. Note:Z- Wave Long Range device can only support be included via SmartStart. Extract the DSK from end device and paste it into the DSK Value in PC Controller, make sure the Long Range' option is ticked. Association Group the min brightness. Group 1 supports 1 node ID,Group 2 Supports maximum of 5 node IDs 3: Press the button 5 times quickly to confirm it (the min brightness setting is completed). Association Group 1: Z-Wave Plus Lifeline The LED indicator will flashes 3 times. Association Group 2: Send Basic Set ON / Off Max brightness level setting( Refer to Parameter 12) Warranty 1: Press the button 10 times quickly, the LED indicator flashes slowly to enter the setting Max Our Products warrant this product to be free from manufacturing defects for a period of one brightness mode. The lamp will adjusts to the max brightness automatically. year from the original date of consumer purchase. This warranty is limited to the repair or 2: Hold the button to adjust the brightness of the bulb, select the appropriate brightness to set replacement of this product only and does not extend to consequential or incidental damage to the max brightness. other products that may be used with this product. This warranty is in lieu of all other warranti-
3: Press the button 10 times quickly to confirm it (the max brightness setting is completed). es, expressed or implied. Some states do not allow limitations on how long an implied warranty The LED indicator will flashes 3 times. lasts or permit the exclusion or limitation of incidental or consequential damage, so the above Remark: If the setting is not confirmed at Step 3, the setting mode will be exited after 10S. limitations may not apply to you. This warranty gives you specific rights, and you may also have Please contact us if you have any questions:
www.newonetree.com ask@newone-tech.com other rights which vary from state to state. Parameter Settings LED Indicator Z-WAVE INTEROPERABILITY This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network. This Device supports Lifeline (association group 1) supporting 1 node for lifeline communication. Group 1 must be assigned the Node ID of the primary controller where unsolicited notifications will be sent. The Z-Wave controller should set this association automatically after inclusion. Lifeline association only supports the Device Reset Locally function. Adding Device To Z-Wave Network for QR CODE Scan here for SmartStar inclusion Note: DSK Code can be found on the This parameter can access you to choose the LED indicator to be on when the plug(light) is on/off, or LED indicator remains on/off all times.
(LED flashes 3 times when the configuration parameter changed.)
--- Parameter =2, size =1byte, Default =0 Value=0 (default) LED is On when switch (light) is Off. Value=1 --- LED is On when switch (light) is On. Value=2 --- LED is always Off. Value=3 --- LED is always On. Auto Turn-Off Timer This parameter can access you to set a timer to make the switch turn off automatically after the switch turns on.The numberentered as value corresponds to number of minutes. Operation: Set up on the hub.
(LED flashes 3 times when the configuration parameter changed.)
--- Parameter =4, Size=4Value: 0 65535(minutes);
packaging box. Value=0(default) disable Do not remove or damage them. Z-Wave Network Configuration Auto Turn-On Timer This parameter can access you to set a timer to make the switch turn on automatically after the switch turned on.The numberentered as value corresponds to number of minutes. Adding Device To Z-Wave Network Operation: Set up on the hub. 1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave
(LED flashes 3 times when the configuration parameter changed.)
--- Parameter =6, Size=4Value: 0 65535(minutes);
Value=0(default) disable turn on the outlet Night Light Set This parameter can access you to set a specific brightness for the light when you want to make it as a night light.
(LED flashes 3 times when the configuration parameter changed.)
--- Parameter =7, Size=1, Default = 2 Value=1 --- 10% brightness
Value=2 --- 20% brightness Value=10 --- 100% brightness Restores state after power failure This parameter can access you to set the switch to be on/off after power failure. Operation: quickly press 8 times to change this parameter.
(LED flashes 3 times when the configuration parameter changed.) Parameter=8Size=1Value=2(default) Value=0 --- The switch is off regardless of the state prior to power failure. Value=1 --- The switch is on regardless of the state prior to power failure. Value=2(default) memory state before power failure This switch will be return to state prior to the power failure after power is restored. Dimmer speed (ON/OFF Control) This parameter can access you to set the time from maximum brightness to minimum brightness or minimum brightness to maximum brightness (Only when turn ON / OFF the light ) Operation: Set up on the hub.
(LED flashes 3 times when the configuration parameter changed.) Parameter=9Size=1, Default = 2 Value=0 --- instant on/off Value=1--- from 0x63 to 0x00 or from 0x00 to 0x63 need 1s Value=2 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 2s
Value=10 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 10s Dimmer speed (Dimmer Control) This parameter can access you to set the time from maximum brightness to minimum brightness or minimum brightness to maximum brightness.
(Only when hold it to change the brightness or control from HUB). Operation: Set up on the hub.
(LED flashes 3 times when the configuration parameter changed.) Parameter=10Size=1, Default = 4 Value=1 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 1s Value=2 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 2s
Value=10 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 10s Multilevel minimum value can be set Operation: quickly press 5 times to change this parameter.
(LED flashes 3 times when the configuration parameter changed.)
---Parameter=11Size=1Default = 10
Value=99 Value=0 --- disable Value=1 Multilevel maximum value can be set Operation: quickly press 10 times to change this parameter.
(LED flashes 3 times when the configuration parameter changed.)
---Parameter=12Size=1Default = 99 Value=0 --- disable Value=1
Value=99 FCC / IC This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s). Operation is subjected to the following two conditions:
(1) This device may not cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such modications could void the users authority to operate the equipment. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Generic Device Class:
0x11-GENERIC_TYPE_SWITCH_MULTILEVEL Specific Device Class:
0x00-SPECIFIC_TYPE_NOT_USED Command Classes:
0x5E-COMMAND_CLASS_ZWAVEPLUS_INFO_V2, Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Important note:
no change to the antenna or the device is permitted. Any change to the antenna or the To comply with the FCC RF exposure compliance requirements, device could result in the device exceeding the RF exposure requirements and void users authority to operate the device. RF warning for Portable device:
The device has been evaluated to meet general RFexposure requirement. The device can be used in portableexposure condition without restriction. CAUTION - PLEASE READ!
This device is intended for installation in accordance with the National Electric Code and local regulations in the United States, or the Canadian Electrical Code and local regulati-
ons in Canada If you are unsure or uncomfortable about performing this installation co-
nsult a qualied electrician. WARNING RISK OF FIRE / RISK OF ELECTRICAL SHOCK / RISK OF BURNS TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS PRODUCT HAS A GROUN-
DING TYPE PLUG THAT HAS A THIRD (GROUNDING) PIN. THIS PLUG WILL ONLY FIT INTO A GROUNDING TYPE POWER OUTLET. IF THE PLUG DOES NOT FIT INTO THE OUTLET, CONTACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER OUTLET. DO NOT CHANGE THE PLUG IN ANY WAY. CONTROLLING APPLIANCES:
CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT DO NOT EXCEED RATINGS DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.) MEDICAL EQUIPMENT Please DO NOT use this switch to control Medical or Life Support equipment. Z-Wave devices should never be used to control the On / Off status of Medical and / or Life Support equipment. CONTROLLING APPLIANCES Please exercise EXTREME CAUTION when using Z-Wave devices to control appliances. Reason being is because the appliance you want to control may be in a separate room and if unintentional behavior occurs (such as adevice turning on or off - either intention-
ally via schedules, or unintentionally via network error) this event may lead to a hazard-
ous condition. For these reasons, please note the following suggestions:
1) Do not include Z-Wave devices in Groups or Scenes if they control appliances. 2) Do not use Z-Wave devices to control electric heaters or any other appliances which may present a hazardous condition due to unattended, unintentional, or automa-
tic power control. 0x86-COMMAND_CLASS_VERSION_V3, 0x26-COMMAND_CLASS_SWITCH_MULTILEVEL_V4, 0x72-COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2, 0x70-COMMAND_CLASS_CONFIGURATION_V4, 0x85-COMMAND_CLASS_ASSOCIATION_V2, 0x5A-COMMAND_CLASS_DEVICE_RESET_LOCALLY, 0x73-COMMAND_CLASS_POWERLEVEL, 0x8E-COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3, 0x9F-COMMAND_CLASS_SECURITY_2, 0x59-COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3, 0x6C-COMMAND_CLASS_SUPERVISION, 0x55-COMMAND_CLASS_TRANSPORT_SERVICE_V2, 0x7A-COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5 0x87-COMMAND_CLASS_INDICATOR