FCC ID: CGJ4156EC Wireless Remote Controller

User Manual Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. The following information must be indicated on the host device of this module;

Contains Transmitter Module FCC ID: CGJ4156EC

[for FCC]

or Contains FCC ID: CGJ4156EC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

*If it is difficult to describe this statement on the host device due to the size, please describe in the user's manual and also either describe on the device packaging or on a removable label attached to the device.

[for ISED]

Contains IC: 4634A-4156EC

[Rated name plate label]

1 / 3 The following statements must be described on the user manual of the host device of this module;

[for FCC]

FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines as this equipment has very low levels of RF energy.

[for ISED]

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1.This device may not cause interference. 2.This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1.Lappareil ne doit pas produire de brouillage;

2.Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. N2012/N1839 has been tested and found to comply with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules. Les connaissances scientifiques dont nous disposons nont mis en vidence aucun problme de sant associ lusage des appareils sans fil faible puissance. Nous ne sommes cependant pas en mesure de prouver que ces appareils sans fil faible puissance sont entirement sans danger. Les appareils sans fil faible puissance mettent une nergie radiolectrique (RF) trs faible dans le spectre des micro-ondes lorsquils sont utiliss. Alors quune dose leve de RF peut avoir des effets sur la sant (en chauffant les tissus), lexposition de faibles RF qui ne produisent pas de chaleur na pas de mauvais effets connus sur la sant. De nombreuses tudes ont t menes sur les expositions aux RF faibles et nont dcouvert aucun effet biologique. Certaines tudes ont suggr quil pouvait y avoir certains effets biologiques, mais ces rsultats n ont pas t confirms par des recherches supplmentaires. N2012/N1839 a t test et jug conforme aux limites d exposition aux rayonnements ISDE nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lISDE. 2 / 3 List of applicable FCC rules This device complies with below part 15 of the FCC Rules. Part 15 Subpart C Limited module procedures Additional testing, Part 15 Subpart B disclaimer Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. 3 / 3

The reason why the rated nameplate label cannot be attached to the module. 10.80.1 Operation control label 17.70.1 Rated nameplate label 1.2 From the figure, it is not possible to attach the process control label and the rated nameplate label at the same time. Therefore, the rated nameplate label is described in the user manual. The character size is limited to 1.2 mm, and if you make it smaller than this, you will not be able to print.

ENVIRONMENTAL & QUALITY ADMINISTRATION QUALITY ASSURANCE DEPARTMENT IMAGING BUSINESS UNIT 2-15-3, Konan Minato-ku, Tokyo Letter of Authorization Date: June 19, 2020 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCC ID

:CGJ4156EC Applicant :Nikon Corporation To whom it may concern:

Thank you for your attention to this matter. Sincerely, Tatsuzo Kudoh Nikon Corporation Please be advised we authorize Shuichi Ohyama of Consumer Technology Division, UL Japan, Inc. to act on our behalf, until otherwise notified, for applications submitted for Federal Communication Commission Radio equipment applications submitted to UL Japan, Inc. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002(b), to the application is subject to denial of federal benefits, that includes FCC benefits. The application for the subject equipment has not been submitted to another TCB for certification.

ENVIRONMENTAL & QUALITY ADMINISTRATION QUALITY ASSURANCE DEPARTMENT IMAGING BUSINESS UNIT 2-15-3, Konan Minato-ku, Tokyo Request for Limited Modular Transmitter Approval June 19, 2020 FCC ID Applicant :Nikon Corporation

:CGJ4156EC This transmitter, model: NC-TRMOD24 is designed by us. It complies with the modular transmitters basic requirements (Item 1 to 8) in FCC Part 15 Subpart C Section 15.212 as indicated below:

Modular Approval Checklist:

Modular approval requirement

(1) Have its own RF shielding.

(2) Have buffered modulation/data inputs.

(3) Have its own power supply regulation. Yes No the antenna and transmission system

(4) Comply with requirements of 15.203, 15.204(b) and 15.204(c).

(5) Tested in a stand-alone configuration. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in FCC 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module. The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available.

(6) Equipped with either a permanently affixed label or must be capable of electronically displaying its FCC ID. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.

(7) Comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.

(8) Comply with any applicable RF exposure requirements in its final configuration: The modular transmitter complies with FCC radiation exposure requirement. Tatsuzo Kudoh Nikon Corporation Since there is no space which indicates FCC ID, FCC ID is not indicated on the label. So FCC ID is indicated in the manual, then the outside of the device into which the module is installed also displays a label referring the enclosed module. to

Request for Confidentiality ENVIRONMENTAL & QUALITY ADMINISTRATION QUALITY ASSURANCE DEPARTMENT IMAGING BUSINESS UNIT 2-15-3, Konan Minato-ku, Tokyo Date: June 19, 2020 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCC ID

:CGJ4156EC Applicant :Nikon Corporation To whom it may concern:

0.457 and 0.459:

Block Diagram Theory of Operation Parts List Schematics Thank you for your attention to this matter. place. Sincerely, Tatsuzo Kudoh Nikon Corporation Please be advised that the following information is to be held confidential based on the FCC rules The application contains technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market

ENVIRONMENTAL & QUALITY ADMINISTRATION QUALITY ASSURANCE DEPARTMENT IMAGING BUSINESS UNIT 2-15-3, Konan Minato-ku, Tokyo Request for Short-Term Confidentiality Date: June 19, 2020 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCC ID

:CGJ4156EC Applicant

:Nikon Corporation To whom it may concern:

Please be advised that the following information is to be held in confidence for 180 days from the date of the Grant of Equipment Authorization based on the FCC rules 0.457 and 0.459:

External Photos Internal Photos Test Setup Photos User Manual The application contains technical information, which we deem to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Sincerely, ____________________________________ Tatsuzo Kudoh Nikon Corporation

KDB996369 Check List Applicable Not Applicable Please refer to User Manual Please refer to LMA Letter and User Manual FCC ID: CGJ4156EC Applicant: Nikon Corporation This transmitter complies with KDB996369 D03 as indicated below:

list compliance frequencies. DO NOT Modular approval requirement 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.10 below concerning the need to notify host manufacturers that further testing is required. 2.3 Summarize the specific operational use conditions Describe use conditions that are applicable to the modular transmitter, including for example any limits on antennas, etc. For example, if point-to-point antennas are used that require reduction in power or compensation for cable loss, then this information must be in the instructions. If the use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturers instruction manual. In addition, certain information may also be needed, such as peak gain per frequency band and minimum gain, specifically for master devices in 5 GHz DFS bands. 2.4 Limited module procedures If a modular transmitter is approved as a limited module, then the module manufacturer is responsible for approving the host environment is used with. The manufacturer of a limited module must describe, both in the filing and in the installation instructions, the alternative means that the limited module manufacturer uses to verify that the host meets the necessary requirements to satisfy the module limiting conditions. A limited module manufacturer has the flexibility to define its alternative method to address the conditions that limit the initial approval, such as: shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation. The alternative method could include that the limited module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host. The module manufacturer must state how control of the product into which the modular transmitter will be installed will be maintained such that full compliance of the product is always ensured. For additional hosts other than the specific host originally granted with a limited module, a Class II permissive change is required on the module grant to register the additional host as a specific host also approved with the module. limited module that the 1 Please refer to User Manual through the change 2.5 Trace antenna designs For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements. a) Information that includes permitted variances (e.g., trace boundary limits, thickness, length, width, shape(s), dielectric constant, and impedance as applicable for each type of antenna);

b) Each design shall be considered a different type (e.g., antenna length in multiple(s) of frequency, the wavelength, and antenna shape (traces in phase) can affect antenna gain and must be considered);

c) The parameters shall be provided in a manner permitting host manufacturers to design the printed circuit (PC) board layout;

d) Appropriate parts by manufacturer and specifications;

e) Test procedures for design verification; and f) Production test procedures for ensuring compliance. The module grantee shall provide a notice that any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify the module grantee that they wish to change the antenna trace design. In this case, a Class II permissive change application is required to be filed by the grantee, or the host manufacturer can take responsibility in FCC ID (new application) procedure followed by a Class II permissive change application. 2.6 RF exposure considerations It is essential for module grantees to clearly and explicitly state the RF exposure conditions that permit a host product manufacturer to use the module. Two types of instructions are required for RF exposure information: (1) to the host product manufacturer, to define the application conditions (mobile, portable xx cm from a persons body); and (2) additional text needed for the host product manufacturer to provide to end users in their end-product manuals. If RF exposure statements and use conditions are not provided, then take responsibility of the module through a change in FCC ID (new application). 2.7 Antennas A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved installer as instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an omni-directional antenna is not considered to be a specific antenna type)). For situations where the host product manufacturer is responsible for an external connector, for example with an RF pin and antenna trace design, the integration instructions shall inform the installer that unique antenna connector must be used on the Part 15 authorized transmitters used in the host product. The module manufacturers shall provide a list of acceptable unique connectors. limited modules, all applicable professional the host product manufacturer is required to 2 Please refer to User Manual Please refer to User Manual Please refer to User Manual 2.8 Label and compliance information Grantees are responsible for the continued compliance of their modules to the FCC rules. This includes advising host product manufacturers that they need to provide a physical or e-label stating Contains FCC ID with their finished product. 2.9 Information on test modes and additional testing requirements Additional guidance for testing host products is given in KDB Publication 996369 D04 Module Integration Guide. Test modes should take into consideration different operational conditions for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. The grantee should provide information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host. Grantees can increase the utility of their modular transmitters by providing special means, modes, or instructions that simulates or characterizes a connection by enabling a transmitter. This can greatly simplify a host manufacturers determination that a module as installed in a host complies with FCC requirements. 2.10 Additional testing, Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part contains 15 unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Subpart B compliant

(when also it 3