FCC ID: 2AQJK-AST-WR070-1 Wireless Power Bank

Mare 8000 mAh Suction Wireless Power Bank Instruction Manual AST-WR070

2.

3.

Wireless Charging Surface Suction Pad USB Output 1 Type-C Input Port USB Output 2 Micro-USB Input Port ON/OFF Button LED Indicators Features:

1. 2. 3. 4. 5. 6. 7. 8. Whats included:

1 x 8000 mAh Wireless Powerbank 1 x USB to Micro-USB Cable 1 x Instruction Manual Battery: 8000mAh/3.7V/29.6Wh USB Output 1/2: 5V/2A Max Wireless Output: 5W Type-C input: 5V/2A Micro-USB Input: 5V/2A LED Indicators ON/OFF Button: Press once to view the remaining power capacity. INSTRUCTIONS:

1.

Charging the Powerbank:

Charge the powerbank fully before usage. Connect the provided charging cable to a power source and to the micro USB port on the powerbank(6). Or your own Type C cable to the Type Input Port (4). Once connected the LED Indicator will HITE when charging, once fully charged LED will turn WHITE. Charging mobile phones and other electronic devices:

Connect the charging cable to your mobile phone/device using the appropriate connector. Connect the USB part of the cable into either USB Output(3 or 5). LED Indicator will illuminate when charging. Remove the USB cable from your mobile device when it is fully charged. Wireless Charging Function:

Press the Powerbank ON/OFF button(7) to turn on the wireless charging function, LED indicator near power button will flash green for one time and turn on. Place wireless charging supported mobile device on the charging surface/suction pad, the green LED will be blinking flash when device is charging. Phone will begin to charge automatically. Note: When wireless charging, if the LED NOT a wireless charging device or there is an object between the device and charging surface interfering with the charging. SAFETY PRECAUTIONS:

WARNING-When using this product, basic precautions should always be followed:

Read all the instructions before use. Never store or use this product in temperatures below 32F (0C) or above 115F (45C). Do not overcharge your phone. The unit may become hot under excessive use. Remove your phone once it is fully charged. Never charge your phone for more than 7 hours at a time. The unit will only achieve full performance after 2 or 3 completed charge and discharge cycles. To reduce the risk of injury, close supervision is required when the product is used near children. Do not expose the device to moisture. Do not use the device in excess of its output rating. Overload outputs above the 1. 2. 3. 4. 5. 6. 7. 8. Do not use the device if damaged or 9. explosion or risk of injury. Do not disassemble the device. For 10. professional. Incorrect reassembly may 11. or temperatures above 104F (40C) may result in explosion. To ensure product safety, ensure that 12. identical replacement parts. Attachments on the back of your phone 13. wireless charger, and lead to overheating. Please remove attachments from the phone before charging on this device. FCC Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.

(1)

(2)

Warning:

approved by the party responsible for compliance could void the users authority to operate the equipment. The distance between user and product should be no less than 20cm. MADE IN CHINA

FCC ID: 2AQJK-AST-WR070-1 Item No.: AST-WR070 Input: DC5V-2A Output: DC5V-2A Wireless Output: DC5V-1A Capacity: 8000mAh 29.6Wh Made In China This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2AQJK-AST-WR070-1 Item No.: AST-WR070 Input: DC5V-2A Output: DC5V-2A Wireless Output: DC5V-1A Capacity: 8000mAh 29.6Wh Made In China This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. 43.5x61mm

January 03, 2020 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen Timeway Testing Laboratories/ Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China. (Name of Agent company name and address) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with NINGBO ALLSTAR O&E TECHNOLOGY CO.,LTD./

NO.19 HUIJIN ROAD,LUOTUO STREET,ZHENHAI, NINGBO, CHINA

<Signature>

NameTeresa Zhong TitleSale CompanyNINGBO ALLSTAR O&E TECHNOLOGY CO., LTD.

January 03, 2020 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AQJK- AST-WR070-1 Product Name: Wireless Power Bank Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

Schematics Block diagram Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors.

<Signature>

NameTeresa Zhong TitleSale CompanyNINGBO ALLSTAR O&E TECHNOLOGY CO., LTD.