FCC ID: 2A3RU-BM1512WB 15 Wireless Control Tubular Motor

SET BUTTON P1 Indicator light Power line Indicator light Up Stop Down K1 Cell 15 Wireless Control Tubular Motor 2 BM151 WB

Direction

1. Match code(power on) Press K1+K1+UP and K1+K1+DOWN within 10s after power up, if the connection is successful the motor will turn. 2. Match code press the set button for 2s, wait for the motor turn prompt once, press P2+P2, if the connection is successful the motor will turn as a prompt. 3. Set journey point Use the transmitter sends the signal K1+UP+K1 to make the motor enter the travel setting state, press stop five times quickly when the motor run to a right position, complete the journey point 1 setup, then run motor to next proper position, press stop five times quickly again,complete the journey point 2 setup, complete all journey point setup. 4. Delete journey point Use the transmitter sends the signal K1+DOWN+K1, clear the journey point. 5. Change run direction Press P1 for 10s, loosen the button after the motor turn prompt three times, run direction changed. 6. Factory reset Press the set button P1 for 15 seconds, the motor will roll 4 times as a prompt, factory reset complete. 7. Adjust speed Use the transmitter sends the signal K1+UP+UP, the speed will increase by one level. Use the transmitter sends the signal K1+DOWN+DOWN, the speed will reduce by one level.

(there are total 3 levels speed: Lv1:25rpm, Lv2:30rom, lv3:35rom) NINGBO BEFUN HOME TECH CO.,LTD FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Consult the dealer or an experienced radio/TV technician for help.

*RF warning for Portable device:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC ID2A3RU-BM1512WB 15 Wireless Control Tubular Motor Model: BM1512WB FCC ID:2A3RU-BM1512WB NINGBO BEFUN HOME TECH CO.,LTD.

C5266091_X10_Ed.1 NINGBO BEFUN HOME TECH CO.,LTD. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2021-11-22 Subject: Request for Confidentiality FCC ID:2A3RU-BM1512WB To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No Short-Term Confidentiality No No No No No No No No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Tom Wang Title: Manager 1/1

NINGBO BEFUN HOME TECH CO.,LTD. C5266091_X8_Ed.1 Letter of Authorization Company:

NINGBO BEFUN HOME TECH CO.,LTD. Address:

No.63 Zhenxing W Rd, Yuyao, Zhejiang, China 315400 Product Name:

15 Wireless Control Tubular Motor Model Number: BM1512WB FCC Identifier: 2A3RU-BM1512WB We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. is allowed to forward all Name:

Tom Wang Date: 2021-11-22 Title:

Manager Signature of applicant:

1/1