Photoelectric And Microwave Motion Sensor Switches BRI816 Instruction Photoelectric And Microwave Motion Sensor Switches BRI816 Instruction BRI816 RC-100 INTRODUCTION The product is a moving object sensor for high bay installation. Its detection range is 50ft,radius is max30ft,and working frequency is 5.8GHz.The advantage of this product is stable working state (stable working temperature:-15~+70C).It offers 4 levels of the light Control : dimming light (0,10%,20%, 30%,optional)--100%--dimming light (0,10%,20%,30%, optional)--off periods of selectable waiting time:motion holdtime, selectable daylight threashold,and freedom of detection ara. SPECIFICATIONS Power supply Maximum load
@ -40F ~ 131F
(-40C ~ 55C) HF System Dim control output Detection radius/angle Mounting height Remote range Time setting Light-control Humidity Temperature 120/277VAC 50/60Hz Resistive/Halogen - 800W/1200W@120/277V Fluorescent Ballast/CFL - 600W/1200W@120/277V Electronic Ballast (LED) - 600/1200VA@120/277V 5.8GHz CW 0-10V, max. 25mA sinking current Max 26.2ft.(8m)/360 Max 50ft. 33ft. (10m) indoor, no backlight 10sec.-30min. (adjustable) 10-2000Lux (adjustable) Max. 95% RH
-104F ~ +158F (-40C ~ +70C)
(15m) SENSORS LED:
1. It always light after switch on power, and be off after the unit enter working state. 2. It flash once when the unit receives sensing signal. DIMENSIONS 98 3.86 37.93 1.49 90 3.54 5 3
. 3 2 2 9
. 0 5 1
. 8 1 1 7
. 0 N I P 4 N I P 5 7 0
. 1 3 2 2
. 1
!
There are nine needles,Pay attention to the direction of insertion!
N I P 5 N I P 4 SENSOR INFORMATION Coverage Side View
'
0 10'
20'
30'
40'
30'
27'
20'
12'
6'
3'
0'
3'
6'
12'
20'
27'
30'
30'
27'
60 ft 20'
12' 6'3'
0' 3' 6'
12'
20'
27'30'
-1-
-2-
30'
20'
12' 6'
0'
6'
12'
20'
30'
Photoelectric And Microwave Motion Sensor Switches BRI816 Instruction Photoelectric And Microwave Motion Sensor Switches BRI816 Instruction WIRING DIAGRAMS BRI816 wiring with dimming ballast or LED driver. Dimming Driver BRI816 wiring with non-dimming ballast or LED driver. Non-Dimming Driver
) e t i h W
(
L A R T U E N LOAD(Red) NEUTRAL(White) l
) k c a B E N I L
(
) e t i h W
(
L A R T U E N LOAD(Red) NEUTRAL(White) l
) k c a B E N I L
(
Dimming Driver Dimming Driver GRAY (-) VIOLET (+) SENSOR MOUNTING Close End Wire Connector BRI816 LED Controller Tightening Nut Sensor module Assembly BRI816 0.2(minimum) Inside Fixture Wall Rubber Gasket Outside Fixture Wall Tightening Nut Rubber Gasket Fixture Wall Tightening Nut sensor module Assembly FUNCTION AND OPTIONS If offers 4 levels of the light Control : dimming light(0,10%,20%, 30%)--100%--dimming light
(0,10%,20%,30%)--off periods of selectable waiting time:motion holdtime and 24hours, selectable daylight threashold,and freedom of detection ara. If natral light lower Light-control setting (10Lux,30Lux,50Lux),the light will not automatically on (0,10%,20%,30%). When person enter in the room,the light will on 100%,after person left the room,the room enter in semi bright brightness after hold on time. With suffcient natural light, the light does not switch on when presence detected. light, With insufficient natural the sensor switches on the light automatically when person options) standby enters the (
The lamp level after the never switch off with presence, even the nature light is sufficient. room. People left,light still dims to 0/10%/20%/30% (options) standby level after the hold time. Light switches off automatically after the dimming time elapsed. OPERATION SETTING BY REMOTE CONTROL ON/
OFF SEND RESET Permanent on or permanent off mode DISP DISPLAY Current Settings The selected parameters go to SEND 100%
5m 100%
20%
+
AUTO TEST 2s Back to previous settings before on/off model In test mode,hold time is only 2s,and stand-by time and daylight sensor are disable. Enter in Adjustable Control Parameters condition and navigate for UP and DOWN OK Confirm settings Navigate for Right and Left The lastest surrounding lux value overites pervious lux value learned. MODE1 MODE2 MODE3 To Save these New Settings parameters as Model 1 Model 2 Model 3 Photocell On/Off,when the light level exceeds this setting, the lights will turn off even when the space is occupied. When light level goes below the settings, the light will turn on even without motion detection. This feature is disabled by default. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.
-3-
-4-