DC1520/DC1522 EmitterSpecification Version NO. : A/00 T Type specification Up button Stop button Down button Setting button Up button Stop button Down button Setting button p1-
p1+
DC1520 Single - channel emitter DC1522 15 - channel emitter DC1520 DC1522 Back side A Additional function Power on A Additional function Power on A Additional function Matchable R tubular motor setting up During the settings,the time between two operation must be shorter than 4s,otherwise it will quit the setting P21 P21 Sound from motor hear long sound Beep once Beep once Delete all the datas of the motor and the new emitter has been programmed. Up1 Run or beep for hint OK Set up is ok. The up button control the motor clockwise Down1 Run or beep for hint OK Set up is ok. The down button control the motor clockwise Matchable DC1680 setting up During the settings,the time between two operation must be shorter than 6s,otherwise it will quit the setting Press (up+down)1 at the same time Indicator flashing Stop1 Indicator long flashing Up1 Indicator flashing then extinguished OK Setting is ok DC1680 DC1680 DC1680 DC1680 DC1680 Matchable DC136 setting up During the settings,the time between two operation must be shorter than 10s,otherwise it will quit the setting Setting button1 Indicator flashing Stop1 Indicator long flashing Up1 Indicator flashing then extinguished T Technical support Power on DC136 DC136 DC136 DC136 DC136 OK Setting is ok Technical specification Fucntion instruction Input voltage3V Transmitting frequency433MHz Transmitting power10 milliwatt Operating temperature-100C500C Transmssion distance200 meters open office 35 meters on two walls DC1522 fifteen channels double control emitter: each channel had the same function with DC1520. One number of LCD screen means one control channel. Press channel choose button P1- (number descending) or P1+ (number increasing) to change the channel. On the analogy of this, loose finger when the indicator light move to suitable channel that you select effective channel. If LCD screen number show 0 that means the group control status. Under the status of group control, pressing a way button will start the group-control function of a way, a way of all the channels will be availabe.Pressing b way buttons will start the group-control function of b way, b way of all the channels will be availabe. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Notice: transmitter do not exposed to moisture and strike, so as not to affect life.When you use transmitter, if found emission distance obviously short or less sensitive, please change another same new battery. Please have batteries for recycling. DC1522 valid channels selection In the setting state,press the up or down button you can quit quickly, if you want to change the valid channels ,reset it. A Additional function
(P1+button+
P1-button)1 P1+button+P1-
button,hold on Press P1+button or P1-button, selecting the channel (channl 1 to channel 15) you need Stop1 The screen will display C The screen will display 15 Or The screen will display o OK Setting is ok FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.