Instruction manual Dimmer Model ED26WF-2US1 ED26WF-US1 It Works with most dimmable LED bulbs and most incandescent bulbs .It have a convenient button that turns lights on and off , also can brighten or dim the bulbs continuously.Using Wi-Fi technology provides an easy,secure way to achieve remote control. LED indicator Operation Install:
Outlet Button Diagram Plug the dimmer into socket of AC power,and attach the load with outlet. TURN ON/OFF:
Tap botton once:lights turn on Tap botton again:lights turn off DIM/BRIGHT:
Hold down botton lights will brighten slowly.When brightness is highest,Hold down botton lights will dim slowly until brightness is lowest. WI-FI:
Turn on the dimmer,then press botton for six times within three seconds (the sixth press should hold on more than 5 seconds),when the LED indicator starts flash and enter into pairing model.Connect app by phone,and control the dimmer. Attention No use outdoor Need dimmable LED light Specifications rated voltage:125V AC, 60Hz Max load: LED 150W; other 300W Manufacturer:
Manufacturer: Ningbo EverFlourish Smart Technology Corp., Ltd. Adress: 77 Wuxiang East Road, Yinzhou, Ningbo, 315111, P.R.China This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution:
This device complies with Part 15 of the FCC Rules / Innovation, Science and Economic Development Canadas licence-exempt RSS(s).Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. MPEReminding TosatisfyFCC/ICRFexposurerequirements,aseparationdistanceof20cmormoreshouldbe maintainedbetweentheantennaofthisdeviceandpersonsduringdeviceoperation. Toensurecompliance,operationsatcloserthanthisdistanceisnotrecommended. L'antenneinstalledoittresitue defaconcequelapopulationnepuisseytreexposeunedistancedemoin de20cm.Installerl'antennedefaconce quelepersonnelnepuisseapprocher20cmoumoinsdelapositioncentraledelantenne. LaFCCdesltatsunisstipulequecetappareildoittreentouttempsloigndau moins20cmdespersonnespendantsonfunctionnement.