FCC ID: VBA-EFNDF5211 Wireless Remote Control Puck Light

Wireless Remote Control Puck Lights INSTRUCTION MANUAL CATALOG NUMBERS EM-BL31W-2pk Thank you for choosing Link2Home!

PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY REASON. If you have a question or experience a problem with your Link2Home purchase, go to http://www.link2home.com If you cant nd the answer or do not have access to the internet, call 1-888-783-6082 from 9 a.m. to 5 p.m. EST Mon.-Fri. to speak with an agent. Please have the catalog number available when you call. SAVE THI S MANUAL FOR FUTURE REFERENCE. 1 Important Safety Guidelines SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Denitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage. DANGER:

WARNING:

CAUTION:

NOTICE:

WARNING: PLEASE READ THIS INSTRUCTION MANUAL THOROUGHLY AND COMPLETELY BEFORE INSTALLATION & USE. FAILURE TO DO SO COULD CAUSE DAMAGE TO PROPERTY, SERIOUS INJURY OR DEATH, AND VOID YOUR WARRANTY. WARNING:CancerandReproductiveHarm-

www.P65Warnings.ca.gov. AVERTISSEMENT: Cancer et Troubles de l'appareil reproducteur -

www.P65Warnings.ca.gov. ADVERTENCIA:CnceryDaoReproductivo-

www.P65Warnings.ca.gov. For California residents / Pour les rsidents de la Californie / Para residentes en California 2 Wireless Remote Control Puck Lights Table of Contents Table of Contents......................................3 Operation.................................................7 Safety Information....................................3 Care and Cleaning ..................................7 Pre-Installation ..........................................5 Warranty...................................................8 Installation..................................................6 Safety Information Consult a qualied electrician if you have any electrical questions. NOTE: This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Be cautious of what surface the mounting disc is attached to, as it may remove paint or damage surface. BATTERY PRECAUTIONS Use only the size and type of batteries specied. Always purchase the correct size and grade of battery most suitable for the intended use. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries. Replace all batteries of a set at the same time. Do not mix old and new batteries. Clean the battery contacts and also those of the device prior to battery installation. Do not dispose of batteries in re. Remove batteries if consumed or if product is to be left unused for an extended period of time. WARNING: Modications to this product not approved by the party responsible for compliance could void the users authority to operate the product. 3 Wireless Remote Control Puck Lights Remote Battery Replacement:

If operation of the receiver units becomes erratic, it may be necessary to replace the battery in the hand-held remote unit. To do this, rst remove the battery compartment cover. Press the tray release button on the back of the remote. Next, remove the depleted battery and discard according to local ordinances. Be sure to correctly install the new battery. Replace battery compartment cover and test by using it to control the indoor remote control outlets. 1. Appliances to be connected to the remote control socket MUST NOT exceed the voltage and current ratings as in Specications. 2. Operation is subject to the following two conditions:

(1) this appliance may not cause harmful interference, (2) this appliance must accept any interference received, including interference that may cause undesired operation. 3. Only for indoor use and storage. 4. Low transmitter battery may lower the distance between the transmitter and the receiver. FCC PART 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may cause harmful interferenceand

(2) this device must accept any interference receivedincluding interferences that may cause undesired operation Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates,uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected Consult the dealer or an experience radio/TV technician for help. 4 Wireless Remote Control Puck Lights Pre-Installation PLANNING INSTALLATION Read all instructions before assembly. To avoid damaging this product, assemble it on a soft, non-abrasive surface, such as carpet or cardboard. Keep your receipt and these instructions for proof of purchase. PRODUCT DATA Bulb type:3*2835 SMD Luminance:40lm Battery:3*1.5V AAA(not incl.) Electricity:110mAh,Voltage:4.5V Function:Multi-function Remote control distance:39ft Remote: Ground color is light grey(not dark grey) Lens color: Smoky white PACKAGE CONTENTS A B REMOTE CONTROL POWER TIMER DIMMER DIMMERPRESETS Description Part A B Light xture3 AAA batteries NOT included Remote (CR2032 button cell battery and insulation piece preinstalled ) Quantity 8 2 5 Wireless Remote Control Puck Lights Installation 1. Replacing the batteries If the LEDs appear to be dim, this is an indication that your batteries need to be replaced. Rotate the battery cover counterclockwise and remove it. Remove the old batteries and insert three new AAA batteries. Be sure to match the polarity as shown in the diagram in the battery compartment. Check light operation to conrm that batteries are correctly installed. Replace the battery cover and rotate it clockwise to lock it in place. CAUTION: Do not mix battery types. Use only fresh batteries. Alkaline are recommended. 2. Mounting with double-sided tape Check the location of where you want to place the puck light. Make sure it is clean and that there is no debris or dust. Remove the protective lm from one side of the double-sided tape (BB) and apply to the center of the mounting bracket (battery door). Peel o the remaining protective lm and press the mounting bracket rmly to the intended surface for 5 seconds. CAUTION: Be cautious of what surface the double-sided tape is attached to, as it may remove paint or damage the surface. REMOTE BATTERY 1 CR2032 button cell(incuded) SAFETY INSTRUCTION BATTERY WARNINGS DO NOT mix old and new batteries DO NOT mix alkaline standard(carbon-zinc),or rechargeable(NH-CD,NI-MH,etc) batteries This product contains a button battery If swallowed,it could cause severe injury or death in just2 hours.Seek medical attention immediately. 6 Wireless Remote Control Puck Lights Operation 1. Install batteries Install batteries and close the batteries cover in place 2. Turning the light on Press once to turn ON . Pressing again to OFF 3. Using the Remote REMOVE THE INSULATION PIECE FIRST REMOTE CONTROL POWER:

Controls all puck lights RED: Turn ALL puck lights o GREEN: Turn ALL puck lights on TIMER Controls the amount of time the puck lights will stay ON. Turn lights ON rst then select duration. Lights will ash once to conrm command and timer clears when lights turn OFF(10,30,60 or 120 minutes) DIMMER Controls brightness of all puck lights Press and hold(+) to increase brightness Press and hold(-) to decrease brightness DIMMERPRESETS Turn lights ON rst then select brightness preset(10%,40%,80% or 100% brightness) LAST MEMORY All puck lights will return to the prior brightness settings when turned ON. Care and Cleaning REMOTE CONTROL POWER TIMER DIMMER DIMMERPRESETS NOTE: The remote uses RF technology and does not need to be aimed at the puck light Clean the lamp with a soft, dry cloth. Do not use any cleaners with chemicals, solvents, or harsh abrasives. 7 Wireless Remote Control Puck Lights LINK2HOME 1 YEAR LIMITED WARRANTY IMPORTANT: Proof of Purchase is required to obtain warranty service Paragon Group USA Inc. warrants to the original owner that our products will be free from defect in workmanship and material for a period of ONE YEAR from the date of purchase. Should any unit(s) prove to be defective during this period, Paragon Group USA Inc. will be responsible for replacement of the defective unit(s) only. Paragon Group USA Inc. is not responsible for labor charges or any incidental or consequential expenses. Not Covered Batteries are not covered by this warranty. Repair service, adjustment and calibration due to misuse, abuse or negligence are not covered by this warranty. Unauthorized service or modication to this product or of any furnished components will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, set-up time, loss of use, postage, unauthorized service, or other products used in conjunction with Link2Home products. For warranty service, please contact Paragon Group USA Inc. Customer Service by Phone: 1-888-783-6082 or e-mail: info@paragongroupusa.com. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state. Paragon Group USA Inc. Link2Home Product Division Englewood, NJ 07631 USA link2home.com 8

Ningbo EverFlourish Smart Technology Corp.,Ltd Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: VBA-EFNDF5211 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram Schematics Operational Description File Name Block Diagram Schematics Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, We also requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after the Grant Date of Equipment Authorizations. File Name User manual Internal photos Setup photos Exhibit Type User manual Internal photos Setup photos Sincerely, James Zhu Rev 11/20/07

Ningbo EverFlourish Smart Technology Corp.,Ltd Declaration on model difference Wetheundersignedherebyconfirmthatthesemodelsareidentical,andallmodelshavethe sameRFmoduleandantenna,PCBlayout,schematicsandcomponent.Onlydifferentonmodel number. Productionname Trademark FCC Modelno. WirelessRemote ControlPuckLights VBAEFNDF5211 NDF5211,EMBL31W, EMBL31W2pk

, Confirmed by:

JamesZhu 2021/11/10

Ningbo EverFlourish Smart Technology Corp.,Ltd Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2021/11/10 SUBJECT: FCC Application for (FCC ID:VBA-EFNDF5211) To Whom It May Concern:

We, the undersigned, hereby authorize Sam Lv at EMTEK(DONGGUAN) CO., LTD.on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by EMTEK (DONGGUAN) CO., LTD.on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, James Zhu 2021/11/10