Quick Start Guide to Lynguide til En snabbguide till Kurzanleitung fr EN 2 EN 5 EN 8 EN Quick Start Guide to 1-12 DK Lynguide til 13-23 SE En snabbguide till 24-34 DE Kurzanleitung fr 35-45 EN 3 EN 1 EN 4 Remove back cover by unscrewing the 2 screws. Insert Batteries Insert the 2 provided AAA batteries. Make sure batteries are in the proper +/- orientation!
Replace the back cover. Place the sensor in the meat to or through the marking on the sensor. Place the sensor at the thickest place in the meat. Important not to penetrate the meat. EN 6 Guidance for placement of sensor EN 7 Place the sensor from top and deep into the meat without penetrating the meat. For smaller piece of meat place the sensor in lower angle in meat. For very thin piece of meat horizontal placement is also possible. When sensor is placed through the meat you are always guaranteed to measure the core temperature of meat
(which is not necessarily in the center of the meat).
- Find more user tips at www.cookperfect.com/support WARNING:In a BBQ it is strongly recommended to avoid closing the Lid and using direct heat when sensor is horizontal placed in a thin piece of meat. This is due to heat radiation that can cause temperatures of sensor to exceed much higher temperature than 300C
(662F) even if air temperature is much less. Go to www.cookperfect/support to get more information including videos on how to use the CookPerfect App. Read the instruction manual carefully before use. The appliance is not to be used by children or persons with reduced physical,sensory or mental capabilities,or lack of experience and knowledge,unless they have been given supervision or instruction. Children should be supervised and instructed not to play with the appliance. Sensors can only be cleaned by hand wash.
and burning of the sensors. The sensor is not to be used in water or liquids. The sensor maximum temperature is 300C (662F). Temperatures above limit may damage the sensor . DO NOT immerse the receiver in water or liquids in general. DO NOT put the receiver in a microwave, Ovens, grills and other heating elements. Operation is subject to the following two conditions:
( 1 )this device must not cause interference,and
( 2 )this device must accept any interference, including interference that may cause undesired operation of the device. EN 10 EN 12 EN 9 Product Overview
following accessory comply with all pertinent and essential requirements as per the EU directive /5/E. Sensor Sensor LED Center LED Magnetic Base Batteries Battery Cover Holder for sensor EN 11 FCC Warning Statement Phases:
Receiver wakes up by connecting the intelligent meat thermometer. ( full awake for 2min. ) If receiver enter Sleep-mode ( thermometer is still plugged into the receiver ), the receiver will look for mobile device one-time for each minute ( blue
If no sensor is connected to the receiver, the receiver never looks for mobile device. The cookperfect calculates when the meat will be ready to be served. The calculation of Time when
your cooking activity!
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Center LED:
Flashing blue:The receiver is in pairing mode
- will look for mobile device in 2 min,before entering Sleep-mode.
Solid Blue:The receiver is paired to a mobile device. Connector LED:
green:Thermometer is detected.
Fast blinking green:The target temperature is<5 away.
Solid green:Target temperature has been reached.
party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.