FCC ID: 2BEKN-HEATER Space Heater

Space Heater INSTRUCTION MANUAL MODEL:HEATER-WIFI IMPORTANT INSTRUCTIONS PLEASE READ AND SAVE THESE IMPORTANT SAFEGUARDS To ensure the best performance from your heater, please read and save the following instructions WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS INCLUDING THE FOLLOWING:

Read all instructions before using this heater. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials such as drapes, furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them at least 1 foot ( 0.3m) the sides and rear of the heater. Extreme caution is necessary when any heater is used by or near children or invalids,and whenever the heater is left operating and unattended. Always unplug heater when not in use. Do not operate any heater with a damaged cord or plug, or after the heater malfunctions or has been dropped or damaged in any manner. Discard t h e heater or return the heater to authorized service facility for examination and/or repair. Do not use in outdoors. Never locate heater where it may fall into a bathtub or other water container. Do not run cord under carpeting. Do not cover cord with rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over. To disconnect the heater, to control to OFF then remove plug from outlet. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the heater. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons. Always plug heater directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip). 1 Never tamper with this product or attempt to fix it. Any tampering with, or modification of this heater can result in serious injury, death, or fire. Risk of electric shock. Do not open. No user serviceable parts inside. This heater is not intended for use by persons (including children)with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. If your home has aluminum wiring, you will need a licensed electrician to check your receptacles connections.When using a 1500-watt heater, aluminum wire connections may cause a safety issue. Before cleaning or storage, turn the products controls to the OFF position and disconnect the heater from the electrical outlet and allow it to cool. 2 INSTALLATION The heater must be installed on a wall before operating. Dont try to use it without installation. The installation sequence of the fan heater is as follows:

1. Find a space to install the fan heater. 2. Drill two holes of the dimension of the expansible tubes - 8 mm - in the wall

(See Figure ) - D= 172mm 3. Insert the expansible tubes into the holes and tighten them with the screws provided firmly. NOTE: Fasten the screws tightly. Do not fasten the screw into the expansible tube thoroughly; the length of the bare parts should be 10 mm. 4. Mount the fan heater to the wall . Make sure the two holes located on the back of the heater do aim at the above two screws, then push the heater backwards to the wall, and then downwards till the unit is stable. Hanging Hole Dimension : 172mm Main OF/OFF Switch Window inlet Window outlet 2 The Control Panel and Display Timer/

WIFI Reset Mode Remote Control Timer Temperature Control WIFI Reset ON/OFF Mode 3 OPERATIONS Control Panel Operation P ress th e ON -O FF switch at the rig h t sid e o f th e un it to switch th e app liance ON (I) o r O FF ( O ) P ress at th e first time to en ter th e mo d e o f fan o n ly

- P ress ag ain to the lo w p o wer mo de

- P ress at the th ird time to th e h igh p o wer mo de

- P ress at th e fo u rth time, th e heater en ters in to the stan db y mo d e ( th e fan will ru n fo r 30 seco nd s and th en tu rn o ff ) P ress th e bu tton to set th e timer (Fro m0 ho ur - 24 ho u rs). E ach time yo u p ress the b u tto n ad d s an h ou r to th e timer. T he d isp lay will sh o w cu rren t settin g time fo r 5 second s after setting , the resu me th e p revio u s d isp lay an d th e lig h t tu rn s o n. P ress th e o n the con tro l p anel fo r 3 seco nd s is to reset th e WIFI. T h e un it will b e d iscon n ected fro m yo u r d evice. Remote Control Operation P ress to tu rn on o r o ff th e h eater P ress to select the mo de o f fan on ly lo w p o wer an d h ig h p ower P ress to set the timer (Fro m0 ho u r - 24 ho u rs). On e p ress of th e bu tto n ad ds an ho ur to th e timer. T h e d isp lay will sh o w cu rren t setting time fo r 5 seco n ds afte r settin g , th e resu me th e previou s d isp lay an d th e tu rn s on . lig h t P ress

to ad just th e rmo stat co n tro l. Temperatu re settin g fro m 4 5 0 -9 5 d eg ree. T h e b u tto n o f is to in crease the d esire d temp eratu re an d is to d ecrease it. P ress to reset the WIFI. T he u n it will b e d isconn ected fro m yo u r device. Battery The remote control requires 1 CR2025 3V lithium battery (not included) Important: Follow the instructions of use and the recycle rules given on the battery packaging. 1- Open the battery compartment by sliding the cover down. 2- Insert the battery into the compartment, observing the polarity in the diagram (see below drawing). 3- Close the battery compartment. Smart Heater Operation with WIFI USE YOUR SMART HEATER 1. Download Tuya App by scanned the QR code below. Or search Tuya in the Apple App Store (iOS devices) or Google Play Store (Android devices). 2 . Tu rn on yo u r smartp hon e s B luetoo th ( at th e first time u se) an d en sure yo u r p h on e was co nn ected th e same W IFI as th e h eater. 3 . Op en the Tu ya Ap p, tap Ad d D evice to search P TC -SH 01 5 4 . Tap th e d evice ico n an d co mp lete p airing with fo llo wing th e o n -screen in structio ns NOTE:

1 ) E nsu re you r sma rtpho ne s B lue too th is turn ed o n ( a t the fi rs t time u se ) an d you r ph on e wa s co nn ec te d the s ame W IFI as the he a te r wh ile yo u pa i rin g th e u ni t. 5 2 ) Onl y o ne d e vi ce ca n b e pai re d the uni t whe n usi ng . Th e W IFI mu s t be re se t o r the uni t m us t be del e te d in the Tu ya A pp if yo u wan t to re pla ce the co nne c ted de vi ce . 3) Choose to Allow all permissions when using Tuya App for the first time. This app will not record your personal device use. 4) This unit has memory function, only for settings of temperature and mode. The Timer setting or Weekly Program setting will as long as switch ON or Stand by. If main switch OFF, power cut off, or plug out, it needs to reset. You can check your settings in the App. OVERHEAT PROTECTON 1 . A thermal overload protector is built in at the top of the heating panel, if the heater is obstructed or blocked at front panel and rear ventilation panel by the curtain, drape or cotton sheet etc., the thermal overload protector activates to prevent overheat. 2. When the internal temperature of the heater reaches up to 158 which may cause fire hazard, the heater will be shut off automatically. It can ONLY resume operation when the user resets the unit. To Reset Heater:

1. Unplug the heater and wait about 15 minutes until the heater cooling down. 2 . After the heater has cooled down, plug the unit into a 110- 120V electrical outlet again and follow the operation instructions described in this manual. MAINTENANCE AND CLEANING

- Warning : Never use detergent, chemical damage plastic parts.

- WARNING : Let the appliance cool down completely before handling or cleaning.

either with or without soap.

- Regularly clean the air inlet and outlet vents of the fan. To prevent risk of fire or electrocution inside the appliance. Clean the outside wall of the appliance by rubbing it gently with soft, damp cloth, SPECIFICATIONS Model Rating Power Power Waterproof HEATER-WIFI 1500W 120V ~ 60Hz IPX2 6 USE YOUR SMART HEATER Download Tuya App by scanned the QR code or searched Tuya in the Apple App Store (iOS devices) or Google Play Store (Android devices). This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

C5266091_X24_Ed.2 Attestation Statements TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules for covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) that prohibit equipment authorization Applicant Company name: ningbozhuoyourunmaoyiyouxiangongsi Grantee code: 2BEKN FCC ID: 2BEKN-HEATER FRN: 0034757856 Contact Name: Snake zhang Address: cixi lvsenongchanpingjiagongjidi lvyuanyilu No.255 ningbo zhejiang 315300 E-mail: 498124721@qq.com Telephone: 13410067442 Fax: 13410067442 i. ii.

[ningbozhuoyourunmaoyiyouxiangongsi] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification.

[ningbozhuoyourunmaoyiyouxiangongsi] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification.

[ningbozhuoyourunmaoyiyouxiangongsi] (the applicant) certifies that, as of the date of the filing of the application, the applicant [ is not] identified on the Covered List as an entity producing coveredequipment . Date: 2024/01/15 Applicants Name: Snake zhang Title: Manager Signature 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

cixishipainuodianqiyouxiangongsi Date: 2024-01-15 Federal Communications Commission To Whom It May Concern:

The letter grants authorization for representative of _ ningbozhuoyourunmaoyiyouxiangongsi __ to apply the FCC for a change in identification. This authorization applies to _ cixishipainuodianqiyouxiangongsi _, FCC ID: _ 2BDOS-WARMLREC _, granted on _11/27/2023 __. The equipment is electrically identical. The only applicant name address, manufacturer name address, model name, trade name, and FCC ID differ.. The original test results, technical information and relevant documents continue to be representative of and applicable to the changed equipment. Should there be any question, please feel free to contact us. Sincerely, Signature:

Name: Snake Zhang Title: Manager Company Name: cixishipainuodianqiyouxiangongsi Company Address: cixi lvsenongchanpingjiagongjidi lvyuanyilu No.255 ningbo zhejiang 315300 Page 1 of 1

ningbozhuoyourunmaoyiyouxiangongsi C5266091_X4_Ed.1 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject:

Request for 2.933 Change in identification of equipment Reference:

FCC ID: 2BDOS-WARMLREC (new ID: 2BEKN-HEATER) Date: 2024-01-15 Gentlemen,

(ningbozhuoyourunmaoyiyouxiangongsi) requests a Change in Identification for a currently approved device. This application will establish a new FCC ID for purpose of marketing. The original Grant for (cixishipainuodianqiyouxiangongsi), under FCC ID: 2BDOS-WARMLREC with a Grant Date of (11/27/2023) will remain in effect. An authorization letter from the original Grantee is attached. We attest that the equipment is electrically identical. Only applicant name address, manufacturer name address, model name, trade name, and FCC ID differ. The original test results are applicable and continue to be representative of this device. The following files are provided as attachments:

Cover letter giving permission from original Applicant for Change in ID External photos showing no physical changes to this device New FCC identification label and its location. Thanks and Best Regards, Name: Snake Zhang Title: Manager Company Name: ningbozhuoyourunmaoyiyouxiangongsi Company Address: 1haolou11-4shi-3gutangjiedaocixizhihuigukejiguangchangcixi zhejiang315300 1/1

ningbozhuoyourunmaoyiyouxiangongsi Product Similarity Declaration Company: ningbozhuoyourunmaoyiyouxiangongsi Address: 1haolou11-4shi-3gutangjiedaocixizhihuigukejiguangchangcixi zhejiang315300 Product Name: Space Heater Model Number: HEATER-WIFI yushiqunuan-wf, HEATER-BLACK, HEATER-WHITE, HEATER-SILVER, HEATER-WIFI-

BLACK, HEATER-WIFI-WHITE, HEATER-WIFI-SILVER FCC Identifier: 2BEKN-HEATER We (ningbozhuoyourunmaoyiyouxiangongsi ) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), same mechanical structure and design (including product enclosure, materials, etc.,), the only difference is the model name and appearance color. Clients signature Name: Snake Zhang Date: 2024-1-15 Title: Manager Signature of applicant:

ningbozhuoyourunmaoyiyouxiangongsi Letter of Authorization Company: ningbozhuoyourunmaoyiyouxiangongsi Address: 1haolou11-4shi-3gutangjiedaocixizhihuigukejiguangchangcixi zhejiang315300 Product Name: Space Heater Model Number: HEATER-WIFI yushiqunuan-wf, HEATER-BLACK, HEATER-WHITE, HEATER-SILVER, HEATER-WIFI-BLACK, HEATER-WIFI-WHITE, HEATER-WIFI-SILVER FCC Identifier: 2BEKN-HEATER We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Snake Zhang Date: 2024-01-15 Title: Manager Signature of applicant:

1/1

US Agent for Service of Process LETTER OF ATTESTATION TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process:

Company Name: UGK-LVMUNITEDINC FRN: 0033476375 Contact Name:

Address: 6547NAcademyBlvd#2266,ColoradoSprings,CO80918 Telephone No:

Email:

001-323-51 04660 ugk-lvm@hotmail.com Jimmychen Applicant:

Company name: ningbozhuoyourunmaoyiyouxiangongsi Grantee code: 2BEKN FCC ID: 2BEKN-HEATER FRN: 0034757856 Contact Name: Snake zhang Address: cixi lvsenongchanpingjiagongjidi lvyuanyilu No.255 ningbo zhejiang 315300 E-mail: 498124721@qq.com Telephone: 13410067442 Fax: 13410067442

[ningbozhuoyourunmaoyiyouxiangongsi] certifies that, as of the date of this filing of the application with the TCB, [UGK-LVMUNITEDINC] is our designated US agent for service of process for the above referenced FCC ID.

[ningbozhuoyourunmaoyiyouxiangongsi] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [UGK-

LVMUNITEDINC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. Date: 2024/01/15 Applicants Name: Snake zhang Title: Manager Signature US Agents Name: Jimmychen Title: Manager Signature 1/1