FCC ID: 2ADZRG2426GA 7368 ISAM ONT

7368 Intelligent Services Access Manager ONT G-2426G-A Product Guide 3FE-XXXXX-AAAA-TCZZA Issue 1 September 2020 Nokia Proprietary and Confidential Use pursuant to applicable agreements D r a f t D r a f t 7368 ISAM ONT t f a r D Legal notice 2020 Nokia. Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners. The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein. Contains proprietary/trade secret information which is the property of Nokia and must not be made available to, or copied or used by anyone outside Nokia without its written authorization. Not to be used or disclosed except in accordance with applicable agreements. t f a r D 2 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Contents Contents 7368 ISAM ONT D r a f t About this document............................................................................................................................................7 1 ETSI ONT safety guidelines ........................................................................................................................13 Safety instructions.............................................................................................................................13 Safety standards compliance ............................................................................................................15 Electrical safety guidelines................................................................................................................15 ESD safety guidelines .......................................................................................................................16 Laser safety guidelines .....................................................................................................................16 Environmental requirements .............................................................................................................20 2 ETSI environmental and CRoHS guidelines ..............................................................................................21 Environmental labels.........................................................................................................................21 Hazardous Substances Table (HST) .................................................................................................23 Other environmental requirements....................................................................................................23 3 ANSI ONT safety guidelines........................................................................................................................25 Safety instructions.............................................................................................................................25 Safety standards compliance ............................................................................................................27 Laser safety guidelines .....................................................................................................................29 Electrical safety guidelines................................................................................................................32 ESD safety guidelines .......................................................................................................................33 Environmental requirements .............................................................................................................33 4 G-2426G-A unit data sheet ..........................................................................................................................35 Overview ...........................................................................................................................................35 G-2426G-A part numbers and identification......................................................................................35 G-2426G-A general description.........................................................................................................37 G-2426G-A software and installation feature support .......................................................................43 G-2426G-A interfaces and interface capacity ...................................................................................43 G-2426G-A LEDs ..............................................................................................................................45 G-2426G-A detailed specifications....................................................................................................47 G-2426G-A GEM ports and T-CONTs ...............................................................................................48 G-2426G-A performance monitoring statistics ..................................................................................48 G-2426G-A functional blocks ............................................................................................................50 G-2426G-A standards compliance ....................................................................................................51 G-2426G-A special considerations....................................................................................................53 1.1 1.2 1.3 1.4 1.5 1.6 2.1 2.2 2.3 3.1 3.2 3.3 3.4 3.5 3.6 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 3 7368 ISAM ONT Contents t f a r D 5 Install a G-2426G-A indoor ONT..................................................................................................................55 Overview ...........................................................................................................................................55 Purpose.............................................................................................................................................55 General .............................................................................................................................................55 Prerequisites .....................................................................................................................................55 Recommended tools .........................................................................................................................55 Safety information .............................................................................................................................56 Procedure..........................................................................................................................................56 6 Replace a G-2426G-A indoor ONT ..............................................................................................................61 Overview ...........................................................................................................................................61 Purpose.............................................................................................................................................61 General .............................................................................................................................................61 Prerequisites .....................................................................................................................................61 Recommended tools .........................................................................................................................61 Safety information .............................................................................................................................62 Procedure..........................................................................................................................................62 7 Configure a G-2426G-A indoor ONT ...........................................................................................................67 7.1 Overview ...........................................................................................................................................67 GUI configuration.........................................................................................................................................70 General configuration........................................................................................................................70 HGU mode GUI configuration ...........................................................................................................70 Log in to the web-based GUI ............................................................................................................70 Viewing device information and connection status .................................................................................72 Overview ...........................................................................................................................................72 Viewing device information................................................................................................................72 Viewing LAN status ...........................................................................................................................74 Viewing WAN status..........................................................................................................................76 Viewing WAN IPv6 status..................................................................................................................78 Viewing home networking information...............................................................................................80 Viewing Optics module status ...........................................................................................................82 Viewing statistics ...............................................................................................................................84 Viewing voice information..................................................................................................................86 Network configuration .................................................................................................................................89 Overview ...........................................................................................................................................89 Configuring LAN................................................................................................................................89 Configuring LAN IPv6........................................................................................................................92 5.1 5.2 5.3 5.4 5.5 5.6 5.7 6.1 6.2 6.3 6.4 6.5 6.6 6.7 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 7.15 7.16 t f a r D 4 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Contents 7368 ISAM ONT 7.17 7.18 7.19 7.20 7.21 7.22 7.23 7.24 7.25 7.26 7.27 7.28 7.29 7.30 7.31 7.32 7.33 7.34 7.35 7.36 7.37 7.38 7.39 7.40 7.41 7.42 7.43 7.44 7.45 7.47 7.48 7.49 Configuring WAN...............................................................................................................................93 Configuring WAN DHCP ...................................................................................................................95 Configuring Wireless 2.4GHz............................................................................................................97 Configuring Wireless 5GHz.............................................................................................................100 Configuring wireless scheduling......................................................................................................103 Configuring IP routing .....................................................................................................................105 Configuring DNS .............................................................................................................................107 Configuring TR-069 .........................................................................................................................109 Configuring GRE tunnel ..................................................................................................................110 Configuring Upstream (US) Classifier ............................................................................................112 Configuring QoS..............................................................................................................................119 Security configuration ...............................................................................................................................123 Overview .........................................................................................................................................123 Configuring the firewall....................................................................................................................123 Configuring the MAC filter ...............................................................................................................124 Configuring the IP filter....................................................................................................................126 Configuring the URL filter ................................................................................................................128 Configuring parental control ............................................................................................................129 Configuring DMZ and ALG ..............................................................................................................131 Configuring access control..............................................................................................................133 Configuring the Application ......................................................................................................................136 Overview .........................................................................................................................................136 Configuring port forwarding.............................................................................................................136 Configuring port triggering...............................................................................................................138 Configuring DDNS...........................................................................................................................140 Configuring NTP..............................................................................................................................142 Configuring USB .............................................................................................................................143 Configuring UPnP and DLNA ..........................................................................................................145 Configuring voice ............................................................................................................................146 Maintenance ...............................................................................................................................................149 Overview .........................................................................................................................................149 Configuring the password ...............................................................................................................149 7.46 WAN speed test ..............................................................................................................................151 Speed test history ...........................................................................................................................152 Configuring LOID ............................................................................................................................154 Configuring SLID.............................................................................................................................155 7.50 Managing the device .......................................................................................................................156 September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t D r a f t 5 Contents t f a r D 7368 ISAM ONT Backing up the configuration...........................................................................................................158 Restoring the configuration .............................................................................................................159 Upgrading firmware.........................................................................................................................160 Rebooting the device ......................................................................................................................161 Resetting to factory defaults............................................................................................................162 Diagnosing WAN connections.........................................................................................................163 Viewing log files ..............................................................................................................................164 RG Troubleshooting Counters..................................................................................................................167 Overview .........................................................................................................................................167 Viewing Residential Gateway (RG) troubleshooting counters.........................................................167 8 ONT configuration file over OMCI ............................................................................................................171 Overview .........................................................................................................................................171 Purpose...........................................................................................................................................171 Supported configuration file types...................................................................................................171 ONT configuration file over OMCI ...................................................................................................174 7.51 7.52 7.53 7.54 7.55 7.56 7.57 7.58 7.59 8.1 8.2 8.3 8.4 t f a r D 6 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 About this document 7368 ISAM ONT About this document Purpose This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures of this ONT for the current release. Intended audience Safety information This documentation set is intended for planners, administrators, operators, and maintenance personnel involved in installing, upgrading, or maintaining the ONTs. The reader must be familiar with general telecommunications principles. For your safety, this document contains safety statements. Safety statements are given at points where risks of damage to personnel, equipment, and operation may exist. Failure to follow the directions in a safety statement may result in serious consequences. Safety Information Examples Danger indicates that the described activity or situation may result in serious personal injury or death; for example, high voltage or electric shock hazards. Warning indicates that the described activity or situation may, or will, cause equipment damage or serious performance problems. DANGER Hazard WARNING Equipment Damage CAUTION Service Disruption Caution indicates that the described activity or situation may, or will, cause service interruption. Note:A note provides information that is, or may be, of special interest. Acronyms and initialisms The expansions and optional descriptions of most acronyms and initialisms appear in the glossary September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t D r a f t 7 About this document 7368 ISAM ONT t f a r D Nokia quality processes Nokias ONT manufacturing, testing, and inspecting practices are in compliance with TL 9000 requirements. These requirements are documented in the Fixed Networks Quality Manual 3FQ-

30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met. The customer or its representatives may be allowed to perform on-site quality surveillance audits, as agreed upon during contract negotiations. Documents Documents are available using ALED or OLCS. To download a ZIP file package of the customer documentation Navigate to http://customer.nokia.com/s/ and enter your user name and password. If you are a new user and require access to this service, please contact your Nokia sales representative. Select Products. Type your product name in the Find and select a product field and click the search icon. Select a product. Click Downloads: ALED to go to the Electronic Delivery: Downloads page. Select Documentation from the list. Select a release from the list. 1 2 3 4 5 6 7 Follow the on-screen directions to download the file. END OF STEPS To access individual documents Individual PDFs of customer documents are also accessible through the Nokia Support Portal website. t f a r D 8 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 About this document 7368 ISAM ONT 1 2 3 4 5 6 1 2 Navigate to http://customer.nokia.com/s/ and enter your user name and password. If you are a new user and require access to this service, please contact your Nokia sales representative. Select Products. Type your product name in the Find and select a product field and click the search icon. Select a product. Click Documentation: Doc Center to go to the product page in the Doc Center. Select a release from the Release list and click SEARCH. Click on the PDF icon to open or save the file. END OF STEPS Procedures with options or substeps When there are options in a procedure, they are identified by letters. When there are required substeps in a procedure, they are identified by roman numerals. Example of options in a procedure At Step 1, you can choose option a or b. At Step 2, you must do what the step indicates. This step offers two options. You must choose one of the following:

a. This is one option. b. This is another option. You must perform this step. END OF STEPS Example of required substeps in a procedure At Step 1, you must perform a series of substeps within a step. At Step 2, you must do what the step indicates. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t D r a f t 9 1 2 1 2 3 4 5 6 t f a r D t f a r D 10 About this document 7368 ISAM ONT This step has a series of substeps that you must perform to complete the step. You must perform the following substeps:

a. This is the first substep. b. This is the second substep. c. This is the third substep. You must perform this step. END OF STEPS Multiple PDF document search You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel. The results are grouped by PDF file, and you can expand the entry for each file. Note:The PDF files in which you search must be in the same folder. To search multiple PDF files for a common term Select EditSearch from the Acrobat Reader main menu. The Search PDF panel displays. Open Adobe Acrobat Reader. Enter the search criteria. Select All PDF Documents In. Select the folder in which to search using the list. Acrobat Reader displays the search results. You can expand the entries for each document by clicking on the + symbol. Click Search. END OF STEPS Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 About this document 7368 ISAM ONT Technical support How to comment For details, refer to the Nokia Support portal (https://customer.nokia.com/support/s/). For ordering information, contact your Nokia sales representative. Note to reviewers: The following "How to comment" text will appear in the final document when it is published. However, the feedback method described below is for use only on final documents. Please send your review comments to the author using the process you were given when you received this draft document. To comment on this document, go to the Online Comment Form (https://documentation.nokia.com/

comments/) or e-mail your comments to the Comments Hotline (mailto:comments@nokia.com). September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t D r a f t 11 About this document 7368 ISAM ONT t f a r D t f a r D 12 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 ETSI ONT safety guidelines Safety instructions 7368 ISAM ONT D r a f t 1 ETSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals (ONTs). 1.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 1.1.1 Safety instruction boxes The safety instruction boxes are provided in the ONT customer documentation. Observe the instructions to meet safety requirements. The following is an example of the Danger box. The Danger box indicates that the described activity or situation may pose a threat to personal safety. It calls attention to a situation or procedure which, if not correctly performed or adhered to, may result in death or serious physical harm. Do not proceed beyond a Danger box until the indicated conditions are fully understood and met. The following is an example of the Warning box. DANGER Hazard Possibility of personal injury. WARNING Equipment Damage Possibility of equipment damage. Possibility of data loss. The Warning box indicates that the described activity or situation may, or will, cause equipment damage, loss of data, or serious performance problems. It identifies a possible equipment-

damaging situation or provides essential information to avoid the degradation of system operations or data. Do not proceed beyond a warning until the indicated conditions are fully understood and met. The following is an example of the Caution box. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 13 ETSI ONT safety guidelines Safety instructions t f a r D CAUTION Service Disruption Possibility of service interruption. Service interruption. 7368 ISAM ONT The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box. Note: Information of special interest. The Note box provides information that assists the personnel working with ONTs. It does not provide safety-related instructions. 1.1.2 Safety-related labels The ONT equipment is labeled with the specific safety instructions and compliance information that is related to a variant of the ONT. Observe the instructions on the safety labels. Table 1-1, Safety labels (p. 13) provides sample safety labels on the ONT equipment. Table 1-1 Safety labels Description ESD warning PSE marking Laser classification Class 1 laser product Label text Caution: This assembly contains an electrostatic sensitive device. These power supplies are Japan PSE certified and compliant with Japan VCCI emissions standards. Figure 1-1, PSE certification (p. 14) shows the PSE certification. Figure 1-1 PSE certification This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Warning 19841 t f a r D 14 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 ETSI ONT safety guidelines Safety standards compliance 7368 ISAM ONT D r a f t 1.2 Safety standards compliance This section describes the ONT compliance with the European safety standards. 1.2.1 EMC, EMI, and ESD compliance The ONT equipment complies with the following EMC, EMI, and ESD requirements:

EN 300-328 v1.9.1 wide band data transmission standards for 2.4GHz bands EN 300-386 V1.5.1: Electromagnetic Compatibility and Radio Spectrum Matters (ERM):

Telecommunications Network Equipment; Electromagnetic Compatibility (EMC) requirements;

Electrostatic Discharge (ESD) requirements EN 55022 (2006): Class B, Information Technology Equipment, Radio Disturbance Characteristics, limits and methods of measurement EN 55024 (2010): Information Technology Equipment, Immunity Characteristics, limits and methods of measurement European Council Directive 2004/108/EC EN 300-386 V1.4.1: 2008 EN 55022:2006 Class B (ONTs) 1.2.2 Equipment safety standard compliance The ONT equipment complies with the requirements of EN 60950-1, Safety of Information Technology Equipment for use in a restricted location (per R-269). 1.2.3 Environmental standard compliance The ONT equipment complies with the EN 300 019 European environmental standards. 1.2.4 Laser product standard compliance For most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2 for laser products. If there is an exception to this compliance regulation, you can find this information in the standards compliance section of the unit data sheet in this Product Guide. 1.2.5 Resistibility requirements compliance The ONT equipment complies with the requirements of ITU Recommendation K.21 for resistibility of telecommunication equipment installed in customer premises to over voltage and over currents. 1.2.6 Acoustic noise emission standard compliance The ONT equipment complies with EN 300 753 acoustic noise emission limit and test methods. 1.3 Electrical safety guidelines This section provides the electrical safety guidelines for the ONT equipment. Note: The ONTs comply with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 15 ETSI ONT safety guidelines ESD safety guidelines t f a r D The ONTs comply with BS EN 61140. 1.3.1 Power supplies 7368 ISAM ONT The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. 1.3.2 Cabling The following are the guidelines regarding cables used for the ONT equipment:

All cables must be approved by the relevant national electrical code. The cables for outdoor installation of ONTs must be suitable for outdoor use. POTS wiring run outside the subscriber premises must comply with the requirements of local electrical codes. In some markets, the maximum allowed length of the outside run is 140 feet (43 m). If the outside run is longer, NEC requires primary protection at both the exit and entry points for the wire. Earthing and bonding of the ONTs must comply with the requirements of local electrical codes. The ONT equipment is sensitive to ESD. Operations personnel must observe the following ESD instructions when they handle the ONT equipment. 1.3.3 Protective earth 1.4 ESD safety guidelines CAUTION Service Disruption This equipment is ESD sensitive. Proper ESD protections should be used when you enter the TELCO Access portion of the ONT. During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD. 1.5 Laser safety guidelines Observe the following instructions when you perform installation, operations, and maintenance tasks on the ONT equipment. Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system. t f a r D 16 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t ETSI ONT safety guidelines Laser safety guidelines DANGER Hazard DANGER Hazard There may be invisible laser radiation at the fiber optic cable when the cable is removed from the connector. Avoid direct exposure to the laser beam. Observe the following danger for laser hazard. Eyes can be damaged when they are exposed to a laser beam. Take necessary precautions before you plug in the optical modules. Possibility of equipment damage. Risk of eye damage by laser radiation. 1.5.1 Laser classification Laser warning labels The ONT is classified as a Class 1 laser product based on its transmit optical output. The following figures show the labels related to laser product, classification and warning. Figure 1-2, Laser product label (p. 16) shows a laser product label. Figure 1-2 Laser product label Figure 1-3, Laser classification label (p. 18) shows a laser classification label. Laser classification labels may be provided in other languages. 18455 September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 17 ETSI ONT safety guidelines Laser safety guidelines t f a r D Figure 1-3 Laser classification label 7368 ISAM ONT CLASS 1 LASER PRODUCT

PRODUCTO LASER CLASE 1

CLASE 1 DEL LASER LASER CLASSE 1 18992 Figure 1-4, Laser warning labels (p. 19) shows a laser warning label and an explanatory label for laser products. Labels and warning may be provided in other languages. The explanatory label provides the following information:

a warning that calls attention to the invisible laser radiation an instruction against staring into the beam or viewing directly with optical instruments wavelength normal output power maximum output power t f a r D 18 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 ETSI ONT safety guidelines Laser safety guidelines Figure 1-4 Laser warning labels 7368 ISAM ONT D r a f t INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE

EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER. FAIRE APPEL A UN PERSONNELL QUALIFIE CLASE 1 DEL LASER RADIACION DE LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION AL RAYO LASER. NO DESMONTAR. LLAMAR A PERSONAL AUTORIZADO INVISIBLE LASER RADIATION PRESENT AT FIBER OPTIC CABLE WHEN NOT CONNECTED. AVOID DIRECT EXPOSURE TO BEAM. Laser Warning Label 18993 1.5.2 Transmit optical output The maximum transmit optical output of an ONT is +5 dBm. 1.5.3 Normal laser operation In normal operation, fiber cable laser radiation is always off until it receives signal from the line terminal card. Eyes can be damaged when they exposed to a laser beam. Operating personnel must observe the instructions on the laser explanatory label before plugging in the optical module. DANGER Hazard Risk of eye damage by laser radiation. 1.5.4 Location class Use cable supports and guides to protect the receptacles from strain. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 19 ETSI ONT safety guidelines Environmental requirements t f a r D 1.6 Environmental requirements 7368 ISAM ONT See the ONT technical specification documentation for more information about temperature ranges. During operation in the supported temperature range, condensation inside the ONT caused by humidity is not an issue. To avoid condensation caused by rapid changes in temperature and humidity, Nokia recommends:

The door of the ONT not be opened until temperature inside and outside the enclosure has stabilized. If the door of the ONT must be opened after a rapid change in temperature or humidity, use a dry cloth to wipe down the metal interior to prevent the risk of condensation. When high humidity is present, installation of a cover or tent over the ONT helps prevent condensation when the door is opened. t f a r D 20 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 ETSI environmental and CRoHS guidelines Environmental labels 7368 ISAM ONT D r a f t 2 ETSI environmental and CRoHS guidelines This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line termination (OLT) and optical network termination (ONT) systems. This chapter also includes environmental operation parameters of general interest. 2.1 Environmental labels This section describes the environmental instructions that are provided with the customer documentation, equipment, and location where the equipment resides. 2.1.1 Overview CRoHS is applicable to Electronic Information Products (EIP) manufactured or sold and imported in the territory of the mainland of the Peoples Republic of China. EIP refers to products and their accessories manufactured by using electronic information technology, including electronic communications products and such subcomponents as batteries and cables. 2.1.2 Environmental related labels Environmental labels are located on appropriate equipment. The following are sample labels. Products below Maximum Concentration Value (MCV) label Figure 2-1, Products below MCV value label (p. 22) shows the label that indicates a product is below the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). Products with this label are recyclable. The label may be found in this documentation or on the product. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 21 ETSI environmental and CRoHS guidelines Environmental labels 7368 ISAM ONT t f a r D Figure 2-1 Products below MCV value label 18986 Products containing hazardous substances above Maximum Concentration Value (MCV) label Figure 2-2, Products above MCV value label (p. 22) shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). The number contained inside the label indicates the Environment-Friendly User Period (EFUP) value. The label may be found in this documentation or on the product. Figure 2-2 Products above MCV value label Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories. These values are based on manufacturers' extensive practical experience of the design, manufacturing, maintenance, usage conditions, operating t f a r D 22 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 ETSI environmental and CRoHS guidelines Hazardous Substances Table (HST) 7368 ISAM ONT D r a f t environments, and physical condition of infrastructure and handsets after years of service. The values reflect minimum values and refer to products operated according to the intended use conditions. See 2.2 Hazardous Substances Table (HST) (p. 22) for more information. 2.2 Hazardous Substances Table (HST) This section describes the compliance of the OLT and ONT equipment to the CRoHS standard when the product and sub assemblies contain hazardous substances beyond the MCV value. This information is found in this user documentation where part numbers for the product and sub assemblies are listed. It may be referenced in other OLT and ONT documentation. In accordance with the Peoples Republic of China Electronic Industry Standard Marking for the Control of Pollution Caused by Electronic Information Products (SJ/T11364-2006), customers may access the Nokia Hazardous Substance Table, in Chinese, from the following location:

http://www.alcatel-sbell.com.cn/wwwroot/images/upload/private/1/media/ChinaRoHS.pdf

(http://www.alcatel-sbell.com.cn/wwwroot/images/upload/private/1/media/ChinaRoHS.pdf) 2.3 Other environmental requirements Observe the following environmental requirements when handling the P-OLT or ONT equipment. 2.3.1 ONT environmental requirements See the ONT technical specification documentation for more information about temperature ranges. 2.3.2 Storage 2.3.3 Transportation 2.3.4 Stationary use According to ETS 300-019-1-1 - Class 1.1, storage of ONT equipment must be in Class 1.1, weather-protected, temperature-controlled locations. According to EN 300-019-1-2 - Class 2.3, transportation of the ONT equipment must be in packed, public transportation with no rain on packing allowed. According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of ONT equipment must be in a temperature-controlled location, with no rain allowed, and with no condensation allowed. 2.3.5 Material content compliance European Union (EU) Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment. This Directive applies to electrical and electronic products placed on the EU market after 1 July 2006, with various exemptions, including an exemption for lead solder in network infrastructure equipment. Nokia products shipped to the EU after 1 July 2006 comply with the EU RoHS Directive. Nokia has implemented a material/substance content management process. The process is described in: Nokia process for ensuring RoHS Compliance (1AA002660031ASZZA). This ensures September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 23 t f a r D t f a r D 24 ETSI environmental and CRoHS guidelines Other environmental requirements 7368 ISAM ONT compliance with the European Union Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS2). With the process equipment is assessed in accordance with the Harmonised Standard EN50581:2012 (CENELEC) on Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances. 2.3.6 End-of-life collection and treatment Electronic products bearing or referencing the symbol shown in Figure 2-3, Recycling/take back/

disposal of product symbol (p. 23), when put on the market within the European Union (EU), shall be collected and treated at the end of their useful life, in compliance with applicable EU and local legislation. They shall not be disposed of as part of unsorted municipal waste. Due to materials that may be contained in the product, such as heavy metals or batteries, the environment and human health may be negatively impacted as a result of inappropriate disposal. Note: In the European Union, a solid bar under the symbol for a crossed-out wheeled bin indicates that the product was put on the market after 13 August 2005. Figure 2-3 Recycling/take back/disposal of product symbol At the end of their life, the OLT and ONT products are subject to the applicable local legislations that implement the European Directive 2012/19EU on waste electrical and electronic equipment

(WEEE). There can be different requirements for collection and treatment in different member states of the European Union. In compliance with legal requirements and contractual agreements, where applicable, Nokia will offer to provide for the collection and treatment of Nokia products bearing the logo shown in Figure 2-3, Recycling/take back/disposal of product symbol (p. 24) at the end of their useful life, or products displaced by Nokia equipment offers. For information regarding take-back of equipment by Nokia, or for more information regarding the requirements for recycling/disposal of product, contact your Nokia account manager or Nokia take back support at sustainability.global@nokia.com. Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 ANSI ONT safety guidelines Safety instructions 7368 ISAM ONT D r a f t 3 ANSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals or units (ONTs or ONUs) in the North American or ANSI market. 3.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 3.1.1 Safety instruction boxes in customer documentation The safety instruction boxes are provided in the ONT customer documentation. Observe the instructions to meet safety requirements. The following is an example of the Danger box. The Danger box indicates that the described activity or situation may pose a threat to personal safety. It calls attention to a situation or procedure which, if not correctly performed or adhered to, may result in death or serious physical harm. Do not proceed beyond a Danger box until the indicated conditions are fully understood and met. The following is an example of the Warning box. DANGER Hazard Possibility of personal injury. WARNING Equipment Damage Possibility of equipment damage. Possibility of data loss. The Warning box indicates that the described activity or situation may, or will, cause equipment damage, loss of data, or serious performance problems. It identifies a possible equipment-

damaging situation or provides essential information to avoid the degradation of system operations or data. Do not proceed beyond a warning until the indicated conditions are fully understood and met. The following is an example of the Caution box. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 25 ANSI ONT safety guidelines Safety instructions t f a r D CAUTION Service Disruption Possibility of service interruption. Service interruption. 7368 ISAM ONT The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box. Note: Information of special interest. The Note box provides information that assists the personnel working with ONTs. It does not provide safety-related instructions. 3.1.2 Safety-related labels The ONT equipment is labeled with specific safety compliance information and instructions that are related to a variant of the ONT. Observe the instructions on the safety labels. Table 3-1, Safety labels (p. 25) provides examples of the text in the various ONT safety labels. Table 3-1 Safety labels Description UL compliance TUV compliance ESD warning Label text Communication service equipment US listed. Type 3R enclosure - Rainproof. Type 3R enclosure - Rainproof. Caution: This assembly contains electrostatic sensitive device. Laser classification Class 1 laser product Laser product compliance This laser product conforms to all applicable standards of 21 CFR 1040.10 at date of manufacture. FCC standards compliance Tested to comply with FCC standards for home or office use. CDRH compliance Operation conditions Canadian standard compliance

(modular ONT) Canadian standard compliance

(outdoor ONT) Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class A digital apparatus complies with Canadian ICES-003. This Class B digital apparatus complies with Canadian ICES-003. CE marking There are various CE symbols for CE compliance. t f a r D 26 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 ANSI ONT safety guidelines Safety standards compliance Figure 3-1, Sample safety label on the ONT equipment (p. 26) shows a sample safety label on the ONT equipment. Figure 3-1 Sample safety label on the ONT equipment 7368 ISAM ONT D r a f t Tested to Comply with FCC Standards FOR HOME OR OFFICE USE c COMMUNICATION SERVICE EQUIPMENT US LISTED 27FY Type 3R Enclosure - Rainproof This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la class A est conforme a la norme NMB-003 du Canada CAUTION This Assembly Contains Electrostatic Sensitive Devices 18533 3.2 Safety standards compliance This section describes the ONT compliance with North American safety standards. WARNING Equipment Damage Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 3.2.1 EMC, EMI, and ESD standards compliance The ONT equipment complies with the following requirements:

Federal Communications Commission (FCC) CFR 47, Part 15, Subpart B, Class A requirements for OLT equipment GR-1089-CORE requirements, including:

Section 3 Electromagnetic Interference, Emissions Radiated and Conducted Section 3 Immunity, Radiated and Conducted Section 2 ESD Discharge Immunity: System Level Electrostatic Discharge and EFT Immunity:

Electrically Fast Transients September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 27 ANSI ONT safety guidelines Safety standards compliance t f a r D 7368 ISAM ONT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is needed. Consult the dealer or an experienced radio/TV technician for help. 3.2.2 Equipment safety standard compliance The ONT equipment complies with the requirements of UL60950-1, Outdoor ONTs to Communication Service Equipment (CSE) and Indoor ONTs to Information Technology Equipment

(ITE). 3.2.3 Environmental standards compliance The ONT equipment complies with the following standards:

GR-63-CORE (NEBS): requirements related to operating, storage, humidity, altitude, earthquake, office vibration, transportation and handling, fire resistance and spread, airborne contaminants, illumination, and acoustic noise GR-487-CORE: requirements related to rain, chemical, sand, and dust GR-487 R3-82: requirements related to condensation GR-3108: Requirements for Network Equipment in the Outside Plant (OSP) TP76200: Common Systems Equipment Interconnections Standards 3.2.4 Laser product standards compliance The ONT equipment complies with 21 CFR 1040.10 and CFR 1040.11, except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 or to 21 CFR 1040.10 U.S. Center for Devices and Radiological Health (CDRH) of the Food and Drug Administration (FDA) Laser Notice 42 for ONTs containing Class 1 Laser modules certified by original manufactures. Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such as Nokia ONTs shall leave the following Laser Safety cautions with the end user. a) Class 1 Laser Product b) Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Figure 3-2, Sample laser product label showing CDRH 21 CFR compliance (p. 29) shows a laser product label. t f a r D 28 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 ANSI ONT safety guidelines Laser safety guidelines Figure 3-2 Sample laser product label showing CDRH 21 CFR compliance 7368 ISAM ONT D r a f t 3FE55851ABAA MAC:XXXXXXXXXXXX SN:ALCLXXXXXXXX Model:

MFG:

MONTH: XX YEAR: XXXX ICS: XX MRev: XX I.T.E Intertek 4006119 FCC ID: XXXXXXXXXXX CLASS 1 LASER PRODUCT PRODUIT LASER DE CLASSE 1 3A 12VDC ASSEMBLED IN CHINA 2301 Sugar Bush Rd. Raleigh, NC 27612 This device complies with Part 15 of the FCC Rule. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including intereference that may cause undesired operation. DANGER - Invisible Laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM. DANGER - Rayonnement Laser invisible lorsquelle est ouverte. Evitee lexpostion direct au faisceau. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50 dated June 24, 2007 18532 3.2.5 Resistibility requirements compliance The ONT equipment complies with the requirements of ITU Recommendation K.21 for resistibility of telecommunication equipment installed in customer premises to over voltage and over currents. 3.3 Laser safety guidelines Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system. Observe the following warnings when you perform installation, operations, and maintenance tasks on the ONT equipment. There may be invisible laser radiation at the fiber optic cable when the cable is removed from the connector. Avoid direct exposure to beam. Observe the following danger for a laser hazard. Eyes can be damaged when they are exposed to a laser beam. Take necessary precautions before you plug in the optical modules. DANGER Hazard DANGER Hazard Possibility of equipment damage. Risk of eye damage by laser radiation. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 29 ANSI ONT safety guidelines Laser safety guidelines t f a r D 7368 ISAM ONT Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such as Nokia ONTs shall leave the following Laser Safety cautions with the end user. a) Class 1 Laser Product b) Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. 3.3.1 Laser warning labels The following figures show sample labels related to laser product, classification and warning. Figure 3-3, Laser product label (p. 29) shows a laser product label. Figure 3-3 Laser product label Figure 3-4, Laser classification label (p. 30) shows a laser classification label. Laser classification labels may be provided in other languages. Figure 3-4 Laser classification label CLASS 1 LASER PRODUCT

PRODUCTO LASER CLASE 1

CLASE 1 DEL LASER LASER CLASSE 1 18455 18992 Figure 3-5, Laser warning labels (p. 31) shows a laser warning label and an explanatory label for laser products. Explanatory labels may be provided in other languages. The explanatory label provides the following information:

a warning that calls attention to the invisible laser radiation an instruction against staring into the beam or viewing directly with optical instruments t f a r D 30 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 ANSI ONT safety guidelines Laser safety guidelines wavelength normal output power maximum output power Figure 3-5 Laser warning labels 7368 ISAM ONT D r a f t INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE

EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER. FAIRE APPEL A UN PERSONNELL QUALIFIE CLASE 1 DEL LASER RADIACION DE LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION AL RAYO LASER. NO DESMONTAR. LLAMAR A PERSONAL AUTORIZADO INVISIBLE LASER RADIATION PRESENT AT FIBER OPTIC CABLE WHEN NOT CONNECTED. AVOID DIRECT EXPOSURE TO BEAM. Laser Warning Label 18993 3.3.2 Laser classification The ONT is classified as a Class 1 laser product based on its transmit optical output. For Class 1 laser products, lasers are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing. Figure 3-6, Sample laser product safety label on the ONT equipment (p. 32) shows a sample laser product safety label on the ONT equipment. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 31 ANSI ONT safety guidelines Electrical safety guidelines t f a r D Figure 3-6 Sample laser product safety label on the ONT equipment 7368 ISAM ONT 3FE55851ABAA MAC:XXXXXXXXXXXX SN:ALCLXXXXXXXX Model:

MFG:

MONTH: XX YEAR: XXXX ICS: XX MRev: XX I.T.E Intertek 4006119 FCC ID: XXXXXXXXXXX CLASS 1 LASER PRODUCT PRODUIT LASER DE CLASSE 1 3A 12VDC ASSEMBLED IN CHINA 2301 Sugar Bush Rd. Raleigh, NC 27612 This device complies with Part 15 of the FCC Rule. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including intereference that may cause undesired operation. DANGER - Invisible Laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM. DANGER - Rayonnement Laser invisible lorsquelle est ouverte. Evitee lexpostion direct au faisceau. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50 dated June 24, 2007 18532 3.3.3 Transmit optical output The maximum transmit optical output of an ONT is +5 dBm. 3.3.4 Normal laser operation In normal operation, fiber cable laser radiation is always off until it receives signal from the line terminal card. Operating personnel must observe the instructions on the laser explanatory label before plugging in the optical module. DANGER Hazard Risk of eye damage by laser radiation. 3.3.5 Location class Use cable supports and guides to protect the receptacles from strain. 3.4 Electrical safety guidelines This section provides the electrical safety guidelines for the ONT equipment. Note: The ONTs comply with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards. t f a r D 32 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t ANSI ONT safety guidelines ESD safety guidelines 3.4.1 Power supplies 3.4.2 Cabling The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. The following are the guidelines regarding cables used for the ONT equipment:

Use only cables approved by the relevant national electrical code. Use cables suitable for outdoor use for outdoor installation of ONTs. The ONTs have been evaluated for use with external POTS wiring without primary protection that may not exceed 140 ft (43 m) in reach. However, the power cable must not exceed 100 ft

(31 m). 3.4.3 Protective earth Earthing and bonding of the ONTs must comply with the requirements of NEC article 250 or local electrical codes. 3.5 ESD safety guidelines The ONT equipment is sensitive to ESD. Operations personnel must observe the following ESD instructions when they handle the ONT equipment. CAUTION Service Disruption This equipment is ESD sensitive. Proper ESD protections should be used when entering the TELCO Access portion of the ONT. During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD. Nokia recommends that you prepare the site before you install the ONT equipment. In addition, you must control relative humidity, use static dissipating material for furniture or flooring, and restrict the use of air conditioning. 3.6 Environmental requirements See the ONT technical specification documentation for temperature ranges for ONTs. During operation in the supported temperature range, condensation inside the ONT caused by humidity is not an issue. To avoid condensation caused by rapid changes in temperature and humidity, Nokia recommends:

The door of the ONT not be opened until temperature inside and outside the enclosure has stabilized. If the door of the ONT must be opened after a rapid change in temperature or humidity, use a dry cloth to wipe down the metal interior to prevent the risk of condensation. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 33 ANSI ONT safety guidelines Environmental requirements t f a r D When high humidity is present, installation of a cover or tent over the ONT helps prevent condensation when the door is opened. 7368 ISAM ONT t f a r D 34 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 4 G-2426G-A unit data sheet G-2426G-A unit data sheet Overview 4.1 Overview 4.1.1 Purpose 4.1.2 Contents 7368 ISAM ONT D r a f t 4.1 Overview 4.2 G-2426G-A part numbers and identification 4.3 G-2426G-A general description 4.4 G-2426G-A software and installation feature support 4.5 G-2426G-A interfaces and interface capacity 4.6 G-2426G-A LEDs 4.7 G-2426G-A detailed specifications 4.8 G-2426G-A GEM ports and T-CONTs 4.9 G-2426G-A performance monitoring statistics 4.10 G-2426G-A functional blocks 4.11 G-2426G-A standards compliance 4.12 G-2426G-A special considerations 35 35 37 43 43 45 47 48 48 50 51 53 4.2 G-2426G-A part numbers and identification Table 4-1, Identification of G-2426G-A indoor ONTs (p. 35) provides part numbers and identification information for the G-2426G-A indoor ONT. Table 4-1 Identification of G-2426G-A indoor ONTs Ordering kit part number Provisioning number Description 3FE 49220 AA 3FE 49241 AA CLEI Code CPR ECI/

Bar code 3FE 49220 BA 3FE 49241 BA G-2426G-A,,US Plug,GPON ONT,. Supports 2 POTS port,4 x GE UNI, WIFI 6 2+2 Includes one USB 3.0, 12 V wall-mounted power adapter with US input plug and a 256 MB Flash G-2426G-A ,EU Plug,GPON ONT. Supports 2 POTS port,4 x GE UNI, WIFI 6 2+2 Includes one USB 3.0, 12 V wall-mounted power adapter with 2-pin EU input plug and a 256 MB Flash September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 35 G-2426G-A unit data sheet G-2426G-A part numbers and identification 7368 ISAM ONT Table 4-1 Identification of G-2426G-A indoor ONTs (continued) Ordering kit part number Provisioning number Description CLEI Code CPR ECI/

Bar code 3FE 49220 BB Customer specific variant 3FE 49241 BB G-2426G-A, EU Plug,GPON ONT. Supports 2 POTS port,4xGE UNI, WIFI 6 2+2 Includes one USB 3.0, 12 V wall-mounted power adapter with 2-pin EU input plug and a 512 MB Flash G-2426G-A, UK Plug,GPON ONT. Supports 2 POTS port, 4 x GE UNI, WIFI 6 2+2 Includes one USB 3.0, 12 V wall-mounted power adapter with 3-pin UK input plug and a 256 MB Flash 3FE 49220 CA 3FE 49241 BA Table 4-2, G-2426G-A, dimension data specifications (p. 36) lists the dimension data specifications for G-2426G-A, indoor ONT Table 4-2 G-2426G-A, dimension data specifications number of supported Wi-Fi clients (per radio, per device, per mesh) 64 per radio, 128 per device, no mesh support. Dimension Packet size supported number of IP addresses supported (or ranges) number of supported beacons /APs in a mesh number of supported WAN interfaces number of supported VLANs number of LLIDs in the ONTs Specification 2000 254 8 4094 number of Tconts and GEM ports in the ONTs 32 Tconts / 256 GEM ports number of priority queues, overall buffer size 128, Max 16MB for WAN and 4MB for LAN number of multicast groups (DACL entries) 1024 Table 4-3, G-2426G-A power supply ordering information (p. 37) provides the power supply information for the G-2426G-A ONT. For more information on power supplies, see the 7368 ISAM ONT Power Supply and UPS Guide. The power consumption is less than 24 W. t f a r D t f a r D 36 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 G-2426G-A unit data sheet G-2426G-A general description Table 4-3 G-2426G-A power supply ordering information ONT part numbers Power model

(Model No./Manufacture Part Number) Power information 7368 ISAM ONT D r a f t Kit: 33FE 49220 AA EMA: 3FE 49241 AA KIT: 3FE 49220 BA EMA: 3FE 49241 BA KIT: 3FE 49220 BB EMA: 3FE 49241 BB KIT: 3FE 49220 CA EMA: 3FE 49241 BA FUHUA: UES24WU120200SPA/

UE200529GWZF2RI RUIDE:RD1202000-C55-154MG/

BR120200-UC6C-LL03 FUHUA:UES24WV120200SPA/

UE200529GWZF1RI RUIDE: RD1202000-C55-154OG/

BR120200-EC6C-LL03 FUHUA:UES24WV120200SPA/

UE200529GWZF1RI RUIDE: RD1202000-C55-154OG/

BR120200-EC6C-LL03 FUHUA:UES24WB120200SPA/

UE200529GWZF3RI RUIDE:RD1202000-C55-154YG/

BR120200-YC6C-LL03 Customer category or country compliance tested for Notes ANSI municipality US, UL/CB certified, 2-pin US input plug Europe, CE certified 2-pin EUinput plug Europe, CE certified UK, CE certified 2-pin EU input plug Dummy 3-pin UK nput plug 12 V wall mounted AC/DC power adapter, US plug in 12 V wall mounted AC/DC power adapter, EU plug in 12 V wall mounted AC/DC power adapter, EU plug in 12 V wall mounted AC/DC power adapter, UK plug in 4.3 G-2426G-A general description G-2426G-A indoor ONTs provide the subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The G-2426G-A has built-in Wi-Fi 802.11 b/g/n/ac networking with triple play capability and can provide triple play services with voice, video and data. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes

(Type I, Type II, and Type III). The ONT can be placed on a flat surface, such as a desk or shelf. Purpose (p. 0) shows the G-2426G-A ONT September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 37 t f a r D t f a r D 38 G-2426G-A unit data sheet G-2426G-A general description 7368 ISAM ONT USB TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 POWER WLAN RESET ON/OFF WPS LED USB port POTS port

(RJ-11) Ethernet ports (4)

(RJ-45) Reset button Power Wi-Fi security/

on/off buttons On/off button 36176 Figure 4-1 G-2426G-A (internal antenna) POWER LINK AUTH LAN1 LAN2 LAN3 LAN4 WPS WLAN2.4G WLAN5G TEL1 TEL2 VOIP INTERNET USB G-2426G-A indoor ONTs provide the following functions:

35957 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 G-2426G-A unit data sheet G-2426G-A general description 7368 ISAM ONT D r a f t Dual-band concurrent 2x2 IEEE 802.11b/g/n 2.4 GHz and 802.11ac MIMO 5 GHz Supports 802.11 b/g/n 2x2 Wireless 2.4 GHz MIMO; Channel bandwidth 20, 40 MHz, auto Supports 802.11ac 2x2 Wireless 5 GHz Mu-MIMO; Channel bandwidth 20, 40, 80 MHz, auto Four Gigabit standard RJ-45 10/100/1000 Mbps, auto negotiating Ethernet ports and MDI/MDIX auto sensing Two POTS ports with R-J11 connectors Two USB 2.0 Type A ports Note:

The POTS ports and supported USB ports varies for each specific variant. For details, see Table 4-1, Identification of G-2426G-A indoor ONTs (p. 35) for the configuration on each specific variant. GPON uplink: G.984 and G.988 series standard compliant 256MB NAND Flash with bad block management, 512MB DDR3 RAM, pin2pin compatible design for possible upgrade of RAM/Flash WLAN on/off push button WPS on/off push button LEDs on/off push button Reset button Triple-Play services, including voice, video and high speed Internet access Support for fax services Built-in layer 2 switch; Line Rate L2 traffic IP video distribution Wavelength: 1490 nm downstream; 1310 nm upstream Supports WBF filter.The GPON ONTs can co-exist with XGSPON ONTs in the same PON PHY rate: 300 Mbps for 2.4 G and 867 Mbps for 5 G External antennas with 5dBi gain for each Optics that support received signal strength indication (RSSI) 64/128 WEP encryption WPA, WPA-PSK/TKIP WPA2, WPA2-PSK/AES Dying gasp support Multiple voice Code DTMF dialing VLAN tagging/detagging and marking/remarking of IEEE 802.1p per Ethernet port. Voice Services via Session Initiation Protocol (SIP) Echo cancellation (G.168) Fax mode configuration (T.30/T.38) Caller ID, call waiting, call hold, 3-way calling, call transfer, message waiting September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 39 G-2426G-A unit data sheet G-2426G-A general description 7368 ISAM ONT Forward Error Correction (FEC) further details. support for multiple SSIDs (private and public instances); contact your Nokia representative for Conductive power: 250mW/24 dBm (2.4 GHz); 500 mW/27 dBm (5GHz) Maximum effective isotropic radiated power (EIRP):

5dBi external antenna: 800mW/29dBm (2.4GHz);1600mW/32dBm (5GHz) 3dBi internal antenna: 500mW/27dBm (2.4GHz);1000mW/30dBm (5GHz) t f a r D t f a r D 40 Bridged mode or routed mode per LAN port TR-069 support Ethernet-based Point-to-Point (PPPoE) DHCP client/server DNS server/client DDNS Port forwarding Network Address Translation (NAT) Network Address Port Translation (NAPT) UPnP IGD2.0 support ALG IGMP snooping and proxy (v2/v3) Traffic classification and QoS capability OMCI/TR-069 Web GUI configuration Performance monitoring and alarm reporting Remote software image downloading and activation IP/MAC/URL filter Multi-level firewall and ACL Econet ONT in mainstream 4.3.1 TR-069 parameter support The G-2426G-A ONT supports the following TR-069 features:

Host object Port forwarding Optical parameters Object support for optical parameters Statistics and troubleshooting Diagnostic parameter Component parameter (TR157) Host object support Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 G-2426G-A unit data sheet G-2426G-A general description The ONT provides host object support for: InternetGatewayDeviceLANDevice.Hosts.Host. The ONT supports the port forwarding of objects via TR-069:

7368 ISAM ONT D r a f t Port forwarding support Application Name WAN Port LAN Port Internal Client Protocol Enable Mapping WAN Connection List laser bias current voltage temperature received signal levels lower thresholds These are the same port forwarding parameters supported in the GUI. For more information, see Table 7-32, Port Forwarding parameters (p. 137) in Chapter 7, Configure a G-2426G-A indoor ONT. Optical parameters support The ONT supports the reading of optical parameters via TR-069:

These are the same optical parameters supported in the GUI. For more information, see Table 7-6, Optics Module Status parameters (p. 83) in Chapter 7, Configure a G-2426G-A indoor ONT. Object support for WiFi parameters The ONT supports the status retrieval and configuration of the following Wi-Fi parameters via TR-

069:

channel SSID WPS password for WPA and WEP Tx power (transmission rate in percentage of maximum transmit power) These are the same TR-069 object parameters that are supported in the GUI. For more information, see Table 7-13, Wireless (2.4GHz) parameters (p. 99) and Table 7-14, Wireless (5GHz) parameters (p. 102) in Chapter 7, Configure a G-2426G-A indoor ONT. Statistics and troubleshooting support The ONT supports TR-069 statistics and troubleshooting for LAN, WAN, and WiFi. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 41 t f a r D t f a r D 42 G-2426G-A unit data sheet G-2426G-A general description 7368 ISAM ONT Diagnostic parameter support The ONT supports the following TR-069 diagnostic parameters:

TR-143 IP ping traceroute These are the same diagnostic parameters supported in the GUI. For more information, see 7.56 Diagnosing WAN connections (p. 163) in Chapter 7, Configure a G-2426G-A indoor ONT. 4.3.2 TR69 authentication using TLS and CA certificates G-2426G-A ONTs support TLS, as well as ACS authentication using SHA-256 pre-installed certificates. If the URL is set to the https://... format, by default, the connection will use TLS without authentication mode. The ONT can also authenticate the ACS using a pre-installed CA certificate. The G-2426G-A ONTs support TLSv1.3 for TR069. The ONT supports download certification from ACS. 4.3.3 TR-104 parameter extension support for voice service A vendor specific attribute has been added to the TR-104 Voice Service object structure to enable the ACS to configure the name of the embedded GSIP XML file to be selected. The TR-104 Voice Service Object is:

InternetGatewayDevice.Services.VoiceService.{i}.Capabilities.SIP. The vendor specific attribute is: X_ALU-COM_XML_File_Name_Path. 4.3.4 TR-104 voice-related alarms The G-2426G-A ONT supports the following four TR-104 voice-related alarms on a per FXS port basis. These alarms all represent SIP registration failures with an alarm level of MAJOR. SIPREGDNS: domain name could not be resolved SIPREGAUTH: authentication failed SIPREGTO: re-transmissions timed out SIPREGERR: error response from the registration server 4.3.5 TR-104 parameters for FX line testing New attributes have been added to the TR-104 Voice Service object structure to enable the ACS to perform line tests. The ONT supports the following electrical line tests:

hazardous potential foreign electrical motive force resistive faults receiver off-hook test Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 G-2426G-A unit data sheet G-2426G-A software and installation feature support 7368 ISAM ONT ringers test 4.3.6 TR-111 support The G-2426G-A ONT supports TR-111, which extends the WAN Management Protocol defined in TR-069 to enhance the ability to remotely manage LAN devices. The device-gateway association enables an ACS to identify the associated gateway through which a device is connected. A connect request via the NAT gateway enables an ACS to initiate a TR-069 session with a device that is operating behind a NAT gateway. 4.3.7 TR-157 support The ONT can support LXC container for third party software component. These software components are managed by ACS with the parameters defined in TR-157. The TR-157 objects are:

Mange each software component via SoftwareModules.DeploymentUnit.{i}

Set software component execution environment via SoftwareModules.ExecEnv.{i}

Run software component and get the execution status via SoftwareModules.ExecutionUnit.{i}

4.4 G-2426G-A software and installation feature support For information on installing or replacing the G-2426G-A see:

Chapter 5, Install a G-2426G-A indoor ONT Chapter 6, Replace a G-2426G-A indoor ONT For information on the following topics, see the 7368 ISAM ONT Product Overview Guide:

ONT and MDU general descriptions of features and functions Ethernet interface specifications POTS interface specifications RSSI specifications Wi-Fi specifications ONT optical budget SLID entry via Ethernet port ONT management using an ONT interface 4.5 G-2426G-A interfaces and interface capacity Table 4-4, G-2426G-A indoor ONT interface connection capacity (p. 44) describes the supported interfaces and interface capacity for G-2426G-A indoor ONTs. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t D r a f t 43 t f a r D Notes:

G-2426G-A unit data sheet G-2426G-A interfaces and interface capacity 7368 ISAM ONT Table 4-4 G-2426G-A indoor ONT interface connection capacity ONT type and model Maximum capacity POTS 10/ 100 BASE-T 10/ 100/ 1000 BASE-T RF video

(CATV) MoCA VDSL2 E1/T1 Local craft GPON SC/APC G-2426G-A 1 2 4 1 1. The G-2426G-A ONTs provide Wi-Fi service that is enabled and disabled using a Wi-Fi on/off switch. 4.5.1 G-2426G-A connections and components G-2426G-A connections and components (p. 0) shows the physical connections for G-2426G-A indoor ONTs. There are two types of G-2426G-A ONTs, one supports two USB ports and another one without USB. USB TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 POWER WLAN RESET ON/OFF WPS LED USB port POTS port

(RJ-11) Ethernet ports (4)

(RJ-45) Reset button Power Wi-Fi security/

on/off buttons On/off button 36176 Table 4-5, G-2426G-A indoor ONT physical connections (p. 45) describes the physical connections for G-2426G-A indoor ONTs. t f a r D 44 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 G-2426G-A unit data sheet G-2426G-A LEDs Table 4-5 G-2426G-A indoor ONT physical connections Connection 1 Print Letters Description 7368 ISAM ONT D r a f t POTS port TEL1 and TEL2 This connection is provided through an RJ-11 port. One POTS connection is supported.The POTS port supports voice services. Ethernet ports LAN1 to LAN4 This connection is provided through Ethernet RJ-45 connectors. Up to four 10/100/1000 Base-T Ethernet interfaces are supported.The Ethernet ports can support both data and in-band video services on all four interfaces. Power input POWER This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection. Reset button RESET Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID. Accessible through a 2mm pin hole. WLAN button WLAN Wi-Fi service is compliant with IEEE 802.11 standards and is enabled and disabled using the WLAN button. WPS button WPS The Wi-Fi Protected Setup (WPS) button enables and disables the WPS for 2.4GHz and 5GHz. LED button LED The LED button turns the LED indicators on or off. On/Off button ON/OFF This button turns the ONT on or off. USB port USB Fiber optic port

This connection is provided through 1 USB port on the side of the ONT. The ONT supports external USB hard drives that can be made accessible to all LAN devices. The SC/APC fiber optic port is located at the back of the ONT and provides the connection for the fiber optic cable. 1. The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power Notes:

connector. 4.6 G-2426G-A LEDs Figure 4-2, G-2426G-A indoor ONT LEDs (p. 46) shows the G-2426G-A indoor ONT LEDs. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 45 G-2426G-A unit data sheet G-2426G-A LEDs t f a r D Figure 4-2 G-2426G-A indoor ONT LEDs 7368 ISAM ONT POWER LINK AUTH LAN1 LAN2 LAN3 LAN4 WPS WLAN2.4G WLAN5G TEL1 TEL2 VOIP INTERNET USB POWER LINK AUTH LAN1 LAN2 LAN3 LAN4 WPS WLAN2.4G WLAN5G TEL1 TEL2 VOIP INTERNET USB 36235 Table 4-6, G-2426G-A indoor ONT LED descriptions (p. 46) provides LED descriptions for G-2426G-A indoor ONTs. Table 4-6 G-2426G-A indoor ONT LED descriptions LED behavior description Power on Indicator Power Link Auth LAN 1 to 4 LED color and behavior Green solid Red solid Off Green solid Off Off Green solid Green flashing Green solid Green flashing Off Light failed on startup (for example corrupt flash), or self test failed on startup, or self test failed during regular operation or when executed over OMCI Power off GPON link between ONT and OLT is operating normally GPON link is down or no link is connected Fiber is not connected or no power is received to the ONT ONT is configured on the OLT and is in service (UP) ONT is in the process of ranging or synchronizing over the OLT ONT is connected to the associated LAN port (includes devices with wake-on-LAN capability where a slight voltage is supplied to an Ethernet connection) LAN activity is present ONT power is off or Ethernet is not connected t f a r D 46 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t G-2426G-A unit data sheet G-2426G-A detailed specifications Table 4-6 G-2426G-A indoor ONT LED descriptions (continued) Indicator LED color and behavior TEL 1 to 2 Green solid LED behavior description Phone is off hook. Phone is in call in or talking condition All phones are on hook VoIP service is built up and can provide service VoIP service is not built up or out of service VOIP WPS Green flashing Off Green solid Off Green solid Green flashing Red solid Off Green solid Green flashing Green solid Green flashing Off Off Off Off WiFi protected setup link is up (negotiation and auto-configuration successful) WiFi protected setup link activity (negotiation and auto-configuration ongoing) WiFi protected setup processing exception or multiple peers using WPS simultaneously WiFi protected setup link down or no link connected (negotiation has not started or has failed) WLAN 2.4 GHz Green solid WLAN link is enabled in 2.4 GHz Green flashing Traffic is passing through the WLAN link WLAN link is disabled or no link is connected WLAN 5 GHz WLAN link is enabled in 5 GHz Traffic is passing through the WLAN link WLAN link is disabled or no link is connected USB At least one device is connected to the USB port INTERNET Green solid Green flashing There is traffic activity on at least one device connected to the USB port No device is connected to the USB port HSI WAN is connected: a) the device has an IP address assigned from IPCP, DHCP, or static, and no traffic has been detected; b) the session is dropped due to idle timeout but the PON link is still present, or transmit and receive traffic is ongoing. PPPoE or DHCP connection is in progress. HSI WAN is not connected: a) there is no physical interface connection; b) the device is in bridged mode without an assigned IP address; c) the session has been dropped for reasons other than idle timeout. 4.7 G-2426G-A detailed specifications Table 4-7, G-2426G-A indoor ONT physical specifications (p. 47) lists the physical specifications for G-2426G-A indoor ONTs. Table 4-7 G-2426G-A indoor ONT physical specifications Description Length (with internal antenna) Width (with internal antenna)(

Height (with internal antenna) Specification 245 mm 195 mm 80 mm Weight [within 0.5 lb (0.23 kg)] (net weight of ONT) (with internal antenna) 1.05 lbs (480 g) September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 47 G-2426G-A unit data sheet G-2426G-A GEM ports and T-CONTs 7368 ISAM ONT Table 4-8, G-2426G-A indoor ONT power consumption specifications (p. 47) lists the power consumption specifications for G-2426G-A indoor ONT. Table 4-8 G-2426G-A indoor ONT power consumption specifications Mnemonic Condition Minimum power Condition Maximum power

(Not to exceed) G-2426G-A 1 24 W 1 POTS off-hook, 4 10/100/1000 Base-T Ethernet, Wi-Fi operational, USB operational 3.6 W 1 POTS on-hook, other interfaces/services not provisioned Notes:

USB is 18W. 1. The units without USB have lower power consumption. The minimum power consumption for ONT without Table 4-9, G-2426G-A indoor ONT environmental specifications (p. 48) lists the environmental specifications for G-2426G-A indoor ONT. Table 4-9 G-2426G-A indoor ONT environmental specifications Mounting method Temperature range and humidity Altitude On desk or shelf Operating: 23F to 113F ( 5C to 45C) ambient temperature 5% to 95% relative humidity, non-condensing Storage: 4F to 158F ( 20C to 70C) 4.8 G-2426G-A GEM ports and T-CONTs Contact your Nokia technical support representative for more information Table 4-10, G-2426G-A indoor ONT capacity for GEM ports and T-CONTs (p. 48) lists the maximum number of supported T-CONTs and GEM ports. See the appropriate release Customer Release Notes for the most accurate list of supported devices. Table 4-10 G-2426G-A indoor ONT capacity for GEM ports and T-CONTs ONT or MDU Package P ONTs Maximum Notes GEM ports per indoor or outdoor ONT T-CONTs per indoor or outdoor ONT 256 32 256 are present; 254 are available, and 2 are reserved for multicast and debugging 32 are present; 31 are available, and 1 is reserved for OMCI 4.9 G-2426G-A performance monitoring statistics The following section identifies the supported performance monitoring statistics for G-2426G-A ONTs. A check mark indicates the statistic is supported on that ONT. An empty cell indicates the statistic is not supported. The following tables are categorized by supported alarm types:

t f a r D t f a r D 48 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 G-2426G-A unit data sheet G-2426G-A performance monitoring statistics 7368 ISAM ONT Table 4-11, Package S ONTs ONTENET performance monitoring statistics (p. 48) provides statistics for ONTENET type counters Table 4-12, Package S ONTs ONTL2UNI performance monitoring statistics (p. 49) provides statistics for ONTL2UNI type counters Table 4-13, Package S ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance monitoring statistics

(p. 50) provides statistics for PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, and PONONTTCVOIP type counters Table 4-14, Package S ONTs PONONTTC aggregate performance monitoring statistics (p. 50) provides statistics for PONONTTC aggregate type counters Note: If you have trouble accessing G-2426G-A ONTs performance monitoring statistics using TL1, please contact your Nokia support representative for more information about how to access and retrieve performance monitoring type counters. Table 4-11 Package S ONTs ONTENET performance monitoring statistics ONT ONTENET statistics E S C F C E C L O B R F C S F C M T D E T M I E S C E A E R M I L T F 2 O B T E Q S 1. A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window 2. Only packets larger than 9 kB will be counted. Table 4-12 Package S ONTs ONTL2UNI performance monitoring statistics ONT ONTL2UNI statistics S E M A R F S E T Y B S E M A R F C M S M R F D P R D S D S M R F D P R D S U S E M A R F S U S E M A R F S D S E T Y B S U S E T Y B S D S E M A R F C M S U S E M A R F C M S D G-2426G-A 1 Notes:

is 5 seconds G-2426G-A 1 Notes:

is 5 seconds 1. A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t D r a f t 49 G-2426G-A unit data sheet G-2426G-A functional blocks t f a r D 7368 ISAM ONT Table 4-13 Package S ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance monitoring statistics ONT PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP statistics 1. A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window Table 4-14 Package S ONTs PONONTTC aggregate performance monitoring statistics ONT PONONTTC (aggregate) statistics S K C O L B X T S K C O L B X T S G A R F X T S G A R F X T S K C O L B X R S K C O L B X R S G A R F X R S G A R F X R S G A R F T S O L S G A R F T S O L S R D H M E G D A B S R D H M E G D A B G-2426G-A 1 Notes:

is 5 seconds G-2426G-A 1 Notes:

is 5 seconds 1. A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window 4.10 G-2426G-A functional blocks G-2426G-A indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi) service. Wi-Fi service on these ONTs is compliant with the IEEE 802.11 standard and enabled or disabled using a WLAN button. In addition to the Wi-Fi service, these ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two RJ-11 POTS port. These ONTs also feature fiber optic, USB, and power connectors. Figure 4-3, G-2426G-A ONT functional block (p. 51) shows the functional blocks for G-2426G-A indoor ONT. t f a r D 50 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 G-2426G-A unit data sheet G-2426G-A standards compliance Figure 4-3 G-2426G-A ONT functional block 7368 ISAM ONT D r a f t Flash:

256 MB SoC GPON BoSA UART JTAG Buttons LEDs MT7905D MT7975 2x2 11ax 2.4GHz Wifi power: 500mW conductive 2x2 11ax 5GHz Wifi power: 500W conductive FEM FEM transformer USB 2.0 4x1G

(RJ45) 36173 4.11 G-2426G-A standards compliance G-2426G-A indoor ONTs are compliant with the following standards:

CE marking for European standards for health, safety, and environmental protection EN 300-328 v1.9.1 wide band data transmission standards for 2.4GHz bands G.984 support GPON interface (framing) G.984.2 (Amd1, class B+) for GPON G.984.3 support for activation and password functions G.984.3 support for AES with operator enable/disable on per port-ID level G.984.3 support for dynamic bandwidth reporting G.984.3 support for FEC in both upstream and downstream directions G.984.3 support for multicast using a single GEM Port-ID for all video traffic G.984.4 and G.983.2 support for ONT management and provisioning IEEE 802.1p for traffic prioritization IEEE 802.1q for VLANs IEEE 802.3 (2012) IEEE 802.11 ac/b/g/n for Wi-Fi ITU-T G.711, G.722, G.723, G.726, G.729 SIP RFC 3261 September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 51 t f a r D t f a r D 52 G-2426G-A unit data sheet G-2426G-A standards compliance 7368 ISAM ONT 4.11.1 Energy-related products standby and off modes compliance Hereby, Nokia declares that the G-2426G-A ONTs are in compliance with the essential requirements and other relevant provisions of Directive 2009/125/EC together with Commission Regulation (EC) No 1275/2008 and Commission Regulation (EC) No 801/2013. The G-2426G-A ONTS qualify as equipment with high network availability (HiNA) functionality. Since the main purpose of G-2426G-A ONTs is to provide network functionality with HiNA 7 days

/24 hours, the modes Off/Standby, Power Management, and Networked Standby are inappropriate. For information about the type and number of network ports, see 4.5 G-2426G-A interfaces and interface capacity (p. 43) in this chapter. For information about power consumption, see 4.7 G-2426G-A detailed specifications (p. 47) in this chapter. 4.11.2 FCC statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 4.11.3 FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-

located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and 1. 2. this device must accept any interference received, including interference that may cause undesired operation. Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 G-2426G-A unit data sheet G-2426G-A special considerations CAUTION Service Disruption 7368 ISAM ONT D r a f t Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 4.12 G-2426G-A special considerations G-2426G-A is a package P ONT. 4.12.1 Wi-Fi service G-2426G-A indoor ONTs feature Wi-Fi service as well as voice and data services. Wi-Fi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE 802.11 standards, which the Wi-Fi Alliance defines as the basis for Wi-Fi technology. Wi-Fi physical features G-2426G-A indoor ONTs have the following physical features that assist in providing Wi-Fi service:

1 WLAN button for enabling and disabling Wi-Fi service 1 Wi-Fi Protected Setup (WPS) push button for adding WPS-enabled wireless devices The Wi-Fi service on G-2426G-A indoor ONTs supports the following IEEE standards and Wi-Fi Alliance certifications:

4 internal antennas: 2 for 2.4G and 2 for 5G Wi-Fi standards and certifications Certified for IEEE 802.11ac/b/g/n/standards WPA support including WPA-PSK Certified for WPA2-Personal Certified for WPA2-enterprise Wi-Fi GUI features G-2426G-A indoor ONTs have HTML-based Wi-Fi configuration GUIs. 4.12.2 G-2426G-A ONT considerations and limitations Table 4-15, G-2426G-A ONT considerations and limitations (p. 54) lists the considerations and limitations for Package P G-2426G-A ONTs. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 53 G-2426G-A unit data sheet G-2426G-A special considerations 7368 ISAM ONT Table 4-15 G-2426G-A ONT considerations and limitations Considerations and limitations Call History Data collection (ONTCALLHST) is supported, except for the following parameters: RTP packets (discarded), far-end RTCP and RTCP-XR participation, RTCP average and peak round trip delay, MOS, average jitter, number of jitter-buffer over-runs and under runs. Some voice features are configurable on a per ONT basis, including Call Waiting, Call Hold, 3-Way Calling, and Call Transfer. The following voice features / GSIP parameters are configurable on a per-Client/ per-ONT basis (not per-Subscriber):

Warmline timer is enabled per subscriber, but the warmline timer value is configured per ONT and must have a lower value than the Enable Caller ID and Enable Caller Name ID Digitmap and the associated Interdigit and Critical timers and Enter key parameters Permanent time Miscellaneous timers: Permanent, Timed-release, Reanswer, Error-tone, and CW-alert timers Features / functions: Message waiting mode, WMWI refresh interval, DTMF volume level Service Codes for the following features: CW, Call Hold and Warmline t f a r D t f a r D 54 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Install a G-2426G-A indoor ONT Overview 5 Install a G-2426G-A indoor ONT 7368 ISAM ONT D r a f t 5.1 Overview 5.1.1 Purpose 5.1.2 Contents 5.1 Overview 5.2 Purpose 5.3 General 5.4 Prerequisites 5.5 Recommended tools 5.6 Safety information 5.7 Procedure 5.2 Purpose 5.3 General 55 55 55 55 55 56 56 This chapter provides the steps to install a G-2426G-A indoor ONT. The steps listed in this chapter describe mounting and cabling for a G-2426G-A indoor ONT. 5.4 Prerequisites You need the following items before beginning the installation:

all required cables 5.5 Recommended tools You need the following tools for the installation:

#2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 55 Install a G-2426G-A indoor ONT Safety information 7368 ISAM ONT t f a r D drill and drill bits paper clip 5.6 Safety information DANGER Hazard Read the following safety information before installing the unit. Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits. Make sure all sources of power are turned off and have no live voltages present on feed lines or terminals. Use a voltmeter to measure for voltage before proceeding. Always contact the local utility company before connecting the enclosure to the utilities. This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. WARNING Equipment Damage CAUTION Service Disruption Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Note: Observe the local and national laws and regulations that may be applicable to this installation. Observe the following:

The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the Chapter 4, G-2426G-A unit data sheet for the temperature ranges of these ONTs. 5.7 Procedure Use this procedure to install a G-2426G-A indoor ONT. t f a r D 56 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 1 2 3 4 Install a G-2426G-A indoor ONT Procedure 7368 ISAM ONT D r a f t Place the indoor ONT unit on a flat surface, such as a desk or shelf. Note: The G-2426G-A cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are:

allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover Review the connection locations, as shown in Figure 5-1, G-2426G-A ONT connections

(p. 56). Figure 5-1 G-2426G-A ONT connections USB TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 POWER WLAN RESET ON/OFF WPS LED USB port POTS port

(RJ-11) Ethernet ports (4)

(RJ-45) Reset button Power Wi-Fi security/

on/off buttons On/off button 36176 Connect the Ethernet cables to the RJ-45 ports. Route the POTS cable directly to the RJ-11 port as per local practices. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 57 t f a r D t f a r D 58 Install a G-2426G-A indoor ONT Procedure 7368 ISAM ONT 5 6 7 8 9 10 11 DANGER Hazard WARNING Equipment Damage Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Be careful to maintain a bend radius of no less than 1.5 in. (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. Connect the fiber optic cable with SC/APC adapter to the SC/APC connector on the bottom of the ONT. Note: Fiber cable preparation varies depending on the type and size of the inside or outside plant fiber cable being spliced to the SC/APC fiber optic pigtail cable. Connect the power cable to the power connector. Power up the ONT unit by using the power switch. If used, enable the Wi-Fi service. for location of the WLAN button. a. Locate the WLAN button on the ONT; see Figure 5-1, G-2426G-A ONT connections (p. 57) b. Press the WLAN button to change the status of the Wi-Fi service. Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368 Hardware and Cabling Installation Guide. Activate and test the services; see the 7368 Hardware and Cabling Installation Guide. If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide. Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Install a G-2426G-A indoor ONT Procedure 12 If necessary, reset the ONT. ONT connections (p. 57). button to reset the ONT. END OF STEPS a. Locate the Reset button on a G-2426G-A indoor ONT as shown in Figure 5-1, G-2426G-A b. Insert the end of a straightened paper clip or other narrow object into the hole in the Reset 7368 ISAM ONT D r a f t September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 59 Install a G-2426G-A indoor ONT Procedure 7368 ISAM ONT t f a r D t f a r D 60 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Replace a G-2426G-A indoor ONT Overview 6 Replace a G-2426G-A indoor ONT 7368 ISAM ONT D r a f t 6.1 Overview 6.1.1 Purpose 6.1.2 Contents 6.1 Overview 6.2 Purpose 6.3 General 6.4 Prerequisites 6.5 Recommended tools 6.6 Safety information 6.7 Procedure 6.2 Purpose 6.3 General This chapter provides the steps to replace a G-2426G-A indoor ONT. The steps listed in this chapter describe mounting and cabling for a G-2426G-A indoor ONT. 6.4 Prerequisites You need the following items before beginning the installation:

all required cables 6.5 Recommended tools You need the following tools for replacing the ONT:

#2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA 61 61 61 61 61 62 62 D r a f t 61 t f a r D t f a r D 62 Replace a G-2426G-A indoor ONT Safety information 7368 ISAM ONT drill and drill bits 6.6 Safety information DANGER Hazard Read the following safety information before replacing the unit. Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits. Make sure all sources of power are turned off and have no live voltages present on feed lines or terminals. Use a voltmeter to measure for voltage before proceeding. Always contact the local utility company before connecting the enclosure to the utilities. WARNING Equipment Damage CAUTION Service Disruption This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Note: Observe the local and national laws and regulations that may be applicable to this installation. Observe the following:

The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the Chapter 4, G-2426G-A unit data sheet for the temperature ranges of these ONTs. 6.7 Procedure Use this procedure to replace a G-2426G-A indoor ONT. Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Replace a G-2426G-A indoor ONT Procedure 7368 ISAM ONT D r a f t 1 2 Deactivate the ONT services at the P-OLT. If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). a. Use the RTRV-ONT command to verify the ONT status and th associated services. Record the serial number or the SLID of the ONT displayed in the command output. RTRV-ONT::ONT-1-1-1-1-1;

b. If the ONT is in service, place the ONT in OOS state. Example:

Example:

ED-ONT::ONT-1-1-1-1-1;

If used, disable the Wi-Fi service by pressing the WLAN button; see Figure 6-1, G-2426G-A indoor ONT connections (p. 62) for the location of the WLAN button. Figure 6-1 G-2426G-A indoor ONT connections USB TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 POWER WLAN RESET ON/OFF WPS LED USB port POTS port

(RJ-11) Ethernet ports (4)

(RJ-45) Reset button Power Wi-Fi security/

on/off buttons On/off button 36176 September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 63 t f a r D t f a r D 64 Replace a G-2426G-A indoor ONT Procedure 7368 ISAM ONT Power down the unit by using the on/off power switch. Disconnect the POTS, Ethernet, and power cables from the ONT; see Figure 6-1, G-2426G-A indoor ONT connections (p. 63) for the connector locations on the G-2426G-A indoor ONT. 3 4 5 6 7 8 9 DANGER Hazard DANGER Hazard Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Disconnect the fiber optic cables. a. Unplug the fiber optic cable with SC/APC connector from the bottom of the ONT. b. Attach a fiber dust cover to the end of the SC/APC connector. Replace the old ONT with a new ONT on a flat surface, such as a desk or shelf. Connect the Ethernet cables directly to the RJ-45 ports; see Figure 6-1, G-2426G-A indoor ONT connections (p. 63) for the location of the RJ-45 ports. Connect the POTS cable directly to the RJ-11 port as per local practices; see Figure 6-1, G-

2426G-A indoor ONT connections (p. 63) for the location of the RJ-11 ports. Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide for more information about fiber optic handling, inspection, and cleaning. Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Replace a G-2426G-A indoor ONT Procedure 7368 ISAM ONT D r a f t 10 11 12 13 14 15 DANGER Hazard WARNING Equipment Damage Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Be careful to maintain a bend radius of no less than 1.5 in. (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. Connect the fiber optic cable with SC/APC adapter into the SC/APC connector on the bottom of the ONT. Note: Fiber cable preparation varies depending on the type and size of the inside or outside plant fiber cable being spliced to the SC/APC fiber optic pigtail cable. Connect the power cable to the power connector. Power up the unit by using the power switch. If used, enable the Wi-Fi service by pressing the WLAN button; see Figure 6-1, G-2426G-A indoor ONT connections (p. 63) for the location of the WLAN button. If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide for more information. Note: A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368 Hardware and Cabling Installation Guide. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 65 t f a r D 16 17 Replace a G-2426G-A indoor ONT Procedure 7368 ISAM ONT Activate and test the services; see the 7368 Hardware and Cabling Installation Guide. If necessary, reset the ONT. a. Locate the Reset button on a G-2426G-A indoor ONT as shown in Figure 6-1, G-2426G-A indoor ONT connections (p. 63). b. Insert the end of a straightened paper clip or other narrow object into the hole in the Reset button to reset the ONT. END OF STEPS t f a r D 66 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Overview 7 Configure a G-2426G-A indoor ONT 7368 ISAM ONT D r a f t 7.1 Overview 7.1.1 Purpose 7.1.2 Contents Viewing device information and connection status 7.1 Overview GUI configuration 7.2 General configuration 7.3 HGU mode GUI configuration 7.4 Log in to the web-based GUI 7.5 Overview 7.6 Viewing device information 7.7 Viewing LAN status 7.8 Viewing WAN status 7.9 Viewing WAN IPv6 status 7.10 Viewing home networking information 7.11 Viewing Optics module status 7.12 Viewing statistics 7.13 Viewing voice information Network configuration 7.14 Overview 7.15 Configuring LAN 7.16 Configuring LAN IPv6 7.17 Configuring WAN 7.18 Configuring WAN DHCP 7.19 Configuring Wireless 2.4GHz 7.20 Configuring Wireless 5GHz 7.21 Configuring wireless scheduling September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA 67 70 70 70 70 72 72 72 74 76 78 80 82 84 86 89 89 89 92 93 95 97 100 103 D r a f t 67 t f a r D t f a r D 68 Configure a G-2426G-A indoor ONT Overview 7368 ISAM ONT 7.22 Configuring IP routing 7.23 Configuring DNS 7.24 Configuring TR-069 7.25 Configuring GRE tunnel 7.26 Configuring Upstream (US) Classifier 7.27 Configuring QoS Security configuration 7.28 Overview 7.29 Configuring the firewall 7.30 Configuring the MAC filter 7.31 Configuring the IP filter 7.32 Configuring the URL filter 7.33 Configuring parental control 7.34 Configuring DMZ and ALG 7.35 Configuring access control Configuring the Application 7.36 Overview 7.37 Configuring port forwarding 7.38 Configuring port triggering 7.39 Configuring DDNS 7.40 Configuring NTP 7.41 Configuring USB 7.42 Configuring UPnP and DLNA 7.43 Configuring voice Maintenance 7.44 Overview 7.45 Configuring the password 7.46 WAN speed test 7.47 Speed test history 7.48 Configuring LOID 7.49 Configuring SLID 105 107 109 110 112 119 123 123 123 124 126 128 129 131 133 136 136 136 138 140 142 143 145 146 149 149 149 151 152 154 155 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Overview 7.50 Managing the device 7.51 Backing up the configuration 7.52 Restoring the configuration 7.53 Upgrading firmware 7.54 Rebooting the device 7.55 Resetting to factory defaults 7.56 Diagnosing WAN connections 7.57 Viewing log files RG Troubleshooting Counters 7.58 Overview 7.59 Viewing Residential Gateway (RG) troubleshooting counters 7368 ISAM ONT D r a f t 156 158 159 160 161 162 163 164 167 167 167 September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 69 Configure a G-2426G-A indoor ONT GUI configuration General configuration t f a r D GUI configuration 7.2 General configuration 7368 ISAM ONT Refer to the configuration information provided with your OLT for the software configuration procedure for a G-2426G-A ONT. For HTTP configuration procedures, please refer to the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide. 7.3 HGU mode GUI configuration Use the procedures below to use the web-based GUI for the G-2426G-A in HGU mode. This mode is preset at delivery. A home gateway unit (HGU) is a home networking device, used as a gateway to connect devices in the home through fiber to the Internet. An HGU provides a variety of features for the home network including routing and firewall capability. By using the HGU, users can connect all smart equipment in their home, including personal computers, set-top boxes, mobile phones, and other consumer electronics devices, to the Internet. The G-2426G-A ONTs support TLSv1.2 for WEBGUI (HTTPS). 7.4 Log in to the web-based GUI Use the procedure below to login to the web-based GUI for the G-2426G-A. 1 2 Open a web browser and enter the IP address of the ONT in the address bar. The Login page displays. The default gateway IP address must be same as the one printed on the device label. You can connect to this IP address using your web browser after connecting your PC to one of Ethernet ports of the ONT. The static IP address of your PC must be in the same default gateway subnet as the ONT. CAUTION Service Disruption Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID. Enter your username and password in the Login page. The default end-user account name and the default password for this account are printed on the device label. The superadmin account is meant for the Operator and is unique per device. Contact your Nokia representative to obtain the superadmin password based on the serial number on the device. t f a r D 70 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT GUI configuration Log in to the web-based GUI Figure 7-1 Web login page 7368 ISAM ONT D r a f t Note: If you forget the current username and password, press the reset button for 5 seconds and the default values for the username and password will be recovered at startup. 3 Click Login. The Device Information page displays. Note: To help protect the security of your Internet connection, the application displays a pop-up reminder to change both the Wi-Fi password and the ONT password. To increase password security, use a minimum of 10 characters, consisting of a mix of numbers and upper and lower case letters. END OF STEPS September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 71 Configure a G-2426G-A indoor ONT Viewing device information and connection status Overview 7368 ISAM ONT Viewing device information and connection status t f a r D 7.5 Overview 7.5.1 Purpose 7.5.2 Contents This chapter describes procedures to view device information and connection status on the G-2426G-A. 7.5 Overview 7.6 Viewing device information 7.7 Viewing LAN status 7.8 Viewing WAN status 7.9 Viewing WAN IPv6 status 7.10 Viewing home networking information 7.11 Viewing Optics module status 7.12 Viewing statistics 7.13 Viewing voice information 72 72 74 76 78 80 82 84 86 7.6 Viewing device information 1 Click StatusDevice Information from the left pane in the GPON Home Gateway page. The Device Information page displays the following information:

t f a r D 72 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing device information Figure 7-2 Device Information page 7368 ISAM ONT D r a f t Note: Upon login, the GPON Home Gateway window displays the WAN status block on the bottom left part of each window. This block shows the WAN connection ID, the WAN status, and any WAN errors. This block is accurate upon login, but it is static; click Refresh to update the information. Table 7-1 Device Information parameters Field Device Name Vendor Serial Number Description Name on the ONT Name of the vendor Serial number of the ONT Hardware version Hardware version of the ONT Boot version Boot version of the ONT Software version Software version of the ONT Chipset Chipset of the ONT September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 73 t f a r D Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing LAN status 7368 ISAM ONT Table 7-1 Device Information parameters (continued) Field Description Device Running Time Amount of time the device has run since last reset in hours, minutes, and seconds Click Refresh to update the displayed information. END OF STEPS 7.7 Viewing LAN status 2 1 Click StatusLAN Status from the left pane in the GPON Home Gateway page. The LAN Status page displays the following information:

t f a r D 74 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing LAN status Figure 7-3 LAN Status page 7368 ISAM ONT D r a f t September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 75 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing WAN status 7368 ISAM ONT t f a r D Wireless Information Wireless Status Wireless Channel SSID Name Wireless Rx Packets Wireless Tx Packets Wireless Rx Bytes Wireless Tx Bytes Ethernet Information Table 7-2 LAN Status parameters Field Description Wireless Encryption Status Encryption type used on the wireless connection Indicates whether the wireless is on or off Wireless channel number Name of each SSID Number of packets received on the wireless connection Number of packets transmitted on the wireless connection Number of bytes received on the wireless connection Number of bytes transmitted on the wireless connection Power Transmission (mW) Power of the wireless transmission, in mW Ethernet Status Indicates whether the Ethernet connection is on or off Ethernet IP Address IP address of the Ethernet connection Ethernet Subnet Mask Subnet Mask of the Ethernet connection Ethernet MAC Address MAC address of the Ethernet connection Ethernet Rx Packets Ethernet Tx Packets Ethernet Rx Bytes Ethernet Tx Bytes Number of packets received on the Ethernet connection Number of packets transmitted on the Ethernet connection Number of bytes received on the Ethernet connection Number of bytes transmitted on the Ethernet connection Click Refresh to display up-to-date information. END OF STEPS 7.8 Viewing WAN status 2 1 Click StatusWAN Status from the left pane in the GPON Home Gateway page. The WAN Status page displays the following information:

t f a r D 76 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing WAN status Figure 7-4 WAN Status page 7368 ISAM ONT D r a f t Table 7-3 WAN Status parameters Field Description WAN Connection List Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown. Connection Mode Connection mode of the WAN connection Enable/Disable Select this checkbox to enable or disable the WAN connection VLAN VLAN ID WAN Link Status Whether the WAN link is up or down IPv4 Address IP Address of the ONT Netmask Gateway Network mask Gateway address September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 77 7368 ISAM ONT t f a r D Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing WAN IPv6 status Table 7-3 WAN Status parameters (continued) Description Primary Domain Name Server Secondary Domain Name Server Manual Domain Name Server PON Link Status Whether the PON link is up or down Field Primary DNS Second DNS Manual DNS Tx Packets Rx Packets Tx Dropped Rx Dropped Err Packets Number of packets transmitted on the WAN connection Number of packets received on the WAN connection Number of packets dropped on the transmit WAN connection Number of packets dropped on the receive WAN connection Number of errored packets on the WAN connection Click Refresh to display up-to-date information. 7.9 Viewing WAN IPv6 status END OF STEPS 2 1 Click StatusWAN Status IPv6 from the left pane in the GPON Home Gateway page. The WAN Status IPv6 page displays the following information:

t f a r D 78 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing WAN IPv6 status Figure 7-5 WAN Status IPv6 page 7368 ISAM ONT D r a f t Table 7-4 WAN Status IPv6 parameters Field Description WAN Connection List Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown. Enable/Disable Select this checkbox to enable the WAN connection VLAN VLAN ID WAN Link Status Whether the WAN link is up or down IPv6 Address IPv6 Prefix IPv6 prefix IPv6 address that identifies the device and its location September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 79 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing home networking information 7368 ISAM ONT t f a r D Field IPv6 Gateway Primary DNS Second DNS Tx Packets Rx Packets Tx Dropped Rx Dropped Err Packets Table 7-4 WAN Status IPv6 parameters (continued) Description IPv6 gateway address Primary Domain Name Server Secondary Domain Name Server PON Link Status Whether the PON link is up or down Number of packets transmitted on the WAN connection Number of packets received on the WAN connection Number of packets dropped on the transmit WAN connection Number of packets dropped on the receive WAN connection Number of errored packets on the WAN connection Click Refresh to display up-to-date information. 7.10 Viewing home networking information END OF STEPS 2 1 Click StatusHome Networking from the left pane in the GPON Home Gateway page. The Home Networking page displays the following information:

t f a r D 80 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing home networking information Figure 7-6 Home Networking page 7368 ISAM ONT D r a f t September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 81 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing Optics module status 7368 ISAM ONT t f a r D Table 7-5 Home Networking parameters Field Description Table displays the number of Ethernet connections and their settings Table displays the number of wireless connections and their settings (2.4GHz and 5GHz) Wireless Settings (2.4GHz and 5GHz) Network Name Name of the wireless network Access Point Hexadecimal address of the wireless access point Each entry indicates the status (active or inactive), connection type, device name, IP address, hardware address, IP address allocation, lease remaining, and last active time of each connected local device. Table entry Shows the domain name, WAN name, number of IPs, IP range, and LAN list. Click Delete to delete a particular local device connection. Click Refresh to display up-to-date information. 7.11 Viewing Optics module status Click StatusOptics Module Status from the left pane in the GPON Home Gateway page. The Optics Module Status page displays the following information:

Local Interface Ethernet Wireless Local Devices Table entry Routing Domain Details You can:

END OF STEPS 1 t f a r D 82 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing Optics module status Figure 7-7 Optics Module Status page 7368 ISAM ONT D r a f t Table 7-6 Optics Module Status parameters Field Description Laser Bias Current (ONT ANI-ONT-Side Optical Measurements) Laser bias current, measured in uA Optics Module Voltage (ONT ANI-ONT-Side Optical Measurements) Optics module voltage, measured in V Optics Module Temperature (ONT ANI-ONT-Side Optical Measurements) Optics module temperature, measured in C Rx Optics Signal Level at 1490 nm (ONT ANI-ONT-Side Optical Measurements) Received optics signal level at 1490 nm, measured in dBm Tx Optics Signal Level at 1310 nm (ONT ANI-ONT-Side Optical Measurements) Transmitted optics signal level at 1310 nm, measured in dBm Lower (ONT ANI-ONT-Side Optical Measurements-Optical Threshold) Lower optical threshold, measured in dBm Upper (ONT ANI-ONT-Side Optical Measurements-Optical Threshold) Upper optical threshold, measured in dBm September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 83 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing statistics 7368 ISAM ONT t f a r D Click Refresh to display up-to-date information. END OF STEPS 7.12 Viewing statistics 2 1 Click StatusStatistics from the left pane in the GPON Home Gateway page. The Statistics page displays. Statistics are available for LAN ports, WAN ports, and WLAN ports. Select the LAN tab, WAN tab or WLAN tab to view the respective ports. Figure 7-8 LAN Statistics page t f a r D 84 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing statistics Figure 7-9 WAN Statistics page 7368 ISAM ONT D r a f t September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 85 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing voice information 7368 ISAM ONT t f a r D Figure 7-10 WLAN Statistics page 7.13 Viewing voice information END OF STEPS 1 Click StatusVoice Information from the left pane in the GPON Home Gateway page. The Voice Information page displays the following information:

t f a r D 86 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing voice information Figure 7-11 Voice Information page 7368 ISAM ONT D r a f t Table 7-7 Voice Information parameters Field Line Line Status Select a line from the list. The default is Line 1. Depending on the line chosen, the line options are:

Description Up Initializing Registering Unregistering Error Testing Quiescent Disabled The default is Disabled Soft Switch Proxy IP address; blank if the line is not registered September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 87 t f a r D Field Phone number Register Status Register Error Reason Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing voice information 7368 ISAM ONT Table 7-7 Voice Information parameters (continued) Register Error Code SIP standard error code for the register status; for example, 401, 403, 503 Description Phone number configured for a telephone line 1; For example, +13290611266 The default is Registered Blank if no voice service is provisioned This field is blank if the register is set to OK SIP standard error reason for the register status This field is blank if the register is set to OK User Agent IP IP address of the user agent ExternalIPAddress in WANIPConnection or WANPPPConnection Click Refresh to display up-to-date information. 2 END OF STEPS t f a r D 88 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 This chapter describes the network configuration tasks supported by G-2426G-A ONTs. Configure a G-2426G-A indoor ONT Network configuration Overview Network configuration 7.14 Overview 7.14.1 Purpose 7.14.2 Contents 7.14 Overview 7.15 Configuring LAN 7.16 Configuring LAN IPv6 7.17 Configuring WAN 7.18 Configuring WAN DHCP 7.19 Configuring Wireless 2.4GHz 7.20 Configuring Wireless 5GHz 7.21 Configuring wireless scheduling 7.22 Configuring IP routing 7.23 Configuring DNS 7.24 Configuring TR-069 7.25 Configuring GRE tunnel 7.26 Configuring Upstream (US) Classifier 7.27 Configuring QoS 7.15 Configuring LAN 1 7368 ISAM ONT D r a f t 89 89 92 93 95 97 100 103 105 107 109 110 112 119 Click NetworkLAN from the left pane in the GPON Home Gateway page. The LAN page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 89 Configure a G-2426G-A indoor ONT Network configuration Configuring LAN t f a r D Figure 7-12 LAN page 7368 ISAM ONT 2 Configure the following LAN parameters:

t f a r D 90 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t Configure a G-2426G-A indoor ONT Network configuration Configuring LAN Table 7-8 LAN parameters All Ports to Bridge Mode Select this checkbox to set all ports to bridge mode. Field Port Mode Port 1 - 4 IPv4 Address Subnet Mask DHCP enable Description Select the port mode for each port and click Save:

Route Mode Bridge Mode Enter the IP address of the ONT. Enter the subnet mask of the ONT. Select this checkbox to enable DHCP. DHCP Start IP Address Enter the starting DHCP IP address. DHCP End IP Address Enter the ending DHCP IP address. DHCP Lease Time Primary DNS Secondary DNS Enter the DHCP lease time (in min). Enter the primary DNS identifier. Enter the secondary DNS identifier. Configure the Static DHCP parameters:

Table 7-9 Static DHCP parameters Field Static DHCP Entry MAC Address IPv4 Address Description Enter the MAC address for the static DHCP. Enter the IPv4 address for the static DHCP. 3 4 5 6 Click Save. Click Save. Click Add. END OF STEPS You can also use this panel to delete a Static DHCP MAC address or IPv4 address. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 91 Configure a G-2426G-A indoor ONT Network configuration Configuring LAN IPv6 t f a r D 7.16 Configuring LAN IPv6 7368 ISAM ONT Click NetworkLAN_IPv6 from the left pane in the GPON Home Gateway page. The LAN_ IPv6 page displays. Figure 7-13 LAN IPv6 page 1 2 Configure the following parameters:

t f a r D 92 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t Configure a G-2426G-A indoor ONT Network configuration Configuring WAN Table 7-10 LAN IPv6 parameters Field Description IPv6 LAN Host Configuration DNS Server Prefix Config Interface DHCPv6 Server Pool Select a DNS server from the list. Select a prefix config option from the list, either WANConnection (prefix will be obtained from the WAN) or Static (enables you to enter the prefix). This field appears if you selected the Wan Connection option for the prefix config field. Select a WAN connection interface from the list. DHCP Start IP Address Enter the starting DHCP IP address. DHCP End IP Address Enter the ending DHCP IP address. Whether the address info through DCHP Whether other info obtained through DHCP Select this checkbox to enable address information retrieval through DHCP. Select this checkbox to enable retrieval of other information through DHCP. Maximum interval for periodic RA messages Enter the maximum interval (in seconds) for periodic Router Advertisement messages. The interval range is from 4 to 1800. Minimum interval for periodic RA messages Enter the minimum interval (in seconds) for periodic Router Advertisement messages. The interval range is from 4 to 1800. Click Save/Apply. END OF STEPS 7.17 Configuring WAN 3 1 Click NetworkWAN from the left pane in the GPON Home Gateway page. The WAN page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 93 Configure a G-2426G-A indoor ONT Network configuration Configuring WAN t f a r D Figure 7-14 WAN page 7368 ISAM ONT 2 Configure the following parameters:

Table 7-11 WAN parameters Field Description WAN Connection List Select a WAN connection from the list to set the connection parameters. Connection Type Select a connection type: IPoE or PPPoE. IP mode Select an IP mode from the list: IPv4 or IPv6. Enable/Disable Select this checkbox to enable the WAN connection. NAT Select this checkbox to enable NAT. t f a r D 94 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Network configuration Configuring WAN DHCP Table 7-11 WAN parameters (continued) Description Select the checkboxes to enable service types for this connection. Enable VLAN Select this checkbox to enable VLAN. Field Service VLAN ID VLAN PRI WAN IP Mode Manual DNS Enter the VLAN ID. Enter the VLAN PRI. Select an IP mode from the list. Enter the manual Domain Name Server. 7368 ISAM ONT D r a f t Click Save. END OF STEPS 3 1 7.18 Configuring WAN DHCP Click NetworkWAN DHCP from the left pane in the GPON Home Gateway page. The WAN DHCP page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 95 Configure a G-2426G-A indoor ONT Network configuration Configuring WAN DHCP t f a r D Figure 7-15 WAN DHCP page 7368 ISAM ONT 2 Configure the following parameters:

Table 7-12 WAN DHCP parameters Field Description WAN Connection List Select a WAN connection from the list. DHCP Option 50 Persistent Select this checkbox to enable DHCP Option 50 persistent. Enable DHCP Option 60 Select this checkbox to enable DHCP Option 60 (vendor class identifier). Enable DHCP Option 61 Select this checkbox to enable DHCP Option 61 (client identifier). Enable DHCP Option 77 Select this checkbox to enable DHCP Option 77. Enable DHCP Option 90 Select this checkbox to enable DHCP Option 90. t f a r D 96 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 2.4GHz Click Save. END OF STEPS 3 1 7.19 Configuring Wireless 2.4GHz 7368 ISAM ONT D r a f t Click NetworkWireless (2.4GHz) from the left pane in the GPON Home Gateway page. The Wireless (2.4GHz) page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 97 Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 2.4GHz t f a r D Figure 7-16 Wireless (2.4GHz) page 7368 ISAM ONT t f a r D 98 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 2.4GHz 2 Configure the following parameters:

Table 7-13 Wireless (2.4GHz) parameters Description Select this checkbox to enable Wi-Fi. Select a Wi-Fi mode from the list:

auto (b/g/n) Field Enable Mode Bandwidth b g n b/g g/n Select from:

20 MHz 40 MHz 20/40 MHz Low (25%) Medium (50%) High (75%) Maximum (100%) Channel Select a channel from the list or select Auto to have the channel automatically assigned. Transmitting Power Select a percentage for the transmitting power from the list:

WMM Select Enable or Disable from the list to enable or disable WiFi multimedia. Total MAX Users Enter the number of total MAX users. SSID Configuration SSID Select 1 Select the SSID from the list. SSID Name Enter the SSID name. Enable SSID Enable or disable SSID from this list. SSID Broadcast Enable or disable SSID broadcast from this list. Port Mode Isolation Select a port mode from the list. Route is the default. Enable or disable isolation from this list. MAX Users Enter the number of MAX users. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 99 7368 ISAM ONT Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 5GHz t f a r D Table 7-13 Wireless (2.4GHz) parameters (continued) Field Description Encryption Mode Select an encryption mode from the list:

WPA/WPA2 Personal WPA/WPA2 Enterprise WPA Version Select a WPA version from the list:

WPA Encryption Mode Select a WPA encryption mode from the list:

WEP OPEN WPA2 WPA/WPA2 AES TKIP/AES WPA Key Enter the WPA key. Enable WPS Select Enable or Disable from this list. WPS Mode Select a WPS mode from the list: PBC (Push Button Connect) or PIN (Personal Identification Number) Domain Grouping Select this checkbox to enable domain grouping. When enabled the fields Domain Name, WAN Interface, Number of IP, and LAN List become visible. To know more about configuring the fields, refer to the Domain Grouping section of Table 7-14, Wireless (5GHz) parameters (p. 102). Notes:

1. When the SSID select, SSID name, password and encryption mode is configured same between 2.4GHz and 5GHz network, the band steering feature is enabled. If you have enabled and configured WPS, click WPS connect. Click Save. END OF STEPS 3 4 1 7.20 Configuring Wireless 5GHz Click NetworkWireless (5GHz) from the left pane in the GPON Home Gateway page. The Wireless (5GHz) page displays. t f a r D 100 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 5GHz Figure 7-17 Wireless (5GHz) page 7368 ISAM ONT D r a f t 2 Configure the following parameters:

September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 101 7368 ISAM ONT Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 5GHz Table 7-14 Wireless (5GHz) parameters t f a r D Field Enable Bandwidth Select this checkbox to enable WiFi. Description Select from:

20 MHz 40 MHz 80 MHz Low (25%) Medium (50%) High (75%) Maximum (100%) Channel Select a channel from the list or select Auto to have the channel automatically assigned. Transmitting Power Select a percentage for the transmitting power from the list:

WMM Select Enable or Disable from the list to enable or disable WiFi multimedia. Total MAX Users Enter the total number of MAX users. SSID Configuration SSID Select 1 SSID Name Enable SSID Select the SSID from the list. Change the name of the selected SSID. Select Enable or Disable SSID from this list. SSID Broadcast Select Enable or Disable SSID broadcast from this list. Port Mode Isolation MAX Users Select a port mode from the list. Route is the default. Enable or disable isolation from this list. Enter the number of MAX users. Encryption Mode Select an encryption mode from the list:

WPA2-AES WPA2+WPA WPA/WPA2 Enterprise NONE-OPEN Enter the WPA key. Select Enable or Disable from this list. Select a WPS mode from the list: PBC (Push Button Connect) or PIN (Personal Identification Number) Select this checkbox to enable domain grouping. The fields Domain Name, Create One New Domain, WAN Interface, Number of IPs and List LAN are available when the Domain Grouping field is enabled. Domain Name Select a domain name from the list. Create One New Domain Select this checkbox to create a new domain. WPA Key Enable WPS WPS Mode Domain Grouping Domain Grouping t f a r D 102 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Network configuration Configuring wireless scheduling Table 7-14 Wireless (5GHz) parameters (continued) Field Description WAN Interface Select a WAN interface from the list Number of IP Select the number of IPs connected to the domain. LAN List Select one or more checkboxes. Notes:

7368 ISAM ONT D r a f t 1. When the SSID select, SSID name, password and encryption mode is configured same between 2.4GHz and 5GHz network, the band steering feature is enabled. If you have enabled and configured WPS, click WPS connect. Click Save. END OF STEPS 3 4 1 7.21 Configuring wireless scheduling Click NetworkWireless Schedule from the left pane in the GPON Home Gateway page. The Wireless Schedule page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 103 Configure a G-2426G-A indoor ONT Network configuration Configuring wireless scheduling t f a r D Figure 7-18 Wireless Schedule page 7368 ISAM ONT 2 3 4 5 Select the Schedule Function checkbox to turn the wireless signal off for the configured period. Click the plus sign (+) to add a scheduling rule. A separate panel displays for configuring wireless schedule rules. Enter a start time and end time for the period in which you want the wireless signal off. Select Everyday or Individual Days from the list. t f a r D 104 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t If you select Individual Days, select the checkboxes for the desired days. The Recurrence Pattern shows the rules created to date. If desired, click the plus sign (+) to add more rules. Configure a G-2426G-A indoor ONT Network configuration Configuring IP routing 6 7 8 1 Click Save Changes. END OF STEPS 7.22 Configuring IP routing Click NetworkIP Routing from the left pane in the GPON Home Gateway page. The IP Routing page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 105 Configure a G-2426G-A indoor ONT Network configuration Configuring IP routing t f a r D Figure 7-19 IP Routing page 7368 ISAM ONT 2 Configure the following parameters:

Table 7-15 IP Routing network parameters Field Description Enable Routing Select this checkbox to enable routing. Destination IP Address Enter the destination IP address. Destination Netmask Enter the destination network mask. Gateway Enter the gateway address. t f a r D 106 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Network configuration Configuring DNS Table 7-15 IP Routing network parameters (continued) Field Description IPv4 Interface Select a WAN connection previously created in the WAN page from the list. Forwarding Policy Select a forwarding policy from the list. 7368 ISAM ONT D r a f t Click Add. END OF STEPS 3 1 7.23 Configuring DNS Click NetworkDNS from the left pane in the GPON Home Gateway page. The DNS page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 107 Configure a G-2426G-A indoor ONT Network configuration Configuring DNS t f a r D Figure 7-20 DNS page 7368 ISAM ONT 2 Configure the following parameters:

Table 7-16 DNS parameters Field DNS Proxy Domain Name IPv4 Address Origin Domain Description Select the Enabled checkbox to enable DNS proxy and click Save. Enter the domain name. Enter the domain IP address and click Add. Enter the origin domain name. t f a r D 108 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Network configuration Configuring TR-069 Table 7-16 DNS parameters (continued) Field Description 7.24 Configuring TR-069 END OF STEPS 1 New Domain Associate an origin domain with a new domain and click Add. 7368 ISAM ONT D r a f t Click NetworkTR-069 from the left pane in the GPON Home Gateway page. The TR-069 page displays. Figure 7-21 TR-069 page September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 109 7368 ISAM ONT Configure a G-2426G-A indoor ONT Network configuration Configuring GRE tunnel t f a r D Configure the following parameters:

Table 7-17 TR-069 parameters Field Description Periodic Inform Enable Select this checkbox to enable periodic inform updates. Periodic Inform Interval(s) Enter the time between periodic inform updates, in seconds. URL Username Password Enter the URL of the auto-configuration server. Enter the username to log in to the auto-configuration server. Enter the password to log in to the auto-configuration server. Connect Request Username Enter the username to log in to the ONT. Connect Request Password Enter the password to log in to the ONT. Click Save. END OF STEPS 7.25 Configuring GRE tunnel 2 3 1 Click NetworkGRE Tunnel from the left pane in the GPON Home Gateway page. The GRE Tunnel page displays. t f a r D 110 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Network configuration Configuring GRE tunnel Figure 7-22 GRE Tunnel page 7368 ISAM ONT D r a f t 2 Configure the following parameters:

Table 7-18 GRE Tunnel parameters Field Tunnel Name WAN Interface Description Select Create new GRE Tunnel or select an existing tunnel from the list. The tunnel name is automatically assigned by the system. Up to 3 GRE tunnels are supported. Select a WAN interface from the list. GRE tunnels can only be created on HSI-enabled WAN interfaces. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 111 7368 ISAM ONT Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier t f a r D Table 7-18 GRE Tunnel parameters (continued) Field Description Primary Remote End Secondary Remote End (optional) Enter an IP address or FQDN that is unique in the system. If the primary remote endpoint is down or unreachable, the secondary remote endpoint becomes active, if configured. The secondary remote endpoint remains active until it becomes unreachable, in which case the primary remote endpoint becomes active again. Revertive mode is not supported. If both endpoints are unreachable, the GRE tunnel is declared down. Connected Remote End This field displays the current data traffic path for the GRE tunnel. Connectivity check This feature is automatically selected by the system. Traffic timeout to start pings Enter the traffic timeout in seconds (2 to 1024). No. of retries before unreachable Enter the number of retries before the tunnel is declared down (0 to 100). 3 Click Save. END OF STEPS 7.26 Configuring Upstream (US) Classifier The US Classifier feature is used to create policies, classifiers, and classifier rules for upstream traffic handling. This feature is available to admin users (super users) only. A policy defines an action to be performed on a set of LAN or WAN packets. A policy can be created at any time and then subsequently assigned to one or more classifiers. A classifier is used to select key fields for which the classifier rules will be written. A classifier can be created at any time and then subsequently assigned to one or more classifier rules. A classifier rule is used to assign actions to a group of packets based on a set of parameters. A classification rule must be created against a pre-defined classifier. Up to 16 policies can be created, with up to 8 classifiers and 32 classifier rules. 1 Click NetworkUS Classifier from the left pane in the GPON Home Gateway page. The US Classifier page displays. t f a r D 112 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier Figure 7-23 US Classifier 7368 ISAM ONT D r a f t 2 Select the Policy tab. All classifier policies are displayed in the policy table in the page. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 113 Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier t f a r D Figure 7-24 US Classifier- Policy page 7368 ISAM ONT 3 Configure the following parameters:

Table 7-19 US Classifier Policy parameters Tunnel Interface Select a tunnel interface from the list: No Tunnel, GRE Tunnel, or LAN traffic. Description The tunnel type is set to GRE and cannot be modified. Enter a VLAN ID (0-4094). This field is not configurable. The VLAN tag is set to 8100 (hexadecimal). Enter a VLAN priority level (0 to 7). A lower number indicates a higher priority. Field Tunnel Type VLAN ID VLAN Tag VLAN Priority t f a r D 114 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier Table 7-19 US Classifier Policy parameters (continued) IP TOS/DSCP Field Drop Description This field is not configurable. All tunnel packets are generated with a default DSCP value

(usually 0). Select this checkbox to drop the packets. Click Save. 4 5 6 To delete a policy, click Delete for the applicable policy in the policy table. A policy can only be deleted if it is not associated with any classifier rules. Click NetworkUS Classifier from the left pane in the GPON Home Gateway page and select the Classifier tab. All classifiers are displayed in the classifier table in the page. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 115 Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier t f a r D Figure 7-25 US Classifier- Classifier page 7368 ISAM ONT 7 Configure the following parameters:

At least one field must be selected to create a classifier. A maximum of four fields may be selected to create a classifier; this includes the interface field. Table 7-20 US Classifier parameters Description Select an interface from the list; for example, None, LAN, 2.4G SSID, or 5G SSID. Click to enter a source MAC address. Click to enter a destination MAC address. Click to enter a source IP address. Field Interface Source MAC Destination MAC Source IP t f a r D 116 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier Table 7-20 US Classifier parameters (continued) Field Destination IP Source Port Destination Port Protocol Priority Description Click to enter a destination IP address. Click to enter a source port. Click to enter a destination port. Click to enter a protocol. 7368 ISAM ONT D r a f t Select a priority level from 1 to 8. The lower the number, the higher the priority. No more than 1 classifier can be created with the same priority. Click Save. 8 9 10 To delete a classifier, click Delete for the applicable classifier in the classifier table. A classifier can only be deleted if it is not associated with any classifier rules. Expand Classifier Rules. All classifier rules are displayed in the classifier rules table in the page. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 117 Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier t f a r D Figure 7-26 US Classifier Rules page 7368 ISAM ONT 11 Configure the classifier rule. Table 7-21 US Classifier Rules parameters Field Policy Classifier Interface Source MAC Destination MAC t f a r D 118 Description Select a policy from the list. Select a classifier from the list. Enter a source MAC address. Enter a destination MAC address. Select an interface from the list; for example, None, LAN, 2.4G SSID, 5G SSID. Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Network configuration Configuring QoS Table 7-21 US Classifier Rules parameters (continued) 7368 ISAM ONT D r a f t Description Enter a source IP address. Enter a destination IP address. Enter a source port address. Enter a destination port address. Enter a value between 0 and 254. Field Source IP Destination IP Source Port Destination Port IP Protocol Type 12 13 1 Click Save. END OF STEPS 7.27 Configuring QoS To delete a classifier rule, click Delete for the applicable classifier rule in the classifier rules table. Click NetworkQoS Config from the left pane in the GPON Home Gateway page. The QoS Config page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 119 Configure a G-2426G-A indoor ONT Network configuration Configuring QoS t f a r D Figure 7-27 QoS Config page (L2 packet sizes) 7368 ISAM ONT t f a r D 120 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Network configuration Configuring QoS Figure 7-28 QoS Config page (L3 packet sizes) 7368 ISAM ONT D r a f t September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 121 Configure a G-2426G-A indoor ONT Network configuration Configuring QoS t f a r D 2 Configure the following parameters:

7368 ISAM ONT Table 7-22 QoS Config parameters Description QoS Setting Field Type Classification Criteria Source MAC Select a QoS service layer type from the list: L2 or L3. Enter the source MAC Select the Exclude checkbox to exclude the source MAC address. Interface Select an interface from the list. Classification Result DSCP Remark Enter the value for the DSCP mark (range: 0-63); valid only for L3 Criteria. 802.1p Remark Enter the value for the 802.1p (range: 0-7). Forwarding Policy Enter the number for the forwarding policy (range: 1-7). Additional fields for L3 Protocol Application Source IP and Source IP Mask Destination IP and Destination IP Mask Source Port and Source Port Max Select a protocol from the list, or select the Exclude checkbox. Select an application from the list. Enter the values for the source IP and IP mask, or select the Exclude checkbox. Enter the values for the destination IP and IP mask, or select the Exclude checkbox. Enter the values for the source port and port max (highest port number) or select the Exclude checkbox. Destination Port and Destination Port Max Enter the values for the destination port and port max (highest port number), or select the Exclude checkbox. Click Add to add a QoS policy. 3 END OF STEPS t f a r D 122 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 This chapter describes the security configuration tasks supported by G-2426G-A ONTs Configure a G-2426G-A indoor ONT Security configuration Overview Security configuration 7.28 Overview 7.28.1 Purpose 7.28.2 Contents 7.28 Overview 7.29 Configuring the firewall 7.30 Configuring the MAC filter 7.31 Configuring the IP filter 7.32 Configuring the URL filter 7.33 Configuring parental control 7.34 Configuring DMZ and ALG 7.35 Configuring access control 7368 ISAM ONT D r a f t 123 123 124 126 128 129 131 133 7.29 Configuring the firewall 1 Click SecurityFirewall from the left pane in the GPON Home Gateway page. The Firewall page displays. Figure 7-29 Firewall page September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 123 7368 ISAM ONT Configure a G-2426G-A indoor ONT Security configuration Configuring the MAC filter t f a r D Configure the following parameters:

Table 7-23 Firewall parameters Field Security level Description Click Save. END OF STEPS 7.30 Configuring the MAC filter 2 3 1 Select the security level from the list:

High: Traffic denied inbound and minimally permit common services outbound Low: All outbound traffic and pinhole-defined inbound traffic is allowed Off: All inbound and outbound traffic is allowed Attack Protect (Protection against DoS or DDoS attacks) Select Enable or Disable from the list. The default is Enable. Click SecurityMAC Filter from the left pane in the GPON Home Gateway page. The MAC Filter page displays. t f a r D 124 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Security configuration Configuring the MAC filter Figure 7-30 MAC Filter page 7368 ISAM ONT D r a f t September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 125 7368 ISAM ONT Configure a G-2426G-A indoor ONT Security configuration Configuring the IP filter t f a r D Table 7-24 MAC Filter parameters Field Description Ethernet Interface Configure the following parameters:

MAC Filter Mode Select the MAC filter mode from the list: Blocked or Allowed. LAN Port Enter the LAN port range. MAC Address Select the MAC address from the list or enter the address in the text field. Wi-Fi SSID MAC Filter Mode Select the MAC filter mode from the list: Blocked or Allowed SSID Select Select the SSID from the list. Enable Select this checkbox to enable the MAC filter. MAC Address Select a MAC address from the list or enter the address in the text field. Click Save. You can:

END OF STEPS Click Select Allto select all the Mac Address records displayed. Click Delete to delete MAC Address. Click Refreshto display the up-to-date information. 7.31 Configuring the IP filter 2 3 1 Click SecurityIP Filter from the left pane in the GPON Home Gateway page. The IP Filter page displays. t f a r D 126 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Security configuration Configuring the IP filter Figure 7-31 IP Filter page 7368 ISAM ONT D r a f t 2 Configure the following parameters:

Table 7-25 IP Filter parameters Enable IP Filter Select this checkbox to enable an IP filter. Field Mode Description Select an IP filter mode from the list:

Drop for upstream Drop for downstream Internal Client Select an internal client from the list:

Custom settings - uses the IP address input below IP - uses the connecting devices' IP to the ONT Local IP Address Enter the local IP address. Source Subnet Mask Enter the source subnet mask. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 127 7368 ISAM ONT Configure a G-2426G-A indoor ONT Security configuration Configuring the URL filter t f a r D Table 7-25 IP Filter parameters (continued) Field Description Remote IP Address Enter the remote IP address. Destination Subnet Mask Enter the destination subnet mask. Protocol Select an application protocol or ALL from the list. Click Add. END OF STEPS 3 1 7.32 Configuring the URL filter Click SecurityURL Filter from the left pane in the GPON Home Gateway page. The URL Filter page displays. Figure 7-32 URL Filter page t f a r D 128 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t Configure a G-2426G-A indoor ONT Security configuration Configuring parental control Configure the following parameters:

Table 7-26 URL Filter parameters Field Description Enable URL filter Select the checkbox to enable the URL filter. Select the option to block the URL or allow the URL. URL filter type URL List URL Address Port - default to 80 Enter the port number; the default is 80. Enter the URL address. Click Add Filter. END OF STEPS 7.33 Configuring parental control 2 3 1 Note: You cannot use URL filtering for HTTPS. The URL is encrypted when using HTTPS. Click SecurityParent Control from the left pane in the GPON Home Gateway page. The Parental Control page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 129 Configure a G-2426G-A indoor ONT Security configuration Configuring parental control t f a r D Figure 7-33 Parental Control page 7368 ISAM ONT Select the Access Control checkbox. Click the plus sign (+) to add a policy. A separate panel displays for configuring the policy name, IP address of the device, and dates and times for the policy. 2 3 4 Configure the following parameters:

Table 7-27 Parental Control parameters Field Description Access Control Select this checkbox to enable access control. Add Access Control rule t f a r D 130 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Security configuration Configuring DMZ and ALG Table 7-27 Parental Control parameters (continued) Field Description Policy Name Enter a name for the parental control policy or select a policy from the list. MAC Address Enter the MAC address or select a MAC address from the list. IPv4 Address Enter the IPv4 address for the device or select an IPv4 address from the list. Url Port Enter the URL port for the device. Days of week Select Everyday, or Individual Days and select the checkboxes for the days of the week for which the policy applies. 7368 ISAM ONT D r a f t From To Enter the time for the policy to be in effect. Click Save changes. Click Enable to activate the policy. END OF STEPS 7.34 Configuring DMZ and ALG 5 6 1 Click SecurityDMZ and ALG from the left pane in the GPON Home Gateway page. The DMZ and ALG page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 131 Configure a G-2426G-A indoor ONT Security configuration Configuring DMZ and ALG t f a r D Figure 7-34 DMZ and ALG page 7368 ISAM ONT Configure the following parameters:

Table 7-28 ALG parameters Description Field ALG Config DMZ Config Select the checkboxes to enable the protocols to be supported by the ALG: FTP, TFTP, SIP, H323, RTSP, L2TP, IPSEC, PPTP. WAN Connection List Select a WAN connection from the list. Enable DMZ Select this checkbox to enable DMZ on the chosen WAN connection. DMZ IP Address Select Custom Settings and enter the DMZ IP address or select the IP address of a connected device from the list. 2 3 Click Save ALG. t f a r D 132 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t Configure a G-2426G-A indoor ONT Security configuration Configuring access control Configure the following parameters:

Table 7-29 DMZ parameters Description Field ALG Config DMZ Config Select the checkboxes to enable the protocols to be supported by the ALG: FTP, TFTP, SIP, H323, RTSP, L2TP, IPSEC, PPTP. WAN Connection List Select a WAN connection from the list. Enable DMZ Select this checkbox to enable DMZ on the chosen WAN connection. DMZ IP Address Select Custom Settings and enter the DMZ IP address or select the IP address of a connected device from the list. Click Save DMZ. END OF STEPS 7.35 Configuring access control This procedure describes how to configure the access control level (ACL). Note: ACL takes precedence over the firewall policy. The trusted network object will be shared for all WAN connections; it is not applied individually to a WAN connection. Click SecurityAccess Control from the left pane in the GPON Home Gateway page. The Access Control page displays. 4 5 1 September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 133 Configure a G-2426G-A indoor ONT Security configuration Configuring access control t f a r D Figure 7-35 Access Control page 7368 ISAM ONT 2 Configure the following parameters:

Table 7-30 Access Control parameters Field WAN Description Select a connection from the list. Trusted Network Enable Click to enable or disable trusted network. t f a r D 134 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Security configuration Configuring access control Table 7-30 Access Control parameters (continued) Field Description ICMP, Telnet, SSH, HTTP, TR-069, HTTPS, SFTP Select an access control level for each protocol:

WAN side: Allow, Deny, or Trusted Network Only LAN side: Allow or Deny 7368 ISAM ONT D r a f t Optionally, add one or more subnet trusted networks. The maximum number of entries is 32. You can also use the Source IP fields to delete a previously created entry for a subnet trusted network. Table 7-31 Trusted Network parameters Field Source IP Start Source IP End Description Enter a start IP address for the new subnet trusted network. Enter an end IP address for the new subnet trusted network. Click Save. 3 4 5 Click Add. END OF STEPS September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 135 Configure a G-2426G-A indoor ONT Configuring the Application Overview t f a r D Configuring the Application 7368 ISAM ONT This chapter describes the application configuration tasks supported by the G-2426G-A ONTs. 7.36 Overview 7.36.1 Purpose 7.36.2 Contents 7.36 Overview 7.37 Configuring port forwarding 7.38 Configuring port triggering 7.39 Configuring DDNS 7.40 Configuring NTP 7.41 Configuring USB 7.42 Configuring UPnP and DLNA 7.43 Configuring voice 136 136 138 140 142 143 145 146 7.37 Configuring port forwarding 1 Click ApplicationPort Forwarding from the left pane in the GPON Home Gateway page. The Port Forwarding page displays. t f a r D 136 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Configuring the Application Configuring port forwarding Figure 7-36 Port Forwarding page 7368 ISAM ONT D r a f t 2 Configure the following parameters:

Table 7-32 Port Forwarding parameters Field Description Application Name Select an application name from the list The default is Custom settings. WAN Port LAN Port Enter the WAN port range. Enter the LAN port range. Internal Client Select a connected device from the list and enter the associated IP address. Protocol Select the port forwarding protocol from the list:

TCP UDP TCP/UDP September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 137 7368 ISAM ONT Configure a G-2426G-A indoor ONT Configuring the Application Configuring port triggering t f a r D Table 7-32 Port Forwarding parameters (continued) Field Description Enable Mapping Select this checkbox to enable mapping. WAN Connection List Select a WAN connection from the list. Note: Only active devices are shown on this list. Click Add. END OF STEPS 3 1 7.38 Configuring port triggering Click ApplicationPort Triggering from the left pane in the GPON Home Gateway page. The Port Triggering page displays. t f a r D 138 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Configuring the Application Configuring port triggering Figure 7-37 Port Triggering page 7368 ISAM ONT D r a f t 2 Configure the following parameters:

Table 7-33 Port Triggering parameters Field Description Application Name Select an application name from the list. The default is Custom settings. Open Port Enter the open port range. Triggering Port Enter the triggering port range. Expire Time Enter the expiration time in seconds. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 139 7368 ISAM ONT Configure a G-2426G-A indoor ONT Configuring the Application Configuring DDNS t f a r D Table 7-33 Port Triggering parameters (continued) Field Description Open Protocol Select the open port protocol from the list:

TCP UDP TCP/UDP TCP UDP TCP/UDP Trigger Protocol Select the triggering port protocol from the list:

Enable Triggering Select this checkbox to enable port triggering. WAN Connection List Select a WAN connection from the list. Note: Only active devices are shown on this list. Click Add. END OF STEPS 3 1 7.39 Configuring DDNS Click ApplicationDDNS from the left pane in the GPON Home Gateway page. The DDNS page displays. t f a r D 140 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Configuring the Application Configuring DDNS Figure 7-38 DDNS page 7368 ISAM ONT D r a f t WAN Connection List Select a WAN connection from the list. Enable DDNS Select this checkbox to enable DDNS on the chosen WAN connection. 2 Configure the following parameters:

Table 7-34 DDNS parameters Description Field ISP Username Password DDNS Status Domain Name Enter the domain name. Select an ISP from the list. Enter the username. Enter the password. Displays the status of the DDNS: Synchronized, Synchronization failed, or blank if no update message has been received from the ISP. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 141 Configure a G-2426G-A indoor ONT Configuring the Application Configuring NTP t f a r D Click Save. END OF STEPS 7.40 Configuring NTP 7368 ISAM ONT Click ApplicationNTP from the left pane in the GPON Home Gateway page. The NTP page displays. Figure 7-39 NTP page 3 1 2 Configure the following parameters:

t f a r D 142 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Configuring the Application Configuring USB Table 7-35 NTP parameters Field Description 7368 ISAM ONT D r a f t Enable NTP Service Select this checkbox to enable the NTP service. Current Time Enter the current local date and time. Primary Time Server Select a time server from the list or choose Customer setting and enter the address of the time server. Secondary Time Server Select a time server from the list or choose Customer setting and enter the address of the time server. Third Time Server Interval Time Time Zone Select a time server from the list or choose Customer setting and enter the address of the time server. Enter the interval at which to get the time from the time server, in seconds. Select the local time zone from the list. Click Save. END OF STEPS 7.41 Configuring USB 3 1 You can connect USB storage devices and USB printers to the USB ports of the device. The USB menu enables you to configure FTP and SFTP for your USB storage devices. The USB connected devices are shown in overview table on the bottom of the USB window. Click ApplicationUSB from the left pane in the GPON Home Gateway page. The USB page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 143 Configure a G-2426G-A indoor ONT Configuring the Application Configuring USB t f a r D Figure 7-40 USB page 7368 ISAM ONT 2 Configure the following parameters:

Table 7-36 USB parameters Field Description Enable FTP server Select this checkbox to enable using an FTP server t f a r D 144 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t Configure a G-2426G-A indoor ONT Configuring the Application Configuring UPnP and DLNA Table 7-36 USB parameters (continued) Description Enter the username for the FTP server. Enter the password for the FTP server. Field Username Password Username Password Username Password Re-enter Password Enter the password for the FTP server. Enable SFTP server Select this checkbox to enable using an SFTP server. Enable SFTP for Remote Access Select this checkbox to enable SFTP for remote access. Re-enter Password Enter the password for the SFTP server. Enable Printer Sharing Enter the username for the SFTP server. Enter the password for the SFTP server. Select this checkbox to enable printer sharing. Printer sharing is disabled by default Enter the username for the SFTP server. Enter the password for the SFTP server. Re-enter Password Enter the password for the SFTP server. Connected USB Devices Table For each printer that is connected to the ONT, the following fields are displayed:

Host Number for example: Printer1, Printer2 Device Name: name or identification for the USB device Format: displays the storage format (applies only to a USB storage device) Total space (applies only to a USB storage device) Free space (applies only to a USB storage device) Click Save. END OF STEPS 3 1 7.42 Configuring UPnP and DLNA Click ApplicationUPnP and DLNA from the left pane in the GPON Home Gateway page. The UPnP and DLNA page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 145 Configure a G-2426G-A indoor ONT Configuring the Application Configuring voice t f a r D Figure 7-41 UPnP and DLNA page 7368 ISAM ONT Select the Enable UPnP/DLNA checkbox to enable UPnP/DLNA. 2 3 1 Click Save/Apply. END OF STEPS 7.43 Configuring voice Click ApplicationVoice Setting from the left pane in the GPON Home Gateway page. The Voice Setting page displays. t f a r D 146 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Configuring the Application Configuring voice Figure 7-42 Voice Setting page 7368 ISAM ONT D r a f t September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 147 7368 ISAM ONT Configure a G-2426G-A indoor ONT Configuring the Application Configuring voice t f a r D 2 Configure the following parameters:

Table 7-37 Voice Setting parameters Field Voice Setting Description Outbound Proxy Enter the SIP outbound proxy. Outbound Proxy Port Enter the outbound proxy port. Proxy Server Enter the proxy server. Proxy Server Port Enter the proxy server port. Registrar Server Enter the registrar server. Registrar Server Port Enter the registrar server port. UserAgentDomain Enter the user agent domain. UserAgentPort Enter the user agent port. A string of characters with a length limit of 1024 bytes. A dial plan can consist of several dial plan tokens. Each token is a component of the overall dial plan. DigitMap DTMF Mode FaxT38 Line Setting POTS line Enable Select InBand, or RFC2833 from the list. Select False or True from the list. Select a POTS line from the list. Select Enabled or Disabled from the list. Directory Number Enter a directory number. AuthUserName Enter an authorized username. AuthPassword Enter a password for the user. URI Enter the Uniform Resource Identifier of the SIP URL. 3 Click Save. END OF STEPS t f a r D 148 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 This chapter describes the maintenance tasks supported by G-2426G-A ONTs. Configure a G-2426G-A indoor ONT Maintenance Overview Maintenance 7.44 Overview 7.44.1 Purpose 7.44.2 Contents 7.44 Overview 7.45 Configuring the password 7.46 WAN speed test 7.47 Speed test history 7.48 Configuring LOID 7.49 Configuring SLID 7.50 Managing the device 7.51 Backing up the configuration 7.52 Restoring the configuration 7.53 Upgrading firmware 7.54 Rebooting the device 7.55 Resetting to factory defaults 7.56 Diagnosing WAN connections 7.57 Viewing log files 7368 ISAM ONT D r a f t 149 149 151 152 154 155 156 158 159 160 161 162 163 164 7.45 Configuring the password A password must adhere to the password rules, which are as follows:

the password may consist of uppercase letters, lowercase letters, digital numbers, and the following special characters ! # + , - / @ _ : = ]

the password length must be from 8 to 24 characters the first character must be a digital number or a letter the password must contain at least two types of characters: numbers, letters, or special characters the same character must not appear more than 8 times in a row When the password meets the password rules, the application displays the message Your password has been changed successfully. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 149 Configure a G-2426G-A indoor ONT Maintenance Configuring the password t f a r D 7368 ISAM ONT When the password does not meet the password rules, the application displays a message to indicate which password rule has not been followed, for example:

the password is too short the password is too long the first character cannot be a special character there are not enough character classes 1 Click MaintenancePassword from the left pane in the GPON Home Gateway page. The Password page displays. Figure 7-43 Password page 2 Configure the following parameters:

t f a r D 150 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t New Password Enter the new password (must adhere to the password rules described above). Re-enter password Re-enter the new password (Must match the new password entered above exactly). Prompt message Enter the password prompt message. Configure a G-2426G-A indoor ONT Maintenance WAN speed test Table 7-38 Password parameters Field Description Original Password Enter the current password. Click Save. END OF STEPS 3 1 7.46 WAN speed test Click MaintenanceSpeed test from the left pane in the GPON Home Gateway page. The Speed Test page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 151 Configure a G-2426G-A indoor ONT Maintenance Speed test history t f a r D 7368 ISAM ONT Accept Ookla Privacy Policy as instructed in the Note displayed. Click Start to start the speed test. You can click Cancel to cancel the speed test. END OF STEPS 7.47 Speed test history 2 1 Click MaintenanceSpeed Test History from the left pane in the GPON Home Gateway page. The Speed History page displays. t f a r D 152 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Maintenance Speed test history Figure 7-44 Speed Test History 7368 ISAM ONT D r a f t September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 153 7368 ISAM ONT Configure a G-2426G-A indoor ONT Maintenance Configuring LOID t f a r D The history of speed test is displayed. You can click Refresh to display up-to-date information. END OF STEPS The history of the speed test is displayed. 7.48 Configuring LOID Click MaintenanceLOID Configuration from the left pane in the GPON Home Gateway page. The LOID Configuration page displays. Figure 7-45 LOID Configuration page 1 2 Configure the following parameters:

t f a r D 154 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Maintenance Configuring SLID Table 7-39 LOID Configuration parameters Field LOID Description Enter the LOID; the maximum number of characters is 24. If the password is null, this field may be left blank Password Enter the password; the maximum number of characters is 12. 7368 ISAM ONT D r a f t Click Save/Apply. END OF STEPS 7.49 Configuring SLID 3 1 Click MaintenanceSLID Configuration from the left pane in the GPON Home Gateway page. The SLID Configuration page displays. Figure 7-46 SLID Configuration page September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 155 7368 ISAM ONT Configure a G-2426G-A indoor ONT Maintenance Managing the device t f a r D Configure the following parameters:

Table 7-40 SLID Configuration parameters Field Description Current SLID Displays the current SLID. Enter New SLID Enter the new SLID. SLID Mode Select a SLID mode from the list. The default is HEX Mode. Click Save. END OF STEPS 7.50 Managing the device 2 3 1 Click MaintenanceDevice Management from the left pane in the GPON Home Gateway page. The Device Management page displays. t f a r D 156 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Maintenance Managing the device Figure 7-47 Device Management page 7368 ISAM ONT D r a f t Configure the following parameters:

Table 7-41 Device Management parameters Field Host Name Host Alias Description Select a hostname from the list. Enter an alias for the selected host. 2 3 Click Add. END OF STEPS September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 157 Configure a G-2426G-A indoor ONT Maintenance Backing up the configuration t f a r D 7.51 Backing up the configuration 1 7368 ISAM ONT Click MaintenanceBackup and Restore from the left pane in the GPON Home Gateway page. The Backup and Restore page displays. Figure 7-48 Backup and Restore page Click Export to export the current ONT configuration to a backup file. 2 END OF STEPS t f a r D 158 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 1 2 3 Configure a G-2426G-A indoor ONT Maintenance Restoring the configuration 7.52 Restoring the configuration 7368 ISAM ONT D r a f t Click MaintenanceBackup and Restore from the left pane in the GPON Home Gateway page. The Backup and Restore page displays. Figure 7-49 Backup and Restore page Click Choose file and select a backup file. Click Import to restore the ONT to the saved backup. END OF STEPS September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 159 1 2 3 Configure a G-2426G-A indoor ONT Maintenance Upgrading firmware t f a r D 7.53 Upgrading firmware 7368 ISAM ONT Click MaintenanceFirmware Upgrade from the left pane in the GPON Home Gateway page. The Firmware Upgrade page displays. Figure 7-50 Firmware Upgrade page Click Choose file and select the firmware file. Click Upgrade to upgrade the firmware. END OF STEPS t f a r D 160 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Maintenance Rebooting the device 7.54 Rebooting the device 1 7368 ISAM ONT D r a f t Click MaintenanceReboot Device from the left pane in the GPON Home Gateway page. The Reboot Device page displays. Figure 7-51 Reboot Device page Click Reboot to reboot the ONT. 2 END OF STEPS September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 161 Configure a G-2426G-A indoor ONT Maintenance Resetting to factory defaults t f a r D 7.55 Resetting to factory defaults 1 7368 ISAM ONT Click MaintenanceFactory Default from the left pane in the GPON Home Gateway page. The Factory Default page displays. Figure 7-52 Factory Default page Click Factory Default to reset the ONT to its factory default settings. 2 END OF STEPS t f a r D 162 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Maintenance Diagnosing WAN connections 7.56 Diagnosing WAN connections 7368 ISAM ONT D r a f t Click MaintenanceDiagnostics from the left pane in the GPON Home Gateway page. The Diagnostics page displays. Figure 7-53 Diagnostics page Select a WAN connection to diagnose from the list. Enter the IP address or domain name. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 163 1 2 3 Configure a G-2426G-A indoor ONT Maintenance Viewing log files t f a r D Select the test type: ping, traceroute, or both. 7368 ISAM ONT 4 5 6 7 8 9 1 Enter the number of ping attempts to perform (1 - 1000); the default is 4. Enter a ping packet length (64-1024); the default is 64. Enter the maximum number of trace hops (1-255); the default is 30. Click Start Test. The results will be displayed at the bottom of the page. Click Cancel to cancel the test. END OF STEPS 7.57 Viewing log files Click MaintenanceLog from the left pane in the GPON Home Gateway page. The Log page displays. t f a r D 164 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT Maintenance Viewing log files Figure 7-54 Log page 7368 ISAM ONT D r a f t Select a write level from the list to determine which types of events are recorded in the log file:

2 Emergency Alert Critical Error Warning Notice Informational Debug September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 165 Configure a G-2426G-A indoor ONT Maintenance Viewing log files t f a r D 3 7368 ISAM ONT Select a reading level from the list to determine which types of events to display from the log file:

Emergency Alert Critical Error Warning Notice Informational Debug END OF STEPS The log file is displayed at the bottom of the page. t f a r D 166 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t RG Troubleshooting Counters Configure a G-2426G-A indoor ONT RG Troubleshooting Counters Overview 7.58 Overview 7.58.1 Purpose 7.58.2 Contents 7.58 Overview This section describes the RG troubleshooting counters GUI procedures. 7.59 Viewing Residential Gateway (RG) troubleshooting counters 167 167 7.59 Viewing Residential Gateway (RG) troubleshooting counters The Troubleshooting Counters feature enables service providers and end users to monitor the performance of their broadband connection. Tests are run to retrieve upstream and downstream throughput, latency, and DNS response time. The Troubleshooting Counters window also displays upstream and downstream packet loss and Internet status. 1 Click RG TroubleshootingRG Troubleshoot Counters from the left pane in the GPON Home Gateway page. The RG Troubleshoot Counters page displays. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 167 Configure a G-2426G-A indoor ONT RG Troubleshooting Counters Viewing Residential Gateway (RG) troubleshooting counters 7368 ISAM ONT t f a r D 2 Configure the following parameters:

Table 7-42 RG Troubleshooting Counters parameters Field Description WAN Connection List Select a WAN connection from the list. US Throughput DS Throughput This test is used to determine the upstream throughput/speed. Click US Speed Test to specify the time for the upstream test. The default is weekly, performed at idle to a public server. This test is used to determine the downstream throughput/speed. Click DS Speed Test to specify the time for the downstream test. The default is weekly, performed at idle to a public server. US Packet Loss Indicates the number of upstream packages lost. t f a r D 168 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 Configure a G-2426G-A indoor ONT RG Troubleshooting Counters Viewing Residential Gateway (RG) troubleshooting counters Table 7-42 RG Troubleshooting Counters parameters (continued) 7368 ISAM ONT D r a f t Field DS Packet Loss Internet Status Latency DNS Response Time Description Indicates the number of downstream packages lost. Indicates whether the broadband connections is active (UP) or not (DOWN). This test is used to determine the lowest round-trip time in milliseconds by pinging the target server multiple times Click Latency Test to specify the time for the test. The default is weekly, performed at idle to a public server. This test is used to determine the lowest round-trip time in milliseconds by sending a request to the target DNS server. Click DNS Response Test to specify the time for the test. The default is weekly, performed at idle to a public server. Click Refresh to view up-to-date information. 3 END OF STEPS September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 169 Configure a G-2426G-A indoor ONT RG Troubleshooting Counters Viewing Residential Gateway (RG) troubleshooting counters 7368 ISAM ONT t f a r D t f a r D 170 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 ONT configuration file over OMCI Overview 8 ONT configuration file over OMCI 7368 ISAM ONT D r a f t 8.1 Overview 8.1.1 Purpose 8.1.2 Contents 8.1 Overview 8.2 Purpose 8.3 Supported configuration file types 8.4 ONT configuration file over OMCI 8.2 Purpose 171 171 171 174 This procedure describes how to use configuration files over OMCI to configure ONTs. Some advantages include:

flexibility to change the ONT default behavior by downloading configuration file flexibility to update a deployed ONT by downloading updated parameters ability to securely download any configuration file to an ONT ability to avoid using embedded configuration files in ONT software Note: This feature is supported for use with the 7360 ISAM FX and the 7342 ISAM FTTU. 8.3 Supported configuration file types Table 8-1, Supported configuration files (p. 172) describes the configuration file types that are supported from 7368 ISAM ONT R05.02.00 and later. September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 171 ONT configuration file over OMCI Supported configuration file types 7368 ISAM ONT t f a r D Table 8-1 Supported configuration files File Index Description Details PRE ONT pre-configuration file Supported ONTs/DPU All Nokia GPON and 10 GPON ONT. The XML-based PRECONFIG file controls the working mechanics of the ONT for various services. The default behavior of different ONTs may vary based on the factory settings. The pre-configuration file includes the factory default value for the residential gateway. Note: the pre-configuration file does not work with SFU ONTs; therefore, this feature applies only to Residential Gateway ONTs. The pre-configuration file can be used as is, but Nokia provides its customers with the flexibility to customize the pre-configuration file. This pre-configuration file enables operators to change the default behavior by downloading a customized pre-configuration based on customer inputs. This PRE XML file includes a custom OPERID. The Nokia defined index for the PRECONFIG file is: "PRE"

The XML-based CFG file updates the configurable parameters (the PRE settings) in the existing PRE file of a deployed ONT, where required. This configuration file enables operators to change the deployed behavior by downloading customized updates in the CFG file. This file is used only to modify the parameters in the PRE file; it is not used for service provisioning. No OPERID is required, because the update is based on the OPERID used for the PRE file. The Nokia defined index for the PRECONFIG DELTA file is:

"CFG"

The Voice XML file provides an alternate method for securely downloading voice parameters from the OLT, rather than using FTP (OMCIv1/OMCIv2) or HTTPS (TR-069). Downloading this file makes the applicable changes in the voice parameters. This file enables operators to change the voice behavior by downloading the updated voice XML file. Nokia recommends using this procedure, rather than embedded voice XML files. The Nokia defined index for the Voice XML file is: "XML"

CFG ONT configuration delta file All Nokia GPON and 10GPON ONT. XML Voice XML file All Nokia GPON and 10 GPON ONT. t f a r D 172 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 7368 ISAM ONT D r a f t ONT configuration file over OMCI Supported configuration file types Table 8-1 Supported configuration files (continued) File Index Description Details Supported ONTs/DPU GFT G.fast-related configuration file This text-based json script file controls the default behavior of the G.Fast ONT. Nokia G.fast. This file includes the provisioning parameters of the G.fast transports layer; it does not include VLAN or QoS provisioning. While the ONT functions well with the default values; they can optionally be customized. While default values can work in VDSL mode, a download file is required for the device to function as a G.fast ONT. The Nokia defined index for the G.fast file is: "GFT"

8.3.1 Filename conventions Nokia provides the raw configuration files, which must be saved by the operator in a TAR file to be uploaded. TAR file names must be unique. The filenames of the raw configuration files may not adhere to the naming conventions outlined below. In this case, the files must be renamed to adhere to the naming conventions before the operator generates the TAR file. Filenames are not case-sensitive. ABCXXXXVER where ABC is the file index type (PRE, CFG, XML, GFT) XXXX is the operator ID For PRE and CFG, a valid operator ID is required For XML and GFT, any characters may be used VER is the file version (from 001 to 999) Note: you cannot update the configuration using two files with the same name. 8.3.2 Download configuration file The following table provides the supported download options for ONT pre-configuration file and configuration file. Table 8-2 Download configuration files ONT type Legacy method download Zero management download PRE file CFG file PRE file CFG file Broadlight(eg.I240WA-

3FE54869AFGA80) Broadcom(eg.G240WB-

3FE56773BFGA07) September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 173 ONT configuration file over OMCI ONT configuration file over OMCI 7368 ISAM ONT t f a r D Table 8-2 Download configuration files (continued) ONT type Legacy method download Zero management download MTK(eg.G240WF) PRE file CFG file PRE file CFG file 8.4 ONT configuration file over OMCI WARNING Equipment Damage Executing the following procedure will trigger the ONT to reboot, which will impact ongoing services. Use this procedures to configure ONTs using configuration files via legacy method and OMCI. 8.4.1 Configuring an ONT using a configuration file via legacy method Upload the ABCXXXXVER TAR file to the /ONT/ directory in the OLT. A maximum of 250 files can be kept in the OLT file system. 1 2 Using OLT commands, download the TAR file to the ONT. For OLT commands, refer to the 7360 ISAM FX CLI Command Guide for 100_320Gbps FD NT and FX NT, or the 7342 ISAM FTTU Operation and Maintenance Using TL1 and CLI. Please note:

pri-cfgfile-pland/dnload or sec-cfgfile-pland/dnload can be 1 to 14 characters. pri-cfgfile-pland and pri-cfgfile-dnload should be the same name. Examples Note: X can be 1 or 2 unless specified:

a. If pland-cfgfileX= Disabled and dnload-cfgfileX= Disabled , no file will be downloaded to the ONT. b. If pland-cfgfileX=FILENAME1 and dnload-cfgfileX= Disabled , FILENAME1 will be downloaded and FILENAME1 will be made active. An ONT reboot is required. c. If pland-cfgfileX=Disabled and dnload-cfgfileX= FILENAME2 FILENAME2 will be downloaded and FILENAME2 will be made passive. An ONT reboot is not required. d. If pland-cfgfileX=FILENAME3 and dnload-cfgfileX= FILENAME 4, the OLT reports an error because the filenames are not the same. t f a r D 174 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1 ONT configuration file over OMCI ONT configuration file over OMCI 7368 ISAM ONT D r a f t e. Configure equipment interface pland-cfgfile1=XMLXXXXXX1 and dnload-cfgfile1 XMLXXXXXX1 Configure equipment interface pland-cfgfile2=XMLXXXXXX2 and dnload-cfgfile2 XMLXXXXXX2 Although the OLT permits the above two steps without reporting an error, Nokia does not recommend executing them, because the ONT may exhibit unexpected behavior. f. If pland-cfgfileX=Auto and dnload-cfgfileX= Auto The OLT will download the XML file from "sw-ctr-list" (configure equipment ont sw-ctrl) END OF STEPS The ONT will distribute the configuration files to the different services based on the active indication from the OLT and on the Nokia defined index. The ONT automatically reboots to apply the configuration files. After the ONT reboots and reports the active version, the OLT completes the file download procedure. Operators must check the committed file from the OLT to verify whether the corresponding file has been applied. If an error occurs, contact Nokia for support. 8.4.2 Configuring an ONT using a configuration file via OMCI Generate the TAR file to be uploaded to the OLT. Using the raw configuration file(s) provided by Nokia, generate the TAR file as follows:

a. On a Linux platform, rename the raw configuration file to adhere to the naming convention, as described in section 8.3 Supported configuration file types (p. 171). 1 2 3 b. Tar the ABCXXXXVER raw configuration file:

tar -cf ABCXXXXVER.tar ABCXXXXVER Where ABCXXXXVER Is the name of the file created in step i. This creates two files: ABCXXXXVER and ABCXXXXVER.tar. c. Rename ABCXXXXVER to ABCXXXXVER.org d. Remove the .tar extension from ABCXXXXVER.tar file. Upload the ABCXXXXVER TAR file to the /ONT/ directory in the OLT. A maximum of 250 files can be kept in the OLT file system. Using OLT commands, download the TAR file to the ONT. For OLT commands, refer to the 7360 ISAM FX CLI Command Guide for 100_320Gbps FD NT September 2020 Issue 1 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA D r a f t 175 ONT configuration file over OMCI ONT configuration file over OMCI 7368 ISAM ONT t f a r D and FX NT, or the 7342 ISAM FTTU Operation and Maintenance Using TL1 and CLI. Please note:

pri-cfgfile-pland/dnload or sec-cfgfile-pland/dnload can be 1 to 14 characters. pri-cfgfile-pland and pri-cfgfile-dnload should be the same name. Examples Note: X can be 1 or 2 unless specified:

a. If pland-cfgfileX= Disabled and dnload-cfgfileX= Disabled , no file will be downloaded to the ONT. b. If pland-cfgfileX=FILENAME1 and dnload-cfgfileX= Disabled , FILENAME1 will be downloaded and FILENAME1 will be made active. An ONT reboot is required. c. If pland-cfgfileX=Disabled and dnload-cfgfileX= FILENAME2 FILENAME2 will be downloaded and FILENAME2 will be made passive. An ONT reboot is not required. d. If pland-cfgfileX=FILENAME3 and dnload-cfgfileX= FILENAME 4, the OLT reports an error because the filenames are not the same. e. Configure equipment interface pland-cfgfile1=XMLXXXXXX1 and dnload-cfgfile1 XMLXXXXXX1 Configure equipment interface pland-cfgfile2=XMLXXXXXX2 and dnload-cfgfile2 XMLXXXXXX2 Although the OLT permits the above two steps without reporting an error, Nokia does not recommend executing them, because the ONT may exhibit unexpected behavior. f. If pland-cfgfileX=Auto and dnload-cfgfileX= Auto The OLT will download the XML file from "sw-ctr-list" (configure equipment ont sw-ctrl) END OF STEPS The ONT will distribute the configuration files to the different services based on the active indication from the OLT and on the Nokia defined index. The ONT automatically reboots to apply the configuration files. After the ONT reboots and reports the active version, the OLT completes the file download procedure. Operators must check the committed file from the OLT to verify whether the corresponding file has been applied. If an error occurs, contact Nokia for support. t f a r D 176 Nokia Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1

bbb WEVULELY 7 OE RT Lt on st eee recess ceseseessesesese, Pree rere eeesseeeeceseses

+0/-0.2 69.9 NOKIA 12VDC S== 2A ASSEMBLED IN CHINA FE Gri) Fec1o-2ananezszeca OUNGER- Rapoconrat pursuant to Laser Notice No.50,dated lune 26,2007 71 CFR 1040,10 and 1040.11 except for deviations

meee ose TAT TUTTI TH UIT TMT TT ONT P/NX00XXXXXXXXK WU AAU A TT HT 1 VOTH AM 111 TIMI SEZ

+0/-0.2 69.9 NOKIA 12VDC S== 2A ASSEMBLED IN CHINA FE Gri) Fec1o-2ananezszeca OUNGER- Rapoconrat pursuant to Laser Notice No.50,dated lune 26,2007 71 CFR 1040,10 and 1040.11 except for deviations

meee ose TAT TUTTI TH UIT TMT TT ONT P/NX00XXXXXXXXK WU AAU A TT HT 1 VOTH AM 111 TIMI SEZ

Nokia Shanghai Bell Co., Ltd Request for Confidentiality Date: _2020/9/22_ Subject: Confidentiality Request for: _____ FCC ID: 2ADZRG2426GA______ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent*1 Permanent Permanent Permanent Permanent Permanent*

Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual

*Note: ______(Insert Explanation as Necessary)______ ____ Nokia Shanghai Bell Co., Ltd _____ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of _180_ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TCB in the event information regarding the product or the product is made available to the public. TCB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By:

Yong Tu

(Signature/Title2)

(Print name)

Nokia Shanghai Bell Co., Ltd POWER OF ATTORNEY We, the undersigned, hereby authorize TA Technology (Shanghai) Co., Ltd. /Liu mengting on our behalf, to apply to FCC Approval for FCC ID: 2ADZRG2426GA on our equipment. Any and all acts carried out by TA Technology (Shanghai) Co., Ltd.

/Liu mengting on our behalf shall have the same effect as acts of our own. DATE: September 27, 2020 To Whom It May Concern:

Sincerely, Nokia Shanghai Bell Co., Ltd

<SIGNATURE>

(PERSON) Yong Tu

(TITLE) Hardware Manager