FCC ID: 2ADZR4G06A FastMile 4G Receiver

Nokia FastMile 4G Receiver Product Overview FastMile 2.1.06 Nokia FastMile 4G Receiver Product Overview 3TG-00386-ABGA-TCZZA Issue: DRAFT July 2020 Nokia Proprietary and confidential Use pursuant to applicable agreements Nokia FastMile 4G Receiver Product Overview Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners. The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein. 2020 Nokia. Contains proprietary/trade secret information which is the property of Nokia and must not be made available to, or copied or used by anyone outside Nokia without its written authorization. Not to be used or disclosed except in accordance with applicable agreements. 2 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Preface 1 Preface This preface provides general information about the Product Overview for the Nokia FastMile 4G Receiver. 1.1 Summary of document issue changes Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues. Issue 01: first issue of the document for this release of the FastMile 4G Receiver 1.2 Scope 1.3 Audience This document provides an overview of the Nokia FastMile 4G Receiver along with information about safety and troubleshooting the Nokia FastMile 4G Receiver. This document is intended for planners, administrators, operators, and maintenance personnel involved in installing, upgrading, or maintaining the Nokia FastMile 4G Receiver. 1.4 Required knowledge The reader must be familiar with general telecommunications principles. 1.5 Acronyms and initialisms The expansions and optional descriptions of most acronyms and initialisms used in this document appear in the glossary at the back of the document. 1.6 Assistance and ordering phone numbers Nokia provides global technical support through the following URL:

https://customer.nokia.com/support/s/. For ordering information, contact your Nokia sales representative. Issue: DRAFT 3TG-00386-ABGA-TCZZA 3 Preface Nokia FastMile 4G Receiver Product Overview 1.7 Nokia quality processes Nokias FastMile 4G Receiver quality practices are in compliance with TL 9000 requirements.These requirements are documented in the Fixed Networks Quality Manual 3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met. The customer or its representatives may be allowed to perform on-site quality surveillance audits, as agreed upon during contract negotiations. 1.8 Safety information For safety information, see the appropriate safety guideline chapters. 1.9 Documents Documents are available at the Nokia Documentation Center. Procedure 1 To access a document on the Nokia Documentation Center Individual PDFs of customer documents are accessible through the Nokia Documentation Center. 1 Go to https://documentation.nokia.com Log in as required. Enter FastMile 4G Receiver in the Product box. 2 3 4 Click on the PDF icon to access a document. Select the search criteria as needed (Release, Content Type, Sort by, etc.) and Click on Search. 4 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Preface 1.10 Special information The following are examples of how special information is presented in this document. Danger Danger indicates that the described activity or situation may result in serious personal injury or death; for example, high voltage or electric shock hazards. Warning Warning indicates that the described activity or situation may, or will, cause equipment damage or serious performance problems. Caution Caution indicates that the described activity or situation may, or will, cause service interruption. Note A note provides information that is, or may be, of special interest. 1.10.1 Steps with options or substeps When there are options in a step, they are identified by letters. When there are required substeps in a step, they are identified by roman numerals. Procedure 2 Example of options in a step At step 1, you must choose option a or b. 1 This step offers two options. You must choose one of the following:

a b This is one option. This is another option. 2 You must perform this step. Issue: DRAFT 3TG-00386-ABGA-TCZZA 5 Preface Nokia FastMile 4G Receiver Product Overview Procedure 3 Example of required substeps in a step At step 1, you must perform a series of substeps within the step. 1 This step has a series of substeps that you must perform to complete the step. You must perform the following substeps:

i ii This is the first substep. This is the second substep. iii This is the third substep. 2 You must perform this step. 1.11 Multiple PDF document search You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel. The results are grouped by PDF file, and you can expand the entry for each file. Note The PDF files in which you search must be in the same folder. Procedure 4 To search multiple PDF files for a common term Open Adobe Acrobat Reader. Choose EditSearch from the Acrobat Reader main menu. The Search PDF panel appears. 1 2 3 4 5 6 Enter the search criteria. Click on the All PDF Documents In radio button. Select the folder in which to search using the drop-down menu. Click on the Search button. 6 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Preface Acrobat Reader displays the search results. You can expand the entries for each document by clicking on the + symbol. Issue: DRAFT 3TG-00386-ABGA-TCZZA 7 Preface Nokia FastMile 4G Receiver Product Overview 8 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Table of contents 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.10.1 1.11 2 2.1 2.1.1 2.1.2 2.1.2.1 2.1.2.2 2.2 2.3 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 2.3.6 2.3.7 2.4 3 3.1 3.1.1 3.1.2 3.2 3.2.1 3.2.2 3.2.3 3.2.4 3.3 3.3.1 3.3.2 3.3.3 3.4 Preface.............................................................................................3 Summary of document issue changes ........................................................3 Scope ..........................................................................................................3 Audience......................................................................................................3 Required knowledge....................................................................................3 Acronyms and initialisms .............................................................................3 Assistance and ordering phone numbers ....................................................3 Nokia quality processes...............................................................................4 Safety information........................................................................................4 Documents ..................................................................................................4 Special information ......................................................................................5 Steps with options or substeps....................................................................5 Multiple PDF document search ...................................................................6 ETSI environmental and CRoHS guidelines...............................19 Environmental labels .................................................................................19 Overview....................................................................................................19 Environmental related labels .....................................................................19 Products below Maximum Concentration Value (MCV) label....................19 Products containing hazardous substances above Maximum Concentration Value (MCV) label ..............................................................20 Hazardous Substances Table (HST).........................................................21 Other environmental requirements ............................................................21 Environmental requirements......................................................................22 Storage ......................................................................................................22 Transportation ...........................................................................................22 Stationary use............................................................................................22 Thermal limitations ....................................................................................22 Material content compliance......................................................................23 End-of-life collection and treatment ...........................................................23 Additional information ................................................................................24 ETSI safety guidelines..................................................................25 Safety instructions .....................................................................................25 Safety instruction boxes ............................................................................25 Safety-related labels..................................................................................26 Safety standards compliance ....................................................................26 EMC compliance .......................................................................................27 Equipment safety standard compliance.....................................................27 Environmental standard compliance .........................................................27 Laser product standard compliance ..........................................................27 Electrical safety guidelines ........................................................................28 Power supplies ..........................................................................................28 Cabling ......................................................................................................28 Protective earth .........................................................................................28 ESD safety guidelines ...............................................................................29 Issue: DRAFT 3TG-00386-ABGA-TCZZA 9 Nokia FastMile 4G Receiver Product Overview Environmental requirements......................................................................29 Additional information ................................................................................29 ANSI safety guidelines .................................................................31 Safety instructions .....................................................................................31 Safety instruction boxes in customer documentation ................................31 Safety-related labels..................................................................................32 Safety standards compliance ....................................................................33 EMC, EMI, and ESD compliance...............................................................34 Equipment safety standard compliance.....................................................34 Electrical safety guidelines ........................................................................35 Power supplies ..........................................................................................35 Cabling ......................................................................................................35 Protective earth .........................................................................................35 ESD safety guidelines ...............................................................................36 Environmental requirements......................................................................36 Additional information ................................................................................36 Product overview..........................................................................37 Overview of the Nokia FastMile 4G Receiver............................................37 End-to-end example .................................................................................39 Installing the Nokia FastMile 4G Receiver.................................................40 Functional overview .....................................................................41 Overview....................................................................................................41 Nokia Wireless app....................................................................................41 Web UI.......................................................................................................42 Remote management ................................................................................43 LTE characteristics ....................................................................................43 Data forwarding ........................................................................................44 Ethernet characteristics .............................................................................44 Power supply characteristics .....................................................................45 Remote management protocols ................................................................45 Model overview .............................................................................49 Models of the Nokia FastMile 4G Receiver ...............................................49 Label information .......................................................................................51 Physical interfaces .......................................................................53 Physical interfaces of the Compact mono-band and ABA models ............53 Physical interfaces of the Compact multi-band models.............................54 SIM cards.......................................................................................57 SIM card information for the Compact mono-band and ABA models........57 SIM card information for the Compact multi-band models ........................58 LEDs...............................................................................................59 Status LED ................................................................................................59 Signal strength LEDs ................................................................................61 Power information ........................................................................63 Power information for the Nokia FastMile 4G Receiver ............................63 Available PoE injectors..............................................................................63 3.5 3.6 4 4.1 4.1.1 4.1.2 4.2 4.2.1 4.2.2 4.3 4.3.1 4.3.2 4.3.3 4.4 4.5 4.6 5 5.1 5.2 5.3 6 6.1 6.1.1 6.1.2 6.1.3 6.2 6.3 6.4 6.5 6.6 7 7.1 7.1.1 8 8.1 8.2 9 9.1 9.2 10 10.1 10.2 11 11.1 11.2 10 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview 12 12.1 12.2 12.3 12.4 13 13.1 13.2 13.3 14 14.1 14.2 14.3 14.4 14.5 15 15.1 15.2 16 16.1 17 17.1 18 18.1 18.2 18.3 19 Performance information .............................................................67 Performance overview...............................................................................67 Throughput information .............................................................................67 Carrier aggregation information.................................................................68 Power consumption information ................................................................82 Management using the Nokia Wireless app ...............................83 Using the Nokia Wireless app to manage the Nokia FastMile 4G Receiver ...................................................................................................83 Using the Nokia Wireless app to manage a unit managed by the Nokia Altiplano FastMile Controller ...........................................................86 Using the Nokia Wireless app to manage a unit managed by an ACS .........................................................................................................104 Management using the Web UI..................................................125 Using the Web UI to manage the Nokia FastMile 4G Receiver...............125 Using the Web UI status screen ..............................................................125 Using the Web UI network screen ...........................................................131 Using the Web UI CBRS screen..............................................................142 Using the Web UI system screen ............................................................143 Standards certification...............................................................151 Standards certification for Compact mono-band and ABA models .........151 Standards certification for the Compact multi-band models ....................152 Appendix A: Specifications .......................................................153 Specifications ..........................................................................................153 Appendix B: RF exposure ..........................................................155 RF exposure ............................................................................................155 Appendix C: FCC statements and label instructions ..............157 FCC compliance statement .....................................................................157 FCC radiation exposure statement..........................................................158 FCC label instructions .............................................................................158 Glossary ......................................................................................159 Issue: DRAFT 3TG-00386-ABGA-TCZZA 11 Nokia FastMile 4G Receiver Product Overview 12 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview List of figures 2 Figure 1 Figure 2 Figure 3 4 Figure 4 Figure 5 5 Figure 6 Figure 7 Figure 8 6 Figure 9 Figure 10 8 Figure 11 Figure 12 Figure 13 9 Figure 14 Figure 15 10 Figure 16 Figure 17 Figure 18 Figure 19 13 Figure 20 Figure 21 Figure 22 Figure 23 ETSI environmental and CRoHS guidelines...............................19 Products below MCV value label...............................................................20 Products above MCV value label ..............................................................21 Recycling/take back/disposal of product symbol .......................................23 ANSI safety guidelines .................................................................31 Sample safety label for FCC......................................................................33 Sample safety label for ETL ......................................................................33 Product overview..........................................................................37 Application example of the Nokia FastMile 4G Receiver...........................38 Examples of model types of the Nokia FastMile 4G Receiver...................39 End-to-end example featuring the Nokia FastMile 4G Receiver with a residential gateway and PoE injector .....................................................40 Functional overview .....................................................................41 Remote management of the Nokia FastMile 4G Receiver through the Nokia Altiplano FastMile Controller ....................................................46 Remote management of the Nokia FastMile 4G Receiver through an ACS ......................................................................................................47 Physical interfaces .......................................................................53 Location of physical interfaces on the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver ...............................................54 Location of the ground point for the Compact multi-band models of the Nokia FastMile 4G Receiver................................................................56 Location of physical interfaces on the underside of the Compact multi-band models of the Nokia FastMile 4G Receiver .............................56 SIM cards.......................................................................................57 Detailed view of SIM card slot on the Compact mono-band and ABA models...............................................................................................57 Detailed view of SIM card slot on the Compact multi-band models ..........58 LEDs...............................................................................................59 Location of the status LED on the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver ...............................................59 Location of the status LED on the Compact multi-band models of the Nokia FastMile 4G Receiver................................................................59 Location of the signal strength LEDs.........................................................61 Location of the measurement button .........................................................61 Management using the Nokia Wireless app ...............................83 Before we begin screen.............................................................................84 Terms of Service screen............................................................................85 Introductory screen for unit managed by the Nokia Altiplano FastMile Controller through NETCONF.....................................................87 Screen with prompt to scan the QR code for unit managed by the Nokia Altiplano FastMile Controller through NETCONF............................88 Issue: DRAFT 3TG-00386-ABGA-TCZZA 13 Nokia FastMile 4G Receiver Product Overview QR code screen for unit managed by the Nokia Altiplano FastMile Controller through NETCONF ...................................................................89 Screen showing the Already Installed option for unit managed by the Nokia Altiplano FastMile Controller through NETCONF......................90 Screen for connecting to the Nokia FastMile 4G Receiver........................91 Screen for enabling the VPN profile ..........................................................92 Prompt for accepting the connection request ............................................93 Screen to log in to a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller ...........................................................94 System state screen example for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller.................................96 System state screen with Beam Angle information for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller . 97 Screen that has the Upload CA certificates option for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller . 98 Screen that lists the CA certificates for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller .................99 Screen indicating that uploading of the CA certificates was successful for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller ..................................................................................100 Screen showing the Reboot Device option for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller..........101 Screen showing the reboot message for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller ...............102 Screen showing the Perform Factory Reset option for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller . 103 Screen showing the factory reset message for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller ...............104 Introductory screen for unit managed by an ACS through TR-069 .........106 Screen with prompt to scan the QR code for unit managed by an ACS through TR-069 ...............................................................................107 QR code screen for unit managed by an ACS through TR-069 ..............108 Screen showing the Already Installed option for unit managed by an ACS through TR-069 ..........................................................................109 Screen for connecting to the Nokia FastMile 4G Receiver......................110 Screen for enabling the VPN profile ........................................................111 Prompt for accepting the connection request ..........................................112 Screen to log in to a Nokia FastMile 4G Receiver managed by an ACS through TR-069 ...............................................................................113 System state screen example for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 .....................................................115 System state screen with Beam Angle information for a Nokia FastMile 4G Receiver managed by an ACS through TR-069..................116 Screen that has the Upload CA certificates option for a Nokia FastMile 4G Receiver managed by an ACS through TR-069..................117 Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 Figure 29 Figure 30 Figure 31 Figure 32 Figure 33 Figure 34 Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 14 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 Figure 55 14 Figure 56 Figure 57 Figure 58 Figure 59 Figure 60 Figure 61 Figure 62 Figure 63 Figure 64 Figure 65 Figure 66 Figure 67 Figure 68 Figure 69 Figure 70 Figure 71 Figure 72 Figure 73 Figure 74 Figure 75 Figure 76 Figure 77 Figure 78 Figure 79 Figure 80 Figure 81 Upload CA Certificates screen for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 .....................................................118 List of CA certificates displayed on the Upload CA Certificates screen for a Nokia FastMile 4G Receiver managed by an ACS through TR-069.....................................................................................................119 Screen showing that upload of CA certificates was successful for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 .......121 Screen showing the Reboot Device option for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 ................................122 Screen showing the Perform Factory Reset option for a Nokia FastMile 4G Receiver managed by ACS through TR-069.......................123 Screen showing the factory reset message for a Nokia FastMile 4G Receiver managed by ACS through TR-069 ...........................................124 Management using the Web UI..................................................125 Example of the top part of the Status screen when the FastMile 4G Receiver is not connected to a cell..........................................................127 Example of the lower part of the Status screen without available cells when the FastMile 4G Receiver is not connected to a cell..............127 Example of the lower part of the Status screen with available cells when the FastMile 4G Receiver is not connected to a cell......................128 Example of the top part of the Status screen when the FastMile 4G Receiver is connected to a cell................................................................128 Example of a lower part of the Status screen when the FastMile 4G Receiver is connected to a cell................................................................129 Example of the Trigger Measurement pop up window ............................129 Example of ongoing Trigger Measurement .............................................130 Example of Trigger Measurement completed and FastMile 4G Receiver is detached ...............................................................................130 Example of Trigger Measurement completed and FastMile 4G Receiver is reattached.............................................................................131 Example of the lowest part of the Status screen when the FastMile 4G Receiver is connected to a cell ..........................................................131 Example of the Login screen ...................................................................133 Example of the Network screen...............................................................134 Example of scroll down for the Network screen ......................................134 Example of the Add Access Point window ..............................................135 Example of the Delete Access Point window ..........................................136 Example of the Edit Location window......................................................137 Example of the Edit Controller window....................................................138 Example of the Edit Connection Request window...................................139 Example of the Edit DHCP window .........................................................140 Example of the Certificates information window......................................141 Example of the Add Cell window .............................................................141 Example of the Delete Cell window .........................................................142 Example of the Web UI CBRS screen ....................................................143 Example of the System screen................................................................144 Example of the Restart Device confirmation window ..............................145 Example of the Restore Device confirmation window .............................146 Issue: DRAFT 3TG-00386-ABGA-TCZZA 15 Nokia FastMile 4G Receiver Product Overview Figure 82 Figure 83 Figure 84 Example of the screen that displays while firmware is being uploaded..................................................................................................147 Example of the screen that displays while firmware is being upgraded .................................................................................................148 Example of the screen that displays while the system is being rebooted ..................................................................................................149 16 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview List of tables 3 Table 1 4 Table 2 6 Table 3 Table 4 7 Table 5 Table 6 8 Table 7 Table 8 10 Table 9 Table 10 Table 11 11 Table 12 Table 13 Table 14 12 Table 15 Table 16 Table 17 Table 18 Table 19 Table 20 Table 21 ETSI safety guidelines..................................................................25 Safety labels ..............................................................................................26 ANSI safety guidelines .................................................................31 Safety labels ..............................................................................................32 Functional overview .....................................................................41 E-UTRA bands supported by the Nokia FastMile 4G Receiver.................43 Data forwarding methods supported by the Nokia FastMile 4G Receiver ....................................................................................................44 Model overview .............................................................................49 Models of the Nokia FastMile 4G Receiver ...............................................49 Label information for the Nokia FastMile 4G Receiver ..............................51 Physical interfaces .......................................................................53 Physical interfaces of the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver................................................................53 Physical interfaces of the Compact multi-band models of the Nokia FastMile 4G Receiver ................................................................................54 LEDs...............................................................................................59 Status LED behavior for Nokia FastMile 4G Receiver managed from the Nokia Altiplano FastMile Controller .............................................60 Status LED behavior for Nokia FastMile 4G Receiver managed from an ACS ......................................................................................................60 Signal strength LED threshold values .......................................................62 Power information ........................................................................63 Available PoE injectors for Model 4G05-B ................................................64 Available PoE injectors for Model 4G17-A ................................................64 Available PoE injectors for models other than Model 4G05-B and Model 4G17-A ...........................................................................................65 Performance information .............................................................67 LTE throughput information .......................................................................67 Carrier aggregation support for Model 4G01-A and Model 4G01-B

(2*2 MIMO downlink with SISO uplink)......................................................69 Carrier aggregation support for Model 4G02-A (2*2 MIMO downlink with SISO uplink) .......................................................................................71 Carrier aggregation support for Model 4G03-A (2*2 MIMO downlink with SISO uplink) .......................................................................................71 Carrier aggregation support for Model 4G04-A (2*2 MIMO downlink with SISO uplink) .......................................................................................73 Carrier aggregation support for Model 4G05-A and Model 4G05-B

(2*2 MIMO downlink) .................................................................................73 Carrier aggregation support for Model 4G06-A (2*2 MIMO downlink) ...................................................................................................77 Issue: DRAFT 3TG-00386-ABGA-TCZZA 17 Nokia FastMile 4G Receiver Product Overview Table 22 Table 23 15 Table 24 Table 25 16 Table 26 17 Table 27 18 Table 28 Carrier aggregation support for Model 4G17-A (2*2 MIMO downlink with SISO uplink) .......................................................................................81 Power consumption information for all models..........................................82 Standards certification...............................................................151 Standards certifications for the Nokia FastMile 4G Receiver Compact mono-band and ABA models ...................................................151 Standards certifications for the Nokia FastMile 4G Receiver Compact multi-band models....................................................................152 Appendix A: Specifications .......................................................153 Specifications for the Nokia FastMile 4G Receiver .................................153 Appendix B: RF exposure ..........................................................155 RF exposure distances............................................................................155 Appendix C: FCC statements and label instructions ..............157 FCC ID for Nokia FastMile 4G Receiver..................................................157 18 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview ETSI environmental and CRoHS guidelines 2 ETSI environmental and CRoHS guidelines This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of Nokia FastMile 4G Receiver equipment. This chapter also includes environmental operation parameters of general interest. 2.1 Environmental labels This section describes the environmental instructions that are provided with the customer documentation, equipment, and location where the equipment resides. 2.1.1 Overview CRoHS is applicable to Electronic Information Products (EIP) manufactured or sold and imported in the territory of the mainland of the Peoples Republic of China. EIP refers to products and their accessories manufactured by using electronic information technology, including electronic communications products and such subcomponents as batteries and cables. 2.1.2 Environmental related labels Environmental labels are located on appropriate equipment. The following are sample labels. 2.1.2.1 Products below Maximum Concentration Value

(MCV) label Figure 1 shows the label that indicates a product is below the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). Products with this label are recyclable. The label may be found in this documentation or on the product. Issue: DRAFT 3TG-00386-ABGA-TCZZA 19 ETSI environmental and CRoHS guidelines Nokia FastMile 4G Receiver Product Overview Figure 1 Products below MCV value label 18986 2.1.2.2 Products containing hazardous substances above Maximum Concentration Value (MCV) label Figure 2 shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). The number contained inside the label indicates the Environment-Friendly User Period (EFUP) value. The label may be found in this documentation or on the product. 20 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview ETSI environmental and CRoHS guidelines Figure 2 Products above MCV value label 18985 Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories. These values are based on manufacturers' extensive practical experience of the design, manufacturing, maintenance, usage conditions, operating environments, and physical condition of infrastructure and handsets after years of service. The values reflect minimum values and refer to products operated according to the intended use conditions. See Hazardous Substances Table (HST) for more information. 2.2 Hazardous Substances Table (HST) This section describes the compliance of the Nokia FastMile 4G Receiver equipment to the CRoHS standard when the product and subassemblies contain hazardous substances beyond the MCV value. This information is found in this user documentation where part numbers for the product and subassemblies are listed. It may be referenced in other documentation that describes the Nokia FastMile 4G Receiver equipment. In accordance with the Peoples Republic of China Electronic Industry Standard Marking for the Control of Pollution Caused by Electronic Information Products

(SJ/T11364-2006), customers may access the Nokia Hazardous Substance Table, in Chinese, by contacting their Nokia representative. 2.3 Other environmental requirements Observe the following environmental requirements when handling Nokia FastMile 4G Receiver equipment. Issue: DRAFT 3TG-00386-ABGA-TCZZA 21 ETSI environmental and CRoHS guidelines Nokia FastMile 4G Receiver Product Overview 2.3.1 Environmental requirements See chapter 16 in this document for more information about temperature ranges for the Nokia FastMile 4G Receiver equipment and other Nokia FastMile 4G Receiver specifications. 2.3.2 Storage According to ETS 300-019-1-1 - Class 1.1, storage of Nokia FastMile 4G Receiver equipment must be in Class 1.1, weather-protected, temperature-controlled locations. According to EN 300-019-1-2 - Class 2.3, transportation of Nokia FastMile 4G Receiver equipment must be in packed, public transportation. 2.3.3 Transportation 2.3.4 Stationary use According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of Nokia FastMile 4G Receiver equipment must be in a temperature-controlled location with no condensation allowed. 2.3.5 Thermal limitations The thermal limitations for the Nokia FastMile 4G Receiver equipment are:

operating temperature (ambient):

Compact mono-band and ABA models: 30C to 65C (22F to 149F) Compact multi-band models: 30C to 55C (22F to 131F); Model 4G05-B: 40C to 55C (40F to 131F) Humidity: 5% to 95% non condensing 22 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview ETSI environmental and CRoHS guidelines 2.3.6 Material content compliance European Union (EU) Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment. This Directive applies to electrical and electronic products placed on the EU market after 1 July 2006, with various exemptions, including an exemption for lead solder in network infrastructure equipment. Nokia products shipped to the EU after 1 July 2006 comply with the EU RoHS Directive. Nokia has implemented a material/substance content management process. The process is described in: Nokia process for ensuring RoHS Compliance

(1AA002660031ASZZA). This ensures compliance with the European Union Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS2). With the process equipment is assessed in accordance with the Harmonised Standard EN50581:2012 (CENELEC) on Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances. 2.3.7 End-of-life collection and treatment Electronic products bearing or referencing the symbol shown in Figure 3, when put on the market within the European Union (EU), shall be collected and treated at the end of their useful life, in compliance with applicable EU and local legislation. They shall not be disposed of as part of unsorted municipal waste. Due to materials that may be contained in the product, such as heavy metals or batteries, the environment and human health may be negatively impacted as a result of inappropriate disposal. Figure 3 Recycling/take back/disposal of product symbol At the end of its life, Nokia FastMile 4G Receiver equipment is subject to the applicable local legislations that implement the European Directive 2012/19EU on waste electrical and electronic equipment (WEEE). There can be different requirements for collection and treatment in different member states of the European Union. Issue: DRAFT 3TG-00386-ABGA-TCZZA 23 ETSI environmental and CRoHS guidelines Nokia FastMile 4G Receiver Product Overview In compliance with legal requirements and contractual agreements, where applicable, Nokia will offer to provide for the collection and treatment of Nokia products bearing the logo shown in Figure 3 at the end of their useful life, or products displaced by Nokia equipment offers. For information regarding take-back of equipment by Nokia, or for more information regarding the requirements for recycling/disposal of product, contact your Nokia account manager or Nokia take back support at sustainability.global@nokia.com. 2.4 Additional information See chapter 17 for RF exposure information. 24 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview ETSI safety guidelines 3 ETSI safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of Nokia FastMile 4G Receiver equipment in the ETSI market. 3.1 Safety instructions This section describes the safety instructions that are provided in the customer documentation and on the Nokia FastMile 4G Receiver equipment. 3.1.1 Safety instruction boxes The safety instruction boxes are provided in the Nokia FastMile 4G Receiver customer documentation. Observe the instructions to meet safety requirements. The following is an example of the Danger box. Danger Possibility of personal injury. The Danger box indicates that the described activity or situation may pose a threat to personal safety. It calls attention to a situation or procedure which, if not correctly performed or adhered to, may result in death or serious physical harm. Do not proceed beyond a Danger box until the indicated conditions are fully understood and met. The following is an example of the Warning box. Warning 1 Possibility of equipment damage. Warning 2 Possibility of data loss. The Warning box indicates that the described activity or situation may, or will, cause equipment damage, loss of data, or serious performance problems. It identifies a possible equipment-damaging situation or provides essential information to avoid the degradation of system operations or data. Do not proceed beyond a warning until the indicated conditions are fully understood and met. Issue: DRAFT 3TG-00386-ABGA-TCZZA 25 ETSI safety guidelines Nokia FastMile 4G Receiver Product Overview The following is an example of the Caution box. Caution 1 Possibility of service interruption. Caution 2 Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box. Note Information of special interest. The Note box provides information that assists the personnel working with Nokia FastMile 4G Receiver equipment. It does not provide safety-related instructions. 3.1.2 Safety-related labels The Nokia FastMile 4G Receiver equipment is labeled with the specific safety instructions and compliance information that is related to a product, or product variant or model, of the equipment. Observe the instructions on the safety labels. Table 1 provides sample safety labels on Nokia FastMile 4G Receiver equipment. Table 1 Safety labels Description ESD warning Label text Caution: This assembly contains an electrostatic sensitive device. 3.2 Safety standards compliance This section describes Nokia FastMile 4G Receiver equipment compliance with the European safety standards. 26 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview ETSI safety guidelines 3.2.1 EMC compliance The Nokia FastMile 4G Receiver equipment complies with the following EMC requirements:

Electromagnetic Compatibility (EMC) standard for radio equipment and services;

Part 52: Specific conditions for Cellular Communication Mobile and portable (UE) radio and ancillary equipment; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU Electromagnetic Compatibility (EMC) standard for radio equipment and services;

Part 1: Common technical requirements; Harmonized Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of article 6 of Directive 2014/30/EU EN 301489-1 Electromagnetic Compatibility (EMC) standard for radio equipment and services;

Part 17: Specific conditions for Broadband Data Transmission Systems;

Harmonized Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU EN 301489-17 3.2.2 Equipment safety standard compliance The Nokia FastMile 4G Receiver equipment complies with the requirements of the following:

EN 60950-1, Safety of Information Technology Equipment for use in a restricted location (per R-269) IEC 60950-22, EN 60950-22: Information Technology Equipment- Safety - Part 22 Equipment to be installed Outdoors IEC 62368 Audio/video, information and communication technology equipment-

Part 1: Safety requirements IEC 60529 Degrees of protection provided by enclosures (IP Code) 3.2.3 Environmental standard compliance The Nokia FastMile 4G Receiver equipment complies with the EN 300 019 European environmental standards. 3.2.4 Laser product standard compliance The Nokia FastMile 4G Receiver equipment is not a laser product. Issue: DRAFT 3TG-00386-ABGA-TCZZA 27 ETSI safety guidelines Nokia FastMile 4G Receiver Product Overview 3.3 Electrical safety guidelines This section provides the electrical safety guidelines for the Nokia FastMile 4G Receiver equipment. Note 1 The Nokia FastMile 4G Receiver equipment complies with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards. Note 2 The Nokia FastMile 4G Receiver equipment complies with BS EN 61140. 3.3.1 Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. 3.3.2 Cabling The following are the guidelines regarding cables used for the Nokia FastMile 4G Receiver equipment:

All cables must be approved by the relevant national electrical code. Cables for outdoor connection to the Nokia FastMile 4G Receiver equipment must The Nokia FastMile 4G Receiver equipment must be used with the cabling be suitable for outdoor use. supplied with the equipment. 3.3.3 Protective earth Earthing and bonding of the Nokia FastMile 4G Receiver equipment must comply with the requirements of local electrical codes. 28 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview ETSI safety guidelines 3.4 ESD safety guidelines The Nokia FastMile 4G Receiver equipment is sensitive to ESD if opened. Operations personnel must observe the following ESD instructions when they handle the Nokia FastMile 4G Receiver equipment. Caution This equipment is ESD sensitive if opened. Proper ESD protections should be used if you open the Nokia FastMile 4G Receiver. Service personnel are not required to wear wrist straps when performing normal installation or maintenance activities. 3.5 Environmental requirements See chapter 16 in this document for information about temperature ranges for the Nokia FastMile 4G Receiver equipment and other Nokia FastMile 4G Receiver specifications. During operation in the supported temperature range, condensation inside the Nokia FastMile 4G Receiver equipment caused by humidity is not an issue because the Nokia FastMile 4G Receiver is a sealed unit. 3.6 Additional information See chapter 17 for RF exposure information. Issue: DRAFT 3TG-00386-ABGA-TCZZA 29 ETSI safety guidelines Nokia FastMile 4G Receiver Product Overview 30 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview ANSI safety guidelines 4 ANSI safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the Nokia FastMile 4G Receiver equipment in the North American or ANSI market. 4.1 Safety instructions This section describes the safety instructions that are provided in the customer documentation and on the Nokia FastMile 4G Receiver equipment. 4.1.1 Safety instruction boxes in customer documentation The safety instruction boxes are provided in the Nokia FastMile 4G Receiver customer documentation. Observe the instructions to meet safety requirements. The following is an example of the Danger box. Danger Possibility of personal injury. The Danger box indicates that the described activity or situation may pose a threat to personal safety. It calls attention to a situation or procedure which, if not correctly performed or adhered to, may result in death or serious physical harm. Do not proceed beyond a Danger box until the indicated conditions are fully understood and met. The following is an example of the Warning box. Warning 1 Possibility of equipment damage. Warning 2 Possibility of data loss. The Warning box indicates that the described activity or situation may, or will, cause equipment damage, loss of data, or serious performance problems. It identifies a possible equipment-damaging situation or provides essential information to avoid the degradation of system operations or data. Do not proceed beyond a warning until the indicated conditions are fully understood and met. Issue: DRAFT 3TG-00386-ABGA-TCZZA 31 ANSI safety guidelines Nokia FastMile 4G Receiver Product Overview The following is an example of the Caution box. Caution 1 Possibility of service interruption. Caution 2 Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box. Note Information of special interest. The Note box provides information that assists the personnel working with Nokia FastMile 4G Receiver equipment. It does not provide safety-related instructions. 4.1.2 Safety-related labels The Nokia FastMile 4G Receiver equipment is labeled with specific safety compliance information and instructions that are related to a product, or product model, of the equipment. Observe the instructions on the safety labels. Table 2 provides examples of the text in the various Nokia FastMile 4G Receiver equipment safety labels. Table 2 Safety labels Description UL compliance Label text ETL/cETL UL50E compliance Type 3 ESD warning Caution: This assembly contains electrostatic sensitive device. FCC standards compliance Tested to comply with FCC standards for home or office use. Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CE marking There are various CE symbols for CE compliance. 32 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview ANSI safety guidelines Figure 4 shows a sample safety label for FCC and Figure 5 shows a sample safety label for ETL. Figure 4 Sample safety label for FCC Tested to Comply with FCC Standards FOR HOME OR OFFICE USE c COMMUNICATION SERVICE EQUIPMENT US LISTED 27FY Type 3R Enclosure - Rainproof This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la class A est conforme a la norme NMB-003 du Canada This Assembly Contains Electrostatic Sensitive Devices CAUTION 18533 27799 Figure 5 Sample safety label for ETL 5011710 4.2 Safety standards compliance This section describes the Nokia FastMile 4G Receiver equipment compliance with North American safety standards. Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Issue: DRAFT 3TG-00386-ABGA-TCZZA 33 ANSI safety guidelines Nokia FastMile 4G Receiver Product Overview 4.2.1 EMC, EMI, and ESD compliance The Nokia FastMile 4G Receiver equipment complies with the following EMC, EMI, and ESD requirements:

Federal Communications Commission PART 15-RADIO FREQUENCY DEVICES Subpart C-INTENTIONAL RADIATORS Title 47 CFR Part 15. Part 15.247, Part 15.255 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is needed. Consult the dealer or an experienced radio/TV technician for help. 4.2.2 Equipment safety standard compliance The Nokia FastMile 4G Receiver equipment complies with the requirements of:

UL 62368-1 Audio/Video, Information And Communication Technology Equipment - Part 1: Safety Requirements CSA C22.2#62368-1 Audio/Video, Information And Communication Technology Equipment - Part 1: Safety Requirements UL 60950-22 Information Technology Equipment - Safety - Part 22: Equipment to be Installed Outdoors 34 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview ANSI safety guidelines 4.3 Electrical safety guidelines This section provides the electrical safety guidelines for the Nokia FastMile 4G Receiver equipment. Note The Nokia FastMile 4G Receiver equipment complies with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards. 4.3.1 Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. 4.3.2 Cabling The following are the guidelines regarding cables used for the Nokia FastMile 4G Receiver equipment:

All cables must be approved by the relevant national electrical code. Cables for outdoor connection to the Nokia FastMile 4G Receiver equipment must be suitable for outdoor use. If cabling is supplied with the Nokia FastMile 4G Receiver, the supplied cabling must be used with the equipment. 4.3.3 Protective earth Earthing and bonding of the Nokia FastMile 4G Receiver equipment must comply with the requirements of NEC article 250 or local electrical codes. Issue: DRAFT 3TG-00386-ABGA-TCZZA 35 ANSI safety guidelines Nokia FastMile 4G Receiver Product Overview 4.4 ESD safety guidelines The Nokia FastMile 4G Receiver equipment is sensitive to ESD if opened. Operations personnel must observe the following ESD instructions when they handle the Nokia FastMile 4G Receiver equipment. Caution This equipment is ESD sensitive if opened. Proper ESD protections should be used if you open the Nokia FastMile 4G Receiver. Service personnel are not required to wear wrist straps when performing normal installation or maintenance activities. 4.5 Environmental requirements See chapter 16 in this document for information about temperature ranges for the Nokia FastMile 4G Receiver equipment and other Nokia FastMile 4G Receiver specifications. During operation in the supported temperature range, condensation inside the Nokia FastMile 4G Receiver equipment caused by humidity is not an issue because the Nokia FastMile 4G Receiver is a sealed unit. 4.6 Additional information See chapter 17 for RF exposure information. See chapter 18 for additional FCC compliance information. 36 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Product overview 5 Product overview 5.1 Overview of the Nokia FastMile 4G Receiver 5.2 End-to-end example 5.3 Installing the Nokia FastMile 4G Receiver 5.1 Overview of the Nokia FastMile 4G Receiver The Nokia FastMile 4G Receiver is an outdoor device used in the Nokia FastMile 4G solution. The Nokia FastMile 4G solution uses 3GPP based LTE radio technology to provide indoor and outdoor broadband connectivity with guaranteed high bitrates in larger service areas in a more cost-efficient manner than is possible with other existing solutions.The Nokia FastMile 4G solution can overcome network performance challenges faced by today's mobile networks by optimizing all of the following:

intra site interference due to neighbor sectors in same LTE base station inter site interference due to neighbor base stations link performance due to wall penetration loss and several miles path loss The Nokia FastMile 4G Receiver provides high-performing, outdoor wireless broadband access over LTE to meet residential users total home connectivity needs for urban, suburban, rural, and deep rural spots. The Nokia FastMile 4G Receiver supports LTE connectivity to an LTE base station in the network, and provides 1 Gbps Ethernet connectivity through an Ethernet cable connected to a residential gateway such as the following in the home:

Nokia 7368 ISAM CPE A-020W-A Nokia 7368 ISAM CPE A-240Z-A The Nokia FastMile 4G Receiver can be installed on the side of a house or on a pole close to the house. A pole mount kit that includes a pole adapter can be ordered from Nokia. Figure 6 shows an application example where the Nokia FastMile 4G Receiver is mounted on the side of a house. Issue: DRAFT 3TG-00386-ABGA-TCZZA 37 Product overview Nokia FastMile 4G Receiver Product Overview Figure 6 Application example of the Nokia FastMile 4G Receiver Radio basestation Nokia FastMile 4G Receiver PoE Injector Residential gateway LTE 1 Gbps Ethernet Wi-Fi or Ethernet WiFi or Ethernet connectivity to end-user devices 28814 The Nokia FastMile 4G Receiver is available in the following model types:

Compact multi-band; this model type has the following features:

Compact mono-band; this model type has the following features:

fixed beamforming antennas multi-band transmission fixed beamforming antennas mono-band transmission ABA; this model type has the following features:

high gain beam steering antenna automated beam alignment Figure 7 shows examples of the model types of the Nokia FastMile 4G Receiver. 38 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Product overview Figure 7 Examples of model types of the Nokia FastMile 4G Receiver Compact/multi-band Compact/mono-band ABA 28770 The Nokia FastMile 4G Receiver has built-in antenna and LTE modem that provide the LTE broadband access to the network. The Nokia FastMile 4G Receiver is capable of withstanding outdoor environmental conditions. It has an IP rating of IP66 TYPE3 and can operate in the following temperature ranges:

compact mono-band and ABA models can operate in a temperature of 30C to 65C (22F to 149F) compact multi-band models can operate in a temperature of 30C to 55C

(22F to 131F); the Model 4G05-B can operate in a temperature of 40C to 55C (40F to 131F) See chapter 16 for additional specifications of the Nokia FastMile 4G Receiver. 5.2 End-to-end example The Nokia FastMile 4G Receiver can be used to provide IPTV, Internet, and VoIP services to end-users that are connected to the Nokia FastMile 4G Receiver through a Nokia-approved residential gateway or a Nokia-approved PoE injector. The Nokia FastMile 4G Receiver can also connect directly to a video monitor, personal computer, and so on rather than using a residential gateway and PoE injector. Issue: DRAFT 3TG-00386-ABGA-TCZZA 39 Product overview Nokia FastMile 4G Receiver Product Overview Due to the independence between the Nokia FastMile 4G Receiver and the gateway, the Nokia FastMile 4G Receiver also addresses the business market. The business customer can seamlessly re-use their existing business gateway. The Nokia FastMile 4G Receiver supports extended QCI and multiple APNs that can be mapped on VLANs to support QoS for different services. Figure 8 shows an end-to-end example that features the Nokia FastMile 4G Receiver with a residential gateway and PoE injector. Figure 8 End-to-end example featuring the Nokia FastMile 4G Receiver with a residential gateway and PoE injector Core IPTV Internet VoIP Radio basestation Nokia FastMile 4G Receiver PoE Injector Residential gateway LTE 1 Gbps Ethernet Wi-Fi or Ethernet WiFi or Ethernet connectivity to end-user devices that are using IPTV, internet, and VoIp 28815 5.3 Installing the Nokia FastMile 4G Receiver As part of installing the Nokia FastMile 4G Receiver, you can use the Nokia Wireless app (described in section 6.1.1) to help in determining the mounting location for the Nokia FastMile 4G Receiver with either of the following:

an ACS through TR-069 with help from the Nokia Altiplano FastMile Controller an ACS through TR-069 without help from the Nokia Altiplano FastMile Controller The Nokia FastMile 4G Receiver Installation Guide provides steps on how to use the Nokia Wireless app to help in determining the mounting location, and how to install the Nokia FastMile 4G Receiver on the side of a house or on a pole close to the house. 40 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Functional overview 6 Functional overview 6.1 Overview 6.2 LTE characteristics 6.3 Data forwarding 6.4 Ethernet characteristics 6.5 Power supply characteristics 6.6 Remote management protocols 6.1 Overview The Nokia FastMile 4G Receiver provides wireless broadband access in the form of LTE to meet the ever growing network needs of end users. The Nokia FastMile 4G Receiver is an outdoor device that lets operators use LTE to offer fixed wireless broadband to their customers. The Nokia FastMile 4G Receiver is easy to install and is user-friendly to operate. 6.1.1 Nokia Wireless app The Nokia FastMile 4G Receiver can be installed with the assistance of an Android application, known as Nokia Wireless app, installed on a mobile phone. The app in general lets you scan the QR code of the receiver, identify the best location to install the receiver by measuring the signal strength and connect to the receiver over a Bluetooth connection in order to apply configuration. The Nokia Wireless app also provides management and troubleshooting capabilities for the Nokia FastMile 4G Receiver such as the following:

viewing information that includes:

LTE cell info such as connection state, status, EARFCN, and PCI other stats (for example, bytes sent and bytes received) current and average signal stats for RSRP, RSRQ, RSSI, and SINR uploading CA certificates to the Nokia FastMile 4G Receiver resetting the 4G Receiver to factory settings rebooting the 4G Receiver Issue: DRAFT 3TG-00386-ABGA-TCZZA 41 Functional overview Nokia FastMile 4G Receiver Product Overview See the Installation guide for more information about how the Nokia Wireless app is used in the installation process. See chapter 13 in this document for more information about how Nokia Wireless app can be used for management of the Nokia FastMile 4G Receiver. 6.1.2 Web UI The Nokia FastMile 4G Receiver supports local management capability, allowing status view and configuration operations, through a Web UI for a Nokia FastMile 4G Receiver managed by an ACS through TR-069. The Web UI can be accessed directly from a laptop through the Ethernet port of the Nokia FastMile 4G Receiver via the dedicated static IP address 192.168.0.1

(https://192.168.0.1). Alternatively, it is possible to access the Web UI from behind a Nokia-approved residential gateway which is appropriately configured. It is recommended not to change or reconfigure the Nokia FastMile 4G Receiver static IP for the Web UI interface, since changing the default IP address (that is, 192.168.0.1) would impede access from the Web UI. Web UI functionality is optimized for the following browsers:

Google Chrome (version 76.0.3809.132 or greater) Mozilla Firefox (version 69.0 or greater) Microsoft Edge (version 44.18362.267.0 or greater) Note Internet Explorer is not supported since it will be replaced by Edge and will not be updated from Microsoft any more. The Web UI design is optimized for a resolution of 1920x1080 pixels, but is not restricted to it. Note The Web UI is based on https The client browser will indicate an unknown certificate warning because a Nokia signed certificate is used; this does not constitute a security issue or threat. It is safe to accept the certificate. See chapter 14 in this document for information about using the Web UI to manage the Nokia FastMile 4G Receiver. 42 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Functional overview 6.1.3 Remote management The Nokia FastMile 4G Receiver supports remote management capability, allowing management and health monitoring of it from the Nokia Altiplano FastMile Controller

(through NETCONF) or from an ACS (through TR-069). Note 1 The NETCONF version of the FastMile 4G Receiver for remote management from the Nokia Altiplano FastMile Controller is not supported from FM 2.0.03a onwards. Note 2 The Nokia FastMile 4G Receiver supports DHCP option 43 when it works as a DHCP server for the gateway by providing information about the ACS to the gateway. The relevant DHCP option 43 parameters must be configured in the preconfig.xml file. See the documentation for the Nokia Altiplano FastMile Controller for information about managing and monitoring the Nokia FastMile 4G Receiver through the Nokia Altiplano FastMile Controller. See section 6.6 for information about the remote management protocols. 6.2 LTE characteristics The following are some of the key LTE characteristics of the Nokia FastMile 4G Receiver:

LTE 3GPP Release 12 Compliant, UE Category 12 supports the E-UTRA bands listed in Table 3 transmit power: max +23 dBm +/- 2 dBm Table 3 E-UTRA bands supported by the Nokia FastMile 4G Receiver E-UTRA bands Band 42/43/48 (mono-band support) Band 42/43/48(1) (ABA support) Band 3 (mono-band support) Band 7/38/40/41 (mono-band support) Band 3/7/20/32 (multi-band support) Model 4G01-A 4G01-B 4G02-A 4G03-A 4G04-A 4G06-A 4G17-A Band 1/3/7/38/40/41/20/28 (multi-band support) 4G05-A and 4G05-B Band 2/25/4/66/7/42/43/48(2)/28 (multi-band support) Band 1/3/7/20/32 (multi-band support) Notes

(1) Note that B48 for the 4G01-B has not been tested for FCC certification and is not ready for commercial use in this release. Issue: DRAFT 3TG-00386-ABGA-TCZZA 43 Functional overview Nokia FastMile 4G Receiver Product Overview

(2) Note that FCC certification for B48 for the 4G06-A is ongoing and is not ready for commercial use in this release 6.3 Data forwarding The Nokia FastMile 4G Receiver supports the following data forwarding methods:

Table 4 Data forwarding methods supported by the Nokia FastMile 4G Receiver Forwarding mode Typical use Single APN with multi-bearers for route mode Recommended for using only one APN specific for Nokia FastMile 4G Receiver Single APN with multi-bearers for bridge mode Could be used for WAN of the Nokia FastMile 4G Receiver with VLAN tag Multiple APNs with bridge mode Used as multi-APN, separated service with APNs: each APN is for each service. Multiple APNs with mixed mode Note in this case, a specific port should be reserved for service traffic. Can be used for separated APNs on OAM and also other APNs for separated services:

Only default APN is in route mode which could be OAM Besides APN, each APN is for each service Tunnel mode Can be used for using tunnel for L2 forwarding such as PPPoE 6.4 Ethernet characteristics The following are some of the key Ethernet characteristics of the Nokia FastMile 4G Receiver:

provides a 1 Gbps Ethernet LAN Interface that, depending on the model of the Nokia FastMile 4G Receiver, has the following:

the Compact mono-band and ABA models have a pre-attached 3 m (9.8 ft) Cat5e shielded twisted pair Ethernet cable with a male RJ 45 connector at the free end; the 4G03-A Compact mono-band model is also available with a pre-attached 20 m

(65.6 ft) Cat5e shielded twisted pair Ethernet cable with a male RJ 45 connector at the free end the Compact multi-band models have a female RJ 45 connector that supports connection of a customer-supplied Ethernet cable:

- the Model 4G17-A requires << need Ethernet cable (shielded and non-shielded and max length) info and connector pinout info>>

- all other Compact multi-band models require a Cat5e shielded twisted pair Ethernet cable with standard pinouts that is up to a maximum of 80 m (262 ft) in length supports IEEE802.3 1000BASE-T 44 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Functional overview supports IEEE802.3az energy efficient Ethernet the Ethernet cable for all models is also used for power over Ethernet (PoE) as per IEEE802.3 at type-2 6.5 Power supply characteristics The following are some of the key power supply characteristics of the Nokia FastMile 4G Receiver:

powered through PoE from a Nokia-approved residential gateway, or through a Nokia-approved PoE injector (see section 11.2 for information about PoE injectors for use with the FastMile 4G Receiver) supports PoE+ as per IEEE802.3 at type-2 rating: 53 VDC at 600 mA See section 11.1 for power information. 6.6 Remote management protocols Remote management of the Nokia FastMile 4G Receiver can be done from the Nokia Altiplano FastMile Controller through NETCONF or from an ACS through TR-069/TR181 depending on the installed SIM card. Note The NETCONF version of the FastMile 4G Receiver for remote management from the Nokia Altiplano FastMile Controller is not supported from FM 2.0.03a onwards. For the first startup, the Nokia FastMile 4G Receiver starts from the NETCONF version.The Nokia FastMile 4G Receiver will automatically detect the remote management protocol through information that is on the SIM card installed in the unit. If the Nokia FastMile 4G Receiver detects that the remote management protocol on the SIM card is TR-069/TR181, it restarts and starts up with TR-069/TR181 management. If the remote management protocol is NETCONF, the Nokia FastMile 4G Receiver can be managed remotely from the Nokia Altiplano FastMile Controller. If the remote management protocol is TR-069, the Nokia FastMile 4G Receiver can be managed remotely from an ACS. Figure 9 shows the Nokia Altiplano FastMile Controller being used for remote management of the Nokia FastMile 4G Receiver. Note that NETCONF is used by the Nokia Altiplano FastMile Controller to manage the Nokia FastMile 4G Receiver, and that an ACS manages the residential gateway through TR-069. Issue: DRAFT 3TG-00386-ABGA-TCZZA 45 Functional overview Nokia FastMile 4G Receiver Product Overview Figure 9 Remote management of the Nokia FastMile 4G Receiver through the Nokia Altiplano FastMile Controller IPTV Internet Core VoIP NETCONF Nokia Altiplano Fastmile Controller ACS TR-069 Radio basestation Nokia FastMile 4G Receiver PoE Injector Residential gateway LTE 1 Gbps Ethernet Wi-Fi or Ethernet WiFi or Etherne connectivity to end-user devic that are using IPTV, internet, and VoIp 28 Figure 10 shows an ACS being used for remote management of the Nokia FastMile 4G Receiver. Note that the ACS uses TR-069 to manage both the Nokia FastMile 4G Receiver and the residential gateway. 46 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Functional overview Figure 10 Remote management of the Nokia FastMile 4G Receiver through an ACS Core IPTV Internet VoIP ACS TR-069 Radio basestation Nokia FastMile 4G Receiver PoE Injector Residential gateway LTE 1 Gbps Ethernet Wi-Fi or Ethernet WiFi or Ethernet connectivity to end-user devices that are using IPTV, internet, and VoIp 28817 Issue: DRAFT 3TG-00386-ABGA-TCZZA 47 Functional overview Nokia FastMile 4G Receiver Product Overview 48 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Model overview 7 Model overview 7.1 Models of the Nokia FastMile 4G Receiver 7.1 Models of the Nokia FastMile 4G Receiver A wide range of models are available for the Nokia FastMile 4G Receiver to support different E-UTRA bands and band combinations for LTE, including the capability to limit the bands to be used among the bands physically supported, to support network resource planning, and to speed up the cell attach speed. All models can be wall-mounted or pole-mounted. If you will be mounting the Nokia FastMile 4G Receiver on a pole, you will need kit 3TG-00291-AA that contains the pole adapter for the Nokia FastMile 4G Receiver. Note that pole strapping and wall fasteners are not provided by Nokia. Table 5 describes the E-UTRA band and frequency support and the antenna configurations for each model of the Nokia FastMile 4G Receiver. Table 5 Models of the Nokia FastMile 4G Receiver Band 3: FDD, Tx 1710 MHz 1785 MHz, Rx 1805 MHz 1880 MHz Integrated with 10.5 dBi fixed beamforming antenna Integrated with 12.5 dBi fixed beamforming antenna E-UTRA band support and frequencies Band 42: TDD, 3400 MHz 3600 MHz Band 43: TDD, 3600 MHz 3800 MHz Band 48: TDD, 3550 MHz 3700 MHz Band 42: TDD, 3400 MHz 3600 MHz Band 43: TDD, 3600 MHz 3800 MHz Band 48(1): TDD, 3550 MHz 3700 MHz Band 7: FDD, Tx 2500 MHz 2570 MHz, Rx 2620 MHz 2690 MHz Band 38: TDD, 2570 MHz 2620 MHz Band 40: TDD, 2300 MHz 2400 MHz Band 41: TDD, 2496 MHz 2690 MHz Band 3: FDD, Tx 1710 MHz 1785 MHz, Rx 1805 MHz 1880 MHz Band 7: FDD, Tx 2500 MHz 2570 MHz, Rx 2620 MHz 2690 MHz Band 20: FDD, Tx 832 MHz 862 MHz Rx 791 MHz 821 MHz Band 32: FDD, Rx 1452 MHz 1496 MHz Model 4G01-A 4G01-B 4G02-A 4G03-A 4G04-A

(1 of 2) Antenna configuration Integrated with 15 dBi fixed beamforming antenna Model type Compact mono-band Integrated with 3x4 dual polarized antenna array, electronic beam steering +/- 45 horizontally, and up to 17 dBi peak antenna gain with beam steering ABA Compact mono-band Compact mono-band Compact multi-band Band 7 is integrated with > 11 dBi fixed beamforming antenna Band 3 is integrated with > 10 dBi fixed beamforming antenna Band 32 is integrated with > 8.3 dBi fixed beamforming antenna Band 20 is integrated with > 2.5dBi fixed beamforming antenna Issue: DRAFT 3TG-00386-ABGA-TCZZA 49 Model overview Nokia FastMile 4G Receiver Product Overview Model 4G05-A 4G05-B 4G06-A 4G17-A

(2 of 2) 50 E-UTRA band support and frequencies Band 1: FDD, Tx 1920 MHz 1980 MHz, Rx 2110 MHz 2170 MHz Band 3: FDD, Tx 1710 MHz 1785 MHz, Rx 1805 MHz 1880 MHz Band 7: FDD, Tx 2500 MHz 2570 MHz, Rx 2620 MHz 2690 MHz Band 38: TDD, 2570 MHz 2620 MHz Band 40: TDD, 2300 MHz 2400 MHz Band 41: TDD, 2496 MHz 2690 MHz Band 20: FDD, Tx 832 MHz 862 MHz, Rx 791 MHz 821 MHz Band 28: FDD, Tx 703 MHz 748 MHz, Rx 758 MHz - 803 MHz Band 1: FDD, Tx 1920 MHz 1980 MHz, Rx 2110 MHz 2170 MHz Band 3: FDD, Tx 1710 MHz 1785 MHz, Rx 1805 MHz 1880 MHz Band 7: FDD, Tx 2500 MHz 2570 MHz, Rx 2620 MHz 2690 MHz Band 38: TDD, 2570 MHz 2620 MHz Band 40: TDD, 2300 MHz 2400 MHz Band 41: TDD, 2496 MHz 2690 MHz Band 20: FDD, Tx 832 MHz 862 MHz, Rx 791 MHz 821 MHz Band 28: FDD, Tx 703 MHz 748 MHz, Rx 758 MHz - 803 MHz Band 2: FDD, Tx 1850 MHz - 1910 MHz, Rx 1930 MHz - 1990 MHz Band 25: FDD, Tx 1850 MHz - 1915 MHz, Rx 1930 MHz - 1995 MHz Band 4: FDD, Tx 1710 MHz - 1755 MHz, Rx 2110 MHz - 2155 MHz Band 66: FDD, Tx 1710 MHz - 1780 MHz, Rx 2110 MHz - 2200 MHz Band 7: FDD, Tx 2500 MHz - 2570 MHz, Rx 2620 MHz - 2690 MHz Band 42: TDD, 3400 MHz - 3600 MHz Band 43: TDD, 3600 MHz - 3800 MHz Band 48(2): TDD, 3550 MHz - 3700 MHz;

Band 28: FDD, Tx 703 MHz - 748 MHz, Rx 758 MHz -- 803 MHz Band 1: FDD, Tx 1920 MHz -1980 MHz, Rx 2110 MHz -2170 MHz Band 3: FDD, Tx 1710 MHz -1785 MHz, Rx 1805 MHz - 1880 MHz Band 7: FDD, Tx 2500 MHz - 2570 MHz, Rx 2620 MHz - 2690 MHz Band 20: FDD, Tx 832 MHz - 862 MHz, Rx 791 MHz - 821 MHz Band 32: FDD, Rx 1452 MHz - 1496 MHz Antenna configuration Model type Bands 7, 38, 40, and 41 are integrated with > 11 dBi fixed beamforming antenna Compact multi-band Bands 1 and 3 are integrated with > 10 dBi fixed beamforming antenna Bands 20 and 28 are integrated with > 2.5 dBi fixed beamforming antenna Bands 7, 38, 40, and 41 are integrated with > 11 dBi fixed beamforming antenna Bands 1 and 3 are integrated with > 10 dBi fixed beamforming antenna Bands 20 and 28 are integrated with > 2.5 dBi fixed beamforming antenna Compact multi-band similar to Model 4G05-A but for use in colder temperatures Bands 2, 25, 4, and 66 are integrated with > 9.3 dBi fixed beamforming antenna Compact multi-band Bands 7 is integrated with > 11 dBi fixed beamforming antenna Bands 42, 43 and 48(2) are integrated with > 11 dBi fixed beamforming antenna Band 28 is integrated with > 2.5 dBi fixed beamforming antenna Band 7 is integrated with > 11 dBi fixed beamforming antenna Compact multi-band Bands 1 and 3 are integrated with > 10 dBi fixed beamforming antenna Band 32 is integrated with > 8.3 dBi fixed beamforming antenna Band 20 is integrated with > 2.5dBi fixed beamforming antenna 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Model overview Notes

(1) Note that B48 for the 4G01-B has not been tested for FCC certification and is not ready for commercial use in this release.

(2) Note that FCC certification for B48 for the 4G06-A is ongoing and is not ready for commercial use in this release. 7.1.1 Label information Table 6 describes the label information for the Nokia FastMile 4G Receiver. Table 6 Label information for the Nokia FastMile 4G Receiver Model 4G01-A 4G01-B 4G02-A 4G03-A 4G04-A 4G05-A 4G05-B 4G06-A 4G17-A Product details Nokia FM compact Nokia FM ABA Nokia FM compact Nokia FM compact Nokia FM compact Nokia FM compact Nokia FM compact Nokia FM compact Nokia FM compact Issue: DRAFT 3TG-00386-ABGA-TCZZA 51 Model overview Nokia FastMile 4G Receiver Product Overview 52 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Physical interfaces 8 Physical interfaces 8.1 Physical interfaces of the Compact mono-band and ABA models 8.2 Physical interfaces of the Compact multi-band models 8.1 Physical interfaces of the Compact mono-band and ABA models Table 7 describes the physical interfaces of the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver. Table 7 Physical interfaces of the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver Interface Description Ground point Point for connecting to external ground. Connection to the ground point is not required. Located on the underside of the unit; see Figure 11. Ethernet cable Ethernet connectivity for the Compact mono-band and ABA models is through a pre-attached 3 m (9.8 ft) cat5e shielded Ethernet cable; the same cable is also used for power (PoE as per IEEE802.3 at type-2). PoE must be provided by a Nokia-approved residential gateway or a Nokia-approved PoE injector (see section 11.2 for information about PoE injectors for use with the FastMile 4G Receiver). The 4G03-A Compact mono-band model is also available with a pre-attached 20 m (65.6 ft) Cat5e shielded twisted pair Ethernet cable. Located on the underside of the unit; see Figure 11. The pre-attached Ethernet cable has a male RJ 45 connector at the free end. An additional length of cat5e shielded Ethernet cabling can be attached to the Ethernet cable up to a maximum of 80 m (262 ft) in combined length. A waterproof IP67 female RJ 45 plug is needed to connect the Ethernet cabling to the Ethernet cable of the Nokia FastMile 4G Receiver. Status LED Single multifunction LED that indicates status information for the Nokia FastMile 4G Receiver. Located on the underside of the unit; see Figure 11. See section 10.1 for the behavior of the status LED of the Compact mono-band and ABA models. Reset button Button to reset the Nokia FastMile 4G Receiver. Located on the underside of the unit; see Figure 11.

(1 of 2) Issue: DRAFT 3TG-00386-ABGA-TCZZA 53 Physical interfaces Nokia FastMile 4G Receiver Product Overview Interface SIM slot Description Slot for Nano/4FF SIM card for a Compact mono-band model or ABA model of the Nokia FastMile 4G Receiver. Located on the underside of the unit; see Figure 11. If the SIM card needs to be replaced, the Nokia FastMile 4G Receiver needs to be put in a powered off state before the SIM card can be removed and the new one inserted See section 9.1 for SIM card information for the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver.

(2 of 2) Figure 11 shows the location of the physical interfaces on the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver. Figure 11 Location of physical interfaces on the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver Ground point Ethernet Cable SIM slot Status LED Reset button 28797 8.2 Physical interfaces of the Compact multi-band models Table 8 describes the physical interfaces of Compact multi-band models of the Nokia FastMile 4G Receiver. Table 8 Physical interfaces of the Compact multi-band models of the Nokia FastMile 4G Receiver Interface Description Ground point Point for connecting to external ground. Connection to the ground point is not required. Located on the back of the unit; see Figure 12.

(1 of 2) 54 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Physical interfaces Interface Description Ethernet port The Compact multi-band models have a female RJ 45 connector for attaching a customer-supplied Ethernet cable:

the Model 4G17-A has a floating ground design that supports << need Ethernet cable (shielded/un-shielded and length) and connector pinout info

all other Compact multi-band models require a cat5e shielded Ethernet cable with standard pinouts that is a maximum of 80 m (262 ft) in length The same Ethernet cable is also used for power (PoE as per IEEE802.3 at type-2). PoE must be provided by a Nokia-approved residential gateway or a Nokia-approved PoE injector (see section 11.2 for information about PoE injectors for use with the FastMile 4G Receiver). The Ethernet port is located on the underside of the unit; see Figure 13. Status LED Single multifunction LED that indicates status information for the Nokia FastMile 4G Receiver. Located on the top of the unit. See section 10.1 for a figure showing the location of the status LED of the Compact multi-band models and information about its behavior. Signal strength LEDs The Compact multi-band models have a set of five LEDs that work together to indicate the LTE signal strength detected by the Nokia FastMile 4G Receiver. Located on the top of the unit. See section 10.2 for a figure showing the location of the signal strength LEDs and information about their behavior. Measurement button Button to activate the signal strength LEDs. Located on the side of the unit. See section 10.2 for a figure showing the location of the measurement button and information about using it to activate the signal strength LEDs. Reset button Button to reset the Nokia FastMile 4G Receiver. Located on the underside of the unit; see Figure 13. SIM slot Slot for Nano/4FF SIM card for a Compact multi-band model of the Nokia FastMile 4G Receiver. Located on the underside of the unit; see Figure 13. See section 9.2 for SIM card information for the Compact multi-band models of the Nokia FastMile 4G Receiver.

(2 of 2) Figure 12 shows the location of the ground point for the Compact multi-band models of the Nokia FastMile 4G Receiver. Issue: DRAFT 3TG-00386-ABGA-TCZZA 55 Physical interfaces Nokia FastMile 4G Receiver Product Overview Figure 12 Location of the ground point for the Compact multi-band models of the Nokia FastMile 4G Receiver Figure 13 shows the location of the physical interfaces that are on the underside of the Compact multi-band models of the Nokia FastMile 4G Receiver. Figure 13 Location of physical interfaces on the underside of the Compact multi-band models of the Nokia FastMile 4G Receiver Vent M6 Ethernet port SIM slot Reset button Ground point 28798 28771 56 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview SIM cards 9 SIM cards 9.1 SIM card information for the Compact mono-band and ABA models 9.2 SIM card information for the Compact multi-band models 9.1 SIM card information for the Compact mono-band and ABA models The SIM card installed in the Nokia FastMile 4G Receiver allows the Nokia FastMile 4G Receiver to connect to the LTE network and determines the remote management protocol supported for the Nokia FastMile 4G Receiver; see section 6.6 for more information about remote management. Figure 14 shows a detailed view of the SIM card slot on the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver. Figure 14 Detailed view of SIM card slot on the Compact mono-band and ABA models The Nokia FastMile 4G Receiver Installation Guide provides detailed steps for inserting the SIM card. The SIM card must be appropriate for the remote management protocol to be used for the Nokia FastMile 4G Receiver. 28642 Issue: DRAFT 3TG-00386-ABGA-TCZZA 57 SIM cards Nokia FastMile 4G Receiver Product Overview 9.2 SIM card information for the Compact multi-band models The SIM card installed in the Nokia FastMile 4G Receiver allows the Nokia FastMile 4G Receiver to connect to the LTE network and determines the remote management protocol supported for the Nokia FastMile 4G Receiver; see section 6.6 for more information about remote management. Figure 15 shows a detailed view of the SIM card slot on the Compact multi-band models of the Nokia FastMile 4G Receiver. Figure 15 Detailed view of SIM card slot on the Compact multi-band models The Nokia FastMile 4G Receiver Installation Guide provides detailed steps for inserting the SIM card. The SIM card must be appropriate for the remote management protocol to be used for the Nokia FastMile 4G Receiver. 28802 58 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview LEDs 10 LEDs 10.1 Status LED 10.2 Signal strength LEDs 10.1 Status LED All models of the Nokia FastMile 4G Receiver have a status LED:

Figure 16 shows the location of the status LED on the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver Figure 17 shows the location of the status LED on the Compact multi-band models of the Nokia FastMile 4G Receiver Figure 16 Location of the status LED on the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver Figure 17 Location of the status LED on the Compact multi-band models of the Nokia FastMile 4G Receiver 28799 28772 Status LED Status LED Issue: DRAFT 3TG-00386-ABGA-TCZZA 59 LEDs Nokia FastMile 4G Receiver Product Overview The status LED behaves differently depending on whether the Nokia FastMile 4G Receiver is managed from:

the Nokia Altiplano FastMile Controller (through NETCONF): see Table 9 an ACS (through TR-069): see Table 10 Note The NETCONF version of the FastMile 4G Receiver for remote management from the Nokia Altiplano FastMile Controller is not supported from FM 2.0.03a onwards Table 9 Status LED behavior for Nokia FastMile 4G Receiver managed from the Nokia Altiplano FastMile Controller LED color LED priority LED behavior Status information Blue First priority Blinking Bluetooth connection in progress Red Second priority Blinking Critical alarm Green Third priority Blinking twice per second Kernel and application start up Blinking one per second Application start up Bluetooth connection established No Bluetooth connection Major or minor alarm No alarm Start up OAM link is established Table 10 Status LED behavior for Nokia FastMile 4G Receiver managed from an ACS LED color LED priority LED behavior Status information Blue First priority Blinking Bluetooth connection in progress Green Second priority Blinking twice per second Kernel and application start up Bluetooth connection established No Bluetooth connection Blinking one per second Application start up Start up Software is stable Solid Off Solid Off Solid Off Solid Off Solid Off 60 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview LEDs 10.2 Signal strength LEDs Five signal strength LEDs are provided on the Compact multi-band models of the Nokia FastMile 4G Receiver as shown in Figure 18. Figure 18 Location of the signal strength LEDs Signal strength LEDs 28773 The signal strength LEDs can be activated by pressing the measurement button on the side of the Compact multi-band models of the Nokia FastMile 4G Receiver. Figure 19 shows the location of the measurement button. Figure 19 Location of the measurement button Measurement button 28885 Issue: DRAFT 3TG-00386-ABGA-TCZZA 61 LEDs Nokia FastMile 4G Receiver Product Overview The signal strength LEDs act as a set to indicate the LTE signal strength detected by the Nokia FastMile 4G Receiver. For example, if the signal strength is fourth level, then LEDs 1, 2, 3, and 4 are lit. Table 11 lists the threshold values for the signal strength LEDs, but note that the threshold values can be changed through an ACS. Table 11 Signal strength LED threshold values Number of lit LEDs None One Two Three Four Five Threshold

<-110dBm

-110 to -106 dBm

-105 to -101dBm

-100 to -96dBm

-95 to -91dBm

>=-90dBm 62 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Power information 11 Power information 11.1 Power information for the Nokia FastMile 4G Receiver 11.2 Available PoE injectors 11.1 Power information for the Nokia FastMile 4G Receiver The Nokia FastMile 4G Receiver receives power though a Cat5e shielded Ethernet cable that must be connected to a Nokia-approved residential gateway or a Nokia-approved PoE injector (see section 11.2 for information about PoE injectors available from Nokia for use with the FastMile 4G Receiver). Compact mono-band and ABA models have a pre-attached Cat5e shielded twisted pair Ethernet cable with a male RJ 45 connector at the free end. An additional length of cat5e shielded Ethernet cabling can be attached to the Ethernet cable up to a maximum of 80 m (262 ft) in combined length. A waterproof IP67 female RJ 45 plug is needed to connect the Ethernet cabling to the Ethernet cable of the Nokia FastMile 4G Receiver. See section 8.1 for more information about the pre-attached Ethernet cable. Compact multi-band models have an Ethernet port that has a female RJ 45 connector, and require a customer-supplied Ethernet cable (See section 8.2 for more information about the Ethernet port):

the Model 4G17-A has a floating ground design that supports << need Ethernet cable (shielded/un-shielded and length) and connector pinout info>>

all other Compact multi-band models require a cat5e shielded Ethernet cable with standard pinouts that is a maximum of 80 m (262 ft) in length See section 12.4 for power consumption information. 11.2 Available PoE injectors If the Nokia FastMile 4G Receiver is going to be powered through a PoE injector, the PoE injector must be a Nokia-approved PoE injector. The following classes of PoE injectors are available from Nokia for use with the FastMile 4G Receiver:

Class I: can comply with EN 60950-1 if grounding is provided on the wall socket;

should be put as close as possible to the place where the Ethernet cable enters the home Class II: can comply with EN 60950-1 if no grounding is provided on the wall socket; can also be used if grounding is provided on the wall socket Issue: DRAFT 3TG-00386-ABGA-TCZZA 63 Power information Nokia FastMile 4G Receiver Product Overview The following tables list the PoE injectors that are available from Nokia for use with the FastMile 4G Receiver:

Table 12 lists the PoE injectors that are available from Nokia for use with the Model 4G05-B Model 4G17-A Table 13 lists the PoE injectors that are available from Nokia for use with the Table 14 lists the PoE injectors that are available from Nokia for use with all other models of the FastMile 4G Receiver Table 12 Available PoE injectors for Model 4G05-B Class Model Description Color Vendor part number Class I 15w Class I PoE injector White 3TG-01541-AB G1344A-530-030-PSE1000, CH-231+CH-706,White,EU PoE+15w ClassI, MAINS CORD TYPE E&F-EU Table 13 Available PoE injectors for Model 4G17-A Class Model Description Color Vendor part number Class II 15w Class II PoE injector White 3TG-01541-BB G1344B-530-030-PSE1000, CH-221+CH-705,White,EU PoE+15w ClassII, MAINS CORD TYPE C-EU Nokia part number Nokia part number 64 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Power information Table 14 Available PoE injectors for models other than Model 4G05-B and Model 4G17-A Class Model Description Color Vendor part number Nokia part number Class I 30w FWAPoE1-CB-US-W White 3TG-00041-AA G0545-530-060-PSE1000, CH-331C+CH-706,White,US 30w G0545 53V0.6A, MAINS CORD TYPE B-US 30wFWAPoE1-CEF-EU-W 30w G0545 53V0.6A, MAINS CORD TYPE E&F-EU White 3TG-00041-AB G0545-530-060-PSE1000, CH-231+CH-706,White,EU 30w FWAPoE1-CG-UK-W White 3TG-00041-AC G0545-530-060-PSE1000, CH-1601+CH-706,White,UK 30w G0545 53V0.6A, MAINS CORD TYPE G-UK 30w FWAPoE1-CI-CCC-W 30w G0545 53V0.6A, MAINS CORD TYPE I-CCC White 3TG-00041-AD G0545-530-060-PSE1000, CH-133+CH-706,White,CCC 30w FWAPoE1-CI-AU-W White 3TG-00041-AE G0545-530-060-PSE1000, CH-1231+CH-706,White,AU 30w G0545 53V0.6A, MAINS CORD TYPE I-AU 30wFWAPoE1-CB-PSE-W 30w G0545 53V0.6A, MAINS CORD TYPE B-PSE 30w FWAPoE1-CD-BIS-W 30w G0545 53V0.6A, MAINS CORD TYPE D-BIS White 3TG-00041-AF G0545-530-060-PSE1000, CH-1131+CH-1106,White,PSE White 3TG-00041-AG G0545-530-060-PSE1000, CH-2002+CH-706,White,BIS Class II 30w FWAPoE1-CC-EU-W White 3TG-00041-BB G0545N-530-060-PSE1000, CH-221+CH-706,White,EU 30w G0545 53V0.6A, MAINS CORD TYPE C-EU Issue: DRAFT 3TG-00386-ABGA-TCZZA 65 Power information Nokia FastMile 4G Receiver Product Overview 66 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Performance information 12 Performance information 12.1 Performance overview 12.2 Throughput information 12.3 Carrier aggregation information 12.4 Power consumption information 12.1 Performance overview This chapter provides the following performance information for the Nokia FastMile 4G Receiver:

throughput information: see section 12.2 carrier aggregation information: see section 12.3 power consumption information: section 12.4 Some performance metrics for the Nokia FastMile 4G Receiver can be viewed through the Nokia Wireless app or Web UI or accessed through the Nokia Altiplano FastMile Controller:

see chapter 13 for more information about viewing information for the Nokia FastMile 4G Receiver through the Nokia Wireless app see chapter 14 for more information about viewing information for the Nokia FastMile 4G Receiver through the Web UI see the documentation for the Nokia Altiplano FastMile Controller for more information about accessing information for the Nokia FastMile 4G Receiver through the Nokia Altiplano FastMile Controller 12.2 Throughput information Table 15 provides LTE throughput information for the Nokia FastMile 4G Receiver. Table 15 LTE throughput information Mode UDP DL (3CA) TCP DL (3CA) UDP UL TCP UL FDD TDD 560M 415M 360M 360M 73M 14M 73M 18M Issue: DRAFT 3TG-00386-ABGA-TCZZA 67 Performance information Nokia FastMile 4G Receiver Product Overview The results in the above table are based on the following:

Downlink: DL 3xCA 2x2MIMO 256 QAM Uplink: single carrier 64 QAM FDD inter-band 3CA TDD Band 41 intra-Band 2CA, configuration is configuration 2, subframe 7 Base Bandwidth 20M Data rates can have a margin of 2%

Packet length is 1470B for UDP Window is 1000k for TCP Data rates are for IPv4 cases Data forwarding working on router model The end-to-end throughput is achieved in the conductive mode with cable connected. Ethernet throughput for the Nokia FastMile 4G Receiver is as per standard Ethernet 1000BASE-T, with a maximum of 1000 Mbps. The Ethernet link gets negotiated at 1000 Mbps when a residential gateway or a PoE injector is connected to the Nokia FastMile 4G Receiver. 12.3 Carrier aggregation information The following tables provide carrier aggregation support information for the Nokia FastMile 4G Receiver:

Model 4G01-A and 4G01-B (2*2 MIMO downlink with SISO uplink): Table 16 Model 4G02-A (2*2 MIMO downlink with SISO uplink): Table 17 Model 4G03-A (2*2 MIMO downlink with SISO uplink): Table 18 Model 4G04-A (2*2 MIMO downlink with SISO uplink): Table 19 Model 4G05-A and 4G05-B (2*2 MIMO downlink): Table 20 Model 4G06-A (2*2 MIMO downlink): Table 21 Model 4G17-A (2*2 MIMO downlink with SISO uplink): Table 22 Note 1 B48 for the 4G01-B has not been tested for FCC certification and is not ready for commercial use in this release. Note 2 FCC certification for B48 for the 4G06-A is ongoing and is not ready for commercial use in this release. 68 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Performance information Table 16 Carrier aggregation support for Model 4G01-A and Model 4G01-B

(2*2 MIMO downlink with SISO uplink) Index Downlink Upload PCC SCC1 SCC2 SCC3 PCC SCC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

(1 of 3) 42A 43A 42C 43C 48C 42A 43A 48A 42A 43A 42C 43C 48C 42A 43A 48A 42A 43A 42A 42A 43A 43A 42D 43D 48D 42A 43A 48A 42A 43A 42A 43A 42A 42A 43A 48A 43A 42A 42A 43A 48A 43C 42C 42A 43A 43A 42A 42A 43A 48A 43C 42C 42A 43A 43A 42A 42A 42A 43A 48A 43A 42A 43A 42C 43C 48C 42A 43A 48A 43A 42A 42A 43A 48A 42A 43A 42A 43A 42A 42A Issue: DRAFT 3TG-00386-ABGA-TCZZA 69 Performance information Nokia FastMile 4G Receiver Product Overview Index Downlink Upload PCC SCC1 SCC2 SCC3 PCC SCC 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

(2 of 3) 42A 43A 43A 42D 43D 48D 42A 43A 48A 42A 43A 42A 42A 42A 43A 43A 43A 42E 43E 48E 42A 43A 48A 42A 43A 42A 42A 42A 43A 43A 43A 42E 43E 43A 42A 42A 42A 43A 48A 42A 43A 43A 42A 42A 43A 42A 43A 48A 42A 43A 43A 42A 42A 43A 43A 43A 42A 42A 43A 48A 42A 43A 43A 42A 43A 43A 42A 43A 48A 43D 42D 42A 42A 43A 42A 43A 43A 43A 43A 43A 42A 42A 42A 42A 43A 48A 43A 43A 43A 42A 42A 42A 43A 42A 42A 42A 43A 42A 43A 43A 42A 43A 42A 42A 42A 43A 43A 43A 42C 43C 70 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Performance information Downlink PCC 48E 42A 43A 48A SCC1 SCC2 SCC3 42A 43A 48A 42A 43A 48A 42A 43A 48A Upload PCC 48C 42A 43A 48A SCC 42A 43A 48A Carrier aggregation support for Model 4G02-A (2*2 MIMO down-

link with SISO uplink) Index Downlink Uplink PCC SCC1 PCC SCC1 3C 3A 3C 3A 3D 3D 3E 3E 3A 3A 3A 3C 3A 3C 3C Table 18 Carrier aggregation support for Model 4G03-A (2*2 MIMO down-

link with SISO uplink) index Downlink SCC SCC Uplink PCC Index 65 66 67 68

(3 of 3) Table 17 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9

(1 of 2) PCC 7C 38C 40C 41C 7A 38A 40A 41A 7C 7A 38A 40A 41A 7C Issue: DRAFT 3TG-00386-ABGA-TCZZA 71 Performance information Nokia FastMile 4G Receiver Product Overview index Downlink PCC SCC 38C 40C 41C 7A 38A 40A 41A 7D 38D 40D 41D 7C 38C 40C 41C 7D 38D 40D 41D 7C 38C 40C 41C 40E 41E 40C 41C 40E 41E 40C 41C 7A 38A 40A 41A 7A 38A 40A 41A 7A 38A 40A 41A 40C 41C 40C 41C Uplink PCC 38C 40C 41C 7A 38A 40A 41A 7C 38C 40C 41C 7A 38A 40A 41A 40C 41C 40A 41A SCC 7A 38A 40A 41A 7A 38A 40A 41A 40A 41A 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

(2 of 2) 72 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Performance information Table 19 Carrier aggregation support for Model 4G04-A (2*2 MIMO down-

link with SISO uplink) Index Downlink PCC SCC1 SCC2 SCC1 Uplink PCC 3A 3A 7A 20A 7A 20A 7A 20A 3A 3A 20A 7A 20A 20A 3A 32A 32A Table 20 Carrier aggregation support for Model 4G05-A and Model 4G05-B

(2*2 MIMO downlink) Index Downlink PCC SCC1 SCC2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5

(1 of 5) 3A 3A 3A 7A 20A 7A 7A 20A 20A 3A 3A 7A 20A 7A 20A 3A 7A 20A 3A 20A 1A 3A 1A 7A 1A 7A 20A 32A 3A 3A 20A 32A 7A 32A 7A 20A 3A 3A 20A 7A 7A 3A 7A 20A 3A 3A 1A 7A 1A 38A Issue: DRAFT 3TG-00386-ABGA-TCZZA 73 Performance information Nokia FastMile 4G Receiver Product Overview Index Downlink SCC1 SCC2 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38

(2 of 5) PCC 38A 1A 41A 3A 7A 3A 20A 3A 28A 3A 38A 3A 40A 3A 41A 28A 40A 28A 41A 3C 28C 40C 41C 1A 3C 1C 7A 3A 7C 3A 38C 3A 40C 1A 41A 1A 7A 3A 20A 3A 28A 3A 38A 3A 40A 3A 41A 3A 40A 28A 41A 28A 3C 1A 7A 1C 7C 3A 38C 3A 40C 3A 74 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Performance information Index Downlink SCC1 SCC2 7A 7A 1A 38A 38A 1A 41A 41A 1A 40A 40A 3A 41A 41A 3A 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71

(3 of 5) PCC 3A 41C 28A 40C 28A 41C 1A 3A 7A 1A 3A 38A 1A 3A 41A 3A 28A 40A 3A 28A 41A 41D 1C 3C 1A 3D 3C 7C 3A 7D 3C 38C 3A 41C 3A 40C 28A 41C 28A 3A 1A 3A 3A 1A 3A 3A 1A 3A 28A 3A 28A 28A 3A 28A 3C 1C 3D 1A 7C 3C 7D 3A 38C 3C 38D Issue: DRAFT 3TG-00386-ABGA-TCZZA 75 Performance information Nokia FastMile 4G Receiver Product Overview Index SCC1 SCC2 Downlink PCC 38D 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104

(4 of 5) 3C 40C 3A 40D 3C 41C 3A 41D 28C 40C 28A 40D 28C 41C 28A 41D 1A 3A 7C 1A 3C 7A 1A 3A 38C 1A 3C 38A 1A 3A 41C 1A 3A 40C 3C 40D 3A 41C 3C 41D 3A 40C 28C 40D 28A 41C 28C 41D 28A 3A 1A 3A 3C 1A 3C 3A 1A 3A 3C 1A 3C 3A 1A 3A 3C 7C 7C 1A 7A 7A 1A 38C 38C 1A 38A 38A 1A 41C 41C 1A 41A 76 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Performance information Index Downlink PCC SCC1 SCC2

(5 of 5) Table 21 Carrier aggregation support for Model 4G06-A (2*2 MIMO down-

link) Index Downlink PCC SCC1 SCC2 SCC3 41A 1A 40C 40C 3A 40A 40A 3A 41C 41C 3A 41A 41A 3A 105 106 107 108 109 110 111 112 113 114 115 116 117 118 1 2 3 4 5 6 7 8 9 10 11 12 13

(1 of 5) 3C 41A 3A 28A 40C 3A 28C 40A 3A 28A 41C 3A 28C 41A 2A 4A 2A 7A 2A 28A 2A 42A 2A 48A 2A 66A 4A 1A 3C 28A 3A 28A 28C 3A 28C 28A 3A 28A 28C 3A 28C 4A 2A 7A 2A 28A 2A 42A 2A 48A 2A 66A 2A 7A Issue: DRAFT 3TG-00386-ABGA-TCZZA 77 Performance information Nokia FastMile 4G Receiver Product Overview Index Downlink PCC SCC1 SCC2 SCC3 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 28 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

(2 of 5) 4A 28A 4A 42A 4A 43A 4A 28A 7A 42A 7A 43A 7A 66A 7A 42A 28A 43A 28A 66A 28A 66A 42A 66A 43A 7A 4A 28A 4A 42A 4A 43A 7A 28A 7A 42A 7A 43A 7A 66A 28A 42A 28A 43A 28A 66A 42A 66A 43A 66A 2C 4C 7C 25C 28C 42C 43C 48C 78 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Performance information Index Downlink SCC1 SCC2 SCC3 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

(3 of 5) 28A 28A 4A 48A 48A 4A 42A 42A 7A 42A 42A 28A 43A 43A 28A 66A 66A 28A 66A 66A 48A 28A 28A 7A 42A 42A 7A 43A 43A 7A 42A 42A PCC 66C 2A 4A 28A 2A 4A 48A 2A 7A 42A 2A 28A 42A 2A 28A 43A 2A 28A 66A 2A 48A 66A 4A 7A 28A 4A 7A 42A 4A 7A 43A 4A 28A 4A 2A 2A 4A 2A 2A 7A 2A 2A 28A 2A 2A 28A 2A 2A 28A 2A 2A 48A 2A 2A 7A 4A 4A 7A 4A 4A 7A 4A 4A 28A 4A Issue: DRAFT 3TG-00386-ABGA-TCZZA 79 Performance information Nokia FastMile 4G Receiver Product Overview Index Downlink PCC SCC1 SCC2 SCC3 28A 43A 43A 28A 66A 66A 28A 66A 66A 42A 66A 66A 43A 66A 66A 42A 66A 66A 43A 28A 28A 4A 28A 28A 28A 4A 28A 42A 42A 7A 42A 43A 43A 42A 42A 42A 4A 43A 43A 43A 4A 66A 66A 66A 7A 66A 66A 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112

(4 of 5) 42A 4A 28A 43A 7A 28A 66A 7A 42A 66A 7A 43A 66A 28A 42A 66A 28A 43A 66A 4A 7A 28A 42A 4A 7A 28A 43A 7A 28A 42A 66A 7A 28A 4A 28A 4A 4A 28A 7A 7A 42A 7A 7A 43A 7A 7A 42A 28A 28A 43A 28A 28A 7A 4A 7A 7A 7A 4A 7A 7A 28A 7A 28A 28A 28A 7A 80 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Performance information Index Downlink 113 114

(5 of 5) Table 22 PCC 43A 66A SCC1 28A 28A SCC2 7A 43A SCC3 66A 7A Carrier aggregation support for Model 4G17-A (2*2 MIMO down-

link with SISO uplink) Index Downlink Uplink PCC SCC1 SCC2 SCC3 PCC SCC1 SCC2 1A 3A 1A 7A 3A 7A 1A 3A 7A 1A 3A 1A 7A 3A 1A 3A 7A 1A 3A 3A 7A 1A 7A 1A 3A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

(1 of 2) 3A 1A 7A 1A 7A 3A 32A 32A 32A 3A 1A 7A 1A 7A 3A 1A 3A 3A 1A 7A 3A 7A 1A 3A 1A 7A 7A 1A 32A 32A 32A 32A 32A 32A 7A 7A 1A 3A 1A 7A 3A 3A 1A 7A 1A 7A 1A 3A 3A 1A Issue: DRAFT 3TG-00386-ABGA-TCZZA 81 Performance information Nokia FastMile 4G Receiver Product Overview Index Downlink Uplink PCC SCC1 SCC2 SCC3 PCC SCC1 SCC2 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

(2 of 2) 1A 7A 3A 7A 1A 3A 3A 7A 1A 7A 1A 3A 7A 1A 3A 1A 7A 3A 7A 3A 3A 1A 3A 3A 1A 7A 3A 7A 1A 3A 1A 3A 3A 1A 3A 3A 1A 1A 1A 7A 3A 7A 1A 3A 3A 1A 1A 3A 1A 7A 3A 7A 32A 32A 32A 32A 32A 32A 32A 32A 32A 3A 3A 1A 7A 3A 7A 1A 3A 1A 7A 1A 7A 7A 1A 7A 3A 12.4 Power consumption information Table 23 provides power consumption information for all models of the Nokia FastMile 4G Receiver. Table 23 Power consumption information for all models Condition Idle power Maximum power output Power consumption 12W 1.6 W 82 3TG-00386-ABGA-TCZZA Issue: DRAFT 7A 1A 7A 1A 32A 32A 32A 32A 32A 32A 7A 7A 1A 7A 7A 7A 1A 7A 3A Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app 13 Management using the Nokia Wireless app 13.1 Using the Nokia Wireless app to manage the Nokia FastMile 4G Receiver 13.2 Using the Nokia Wireless app to manage a unit managed by the Nokia Altiplano FastMile Controller 13.3 Using the Nokia Wireless app to manage a unit managed by an ACS 13.1 Using the Nokia Wireless app to manage the Nokia FastMile 4G Receiver After the Nokia FastMile 4G Receiver has been installed as described in the installation guide, you can use the Nokia Wireless app to perform management activities on it, such as viewing information, uploading CA certificates, rebooting the Nokia FastMile 4G Receiver, or resetting to factory settings. The user of the Nokia Wireless app has to agree with the Terms of Service and the Nokia Privacy Policy that define the app. This is a mandatory step during the first start up of the app. Terms of Service can be found inside the Nokia Wireless app whereas a link is provided to the Nokia Privacy Policy, which is described in the Nokia public webpage. The user can find this information later on by visiting the About screen of the app. Figure 20 shows the Before we begin screen that provides access to the Terms of Service and the Nokia Privacy Policy. Issue: DRAFT 3TG-00386-ABGA-TCZZA 83 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 20 Before we begin screen Figure 21 shows the Terms of Service screen that is accessed through the Before we begin screen. 84 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 21 Terms of Service screen The Nokia Wireless app is protected as much as possible against malicious users. Tools like obfuscation and encryption used by the Nokia Wireless app, as well as runtime checks and tamper detection, make it hard for malicious users to understand the code flow or to hack the application. There are some differences in managing the Nokia FastMile 4G Receiver through the Nokia Wireless app depending on whether the Nokia FastMile 4G Receiver is managed remotely by the Nokia Altiplano FastMile Controller (through NETCONF) or by an ACS (through TR-069):

if the Nokia Altiplano FastMile Controller is being used for remote management of the Nokia FastMile 4G Receiver (through NETCONF), see section 13.2 if an ACS is being used for remote management of the Nokia FastMile 4G Receiver (through TR-069), see section 13.3 Issue: DRAFT 3TG-00386-ABGA-TCZZA 85 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview 13.2 Using the Nokia Wireless app to manage a unit managed by the Nokia Altiplano FastMile Controller If the Nokia Altiplano FastMile Controller is being used for remote management of the Nokia FastMile 4G Receiver (through NETCONF), you can use the Nokia Wireless app to perform management activities on it, such as viewing information, uploading CA certificates, rebooting the Nokia FastMile 4G Receiver, or resetting to factory settings, as described in the following procedure. Note The NETCONF version of the FastMile 4G Receiver for remote management from the Nokia Altiplano FastMile Controller is not supported from FM 2.0.03a onwards. You will need the QR code that was saved as described during installation the Nokia FastMile 4G Receiver in order to scan it when logging in to it through the Nokia Wireless app. Logging in to the Nokia FastMile 4G Receiver also includes the following:

initiating a Bluetooth connection enabling Bluetooth allowing the Bluetooth pairing request establishing the VPN connection entering the username and password Note The Bluetooth connection from the Nokia Wireless app towards the Nokia FastMile 4G Receiver is closed after one hour of inactivity in order to preserve Nokia Wireless phone resources. There is a mechanism in place that enables the user to re-establish the Bluetooth connection when he or she re-enters the app. Procedure 5 To perform management activities Use the following procedure to perform management activities through the Nokia Wireless app for a Nokia FastMile 4G Receiver that is managed remotely by the Nokia Altiplano FastMile Controller through NETCONF. 1 When you are close to the Nokia FastMile 4G Receiver, connect the mobile phone to the Internet and open the Nokia Wireless app on the phone. An introductory screen with a video appears. Figure 22 shows the introductory screen. 86 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 22 Introductory screen for unit managed by the Nokia Altiplano FastMile Controller through NETCONF Continue by tapping on Get started. 2 After the introductory screen has cleared, the Nokia Wireless app shows an animation of how to scan the QR code of the Nokia FastMile 4G Receiver so that the app can obtain the MAC address, unique device identifier, enterprise id, and device type of the Nokia FastMile 4G Receiver. The QR code was provided on a sheet of paper in the shipping package of the Nokia FastMile 4G Receiver. The sheet of paper, or a photograph of it, should have been saved and made available for anyone who later needs to scan the QR code when accessing the Nokia FastMile 4G Receiver. Figure 23 shows the screen for the prompt to scan the QR code. Issue: DRAFT 3TG-00386-ABGA-TCZZA 87 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 23 Screen with prompt to scan the QR code for unit managed by the Nokia Altiplano FastMile Controller through NETCONF Tap on Scan to start the scan of the QR code. Use the viewfinder of the phone to align with the QR code. Figure 24 shows the QR code screen. 88 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 24 QR code screen for unit managed by the Nokia Altiplano FastMile Controller through NETCONF 3 The Nokia Wireless app displays the screen to install the Nokia FastMile 4G Receiver. Tap on the Already Installed? option. Figure 25 shows the Already Installed option. Issue: DRAFT 3TG-00386-ABGA-TCZZA 89 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 25 Screen showing the Already Installed option for unit managed by the Nokia Altiplano FastMile Controller through NETCONF 4 The Nokia Wireless app prompts you to connect to the Nokia FastMile 4G Receiver. The connection will be done through Bluetooth in conjunction with a VPN. You will need to be close to the Nokia FastMile 4G Receiver and you will need to have Bluetooth enabled on the mobile phone and accept the pairing request when it appears. Figure 26 shows the screen to connect to the Nokia FastMile 4G Receiver. 90 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 26 Screen for connecting to the Nokia FastMile 4G Receiver Connect to the Nokia FastMile 4G Receiver by tapping on Connect. 5 The Nokia Wireless app prompts you to enable the VPN profile for a secure method to communicate with the Nokia FastMile 4G Receiver. Figure 27 shows the screen to enable the VPN profile. Issue: DRAFT 3TG-00386-ABGA-TCZZA 91 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 27 Screen for enabling the VPN profile Enable the VPN profile by tapping on Connect. 6 The android system of the mobile phone prompts you to accept the connection request. Figure 28 shows the prompt to accept the connection request. 92 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 28 Prompt for accepting the connection request Accept the connection request by tapping on OK. 7 The Nokia Wireless app prompts you to log in to the Nokia FastMile 4G Receiver. You will need to input the username and password for the Nokia FastMile 4G Receiver. Figure 29 shows the screen to log in to the Nokia FastMile 4G Receiver. Issue: DRAFT 3TG-00386-ABGA-TCZZA 93 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 29 Screen to log in to a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller Log in to the Nokia FastMile 4G Receiver by tapping on Log in. After you have logged in, you can:

view information for the Nokia FastMile 4G Receiver: see step 8 upload updated certificates to the Nokia FastMile 4G Receiver: see step 9 reboot the Nokia FastMile 4G Receiver: see step 10 change the configuration settings to the default factory load settings (Perform Factory Reset); see step 11 94 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app 8 You can view the following information for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller by selecting the Connection Status option of the main screen and scrolling through the screen by swiping up or down:

LTE cell info:

connection state: Does the Nokia FastMile 4G Receiver connect to this cell status: The current operational state of the PDN connection EARFCN: The carrier frequency in the uplink and downlink is designated by the E-UTRA. Absolute Radio Frequency Channel Number (EARFCN) in the range 0 - 65535. PCI: The physical cellid of cell Current signal stats:

RSRP: RSRP (Reference Signals Received Power) is a measurement of the received power level in an LTE cell network in dBm RSRQ: RSRQ (Reference Signals Received Quality) is a measurement of the received power quality in an LTE cell network in dB RSSI: RSSI (Received Signal Strength Indicator) is a measurement of the power present in a received radio signal by the Nokia FastMile 4G Receiver SINR: SINR (the Signal-to-Interference-plus-Noise ratio) is used in the LTE network from the Nokia FastMile 4G Receiver side to measure the quality of wireless connections in dB Average signal stats:

RSRP: average value of Reference Signal Received Power (dBm) in the measured RSRQ: average value of Reference Signal Received Quality (dB) in the measured RSSI: average value of Received Signal Strength indicator (dBm) in the measured interval, resolution 1dBm interval, resolution 1dB interval, resolution 1 SINR: average value of Signal-to-Interference-plus-Noise Ratio (dB) in the measured interval, resolution 1dB Other stats:

bytes sent: the total number of bytes sent on the interface bytes received: the total number of bytes received on the interface Figure 30 shows an example of the System state screen. Issue: DRAFT 3TG-00386-ABGA-TCZZA 95 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 30 System state screen example for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller Note The Nokia Wireless app will display a value of N/A for parameters that are not supported by the installed Home 4G Receiver Software version. The following additional Beam Angle information is displayed only for an ABA version as shown in Figure 31:

Antenna mode: wide or narrow Horizontal angle: the horizontal angle is expressed as a degree if the Antenna mode is narrow or as N/A if the antenna mode is wide 96 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 31 System state screen with Beam Angle information for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller 9 You can upload updated certificates (stored under downloads in the mobile phone's directory) to the Nokia FastMile 4G Receiver. i Tap on the Upload CA certificates option. Figure 32 shows the screen that has the Upload CA certificates option. Issue: DRAFT 3TG-00386-ABGA-TCZZA 97 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 32 Screen that has the Upload CA certificates option for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller ii Select the required CA certificates and tap on Ok. Note that the certificates must be in the download folder of the mobile phone before you can upload them to the Nokia FastMile 4G Receiver. Figure 33 shows the screen that lists the CA certificates. 98 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 33 Screen that lists the CA certificates for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller The following CA certificates are supported for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller:

pmaCA.pem (used for authenticating the Nokia Altiplano FastMile Controller) diagserverCA.pem (used for authenticating the optional diagnostics server) logserverCA.pem (used for authenticating the log server) swserverCA.pem (used for authenticating the software upgrade server) iii Figure 34 shows the screen that indicates that uploading of the CA certificates was successful. Issue: DRAFT 3TG-00386-ABGA-TCZZA 99 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 34 Screen indicating that uploading of the CA certificates was successful for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller Tap on Ok to clear the message. 10 You can reboot a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller through NETCONF by tapping on the Reboot Device option. Figure 35 shows the Reboot Device option. 100 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 35 Screen showing the Reboot Device option for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller The screen shows the reboot message indicating that the Bluetooth connection will be interrupted and that you will be disconnected. Figure 36 shows the screen that has the reboot message. Issue: DRAFT 3TG-00386-ABGA-TCZZA 101 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 36 Screen showing the reboot message for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller Press the Reboot option if you want to proceed with the reboot, or press the Cancel option. If you pressed the Reboot option, press OK. 11 You can change the configuration settings for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller through NETCONF to the default factory load settings by tapping on the Perform Factory Reset option. Figure 37 shows the Perform Factory Reset option. 102 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 37 Screen showing the Perform Factory Reset option for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller The screen shows the factory reset message indicating that the factory reset will reset the device back to factory settings and that all changes will be lost and that you will be disconnected. Figure 38 shows the screen that has the factory reset message. Issue: DRAFT 3TG-00386-ABGA-TCZZA 103 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 38 Screen showing the factory reset message for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller Press the Reset option if you want to proceed with the reset to factory settings, or press the Cancel option. If you pressed the Reset option, press OK. 13.3 Using the Nokia Wireless app to manage a unit managed by an ACS If an ACS is being used for remote management of the Nokia FastMile 4G Receiver

(through TR-069), you can use the Nokia Wireless app to perform management activities on the Nokia FastMile 4G Receiver after it has been installed, such as viewing information, uploading CA certificates, rebooting, or resetting to factory settings, as described in the following procedure. 104 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app This procedure does not involve use of the Nokia Altiplano FastMile Controller. You will need the QR code that was saved as described during installation of the Nokia FastMile 4G Receiver in order to scan it when logging in to the 4G Receiver through the Nokia Wireless app. Logging in to the Nokia FastMile 4G Receiver also includes the following:

initiating a Bluetooth connection enabling Bluetooth allowing the Bluetooth pairing request establishing the VPN connection entering the username and password Note The Bluetooth connection from the Nokia Wireless app towards the Nokia FastMile 4G Receiver is closed after one hour of inactivity in order to preserve Nokia Wireless phone resources. There is a mechanism in place that enables the user to re-establish the Bluetooth connection when he or she re-enters the app. Procedure 6 To perform management activities Use the following procedure to use the Nokia Wireless app to perform management activities for a Nokia FastMile 4G Receiver that is managed remotely by an ACS through TR-069. 1 When you are close to the Nokia FastMile 4G Receiver, connect the mobile phone to the Internet and open the Nokia Wireless app on the phone. An introductory screen with a video appears. Figure 39 shows the introductory screen. Issue: DRAFT 3TG-00386-ABGA-TCZZA 105 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 39 Introductory screen for unit managed by an ACS through TR-069 Continue by tapping on Get started. 2 After the introductory screen has cleared, the Nokia Wireless app shows an animation of how to scan the QR code of the Nokia FastMile 4G Receiver so that the app can obtain the MAC address, unique device identifier, enterprise id, and device type of the Nokia FastMile 4G Receiver. The QR code was provided on a sheet of paper in the shipping package of the Nokia FastMile 4G Receiver. The sheet of paper, or a photograph of it, should have been saved and made available for anyone who later needs to scan the QR code when accessing the Nokia FastMile 4G Receiver. Figure 40 shows the screen for the prompt to scan the QR code. 106 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 40 Screen with prompt to scan the QR code for unit managed by an ACS through TR-069 The Nokia Wireless app also provides a way to manually enter all the needed information in order to proceed with the installation without scanning a QR code. Tap on Scan to start the scan of the QR code. Use the viewfinder of the phone to align with the QR code. Figure 41 shows the QR code screen. Issue: DRAFT 3TG-00386-ABGA-TCZZA 107 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 41 QR code screen for unit managed by an ACS through TR-069 3 The Nokia Wireless app displays the screen to install the Nokia FastMile 4G Receiver. Tap on the Already Installed? option. Figure 42 shows the Already Installed option. 108 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 42 Screen showing the Already Installed option for unit managed by an ACS through TR-069 4 The Nokia Wireless app prompts you to connect to the Nokia FastMile 4G Receiver. The connection will be done through Bluetooth in conjunction with a VPN. You will need to be close to the Nokia FastMile 4G Receiver and you will need to have Bluetooth enabled on the mobile phone and accept the pairing request when it appears. Figure 43 shows the screen to connect to the Nokia FastMile 4G Receiver. Issue: DRAFT 3TG-00386-ABGA-TCZZA 109 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 43 Screen for connecting to the Nokia FastMile 4G Receiver Connect to the Nokia FastMile 4G Receiver by tapping on Connect. 5 The Nokia Wireless app prompts you to enable the VPN profile for a secure method to communicate with the Nokia FastMile 4G Receiver. Figure 44 shows the screen to enable the VPN profile. 110 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 44 Screen for enabling the VPN profile Enable the VPN profile by tapping on Connect. 6 The android system of the mobile phone prompts you to accept the connection request. Figure 45 shows the prompt to accept the connection request. Issue: DRAFT 3TG-00386-ABGA-TCZZA 111 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 45 Prompt for accepting the connection request Accept the connection request by tapping on OK. 7 The Nokia Wireless app prompts you to log in to the Nokia FastMile 4G Receiver. You will need to input the username and password for the Nokia FastMile 4G Receiver. Figure 46 shows the screen to log in to the Nokia FastMile 4G Receiver. 112 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 46 Screen to log in to a Nokia FastMile 4G Receiver managed by an ACS through TR-069 Log in to the Nokia FastMile 4G Receiver by tapping on Log in. After you have logged in, you can:

view information for the Nokia FastMile 4G Receiver: see step 8 upload updated certificates to the Nokia FastMile 4G Receiver: see step 9 reboot the Nokia FastMile 4G Receiver: see step 10 change the configuration settings to the default factory load settings (Perform Factory Reset); see step 11 Issue: DRAFT 3TG-00386-ABGA-TCZZA 113 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview 8 You can view the following information for a Nokia FastMile 4G Receiver managed by an ACS by selecting the Connection Status option of the main screen and scrolling through the screen by swiping up or down:

LTE cell info:

connection state: Does the Nokia FastMile 4G Receiver connect to this cell status: The current operational state of the PDN connection EARFCN: The carrier frequency in the uplink and downlink is designated by the E-UTRA. Absolute Radio Frequency Channel Number (EARFCN) in the range 0 - 65535. PCI: The physical cellid of cell Current signal stats:

RSRP: RSRP (Reference Signals Received Power) is a measurement of the received power level in an LTE cell network in dBm RSRQ: RSRQ (Reference Signals Received Quality) is a measurement of the received power quality in an LTE cell network expressed as a ratio RSSI: RSSI (Received Signal Strength Indicator) is a measurement of the power present in a received radio signal by the Nokia FastMile 4G Receiver in dBm SINR: SINR (the Signal-to-Interference-plus-Noise ratio) is used in the LTE network from the Nokia FastMile 4G Receiver side to measure the quality of wireless connections in dB Other stats:

bytes sent: the total number of bytes sent on the interface bytes received: the total number of bytes received on the interface Figure 47 shows an example of the System state screen. 114 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 47 System state screen example for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 Note The Nokia Wireless app will display a value of N/A for parameters that are not supported by the installed Home 4G Receiver Software version. The following additional Beam Angle information is displayed only for an ABA version as shown in Figure 48:

Antenna mode: wide or narrow Horizontal angle: the horizontal angle is expressed as a degree if the Antenna mode is narrow or as N/A if the antenna mode is wide Issue: DRAFT 3TG-00386-ABGA-TCZZA 115 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 48 System state screen with Beam Angle information for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 116 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app 9 You can upload updated certificates (stored under downloads in the mobile phone's directory) to the Nokia FastMile 4G Receiver. i Tap on the Upload CA certificates option, as shown in Figure 49. Figure 49 Screen that has the Upload CA certificates option for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 ii Tap on Upload on the Upload CA Certificates screen, as shown in Figure 50. Issue: DRAFT 3TG-00386-ABGA-TCZZA 117 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 50 Upload CA Certificates screen for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 A list of CA certificates appears, as shown in Figure 51. 118 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 51 List of CA certificates displayed on the Upload CA Certificates screen for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 iii Select the required CA certificates and tap on Ok. Note that the certificates must be in the download folder of the mobile phone before you can upload them to the Nokia FastMile 4G Receiver. Issue: DRAFT 3TG-00386-ABGA-TCZZA 119 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview The following CA certificates are supported for a Nokia FastMile 4G Receiver Nokia FastMile 4G Receiver managed by an ACS:

logserverCA.pem (used for authenticating the log server) swserverCA.pem (used for authenticating the software upgrade server) pmaCA.pem (used for authenticating the Nokia Altiplano FastMile Controller) diagserverCA.pem (used for authenticating the optional diagnostics server) acsCA.pem (used for authenticating the ACS) iv The screen indicates when uploading of the CA certificates was successful, as shown in Figure 52. 120 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 52 Screen showing that upload of CA certificates was successful for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 10 You can reboot a Nokia FastMile 4G Receiver managed by an ACS through TR-069 by Tap on Ok to clear the message. tapping on the Reboot Device option. Figure 53 shows the Reboot Device option. Issue: DRAFT 3TG-00386-ABGA-TCZZA 121 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 53 Screen showing the Reboot Device option for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 When you reboot the Nokia FastMile 4G Receiver, the screen shows the reboot message indicating that the Bluetooth connection will be interrupted and that you will be disconnected. Press the Reboot option if you want to proceed with the reboot, or press the Cancel option. If you pressed the Reboot option, press OK. 11 You can change the configuration settings for a Nokia FastMile 4G Receiver managed by an ACS through TR-069 to the default factory load settings by tapping on the Perform Factory Reset option. Figure 54 shows the Perform Factory Reset option. 122 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 54 Screen showing the Perform Factory Reset option for a Nokia FastMile 4G Receiver managed by ACS through TR-069 The screen shows the factory reset message indicating that the factory reset will reset the device back to factory settings and that all changes will be lost and that you will be disconnected. Figure 55 shows the screen that has the factory reset message. Issue: DRAFT 3TG-00386-ABGA-TCZZA 123 Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 55 Screen showing the factory reset message for a Nokia FastMile 4G Receiver managed by ACS through TR-069 Press the Reset option if you want to proceed with the reset to factory settings, or press the Cancel option. If you pressed the Reset option, press OK. 124 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI 14 Management using the Web UI 14.1 Using the Web UI to manage the Nokia FastMile 4G Receiver 14.2 Using the Web UI status screen 14.3 Using the Web UI network screen 14.4 Using the Web UI CBRS screen 14.5 Using the Web UI system screen 14.1 Using the Web UI to manage the Nokia FastMile 4G Receiver After the Nokia FastMile 4G Receiver has been installed, you can use the Web UI to perform some management-type activities on a Nokia FastMile 4G Receiver that is managed by an ACS through TR-069. See section 6.1.2 for more information about the Web UI. The Web UI provides the following screens to provide support for management of the Nokia FastMile 4G Receiver:

Status screen: allows viewing of FastMile 4G Receiver status parameter values, see section 14.2 Network screen: allows configuration of specific FastMile 4G Receiver parameters (login is required), see section 14.3 CBRS screen: offers the possibility to display CBSD parameters of the FastMile 4G Receiver, as well as to input registration information for CPI's usage (login is required), see section 14.4 System screen: allows performing of advanced system actions (login is required), see section 14.5 14.2 Using the Web UI status screen The Web UI status screen allows you to view FastMile 4G Receiver status parameters. No login is required. The following parameters are shown:

The Cell ID for primary attached cell The primary attached cell physical cell ID (PCI), eNodeB ID (eNBID), DL EARFCN and the Band Issue: DRAFT 3TG-00386-ABGA-TCZZA 125 Management using the Web UI Nokia FastMile 4G Receiver Product Overview The secondary attached cells physical cell ID (PCI) and DL EARFCN Secondary Component Carrier Band (Downlink) Secondary Component Carrier Band (Uplink) The Signal Strength of the attached cell: this animated model shows the RSRP

(Reference Signals Received Power) of the attached cell The RSRP (Reference Signals Received Power) of the attached primary and The RSRQ (Reference Signal Received Quality) of the attached primary and The RSSI (Received Signal Strength Indication) of the attached primary and The CINR (Carrier to Interference plus Noise Ratio) of the attached primary and The SINR (Signal to Interference and Noise Ratio) of the attached primary cell Total number of MB sent on the LTE interface since last FastMile 4G Receiver Total number of MB received on the LTE interface since last FastMile 4G Total number of MB sent on the Ethernet interface since last FastMile 4G Total number of MB received on the Ethernet interface since last FastMile 4G secondary cells secondary cells secondary cells secondary cells restart Receiver restart Receiver restart Receiver restart Data Model (TR-069) Software Version Name and corresponding IP address of the configured Access Points Device Info table with information regarding the IMSI, IMEI, Ethernet MAC Address, Serial Number and the Model Name You can display available cell information by triggering measurements using the Trigger measurement button on the Web UI status screen. Available cell information includes: physical cell ID, DL EARFCN, SINR, RSRP, RSRQ, RSSI. Note the following up to 12 available cells are shown, ranked from strongest to weakest by RSRP After approximately five seconds from triggering of measurements, the FastMile 4G Receiver will detach from the carriers network. Push the measurements status refresh button while the FastMile 4G Receiver is detached to see the grayed-out Web UI status screen. Reattachment of the FastMile 4G Receiver may take from several seconds to up to five minutes. You will need to refresh the browser for updated Web UI status screen contents after reattachment of the FastMile 4G Receiver. available cell information will not be visible after rebooting the FastMile 4G Receiver Figure 56 shows an example of the top part of the Status screen when the FastMile 4G Receiver is not connected to a cell. 126 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 56 Example of the top part of the Status screen when the FastMile 4G Receiver is not connected to a cell Figure 57 shows the lower part after scrolling down of an example of the Status screen without available cells when the FastMile 4G Receiver is not connected to a cell. Figure 57 Example of the lower part of the Status screen without available cells when the FastMile 4G Receiver is not connected to a cell Figure 58 shows the lower part after scrolling down of an example of the Status screen with available cells when the FastMile 4G Receiver is not connected to a cell. Issue: DRAFT 3TG-00386-ABGA-TCZZA 127 Management using the Web UI Nokia FastMile 4G Receiver Product Overview Figure 58 Example of the lower part of the Status screen with available cells when the FastMile 4G Receiver is not connected to a cell Figure 59 shows the top part of an example of the Status screen when the FastMile 4G Receiver is connected to a cell. Figure 59 Example of the top part of the Status screen when the FastMile 4G Receiver is connected to a cell Figure 60 shows a lower part after scrolling down of an example of the Status screen when the FastMile 4G Receiver is connected to a cell. The figure shows the trigger measurement button that can be used to display information about available cells. 128 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 60 Example of a lower part of the Status screen when the FastMile 4G Receiver is connected to a cell To display available cell information, select the trigger measurement button on the Status screen. Figure 61 shows the pop up window that appears when the trigger measurement button is selected. Figure 61 Example of the Trigger Measurement pop up window You can proceed or cancel the trigger measurement action. Note After approximately five seconds from triggering of measurements, the FastMile 4G Receiver will detach from the carriers network. Push the measurements status refresh button while the FastMile 4G Receiver is detached to see the grayed-out Web UI status screen. Reattachment of the FastMile 4G Receiver may take from several seconds to up to five minutes. You will need to refresh the browser for updated Web UI status screen contents after reattachment of the FastMile 4G Receiver. Issue: DRAFT 3TG-00386-ABGA-TCZZA 129 Management using the Web UI Nokia FastMile 4G Receiver Product Overview The following figures show examples of screens involved in the trigger measurement action:

Figure 62 shows trigger measurement that is ongoing Figure 63 shows trigger measurement that has completed with a list of available cells and the FastMile 4G Receiver is detached from the carrier's network Figure 64 shows trigger measurement that has completed and the FastMile 4G Receiver is reattached to the carrier's network Figure 62 Example of ongoing Trigger Measurement Figure 63 Example of Trigger Measurement completed and FastMile 4G Receiver is detached 130 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 64 Example of Trigger Measurement completed and FastMile 4G Receiver is reattached Figure 65 shows the lowest part after scrolling down of an example of the Status screen when the FastMile 4G Receiver is connected to a cell. Figure 65 Example of the lowest part of the Status screen when the FastMile 4G Receiver is connected to a cell 14.3 Using the Web UI network screen The Web UI network screen allows you to perform FastMile4G Receiver configuration actions. Login is required. For details on the Web UI login, please refer to the Customer Release Notes. The following configuration capabilities are supported:

Configuration of ACS URL Configuration of ACS username Configuration of ACS password Configuration of Connection Request Port Configuration of Connection Request Username Issue: DRAFT 3TG-00386-ABGA-TCZZA 131 Management using the Web UI Nokia FastMile 4G Receiver Product Overview Configuration of Connection Request Password Configuration of Periodic Inform Interval Configuration of Periodic Inform Request Setting of location; that is, geocoordinates (latitude and longitude) Configuration of Access Points (up to one default AP in router mode and up to four APs in bridge mode; a total of five APs can be configured). AP configuration includes configuration of:

forwarding mode (router or bridge) AP name Username Password Authentication mode VLAN MTU size Note that the default AP cannot be deleted subnet mask Configuration of cell list (up to nine cells can be configured) Configuration of the DHCP server for router mode Uploading of CA certificates Note CA certificates must be pre-downloaded to the laptop so that they can be browsed and found via the 'Upload Certificate' action. The CA Certificates must comply to the naming rules required by the FastMile4G Receiver. The following CA certificates are supported:

logserverCA.pem (used for authenticating the log server) swserverCA.pem (used for authenticating the software upgrade server) diagserverCA.pem (used for authenticating the optional diagnostics server) acsCA.pem (used for authenticating the ACS) Figure 66 shows an example of the Login screen. 132 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 66 Example of the Login screen Figure 67 shows an example of the Network screen. Issue: DRAFT 3TG-00386-ABGA-TCZZA 133 Management using the Web UI Nokia FastMile 4G Receiver Product Overview Figure 67 Example of the Network screen Figure 68 shows an example of scroll down for the Network screen. Figure 68 Example of scroll down for the Network screen Figure 69 shows an example of the Add Access Point window. 134 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 69 Example of the Add Access Point window Figure 70 shows an example of the Delete Access Point window Issue: DRAFT 3TG-00386-ABGA-TCZZA 135 Management using the Web UI Nokia FastMile 4G Receiver Product Overview Figure 70 Example of the Delete Access Point window Figure 71 shows an example of the Edit Location window. 136 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 71 Example of the Edit Location window Figure 72 shows an example of the Edit Controller window. Issue: DRAFT 3TG-00386-ABGA-TCZZA 137 Management using the Web UI Nokia FastMile 4G Receiver Product Overview Figure 72 Example of the Edit Controller window Figure 73 shows an example of the Edit Connection Request window. 138 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 73 Example of the Edit Connection Request window Figure 74 shows an example of the Edit DHCP window. Issue: DRAFT 3TG-00386-ABGA-TCZZA 139 Management using the Web UI Nokia FastMile 4G Receiver Product Overview Figure 74 Example of the Edit DHCP window Figure 75 shows an example of the Certificates information window that opens when you click on Upload Certificate. 140 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 75 Example of the Certificates information window Figure 76 shows an example of the Add Cell window. Figure 76 Example of the Add Cell window Figure 77 shows an example of the Delete Cell window. Issue: DRAFT 3TG-00386-ABGA-TCZZA 141 Management using the Web UI Nokia FastMile 4G Receiver Product Overview Figure 77 Example of the Delete Cell window 14.4 Using the Web UI CBRS screen The Web UI CBRS (Citizens Broadband Radio Service) screen is intended for the US market and offers the possibility to display CBSD (Citizens Broadband Radio Service Device) parameters of the FastMile 4G Receiver, as well as to input registration information for CPI's (Certified Professional Installer) usage. Login is required. For details on the Web UI login, please refer to the Customer Release Notes. The Web UI CBRS screen allows you to view the following FastMile 4G Receiver CBSD parameters:

FCC (Federal Communications Commission) ID CBSD (Citizens Broadband Radio Service Device) Category Air interface Measurement Capability Additionally, the Web UI CBRS screen allows you to input the following parameters:

User ID CRL (Certificate Revocation List) file CRL (Certificate Revocation List) URL SAS Server URL Figure 78 shows an example of the Web UI CBRS screen. 142 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 78 Example of the Web UI CBRS screen 14.5 Using the Web UI system screen The Web UI system screen allows you to perform advanced system actions on the FastMile 4G Receiver. Login is required. For details on the Web UI login, please refer to the Customer Release Notes. The following advanced system capabilities are supported:

Restart device: the FastMile 4G Receiver configuration remains intact Restore factory settings: factory configuration of the FastMile 4G Receiver is used; subsequent configuration is lost Update firmware:

before doing any firmware update action, make sure that the update path from the existing firmware to new firmware is supported by the FastMile 4G Receiver new image is installed in the FastMile 4G Receiver; the FastMile 4G Receiver configuration remains intact Enable/disable LAN SSH access (by default LAN SSH access is enabled) Enable/disable WAN SSH access (by default WAN SSH access is disabled) Figure 79 shows an example of the System screen. Issue: DRAFT 3TG-00386-ABGA-TCZZA 143 Management using the Web UI Nokia FastMile 4G Receiver Product Overview Figure 79 Example of the System screen Figure 80 shows an example of the Restart Device confirmation window. 144 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 80 Example of the Restart Device confirmation window Figure 81 shows an example of the Restore Device confirmation window used to restore the device to factory settings. Issue: DRAFT 3TG-00386-ABGA-TCZZA 145 Management using the Web UI Nokia FastMile 4G Receiver Product Overview Figure 81 Example of the Restore Device confirmation window Figure 82 shows an example of the screen that displays while firmware is being uploaded. 146 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 82 Example of the screen that displays while firmware is being uploaded Figure 83 shows an example of the screen that displays while firmware is being upgraded. Issue: DRAFT 3TG-00386-ABGA-TCZZA 147 Management using the Web UI Nokia FastMile 4G Receiver Product Overview Figure 83 Example of the screen that displays while firmware is being upgraded Figure 84 shows an example of the screen that displays while the system is being rebooted. 148 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 84 Example of the screen that displays while the system is being rebooted Issue: DRAFT 3TG-00386-ABGA-TCZZA 149 Management using the Web UI Nokia FastMile 4G Receiver Product Overview 150 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Standards certification 15 Standards certification 15.1 Standards certification for Compact mono-band and ABA models 15.2 Standards certification for the Compact multi-band models 15.1 Standards certification for Compact mono-band and ABA models Table 24 provides standards certification information for the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver. Table 24 Standards certifications for the Nokia FastMile 4G Receiver Compact mono-band and ABA models Category Certifications RF EMC EN 301 908-13 for Band 3, 7, 38, 40, 42, 43 of the Compact mono-band models and Band 42, 43 of the ABA model FCC 47 Parts 27 for Band 7 and 41 of the Compact mono-band models ISED for Band 42 and 43 of the ABA model ETSI EN 301 489-1 and -52 for Band 3, 7, 38, 40, 42, 43 of the Compact mono-band models and Band 42, 43 of the ABA model FCC 47 part 2/15 for Band 7 and 41 of the Compact mono-band models ISED for Band 42 and 43 of the ABA model RoHS Safety Directive 2011/65/EU EN/IEC 60950-1; 60950-22 UL 62368-1, UL 60950-22,UL 50E, EN/IEC 60529 (IP66) The CE mark is valid for Band 3, 7, 38, 40, 42, 43 of the Compact mono-band models and Band 42, 43 of the ABA models. The FCC ID is valid for Band 7 and 41 of the Compact mono-band models. See section 18.1 for the FCC ID for each model. The ISED ID is valid for Band 42 and 43 of the ABA model. See chapter 18 for FCC statements and label instructions. Issue: DRAFT 3TG-00386-ABGA-TCZZA 151 Standards certification Nokia FastMile 4G Receiver Product Overview 15.2 Standards certification for the Compact multi-band models Table 25 provides standards certification information for the Compact multi-band models of the Nokia FastMile 4G Receiver. Table 25 Standards certifications for the Nokia FastMile 4G Receiver Compact multi-band models Category Certifications RF EMC EN 301 908-13 for the following:

Band 1, 3, 7, 20, 28, 38, and 40 of the Compact multi-band 4G05-A and 4G05-B models Band 3, 7, 20, and 32 of the Compact multi-band 4G04-A model Band 1, 3, 7, 20, and 32 of the Compact multi-band 4G17-A model Band 7, 28, 42, and 43 of the Compact multi-band 4G06-A model FCC 47 Part 27 for Band 41 of the Compact multi-band 4G05-A and 4G05-B models and Band 2, 25,4, 66, and 7 of the Compact multi-band 4G06-A model ETSI EN 301 489-1 and -52 for the following:

Band 1, 3, 7, 20, 28, 38, and 40 of the Compact multi-band 4G05-A and 4G05-B models Band 3, 7, 20, and 32 of the Compact multi-band 4G04-A model Band 1, 3, 7, 20, and 32 of the Compact multi-band 4G17-A model Band 7, 28, 42, 43 of the Compact multi-band 4G06-A model FCC 47 part 2/15 for Band 41 of the Compact multi-band 4G05-A and 4G05-B models and Band 2, 25, 4, 66, 7 of the Compact multi-band 4G06-A model RoHS Safety Directive 2011/65/EU EN/IEC 60950-1; 60950-22 UL 62368-1, UL 60950-22,UL 50E, EN/IEC 60529 (IP66) The CE mark is valid for Band 1, 3, 7, 20, 28, 38, 40 of the Compact multi-band 4G05-A and 4G05-B models and Band 3, 7, 20, and 32 of the Compact multi-band 4G04-A model and Band 1, 3, 7, 20, and 32 of the Compact multi-band 4G17-A model and Band B7,28,42,43 of the Compact multi-band 4G06-A model. The FCC ID is valid for Band 41 of the Compact multi-band 4G05-A and 4G05-B models and Band 2, 25,4, 66, and 7 of the Compact multi-band 4G06-A model. See section 18.1 for the FCC ID for each model. See chapter 18 for FCC statements and label instructions. 152 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Appendix A: Specifications 16 Appendix A: Specifications 16.1 Specifications 16.1 Specifications Table 26 provides some specifications for the Nokia FastMile 4G Receiver. Table 26 Specifications for the Nokia FastMile 4G Receiver Item Dimensions Weight Power consumption Operating altitude Non-operating altitude Operating temperature Description Compact multi-band models: 22.7 cm by 22.7 cm by 6.4 cm

(8.94 in by 8.94 in by 2.52 in) Compact mono-band models: 23.5 cm by 23.5 cm by 5.2 cm

(9.3 in by 9.3 in by 2 in) ABA models: 31.8 cm by 31.8 cm by 5.6 cm (12.5 in by 12.5 in by 2.2 in) Compact multi-band models: 0.88 kg (1.9 lb) Compact mono-band models: 1.3 kg (2.9 lb) ABA models: 2 kg (4.4. lb) Idle: 1.6 W Maximum: 12 W Maximum operating altitude is 3048 m (10 000 ft) above mean sea level Maximum non-operating altitude is 12 192 m (40 000 ft) above mean sea level Compact mono-band and ABA models:

30C to 65C (22F to 149F) Compact multi-band models:

Model 4G05-B: 40C to 55C (40F to 131F) models other than Model 4G05-B: 30C to 55C (22F to 131F) Storage temperature 40C to 85C (85F to 185F) Humidity IP rating 5% to 95% non condensing IP66 TYPE3 Issue: DRAFT 3TG-00386-ABGA-TCZZA 153 Appendix A: Specifications Nokia FastMile 4G Receiver Product Overview 154 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Appendix B: RF exposure 17 Appendix B: RF exposure 17.1 RF exposure 17.1 RF exposure The international standards used for the assessment of this device provide simple conformity assessment methods for low power electronic and electrical equipment to an exposure limit relevant to electromagnetic fields (EMF). Table 27 indicates RF exposure distances for each model for:

CE based on the compliance criteria for maximum permissible exposure as in CE Council Recommendation Directive 2014/53/EU FCC based on the compliance criteria for maximum permissible exposure as in FCC 47 Table 27 RF exposure distances Model 4G01-A 4G01-B 4G02-A 4G03-A 4G04-A 4G05-A 4G05-B 4G06-A 4G17-A RF exposure distance CE FCC 50 cm (19.69 in) 20 cm (7.87 in) 50 cm (19.69 in) 50 cm (19.69 in) 50 cm (19.69 in) N/A 50 cm (19.69 in) 50 cm (19.69 in) 20 cm (7.87 in) 20 cm (7.87 in) 20 cm (7.87 in) 20 cm (7.87 in) N/A N/A 20 cm (7.87 in) 23 cm (9.06 in) 20 cm (7.87 in) N/A Issue: DRAFT 3TG-00386-ABGA-TCZZA 155 Appendix B: RF exposure Nokia FastMile 4G Receiver Product Overview 156 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Appendix C: FCC statements and label instructions 18 Appendix C: FCC statements and label instructions 18.1 FCC compliance statement 18.2 FCC radiation exposure statement 18.3 FCC label instructions 18.1 FCC compliance statement Table 28 provides the FCC ID for the Nokia FastMile 4G Receiver. Table 28 FCC ID for Nokia FastMile 4G Receiver Model 4G01-A 4G01-B 4G02-A 4G03-A 4G05-A 4G05-B 4G06-A 4G17-A FCC ID 2ADZR34003800FM20 2ADZR34003800FM201 Not applicable 2ADZR23002690FM20 2ADZR4G05A Not applicable 2ADZR4G06A Not applicable Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and 2) This device must accept any interference received, including Interference that may cause undesired operation. Issue: DRAFT 3TG-00386-ABGA-TCZZA 157 Appendix C: FCC statements and label instructions Nokia FastMile 4G Receiver Product Overview 18.2 FCC radiation exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distances indicated in chapter 17 between the radiator and your body. 18.3 FCC label instructions The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as:

Contains Transmitter Module FCC ID: 2ADZR4G04A and 2ADZR4G05A. Any similar wording that expresses the same meaning may be used. 158 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Glossary 19 Glossary This glossary provides the expansions and optional descriptions of most acronyms and initialisms that appear in this document. 3rd Generation Partnership Project Automated Beam Alignment Auto Configuration Server American National Standards Institute Access Point Access Point Name Certificate Authority or Carrier Aggregation Citizens Band Radio Service China Restriction of Hazardous Substances Downlink Differentiated Services Code Point Device Unique Identifier External Call Interface Evolved Packet Core Electronic Information Products Electromagnetic Compatibility Electromagnetic Interference Evolved Packet Core Electrostatic Discharge Electrotechnical Laboratory European Telecommunications Standards Institute Federal Communications Commission Frequency Division Duplex EARFCN E-UTRA Absolute Radio Frequency Channel Number E-UTRA Evolved Universal Terrestrial Radio Access 3GPP ABA ACS ANSI AP APN CA CBRS CRoHS DL DSCP DUID ECI EPC EIP EMC EMI EPC ESD ETL ETSI FCC FDD Issue: DRAFT 3TG-00386-ABGA-TCZZA 159 Glossary Nokia FastMile 4G Receiver Product Overview Maximum Concentration Value or Minimum Concentration Value FM HSS IEEE IP IPTV LAN LED LTE MAC MCV MIMO MME NAC NEC OAM PCI PCRF PDF PIN PoE QCI QoS QR RF RoHS RSRP RSRQ RSSI FastMile Home Subscriber Server Institute of Electrical and Electronics Engineers International Protection or Internet Protocol Internet Protocol over Television Local Area Network Light Emitting Diode Long-Term Evolution Media Access Control Multiple-Input Multiple-Output Mobility Management Entity Network Access Control National Electrical Code Operations and Maintenance Physical Cell Identifier Policy and Charging Rules Function Portable Document Format Personal Identification Number Power over Ethernet QoS Class Identifier Quality of Service Quick Response Radio Frequency Restriction of Hazardous Substances Reference Signal Received Power Reference Signal Received Quality Received Signal Strength Indicator 160 3TG-00386-ABGA-TCZZA Issue: DRAFT Nokia FastMile 4G Receiver Product Overview Glossary SIM SINR TCP TDD UDP UL URL VDC VoIP VPN WiFi ZIP Subscriber Identify Module Signal-to-Interference-plus-Noise Ratio Transmission Control Protocol Time Division Duplex User Datagram Protocol Underwriters Laboratories Uplink Uniform Resource Locater Volts Direct Current Voice over Internet Protocol Virtual Private Network Wireless Fidelity Compressed File Issue: DRAFT 3TG-00386-ABGA-TCZZA 161 Glossary Nokia FastMile 4G Receiver Product Overview 162 3TG-00386-ABGA-TCZZA Issue: DRAFT Customer document and product support Customer documentation Customer Documentation Welcome Page Technical Support Customer Documentation Technical Support Documentation feedback Customer Documentation Feedback Copyright 2020 Nokia. 3TG-00386-ABGA-TCZZA

NOKIA FastMile Receiver PUI ATTA Model: 4G06-A P/N: 3TGOO171ABAA I de in Chi ree encore an UIA DTT AN ICS:XX MRev:XX MFG Year:XX Wk:XX S/N: XXXXXXXXXXXXX IMEI:

geen en PUVA NAVAN C Dx FE i. MAC: XXXXXXXXXXX LISTED 5012307

Nokia Shanghai Bell Co. Ltd. No. 388, Ningqiao Rd.Pilot Free Trade Zone,Shanghai,China Tel: 86-21-38439795 Fax: 86-21-38430001-1119 Date: March 4, 2020 Power of Attorney To whom it may concern, Please be notified that I, Yong Tu , have designated Michael Lin in Sporton International Inc. as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Michael Lin in Sporton International Inc., on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This authorization is limited to the product of as following:

FCC ID: 2ADZR4G06A If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, fou Contact Person: Yong Tu Company: Nokia Shanghai Bell Co. Ltd. TEL: 86-21-38439795 FAX: 86-21-38430001-1119 E-mail: yong.tu@nokia-sbell.com