FCC ID: EF400178 Alarm Control Panel

10013635A LTE-CELL-MODULE-INSTALL-INSTR-en-PRT, 09/16/2016, BLACK, 20LB MEAD BOND, 8.5X11, TOL. +/- 0.125, SCALE: 1:1, FRONT & BACK, FOLD TO FIT BOX PRINTERS INSTRUCTIONS LTE CELL RADIO MODULE INSTALLATION INSTRUCTIONS The 2GIG LTE Cell Radio Module is a snap-in, cellular radio module that provides the 2GIG Control Panel with the ability to send and receive two (2) -way voice communications with the Central Station monitoring the security system. It is designed for use with two (2) External Cellular Antennas which provides a consistently strong signal for communications. NOTE: For best performance locate the antenna away from metal. In addition to providing the Control Panel the ability to transmit security information to online monitoring portals, the cell radio module allows for delivery of Over-the-Air (OTA) rmware updates to the Control Panel. Box Contents Verify that the package includes the following items:

1LTE Cell Radio Module 2External Cellular Antennas 2#4 Phillips Head Machine Screws and Lock Washers NOTE: Both antennas must be installed for proper performance. Connect one antenna to the MAIN connector and place the antenna outside the case as shown in Figure 2. Connect the other antenna to the DIV connector and place it inside the case. NOTE: Route the antenna cables so that they do not run across the top of the module. 8 Pull the loose end of the antenna through the access hole on the Control Panels backplate. Figure 2 Antenna Placement Requirements 2GIG Control Panel with the appropriate rmware version for your Cell Radio Module Installing the LTE Cell Radio Module and Antennas NOTE: As with all electrical appliances, a shock hazard exists if any electrical current is connected to the 2GIG Control Panel by AC power or battery while inserting, removing, or replacing parts. To install the Cell Radio Module:

1 Disconnect the AC power supply from its power source. 2 Remove the backplate from the Control Panel. 3 Disconnect the battery from the Control Panel. 4 Align the Cell Radio Module as shown in the gure below. 5 Use the two (2) screws and lock washers provided to secure the Cell Radio Module as shown in the gure below. Figure 1 LTE Cell Radio Module Placement 9 Replace the Control Panels backplate. Removing an Existing Cell Radio Module and Antenna If you are replacing an existing module with a new LTE Cell Radio Module, use the steps below. NOTE: As with all electrical appliances, a shock hazard exists if any electrical current is connected to the 2GIG Control Panel by AC power or battery while inserting, removing, or replacing parts. Removing the Cell Radio Module To remove the Cell Radio Module:

1 Disconnect the AC power supply from its power source. 2 Remove the backplate from the Control Panel. 3 Disconnect the battery from the Control Panel. 4 Detach the antennas as shown in 1 in the gure below. For steps, see "Removing an Internal Antenna" on page 2 or

"Removing an External Antenna" on page 2. 5 Remove the screws as shown in 2 in the gure below. 6 Pull the Cell Radio Module out carefully, without bending the pins as shown in 3 in the gure below. A = MAIN connector for out-of-panel antenna (in wall or in desk mount) B = DIV connector for in-panel antenna 6 Attach the provided FCC Label to the control panel back cover. 7 Ax both antenna cables to the connectors on top of the Cell Radio Module as follows:

Copyright 2016 Nortek Security & Control LLC 1 Figure 3 Removing the Cell Radio Module 7 Plug the new Cell Radio Module into the 2GIG Control Panel by carefully placing it onto the pins. Secure the module with the two (2) Phillips Head Machine Screws and Lock Washers. 8 9 Attach both of the new antennas as described in "Installing the LTE Cell Radio Module and Antennas" on page 1. 10 Replace the previous FCC label with the new FCC label on the control panel back cover. NOTE: If replacing a 3G or CDMA radio, do not reuse the existing antenna. Removing an Internal Antenna To remove an internal antenna:

1 Disconnect AC power supply from power source. 2 Disconnect the battery from the 2GIG Control Panel. 3 4 Detach the antenna. 5 Pull the internal antenna out from the side of the 2GIG Control Lift up the side ap on the 2GIG Control Panel. Panel. Removing an External Antenna To remove an external antenna:

1 Disconnect AC power supply from power source. 2 Remove the backplate from the Control Panel. 3 Disconnect the battery from the 2GIG Control Panel. 4 Detach the antenna. 5 Pull the external antenna from where it was previously installed. 6 Replace the back cover on the control panel. Regulatory Information Regulatory marks are axed to either the LTE Cell Radio Module and/

or its packaging. For regulatory information, submit an email request to: 2gigtechsupport@nortek.com Limited Warranty This Nortek Security & Control product is warranted against defects in material and workmanship for one (1) year. This warranty extends only to wholesale customers who buy direct from Nortek Security & Control LLC or through Nortek Security & Control LLCs normal distribution channels. Nortek Security & Control LLC does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealers warranty, if any. There are no obligations or liabilities on the part of Nortek Security &

Control LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or prot, or cost of removal, installation, or reinstallation. All implied warranties for functionality, are valid only until the warranty expires. This Nortek Security &

Control LLC Warranty is in lieu of all other warranties expressed or implied. For technical support in the USA and Canada:

855-2GIG-TECH (855-244-4832) Email: 2gigtechsupport@nortek.com Visit website for technical support hours of operation For technical support outside of the USA and Canada:

Contact your regional distributor Visit 2gig.com/dealers/ for a list of distributors in your region PN: 10013635A 2 Copyright 2016 Nortek Security & Control LLC

2GIG GC2E Security & Automation SystemRegulatory StatementsThe GC2E Security & Automation System (2GIG-GC2E) is marked to indicate its compliance with: United StatesFederal Communications Commission (FCC) CanadaIndustry Canada (IC)Please read the appropriate section that corresponds to the marking on the product before attempting to install the product.United StateS, FCC StatementSCanada, indUStry Canada StatementSnorth ameriCan SaFety StandardSinqUirieSWireless Product NoticeRadio controls provide a reliable communication link and fill an important need in portable wireless signaling; however, there are some limitations which must be observed. For United States installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range (approximately 400 feet (121.92 meters)). A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. Changes or modifications to the device may void FCC compliance. Infrequently used radio links should be tested regularly to protect against undetected interference or fault. A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the end users.FCC Part 15: Class B Digital Device StatementFCC ID: EF400178IC: 1078A-00178This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept interference received, including interference that maycause undesired operation.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one (1) or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. NOTE: Any changes or modifications made to this device that are not approved by 2GIG may void the authority granted to the user by the FCC to operate this equipment.ICES-003 Class B NoticeThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada.Industry Canada (IC) Compliance NoticeThis device complies with Industry Canada license-exempt Radio Standard Specifications (RSS). Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept interference received, including interference that maycause undesired operation.Avis de Conformit dIndustrie Canada (IC)Le prsent appareil est conforme aux les Cahiers des charges sur les Normes Radiolectriques (CNR) dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:1. lappareil ne doit pas produire de brouillage, et2. lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.The GC2E Security & Automation System is ETL Listed in North America and when installed and configured as described in the GC2E Security & Automation System Installation Guide, meets the standards for: UL 985: Household Fire Warning System Units and CAN/ULCS545:Residential Fire Warning System Control Units UL 1023: Household Burglar Alarm Units and CAN/ULC1023: Household Burglar Alarm System Units UL 1610: Central-Station Burglar-Alarm Units ANSI/SIA CP-01-2010: Control Panel Standard - Features for False Alarm ReductionDirect all inquiries regarding this regulatory compliance statement to:Nortek Security &Control LLC5919 Sea Otter Place, Suite 100Carlsbad, CA92010USA800-421-1587 P/N: 10022257 APRINTERS INSTRUCTIONSREGULATORY INSERT, GC2E PANEL- P/N: 10022257 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.5X11, TOL. +/- 0.125, SCALE: 1:1, FRONT & BACK, FOLD ONCE TO 5.5 x 8.5

FILE: 10022313 X4 - GUIDE,USER,GO!CONTROL2.5 - INK: BLACK - MATERIAL: 20 LB MEAD BOND WITH 80 LB COATED COVER- SIZE: 5.5 x 8.5 INCH VERTICAL - SCALING 1-1 - FOLDING: ALBUM FOLD -

PRINTERS INSTRUCTIONS:

BINDING: SADDLE-STICH GC2.5 Panel User Guide ENGLISH

(International) WIRELESS SECURITY SYSTEM WARNING: OWNERS INSTRUCTION NOTICE Not to be removed by anyone except occupant TABLE OF CONTENTS SYSTEM OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Sensor Types/Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Smoke, Heat, and Freeze Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Burglary Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 User Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Trouble Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Wireless Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CONTROL PANEL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 MAIN DISPLAY SCREENS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Home Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Security Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Ready to Arm Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Menu Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 BURGLARY PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 SAMPLE FLOOR PLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 SENSOR STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 CHECKING FOR CLOSED SENSORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 VIEWING EACH SENSORS STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 DEALING WITH A SENSOR FALSE ALARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 SENSOR BYPASSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Force Bypass All Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Bypassing/Un-Bypassing Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 STAY MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Entry Delay in Stay Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Quick Exit in Stay Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 SILENT CONTROL IN STAY MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Arming to Stay Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 AWAY MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Exit and Entry Delays in Away Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Exit Delay Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Silent Control in Away Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Quick Exit in Away Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Auto Stay Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Arming to Away Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 DISARMING THE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Disarming from Stay Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Disarming from Away Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 IF A BURGLARY ALARM OCCURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Burglary Alarm Siren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Alarm Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Optional 2-Way Voice Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 KEY FOB: ARMING AND DISARMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Arm with a Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Away Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Disarm with a Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Activate the Emergency Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Activate the Auxiliary Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 1 Copyright 2018 Nortek Security & Control WIRELESS KEYPAD: ARMING AND DISARMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Arm with a Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Away Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Disarm with a Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Activate a Fire Emergency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Activate a Police Emergency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 SMOKE, HEAT AND FREEZE PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Initiating a Fire Alarm Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 If the Fire Alarm Sounds Automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Silencing a False Fire Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 RECOMMENDED FIRE ALARM LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 NFPA Standard #72 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Do Not Mount a Smoke Alarm Here . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Emergency Action Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 EMERGENCY FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 24-HOUR EMERGENCY BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Panic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Emergency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 SYSTEM TROUBLE ALERTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 TROUBLE ALERT ICON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 VIEW THE CURRENT TROUBLE ALERTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 TROUBLE ALERT BEEP HOLD-OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 SYSTEM STATUS ICONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 AC POWER ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 TEST MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 AC POWER OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 TOUCH SCREEN KEYPAD TRAFFIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 SOUNDER DISABLED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 CELL RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 LOW BACKUP BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 INTERIOR SENSOR OPEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 MESSAGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 DISPLAYING MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 READING MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 READING CONFIDENTIAL MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 FILTERING MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 SORTING MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 SYSTEM TOOLBOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 USER MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 User Code Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Adding a User Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 User Code Validity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 User Code Access Schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Adding/Editing User Access Schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Recurring User Access Schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Date User Access Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Date Range User Access Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Deleting User Access Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 User Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Deleting a User Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Duress User Code Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Setting the Duress User Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2 Copyright 2018 Nortek Security & Control Secret Duress Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 SYSTEM HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 SYSTEM TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Sensor Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Panel Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 CHIME SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 ADJUSTING THE BRIGHTNESS/VOLUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 ADJUSTING THE BACKLIGHT TIMEOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 CLEANING THE TOUCH SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 SET DATE AND TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 DISPLAY FIRMWARE VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 DEALER INFO SCREEN AND CALL BACK BUTTON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Accessing the Dealer Info Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Requesting a Service Call Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 INSTALLER PROGRAMMED OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Siren Run Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Sensor Trigger Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Fire Horn Run Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Exit Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Entry Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 24-Hour Emergency Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Quick Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Quick Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Quick Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Auto Un-bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Auto Stay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Key Fob Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Key Fob Disarm After Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Key Fob Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Wireless Keypad Emergency Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Exit Delay Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Cancel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Cancel Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Dialer Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 2-Way Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 INSTALLER SPECIFIC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 User Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 SERVICE INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 REGULATORY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Wireless Product Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 FCC Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 IMPORTANT NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 ALARM SYSTEM LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Panel Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 3 Copyright 2018 Nortek Security & Control SYSTEM OVERVIEW This system provides three (3) forms of protection: burglary, fire, and emergency, depending on the options set by your installer. The system consists of a Control Panel with a color touch screen, wireless sensors that provide perimeter and interior burglary protection, and wireless smoke and carbon monoxide detectors. In addition, optional remote control key fobs, wireless panic buttons and keypads may have been provided or installed. The system monitors all protection zones and the systems status. The Control Panel displays monitoring information and controls the alarm siren. Your system may have also been setup to send alarm and status reports to a Central Station and may have the capability for 2-way voice communications with the alarm monitoring operator. FEATURES The following is a list of standard features and options that can be included in your system. Ask your installer which options are available, and check the boxes that apply. Stay and Away arming modes: Stay mode arms the system perimeter only and is used typically at night when the premises are occupied. Away mode arms the system perimeter and interior; it is used when the premises are unoccupied. 60 user-unique 4-digit codes to operate the system: The system supports one (1) master user code that can assign and maintain the other user codes. One of the 60 user codes functions as a duress code. Controlling the system with this code gives the appearance of normal operation, but using it sends a silent duress report to the Central Station to initiate a silent alarm call for help. Voice announcements from the Control Panel: The system has a vocabulary of descriptive words that can be assigned to sensors so each has a unique announcement such as front door or bedroom window if desired. Home automation with the built-in Z-Wave controller for remote control of Z-Wave enabled home appliances (optional feature). Alarm history with system event log: Each alarm and system alert is logged into the systems memory. These events can be displayed and reviewed at the Control Panel or reviewed remotely by the Central Station. Real-time clock and calendar appears on the systems display and is used to time stamp items in the event log. 2-way voice communication: After an alarm, the system can automatically connect with a Central Station operator to converse with people in the premises. Remote control of the system using a Web-enabled device through the Internet.*

Three optional 24-hour emergency functions: Panic, Fire, and Emergency. These functions can be activated by pressing buttons on the Control Panel, using wireless sensors, using the wireless keypad or using portable pendant devices (such as the panic button remote).

* Requires the optional Cellular Radio Module. 4 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide System Overview Messages Your security system supports receiving messages from the Central Station. The messages detail system upgrades, additional services, special regional weather alerts, etc. Trouble Alerts The system monitors itself for abnormal operating conditions and will alert you if trouble is detected. Trouble conditions can be reported to the Central Station. Wireless Sensors Your security system comes with wireless sensors. Some sensors are visible, but others may be hidden by door-

jambs or where the sensor is mounted. Depending on your type of installation and the amount of sensors installed with the Control Panel, sensors can include but are not limited to the following:

Door/Window Sensor Glass Break Sensor CO Sensor Key Fob Motion Detector Smoke/Heat/Freeze Alarm Panic Remote Button Wireless Touch Screen Keypad BASIC OPERATION The following are general operational concepts that your system supports. Understanding these concepts will help you to use your security system to its fullest extent. Sensor Types/Zones The systems wireless sensors have been assigned to selected types (often called zones). The sensor type determines how and when the system will react to a signal from the sensor. Some sensors are armed 24 hours a day. Other sensors are armed only when the system is armed. Smoke, Heat, and Freeze Protection If wireless smoke, heat, and freeze detectors have been installed in your system, they are armed 24 hours a day. They will sound an alarm when smoke is detected and can report the fire alarm to the Central Station. See Smoke, Heat and Freeze Protection on page 18 for emergency planning and evacuation information. Burglary Protection Burglary protection is provided by perimeter and interior sensors. When the system is armed in the Away mode, both perimeter and interior sensors are armed and can trigger an alarm. When the system is armed in the Stay mode, only the perimeter sensors are armed and can trigger an alarm. Both arming modes offer an Exit Delay that allows time to exit the premises without triggering the alarm. Upon re-entry, an Entry Delay is enabled that allows you time to disarm the system. You can set sensors to sound a chime and/or a voice announcement when they are triggered. This allows you to monitor your doors and windows while the system is disarmed. For more details, see Burglary Protection on page 8. User Codes The system installer has already programmed a master user code for your system. This code can be used to control the system as well as assign and change the other user codes. The master user code can also access several system setup settings in the User Toolbox. Alarms When an alarm occurs, the Control Panels siren and an external siren (if installed) sound for a preset period of time. During active alarms and after disarming, the alarm history button displays all the activated alarms and the sensors that were involved. The alarm history clears the next time the system is armed or can be cleared manually. 5 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide CONTROL PANEL FEATURES See the table below for full descriptions of Control Panel Features. System Overview A C B D E A Alarm Sounder and Speaker B Color Display with Touchscreen C Emergency Button/Indicator D Microphone E Home Button/Indicator Sounds all system local alarms, voice prompts, system sounds, and audio for two (2)-way voice communications with the Central Station Displays all system information, status, programming, and functions as the keypad. The display cycles clock, calendar, and weather with an Alarm.com account (tap manually to change) Illuminates WHITE when enabled for emergency alarms and flashes during emergency alarms Used for voice communication with the Central Station Sensor Status Illuminates BLUE when all sensors are closed (Ready to Arm) Not lit when any sensor is open (not Ready to Arm) Arming Status Illuminates RED when system is armed Flashes RED during the Entry Delay Alarm Memory Flashes RED during an alarm Flashes RED after an alarm while system is still armed Power Outage Flashes WHITE during power outage (system on battery backup) Flashes BLUE when all sensors are closed (Ready to Arm) Flashes ORANGE when any sensor is open (not Ready to Arm) Flashes RED while system is armed 6 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide MAIN DISPLAY SCREENS Use the touch screen to control and operate the Control Panel. The touch screen includes a variety of buttons, indicators, and text for navigation and system operation. At the top-left of the Home screen, you can view the current system state. Scrolling text shows any pending alerts. The right side of the screen reveals a variety of system status icons. Home Screen The Home screen shows system status with icons to indicate system conditions. It also displays the time and date. The Home screen has Security, Services, Silent Control and Display Off buttons. System Overview Ready to Arm Screen Use the Entry Delay screen to arm the security system in Stay and Away mode. You also have the option to select the Entry Delay and Silent Exit check boxes to turn those features ON. Menu Screen Use the Menu screen to gain access to the Entry Delay, Emergency, or Toolbox screen. TIP: Tap the Services button to access features for controlling Z-Wave devices. If Z-Wave features are not programmed, this button will not appear. button on the panel to reveal the Home Tap the Home screen. Security Screen Use the Security screen to access the Arm, Menu, and Status screens. This screen also shows the current time and date. If messages, alarms, or trouble alerts are pending, square buttons indicate the number of pending alarms or messages. Status Screen Use the controls in the Status screen to view the systems current status and to review a scrolling list of alerts in a log format. The date, time and nature of any alerts are listed in the displayed log. Tap the Silence button to stop the system status voice announcement. Tap the or arrows to scroll through the list status messages. 7 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide BURGLARY PROTECTION When your system was set up by your installer, wireless sensors were placed to monitor specific doors and windows. The installer selected these doors and windows as likely places where an unlawful intrusion may occur and be detected. Each sensor was programmed to have the system react in a specific way. See "Installer Programmed Options" on page 34 for specifics about each sensor. Some sensor types (such as smoke detectors, carbon monoxide detectors, panic buttons, etc.) are always active and can trigger an alarm at any time. Other sensors on protected doors and windows are part of the burglary protection part of the system that can be turned on or off. Turning on the burglary protection part of the security system is called Arming the System". The burglary protection part of the system can be armed in two modes: Stay mode or Away mode. SAMPLE FLOOR PLAN Refer to the floor plan below. It shows a typical residential installation and the various types of wireless sensors and their functions. Front and side door sensors have Exit/Entry Delay Side and main garage door sensors have Exit/Entry Delay Control panel A B CP DW Door/window sensor PIR Motion detector SMKE Smoke detector Carbon monoxide detector Glass break sensor CO GB PAD Wireless keypad ES External siren IMPORTANT: Security systems installed in a commercial location are for use only as a burglar alarm system and not for fire protection. This security system has been evaluated and complies with UL 1610. For commercial installations (UL 1610), only one method of communication is to be used. This method of communication is a Cell Radio Module. 8 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide Burglary Protection SENSOR STATUS The security system constantly monitors all of the sensors attached to the protected doors and windows in your home or business. The Control Panel knows if each door or window with sensors is open or closed. The open or closed condition of the protected doors and windows is called the sensor status. For maximum security, all the doors and windows on your premises should be closed when you leave the building. In some cases, such as when using the security system when you stay at home, you may want to leave some doors or windows open. The system recognizes bypasses to resolve the open doors or windows. See "Bypassing/Un-Bypassing Sensors" on page 11. NOTE: Before you can arm the system, you must close or bypass all doors and windows with sensors. CHECKING FOR CLOSED SENSORS In most cases, you will be arming the security system with all of the sensor-protected doors and windows closed. The Control Panel provides easy ways to verify that all the sensor-protected doors and windows are closed before arming the system:

The Home button lights green when all perimeter sensors are closed. The Home perimeter sensor is open. Open interior sensors do not change this indication. button is not lit if any The Security button on the displays Home screen lights green when all perimeter sensors are closed. The Security button lights orange if any perimeter sensor is open. Open interior sensors do not change this indication. The Arm button on the displays Security screen and Menu screen lights green when all perimeter sensors are closed. If any interior sensors are open (or when any motion detector is triggered), a house icon displays on the status bar. The Arm button lights orange if any perimeter sensor is open. 9 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide VIEWING EACH SENSORS STATUS The Control Panel will also show you which sensor-protected doors and windows are open. Your installer has programmed descriptive names for each sensor-protected door and window. The Control Panels color display will show the names of which doors and windows are open. The top of the display on the Home, Security, and Menu screens shows sensor status. See System Status Icons on page 23. Tapping the Status button also displays a list of open sensors and general system status and alerts. Burglary Protection A D B C button lights orange if any perimeter sensor is open. A The Status Bar shows the system mode and shows system status icons. See System Status Icons on page 23. B The Arm button on the Security and Menu screens lights green when all perimeter sensors are closed. The Arm C The Home button lights blue when all perimeter sensors are closed. The Home button is not lit if any perimeter D The icon displayed shows that an interior sensor is open. Other icons can appear here as well. See System sensor is open. Status Icons on page 23. DEALING WITH A SENSOR FALSE ALARM When armed, the Control Panel reports alarm conditions on all sensors, both visually (on the status bar, and through a system alert icon) and audibly (through voice and chime announcements). There are rare times when an sensor will send a false alarm condition to the Control Panel. The conditions of a false alarm vary depending on the type of sensor and how that sensor communicates with the Control Panel. Perform a System, Sensor, and Panel Test to find any false alarm conditions. See "System Test" on page 29. See "Sensor Test" on page 29. See "Panel Test" on page 30. 10 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide SENSOR BYPASSING Before the system can be armed, all protected doors and windows must be closed or bypassed. You can bypass open sensors on protected doors or windows before arming the system. When a sensor is bypassed, the system ignores that the door or window is open. Two types of sensor bypasses are available:

Forced Manual In some cases (such as when using the security system for protection when staying at home), it may be desirable to leave some sensor-protected doors or windows open. Temporarily bypassing a sensor for this situation is called Force Bypassing. NOTE: Force bypasses are automatically removed when the system is disarmed. Sensor bypassing is also sometimes used when a sensor requires service. A sensors magnet may be missing, or an external switch contact connected to a sensor may be faulty. This causes the sensor to report as open to the Control Panel. In these conditions, you may need to schedule a service call with your qualified alarm service technician to repair or replace the troubled sensor. If the security system needs to be armed before the sensor can be serviced, the sensor can be manually bypassed so the rest of the system can be armed. Depending on programming, manual bypasses can remain in place until they are manually removed. NOTE: Bypassed Sensors offer no protection and cannot cause an alarm. Use Bypass if you want to arm your system with one or more sensors open and intentionally unprotected. Force Bypass All Sensors If any sensors are open when the system is disarmed, the Arm button on the panel turns YELLOW. When you tap the Arm button, the system automatically reveals the Bypass screen which lets you arm the system while forcing it to bypass all open sensors. Burglary Protection To force bypass all open sensors:

1 Ensure a sensor is open, such as a door or window. 2 At the Security or Menu screen, tap the YELLOW Arm button. 3 At the Bypass screen, tap Bypass All. This forces the system to bypass all of the open sensors in the list, including any open interior sensors. 4 At the Enter Code screen, enter a valid user code to bypass the sensor. NOTE: The Quick Bypass feature can also be configured by the installer. For details, refer to the Control Panels Installation & Programming Guide. 5 At the Ready to Arm (Sensors Bypassed) screen, tap Stay or Away. Later, when you disarm the system, the bypassed sensors are returned to their normal state. Bypassing/Un-Bypassing Sensors To add or remove sensors on the systems bypass list:

1 At the Home screen, tap Menu. 2 At the Menu screen, tap Toolbox. 3 Enter a valid user code to gain access to the Toolbox. 4 At the Toolbox (1 of 3) screen, tap Bypassed Sensors. 5 At the Bypassed Sensors screen, choose one of these options:

Adding a sensor to the bypassed list. Tap the BLUE button that corresponds to the desired sensor. When the button turns YELLOW, the system will bypass the sensor. Viewing Only Bypassed Sensors. Place a check-mark in the Show Bypassed Only box. Removing a sensor from the bypassed list. Tap the YELLOW button that corresponds to the desired sensor. The button turns BLUE when it is no longer on the bypassed list. 6 When finished, tap Back. 11 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide Burglary Protection Quick Exit in Stay Mode A programmable option, called Quick Exit may be displayed on the Security screen while the system is armed in Stay mode. Tap the Quick Exit button to start a timer that allows someone to exit or enter through a sensor-protected door that is programmed for delay without having to disarm the entire system. When the delay timer runs out, the system returns to the normal Stay mode. The Quick Exit option can be turned ON or OFF by the installer. See "Installer Programmed Options", on page 34, to understand the options that have been programmed for your system. SILENT CONTROL IN STAY MODE Three options for silencing the beeps and announcements are available when arming or disarming the system in Stay Mode. At the Home or Security screen, tap the Silent At the Ready to Arm screen, check the box adjacent Control button. to the Silent Exit option. On the Exit Delay screen, tap Silence. Selecting any of these options silences the Control Panel beeps and announcements. When arming, selecting the option doubles the length of the Exit Delay. STAY MODE Use Stay mode to partially arm the system when individuals will be occupying the premises. This arms only the sensor-protected perimeter doors and windows. This leaves interior motion sensors or other interior doors unarmed. In a home setting, Stay mode is typically used during the evening hours when occupants are no longer expected to leave or enter the premises. This allows occupants to move about the premises without triggering the burglary alarm. Because all the interior burglary protection is OFF, an alarm would only be triggered when a sensor-protected perimeter door or window is opened. Entry Delay in Stay Mode Certain sensors, such as a door, can be configured by your installer to use a delay timer before triggering an alarm. This provides a way for an authorized person to enter using a predetermined door to disarm the system before an alarm is triggered. To arm the system using an Entry Delay:

1 At the Security or Menu screen, tap the Arm button. 2 At the Ready to Arm screen, place a check-mark in the Entry Delay box. This is the default setting. NOTE: If you un-check the Entry Delay box, an alarm will be triggered when the sensor is opened while armed in Stay mode. 3 Tap Stay to arm the system NOTE: When re-entering the premises, the user must enter through the door(s) programmed to use the Entry Delay timer. This gives the user a specified amount of time to disarm the system. If the system is not disarmed in time, an alarm is triggered. 12 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide Burglary Protection NOTE: To arm the system, you may need to enter a user code if your installer has turned off the systems Quick Arming feature. 6 The system will arm and shows the Exit Delay counting down. When the Exit Delay expires, the system is fully armed in the Stay mode. AWAY MODE Away mode is for arming the system when everyone is leaving the premises. Away mode arms all sensor-

protected perimeter doors and windows, interior motion sensors, interior glass break sensors and any other sensor-protected interior doors. The premises must be unoccupied while the system is armed. Away mode is typically used for arming the system during the daytime hours in a residential location, and non-business hours in a commercial location. When the system is armed in Away mode, you cannot move about the premises without triggering the burglary alarm (if the system is installed with interior motion detectors). An alarm also occurs if any sensor-protected door or window is opened or glass breakage is detected (if glass breakage detectors are installed in your system). Exit and Entry Delays in Away Mode Certain sensors, such as a door, can be setup by your installer to have a delay before triggering an alarm. This provides a way for an authorized person to exit and re-

enter the premises without triggering an alarm. Exit Delay allows time to leave after arming the system. Entry Delay allows time to enter and disarm the system before an alarm is triggered. When arming the system in Away mode, an Entry Delay check box is shown on the Arming screen. By default, this option is checked, so the programmed delay doors allow time for disarming the system after the door is opened. If you clear the Entry Delay box, the delayed alarm trigger is removed from all sensor-protected doors programmed for delay. Those entrances instantly trigger an alarm if they are opened in Away mode. NOTE:

With the Entry Delay disabled, you must remotely disarm the system with a wireless key fob before entering. Arming to Stay Mode Use Stay Mode to arm the system when anyone is at home. Stay Mode normally has an Entry Delay so a user with a user code can re-enter without causing an alarm. 1 Close all protected perimeter doors and windows before arming. 2 Verify that the Home button on the Control Panel illuminates GREEN, indicating that the system is ready to arm. The Security and Arm buttons on the display are GREEN when all sensors are closed. NOTE: If you want to arm the system quietly without sounding any announcements, tap performing these steps:

At Ready to Arm screen, check the box adjacent to before the Silent Exit option. Or During Exit Delay tap Silence. 3 At the Security or Menu screen, tap Arm. NOTE: If any perimeter door or window sensors are open, the Bypass screen appears. Close all the sensors displayed, or tap Bypass All to force bypass the displayed sensors. NOTE: Bypassed sensors do not trigger an alarm. To bypass sensors, enter a user code unless the installer has set the system for Quick Bypass. 4 On the Ready to Arm screen, check the Entry Delay box when arming the system in Stay mode. If no one is expected to re-enter, the system can be armed without an Entry Delay. All perimeter doors will trigger the alarm instantly. To arm with instant alarms for all exit/ entry perimeter doors, un-check the box adjacent to the Entry Delay option. 5 Tap Stay to arm the system. 13 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide Exit Delay Restart The Exit Delay Restart option extends the Exit Delay one time if you need to re-enter the premises. With the Exit Delay Restart option, when you re-enter the premises after you have left, but before the Exit Delay timer expires, the Exit Delay timer restarts, giving you the full length of time to leave again. TIP: The Exit Delay Restart option only works once, each time the system is armed. Silent Control in Away Mode Three options for silencing the beeps and announcements are available when arming or disarming the system in Away mode. On the Control Panels Home and Security screens, a Silent Control button is displayed. On the Arming screen, a Silent Exit check box is displayed. On the Exit Delay screen, a Silence button is displayed. Selecting any of these options silences the Control Panel beeps and announcements. When arming, selecting Silent Control doubles the length of the Exit Delay. Quick Exit in Away Mode A programmable option called Quick Exit may be displayed on the Security screen while the system is armed in the Away mode. Tapping the Quick Exit button starts a timer to allow someone to exit or enter through a sensor-protected door programmed for delay without having to disarm the entire system. When the delay timer runs out, the system returns to the normal Away mode. TIP: If interior sensors are installed in the system in certain areas, do not violate those sensors when using the Quick Exit feature in Away mode. Auto Stay Mode The system may have been programmed by the installer for Auto Stay mode. If this option is on and the system is armed in Away mode, if an Exit/Entry Delay sensor is not triggered before the Exit Delay expires (no one leaves the premises), the system automatically arms in Stay mode instead of Away mode. NOTE: Quick options can be turned on or off by your installer. Refer to "Installer Programmed Options", on page 34, to see which options have been set for your system. Arming to Away Mode Use the Away mode to arm the system when everyone will be leaving the home. The Away mode normally has an entry delay so someone with a user code can re-enter Burglary Protection without causing an alarm. Interior and perimeter sensors are armed in the Away mode. 1 Close all sensor-protected doors and windows before arming. 2 Verify that the button on the Control Panel is illuminated green, indicating that the system is Ready to Arm. The Security button and Arm button on the display will also be green when all perimeter sensors are closed. If the icon is displayed on the status bar, an interior sensor is open. Make certain to close or manually bypass the interior sensors or an alarm will occur. 3 To arm the system quietly without sounding any button before performing announcements, tap the the next steps:

At the Arming screen check the Silent Exit box Or During the Exit Delay, tap Silence 4 At the Security screen, or the Menu screen, tap Arm. NOTE: If any perimeter door or window sensors are open, the Bypass screen appears. Close all the sensors displayed or tap Bypass All to force bypass the displayed sensors. NOTE: Bypassed sensors do not trigger an alarm. To bypass sensors, enter a user code unless the installer has set the system for Quick Bypass. 5 On the Arming screen, the Entry Delay check box option can be used with Away mode. The system can be armed without an Entry Delay. All perimeter doors trigger the alarm instantly. The system has to be disarmed with a wireless key fob. To arm with all exit/entry perimeter doors as instant, clear the Entry Delay check box. 6 Tap Away. To arm the system, enter a user code if your installer has turned off the systems Quick Arming feature. 14 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide 7 The system arms and shows the Exit Delay counting down. When the Exit Delay expires, the system is fully armed in the Away mode. NOTE: When the system is armed in the Away mode, beeps sound during the Exit Delay (these beeps become faster during the last 10 seconds). DISARMING THE SYSTEM To stop the Control Panel from triggering burglary alarms, the system needs to be disarmed. Disarming turns off the burglary detection part of the system for sensors that are not 24-hour sensors. Disarming also stops any type of alarm in process. Disarm the system from Stay mode before exiting the premises. The system should be disarmed from Away mode before or while entering the premises. When disarming from the Control Panel or wireless keypad, enter a valid user code. A wireless key fob can also be used to disarm the system. Entering a user code is not required when disarming with a wireless key fob. An important feature of the Control Panel is its ability to warn you if an alarm has occurred while you were away. If an alarm was triggered while the system was armed, the alarm siren runs for a preset length of time then stops. When you enter to disarm the system, instead of sounding the normal Entry Delay beeps, the Control Panel sounds repeated fast beeps to warn you that an alarm has occurred while you were away. When you enter your home to disarm the system, if you hear fast repeated beeps instead of the normal Entry Delay beeps, use Extreme Caution! An intruder may still be present inside the building! Wait outside and use a Cell Phone to call law enforcement for assistance. Burglary Protection Disarming from Stay Mode Disarm the system from Stay mode before exiting the premises. 1 At the Home screen, tap 2 At the Security screen or the Menu screen, tap Disarm. for Silent Control. This action displays the Disarm Code screen. 3 The left side of the screen shows any events that have occurred while the system was armed. 4 Enter a valid user code to disarm the system. In the event you tap the wrong key, the erases the entire entry. button Tap if you decide to not disarm the system at this time. Disarming from Away Mode The system should be disarmed from Away mode while entering the premises. 1 Enter the premises through a designated Entry Delay sensor-protected door. 2 The Disarm Code screen displays on the Control Panel and the Entry Delay beeps sound. The left side of the screen shows events that have occurred while the system was armed. 3 Enter a valid user code to disarm the system. In case you tap the wrong key, the erases the entire entry. button 15 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide IF A BURGLARY ALARM OCCURS If an armed sensor is tripped while the system is armed in the Stay or Away mode, an alarm occurs and the siren sounds. Delayed sensors start the Entry Delay to allow time to disarm the system. Instant sensors trigger the alarm right away. Most sensors trigger the alarm siren, some sensors may be set to trigger a silent alarm without sounding the siren. Burglary Alarm Siren If a burglary alarm is tripped while the system is armed, the Control Panel sounds the alarm siren for a preset time (see

"Installer Programmed Options" on page 34). After the time expires, the siren will stop. The system limits the number of times a sensor can re-

trigger an alarm while the system is armed. The setting is one to six times per sensor, per arming period (see

"Installer Programmed Options" on page 34). Alarm Memory If an alarm has occurred while the system was armed, the Disarm screen shows the time and date of the alarm and the sensor(s) that triggered the alarm. After the system is disarmed, the Alarm Memory screen appears. The Alarm Memory screen shows the sensor(s) that caused the alarm. If more than one sensor was triggered, the display shows the order in which the alarms occurred. Burglary Protection The alarm memory automatically clears the next time the system is armed. You can also check the Clear Alarm History box and tap OK to manually clear the alarm memory (24-hour fire and CO sensors that are still violated remain in alarm memory). Optional 2-Way Voice Communications 2-way voice communications provides a method for alarm verification and can provide emergency assistance. The Control Panel contains a built-in microphone that can monitor sounds around the area of the Control Panel. The built-in microphone and speaker allow 2-way voice communications with a Central Station operator after an alarm. The operator can converse with people in the premises through the Control Panels speaker and microphone. Your installer can set the system to use 2-way voice communications after an alarm and/or after a panic alarm is triggered. NOTE: If a panic alarm or sensor is set for a silent alarm, the operator can only listen and will not be able to talk. This is for your protection. KEY FOB: ARMING AND DISARMING Your system may be equipped with one or more wireless key fobs. Up to eight (8) key fobs can be used to control the system remotely. Each key fob has four (4) buttons and can perform five (5) functions. A user code is not required when arming or disarming the system with a wireless key fob. Several key fob options can be set by the installer. See

"Installer Programmed Options" on page 34. Arm with a Key Fob Stay Mode To arm the system to Stay mode using a key fob, tap the Stay button. NOTE: Depending on setup options, if any perimeter doors or windows are open, the system may not allow arming to Stay mode with a wireless key fob. See "Installer Programmed Options" on page 34. Away Mode To arm the system to Away mode using a key fob, tap the button. NOTE: Depending on setup options, if any perimeter doors or windows are open, the system may not allow arming to Away mode with a wireless key fob. See "Installer Programmed Options" on page 34. 16 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide Burglary Protection NOTE: If any perimeter door or window sensors are open, the system does not allow arming to Stay mode with a wireless keypad. All open sensors must be bypassed at the Control Panel first. Away Mode To arm the system to Away mode using a wireless keypad:

1 At the Home screen, tap Security. 2 At the Security screen, tap Arm. 3 Enter a valid user code. 4 Tap the Away button. 5 If Quick Arming has been programmed by your installer, just tap the Away button. NOTE: If any perimeter door or window sensors are open, the system does not permit you to use a wireless keypad to arm the system in Away mode. All open sensor-protected doors and windows must either be closed or bypassed at the Control Panel before arming with a wireless keypad. Disarm with a Keypad To disarm the system from Stay or Away mode, enter a user code. Activate a Fire Emergency To trigger an emergency fire alarm using a wireless keypad, press and hold the Fire button for two (2) seconds. NOTE: To use a wireless keypad to trigger a fire alarm, this option must already be enabled by your installer. Activate a Police Emergency To trigger an emergency police alarm using a wireless keypad, press and hold the Police button for two (2) seconds. NOTE: To use a wireless keypad to trigger a police alarm, this option must already be enabled by your installer. Disarm with a Key Fob To disarm the system from Stay or Away mode sing a key fob, tap the Disarm button. NOTE: To use your key fob to disarm your system, this option must already be enabled by your installer. Activate the Emergency Alarm To trigger an emergency alarm using a key fob, press and hold the Away button and Disarm button simultaneously for 5 seconds. NOTE: If an emergency alarm is, triggered by a key fob, it cannot be stopped using the key fob Disarm button. The alarm must be canceled at the Control Panel. Activate the Auxiliary Output To trigger the Control Panels auxiliary,output, tap the Auxiliary button. If you use the Auxiliary button, the auxiliary output controls the _________________. WIRELESS KEYPAD: ARMING AND DISARMING Your system may be equipped with one or more wireless keypads. Up to four (4) wireless keypads can be used to control the system remotely from the main Control Panel. Two types of wireless keypads are available. A wireless keypad without a screen, and a wireless touch screen keypad. The wireless touch screen keypad operates virtually the same as the Control Panel. Each standard wireless keypad has buttons for entering user codes, Stay and Away mode buttons, and Fire and Police emergency buttons. Check the See Installer Programmed Options on page 34, section in this guide to verify which 24-hour Fire and Police emergency buttons have been enabled by the installer. Arm with a Keypad Stay Mode To arm the system to Stay mode using a wireless keypad:

1 At the Home screen, tap Security > Arm. 2 Enter a valid user code. 3 Tap the Stay button. 4 If Quick Arming has been programmed by your installer, just tap the Stay button. 17 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide SMOKE, HEAT AND FREEZE PROTECTION 2 Evacuate all occupants from the premises and call your local Fire Department from a safe location. OR 1 If no flames or smoke are apparent, investigate the causes of the alarm. 2 Go to the Control Panel and enter your user code to stop the fire sounder and sirens. 3 Review the Alarm Memory to determine which sensor caused the alarm. 4 Go to the sensor and look for a possible reason the sensor tripped. 5 Correct the condition that caused the detector to trigger an alarm. Silencing a False Fire Alarm If the fire alarm is sounding due to a detector sensing burnt food or some other non-emergency condition:

1 Silence the fire alarm sounder by entering your user code. 2 Review the alarm memory to determine which sensor caused the alarm (See "Alarm Memory" on page 16). If the alarm restarts, there may still be smoke inside the detectors sensor. Re-enter your user code to stop the alarm from continuing to sound. 3 Fan the detector for 30 seconds to clear the detectors sensor chamber. 4 After the problem has been corrected, from the Alarm Memory screen, check Clear Alarm History, then tap OK. NOTE: Violated Fire and CO sensors clear from Alarm Memory screen only when the sensors return to normal operation. 5 Carefully inspect your premises for fire, heat, or gas if your Fire Alarms and CO Detectors remain in alarm state. Your residential system should be installed with Smoke, Heat, and Freeze alarms as well as Carbon Monoxide detectors as a part of an overall fire, heat, and gas protection system. Fire protection is active 24 hours a day, 365 days a year. NOTE: In Turkey, systems are installed with Smoke/Heat alarms. In the event of a fire or poisonous CO gas emergency, the installed smoke or carbon monoxide detector automatically activates your security system. Not only will the fire alarm itself emit a loud sound, the Control Panel emits an intermittent and loud horn on an external sounder (if an external sounder has been installed). The fire alarm sound continues until the timer expires on the Fire Alarm or until you enter a user code at the Control Panel. If the Alarm Sounds:

Get out and stay out. Never go back inside for people or pets. If you have to escape through smoke, get down low and go under the smoke. Call the fire department from outside your home. Initiating a Fire Alarm Manually If you become aware of a fire emergency before your detector(s) sense an issue:

IMPORTANT: Always yell Fire to alert everyone in proximity. 1 Go the Control Panel and tap the Emergency button. 2 At the Emergency screen, press and hold the Fire button for two (2) seconds. This action triggers the fire alarms sounder and siren. You can also trigger the fire alarm from the wireless keypad by holding down the Fire button. 3 Get out and stay out of the dwelling. Never go back inside for people or pets. 4 Call your local Fire Department from a safe location outside the dwelling. If the Fire Alarm Sounds Automatically If the fire alarm sirens are sounding:

1 If flames and smoke are present, yell Fire to alert everyone else. 18 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide Smoke, Heat and Freeze Protection RECOMMENDED FIRE ALARM LOCATIONS In the United States, this equipment shall be installed in accordance with the National Fire Alarm Code, ANSI/NFPA 72, (National Fire Protection Association, Batterymarch Park, Quincy, MA 02269). Printed information describing proper installation, operation, testing, maintenance, evacuation planning, and repair service is to be provided with smoke detectors and alarms. NFPA Standard #72 The National Fire Protection Associations (NFPA) Standard #72 recommends the following placement for smoke detectors:

Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household. The equipment should be installed as follows:

Install a smoke detector outside each separate sleeping area, in the immediate vicinity of the bedrooms and on each additional story of the family living unit, including basements (excludes crawl spaces and unfinished attics). Also install smoke detectors in the living room, dining room, bedrooms, kitchen, hallway(s), finished attics, furnace room, utility/storage rooms and attached garages. 19 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide Smoke, Heat and Freeze Protection Do Not Mount a Smoke Alarm Here Directly above a sink, cooker, stove, or oven Within 5 feet (1.5 m) of any cooking appliance Next to a door or window that would be affected by drafts (extractor fan or air vent) Outside In or below a cupboard Where air flow would be obstructed by curtains or furniture Where dirt or dust could collect and block the sensor Where it could be knocked, damaged, or inadvertently removed Fire-warning equipment for residential occupancies are capable of protecting about 50% of the occupants in potentially fatal fires. Victims include the elderly, children, and the physically or mentally impaired. Victims include any persons who cannot escape even when warned early enough that escape should be possible. For these people, other strategies such as protection-in-place or assisted rescue or escape would be necessary. Studies show that Smoke/Heat/Freeze Alarms may not awaken all sleeping individuals. Individuals in the household who are capable of assisting others are responsible for providing assistance to those who may not be awakened by the audible alarm or those who may be incapable of safely evacuating the area unassisted. A battery-powered alarm must have the specific battery type installed, be in good condition, and be mounted properly. The use of alcohol or drugs may also impair the ability to hear the audible alarm. For maximum protection, ensure that an audible alarm is installed on every floor. Smoke/Heat Alarms only provide protection to the residence if smoke actually reaches the alarm. The Smoke/Heat Alarm is not a substitute for an insurance policy. Home owners and renters should have adequate insurance to protect their properties. Emergency Action Plan Establish and regularly practice a plan of escape with all members of your household in the event of fire. The National Fire Protection Association recommends the following steps:

1 Mount your detector or your interior or exterior sounders where they can be heard by all. 2 Determine two means of escape from each room. One path of escape should lead to the door that permits normal exit from the building. The other should be an alternate escape (such as a window) should the path to a door be impassable. Station an escape ladder at such windows if there is a long drop to the ground. 3 Sketch a floor plan of the building. Show windows, doors, stairs, and rooftops that can be used to escape. Indicate escape routes for each room. Keep these routes free from obstructions and post copies of the escape routes in every room. 4 Ensure that all bedroom doors are shut while you are asleep to prevent deadly smoke from entering while you escape. 5 Try the door. If the door is hot, check your alternate escape route. If the door is cool, open it cautiously. Be prepared to slam the door shut if smoke or heat rushes in. 6 When smoke is present, crawl on the ground. Do not walk upright, since smoke rises and may overcome you. Clearer air is near the floor. 7 Escape quickly, but do not panic. 8 Establish a place outdoors, away from your house, where everyone can meet and then take steps to contact the authorities and account for those missing. Choose someone to assure that nobody returns to the house many die going back. 20 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide EMERGENCY FUNCTIONS 24-HOUR EMERGENCY BUTTONS Three 24-hour emergency functions are available on the Control Panel:

Panic Fire Emergency You can activate emergency functions using the Control Panel, as well as wireless sensors, wireless keypads or portable pendant devices such as the panic button remote. Tap the button to reveal the Emergency screen. This button does not trigger an alarm. During the installation, your installer programmed the emergency buttons that are displayed on the Emergency screen. If, however, no emergency functions are available, an information screen displays. To see which emergency functions are available on your system, tap the button. In the event of an emergency, press and hold the Emergency button for at least two (2) seconds to activate the alarm. C D A B A If emergency functions are available, the Emergency button is a solid white lighted button. B To display the Emergency screen, press the Emergency button. C The Emergency screen. D The Emergency screen displays the emergency options that are available on your system. Panic The Panic (or police) button sends an immediate panic report to the Central Station. During installation, the installer either set the system to sound the siren when the button is pressed, or to not sound the siren, but to trigger a silent alarm. Fire The Fire button sends an immediate fire report to the Central Station. The Control Panel sounds the fire horn when the button is pressed. Emergency The Emergency button sends an immediate report to the Central Station. The Control Panel sounds the siren when the emergency button is pressed. 21 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide SYSTEM TROUBLE ALERTS The system continually polls wired sensors, wireless sensors and the Control Panel itself to ensure optimal operating conditions at all times. If trouble is detected, the system alerts you. The system monitors the following conditions among others:

AC power to the Control Panel The telephone line (optional) The cell telephone connection (if used) The Control Panels backup battery The Sensor batteries Sensor supervisory status (if used) External sounder connection Sensor radio reception and sensor tampering

(sensors case opened) when disarmed Control Panel tampering (panels case opening) when disarmed (optional) Communication to the Central Station. You have the option to have any or all trouble conditions reported to the Central Station. If a trouble condition exists, service your system immediately to ensure no lapse in service or protection. TROUBLE ALERT ICON If the system detects trouble, it flashes the trouble Alert icon on the Security screen and sounds 6 alert beeps every minute. Scrolling text along the top of the display also describes the trouble condition. The trouble Alert right corner that shows the number of current trouble alerts. icon displays a number in the upper icon flashes until the trouble alerts The trouble Alert are acknowledged, then it remains constantly lit until all the troubles are corrected. When all troubles are corrected, the icon disappears completely. VIEW THE CURRENT TROUBLE ALERTS 1 To display all current trouble alerts, tap the Trouble Alert icon. 2 View the listed trouble events. If there are more than 3 alerts, use the and arrows to scroll through the list. 3 After viewing the trouble events, tap OK to acknowledge. This action silences the alert beeps. TROUBLE ALERT BEEP HOLD-OFF During the installation, as an option, the system can be programmed by your installer to suppress the trouble alert sounder from 10 pm to 9 am. Any trouble alerts will still be displayed and reported (if enabled), but the sounder does not beep during nighttime hours. Some trouble conditions may clear automatically while other trouble conditions may require service to correct. If a trouble condition still exists after 9 am, the sounder beeps to indicate trouble. NOTE: Regardless of whether the trouble alert sounder is suppressed or not, every trouble condition is always displayed on the trouble alert list and recorded in the system history event log. 22 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide SYSTEM STATUS ICONS AC POWER ON The AC Power icon shows the status of the AC power to the Control Panel. A WHITE plug appears when AC power is present. AC POWER OFF The AC Power icon shows the status of the AC power to the Control Panel. A RED X appears over the WHITE plug when AC power is absent. SOUNDER DISABLED If the systems internal sounder has been lowered and external sounder has been disabled by the installer for testing, the sounder disabled icon appears. It also flashes to indicate silent arming. LOW BACKUP BATTERY If the Control Panels backup battery tests low, the low backup battery icon appears. TEST MODE This icon displays when the system is in Walk Test mode. TOUCH SCREEN KEYPAD TRAFFIC An up arrow indicates the panel is sending information to the touch screen keypad (if installed). A down arrow indicates the touch screen keypad is sending information to panel. CELL RADIO If the option GSM (Cellular) Radio Module is installed, the Cell Radio icon appears while the Control Panel is receiving Over-the-Air (OTA) firmware updates. INTERIOR SENSOR OPEN If an interior sensor is open or a motion detector has just been activated, this icon appears. As a warning, the icon flashes during arming. 23 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide MESSAGING Your security system supports receiving messages from the Central Station. The messages can be about system upgrades, additional services, special regional weather alerts, etc. The messages can be sent for all system users to read, or as confidential messages that only the Master User can read. Messages can be tagged by the sender in the following manner:

Standard (blue message icon) Urgent (yellow message icon) Emergency Priority (red message icon) Up to 31 text messages can be stored in the Control Panels memory. You can review them through the Control Panels display. Displayed messages are sorted in the following manner:

Type Date Alphabetically message corner. Urgent messages display a yellow icon with an attention symbol in the upper right corner. bell symbol in the upper right corner. Emergency messages display a red the READING MESSAGES When a message icon appears on your Home screen:

message icon with 1 Tap the message icon button. The message list displays. The status bar shows the number of messages in memory, number of unread, and number of priority messages. Unread messages display in bold. 2 Use the or arrows to scroll through the message list. 3 Tap the message line itself to read the message. 4 Tap Back to return to the message list, or tap Delete to erase the message. NOTE: If you check the Mark Read box, the message remains on the message list, but it no longer displays in bold. 5 When deleting a message, a confirmation screen displays. Tap Delete Message, or to return to the message, tap Cancel. DISPLAYING MESSAGES When a message is sent to the Control Panel, 3 beeps sound and the message icon displays on the Security screen. Standard messages display a blue message icon with a number of unread messages in the upper right 24 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide READING CONFIDENTIAL MESSAGES NOTE: When a confidential message is sent to the Control Panel, only the Master User with the master user code can read the message. 1 To display the Message Filter screen, tap Filters. 2 Check or clear the boxes of the types of messages to display. To check all types of messages, tap All. To return to the message list, tap Back. Messaging When a confidential message appears, the Master User should do the following:

1 Tap the message line on the message list. If the message is a confidential message, the Code Entry screen appears. The filters will reset when the following occurs:

You select All Types Your message reviewing is over The system displays the Security screen SORTING MESSAGES To select the order in which messages are displayed on the message list, use the Message Sort screen. 1 To display the Message Sort screen, tap Sorts. 2 Enter the master user code. Other user codes are not accepted. 3 View the displayed message. 4 As detailed in "Reading Messages" on page 24, either save or delete. FILTERING MESSAGES To select the type of messages that are displayed on the message list, use the Message Filter screen. 2 To sort the messages, pick from the following options:

Date received Date expired Alphabetically 3 To reverse the display order, check the Reverse box. 4 To list urgent messages first, check the Priority box. 5 To return to the message list, tap Back. 6 When the message reviewing session is over, the sort options will reset. 25 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide SYSTEM TOOLBOX USER MANAGEMENT The system installer has programmed a master user code for your system. This code can be used to control the system, as well as to assign and change the other 59 user codes and access options. The master user code can also access several system settings in the Toolbox. NOTE: The other 59 user codes are restricted from accessing settings in the Toolbox. User Code Setup IMPORTANT: The holder of the master user code is the only user who has permission to set up other user codes. To set up the user codes:

1 At the Home screen, tap Security. 2 At the Security screen, tap Menu. 3 At the Menu screen, tap Toolbox. 4 Enter the master user code to access the Toolbox 5 On the Toolbox (1 of 3) screen, tap User Management. User Code Validity After the Confirmation screen appears and you click OK, the user codes Access Option screen appears. Select one of the three options to validate the user code:

Select Always to set this user code to always be valid. Tap Back. Select Never to set this user code to never be valid. Tap Back. Select By Schedule to set this user code to be valid only for selected days and/or times. User Code Access Schedules You can set up user codes with one or more Access Schedules. Access Schedules limit access to your system to people with user codes (such as maintenance personnel, service, or cleaning personnel). 6 The Users Management screen displays 3 users at a time. Use the and arrows to scroll through the list. Adding a User Code IMPORTANT: User codes 0000 and 0001 are not permitted. 1 Tap one of the Add User buttons. 2 Enter a unique four (4)-digit code for the new user code. Then tap OK. 3 Enter the code again to confirm it. Then tap OK. 4 At the Confirmation screen, tap OK to return to the User Management screen. Adding/Editing User Access Schedules 1 If you selected By Schedule for the user code, the Edit Schedules button appears. 2 To select or edit an existing user code Access Schedule, tap Edit Schedules. You can also create a new user schedule from the Edit Schedules screen. 3 The User Access Schedules screen displays all current schedules for the user code. 4 To add a new schedule, tap Add Schedule or to edit a schedule, tap an existing schedule. 5 You can select 1 of 3 Schedule types:

Recurring. Recurring applies to the days of the week and time period that this user code is valid. Date. Date applies to a single specific date and time period that this user code is valid. Date Range. Date Range defines a starting date, an ending date, and time period during which this user code is valid. 26 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide Recurring User Access Schedules You can define up to 7 Access Schedules for user codes with and Access Option of Always. 1 For the schedule type, select Always. 2 To view the User Access Schedule screen, tap the calendar button. 3 Select the day(s) of the week that this user code will be valid with the check boxes. 4 Tap the left and right time buttons to set the starting and ending times that this user code will be valid on the selected days of the week. 5 Tap OK to accept the schedule, or Cancel to return to the Schedule Type screen. Date User Access Schedule 1 For the schedule type, select Date. 2 To view the User Access Schedule screen, tap the calendar button. 3 To set the only month, day, and year that this user code is valid, tap the date button. 4 Tap the left and right time buttons to set the start and end times that this user code is valid on that date. 5 Tap OK to accept the schedule, or Cancel to return to the Schedule Type screen. Date Range User Access Schedule 1 For Schedule type, select Date Range. System Toolbox 6 To accept the schedule, tap OK or Cancel to return to the Schedule Type screen. Deleting User Access Schedule 1 On the User Management screen, select a user code that has a calendar schedule icon. 2 Tap the Edit Schedules button. 3 On the User Access Schedule screen, select the schedule to delete. 4 On the Schedule Type screen tap Delete. 5 A confirmation screen appears to verify that you want to delete the User Access Schedule. If Ok, tap Delete Schedule or tap Cancel to return to the User Access Schedule screen. 6 6 A second screen confirms that the schedule was deleted. Tap OK. User Codes Changing a User Code 1 At the User Management screen, tap the User button to change the user code. 2 Ensure that the current user code appears. Then tap 2 To view the User Access Schedule screen, tap the calendar button. 3 Tap the first day button to set the month, day, and year that this user code will first become valid. 4 Tap the last day button to set the month, day, and year that this user code will last be valid. 5 Tap the left and right time buttons to set the starting and ending times that this user code is valid during the date range. Change Pin. 3 Enter a new four (4)-digit user code to use as the PIN. Then tap OK. 27 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide System Toolbox Setting the Duress User Code 1 On the User Management screen, tap the User 8

(Duress) button. 2 A confirmation screen appears: Tap Create Duress User. 4 To confirm the user code, enter then new code again. Tap OK. 5 A confirmation screen appears, showing that the user code was changed. Tap OK. Deleting a User Code 1 To delete a user code from the User Management screen, tap the User button. 2 Tap Delete. 3 A confirmation screen appears to verify that you want to delete the user code. If Ok, tap Delete User or tap Cancel to return to the user codes Access Option screen. 4 A confirmation screen appears displaying the user code that was deleted. Tap OK. 3 Enter a four (4)-digit code to use as the new duress code. Then tap OK. 4 To confirm the duress code, enter the code again and tap OK. 5 A confirmation screen appears. Tap OK. 6 The User 8 edit screen appears. To return to the User Management screen, tap Back. Secret Duress Button On the Home screen, the system logo always appears in the lower right corner. The system logo is the secret duress button. TIP: You can change the master user code, but you cannot delete it. Duress User Code Setup The Duress Code (User Code #8) initiates a silent alarm for help by secretly sending a Duress report to the Central Station. Use the duress code when someone is forcing you to operate your security system against your will. When you use the duress code, a silent report is immediately sent to the Central Station and they will dispatch help. While Armed With the system armed, tapping the logo displays the standard disarm code entry screen. Use a valid user code or a duress user code to disarm the system. The system disarms normally, but a silent duress report is sent to the Central Station and they will dispatch help. If supported by the 2GIG Alarm dealer, the left side of this screen also displays contact information for the alarm dealer or Central Station. 28 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide While Disarmed You can also use the secret duress button while the system is disarmed. Tapping the system logo reveals the Enter Code screen. Enter the duress code to send a silent duress report to the Central Station and they will dispatch help. The system remains disarmed. If supported by the 2GIG Alarm dealer, the left side of this screen also displays contact information for the alarm dealer or Central Station. SYSTEM HISTORY The Control Panel keeps a log of system events in the order in which they occur. Each event is marked with the date and time that the event occurred. To make reading the log easier, the system history display can be filtered to show selected events only. The events that can be filtered for the system history log display are:

Armor disarm of the system Bypasses of sensors (force bypasses and manual bypasses) Alarms (alarms are displayed with a red stripe) Alerts (alerts are displayed with a yellow stripe) Some system events always display regardless of the filters selected. These events include:

Walk test started or terminated Programming mode started or terminated To view the system history log:

1 At the Home screen, tap Security. 2 At the Security screen, tap Menu. 3 On the Menu screen, tap Toolbox. 4 Enter a valid user code to access the toolbox. 5 At the Toolbox (1 of 3) screen, tap System History. The log of system events appears. Use the and arrows to scroll through the log. System Toolbox 7 Select the events to display with the check boxes. Tap All to select all the check boxes, or None to clear all the check boxes. 8 Tap OK when finished. SYSTEM TEST Even though your security system is self-monitoring, it is still important to regularly test the system manually. The System Test is used to test each of the sensors in the system. The master user code is required to test the system. While the system is in test mode, a T icon blinks on the upper right of the display. IMPORTANT: Test your Security System weekly to ensure continued protection and proper system operation. To test the system:

1 At the Home screen, tap Security. 2 At the Security screen, tap Menu. 3 At the Menu screen, tap Toolbox. 4 To access the system test, enter the master user code. 5 At the Toolbox (1 of 3) screen, tap System Test. 6 To choose the events to display, tap Filters. 29 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide System Toolbox Panel Test The panel test checks the Control Panels indicators and sounder. 1 At the System Test: Console screen, a list of tests to perform on the panel appears. Use the and arrows to scroll through the list. Sensor Test When each sensor is tested, the Control Panel does the following:

Beep sand announces the sensors name Displays green bar lights by the sensor name Displays green signal bars to show the strength of that sensors wireless signal. NOTE: Start and stop test reports are sent to the Central Station. 1 At the System Test: Console screen, a list of sensors appears. Use the and arrows to scroll through the list. 2 Go to each sensor listed, and trigger it. For door or window sensors, open and close the door or window. For motion detectors, stay out of the protected area for five (5) minutes, then walk through the area. For portable sensors and wireless keypads, tap a button. For smoke, CO, or glass break detectors, tap the detectors test button. TIP: When a red bar is displayed for a sensor, the test has failed. 2 Tap each button in the list. Then tap Yes or No to respond to the test question. 3 After answering all of the questions, tap OK. 4 At the System Test Successful screen, tap OK. CHIME SETUP On doors and windows monitored by sensors, the system can sound a chime to announce that the door or window was opened. Sensors can also be set to have the Control Panel say the name of the opening. TIP: The chime and voice announcements only sound while the system is disarmed. At the time of installation, the installer programs each sensors chime option. The person with the master user code can change the chime options for each sensor to further customize the system as desired. 3 When all sensors have been tested, tap OK. Then continue with the Panel Test. TIP: As a global system option, the chimes for all the systems sensors can be turned on or off using the Chime check box on the Menu screen. 30 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide System Toolbox To setup the chime options individually for each sensor:

1 At the Home screen, tap Security. 2 At the Security screen, tap Menu. NOTE: Select or clear the Chime and Voice check boxes to turn the system chimes and voice announcements ON or OFF (except for alarm voice messages). 3 At the Menu screen, tap Toolbox. 4 Enter the master user code to gain access to the Toolbox. 5 At the Toolbox (1 of 3) screen, tap Chime Setup. The Chime Setup screen displays each of the installed sensors that can chime and the option currently set for the sensor. Chime 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Option Disabled Voice Only Ding-dong #1 Ding-dong with Voice #1 Ding-dong #2 Ding-dong with Voice #2 Ding-dong #3 Ding-dong with Voice #3 Ding-ding Ding-ding with Voice Chime #1 Chime with Voice #1 Chime #2 Chime with Voice #2 To change the sensors chime options, tap the sensor button. TIP: There are 14 chime options for each sensor. 6 Check the option that you want for the sensor, then tap OK. 7 When you are finished, tap Back. ADJUSTING THE BRIGHTNESS/VOLUME You can adjust the brightness of the Control Panels display and the volume of the systems speaker that is best suited to your installed system. To set the brightness and volume:

1 At the Home screen, tap Security. 2 At the Security screen, tap Menu. 3 At the Menu screen, tap Toolbox. 4 Enter the master user code to gain access to the Toolbox. 31 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide System Toolbox To disable the touch screen for cleaning:

1 At the Home screen, tap Security. 2 At the Security screen, tap Menu. 3 At the Menu screen, tap Toolbox. 4 Enter a valid user code to gain access to the Toolbox. 5 At the Toolbox (1 of 3) screen, tap the arrow. 6 At the Toolbox (2 of 3) screen, tap clean screen. NOTE: The Display Cleaning screen appears for 30 seconds. It shows the time remaining. The touch screen is locked during this time. When the timer expires, the system returns to the Toolbox screen. 5 At the Toolbox (1 of 3) screen tap Brightness/Volume. You can set the brightness using the top bar. Adjust the level from 1 to 12 using the buttons on each end of the bar. 6 You can set the speaker volume for the chimes and announcements on the bottom bar. Adjust the level from 1 to 12 using the buttons on each end of the bar. NOTE: The volume setting does not effect the alarm sounder volume. 7 When you are finished, tap OK. ADJUSTING THE BACKLIGHT TIMEOUT The backlight timeout sets the length of time that the display stays lit after use. You can adjust the backlight to 30 seconds, 1, 2, 5, or 10 minutes, or to always (to light the display at all times). NOTE: To conserve the Control Panels backup battery, during an AC power failure, the display goes dark after 30 seconds regardless of this setting. To set the display backlight time:

1 At the Home screen, tap Security. 2 At the Security screen, tap Menu. 3 At the Menu screen, tap Toolbox. 4 Enter a valid user code to gain access to the Toolbox. 5 At the Toolbox (1 of 3) screen, tap the arrow. 6 At the Toolbox (2 of 3) screen, tap Backlight Time-out. 7 Choose one of the display backlight times and tap OK. CLEANING THE TOUCH SCREEN There is a special option for the Control Panel that enables you to clean the touch screen display. The option disables the touch screen for 30 seconds so the display can be cleaned with a dry, soft cloth. SET DATE AND TIME The Control Panel has a built-in clock and calendar. The Home screen displays the time and date. The time and date are also used for the system history and event logs that store data on system events. NOTE: During installation, your installer can set the system to automatically adjust for daylight saving time if its observed in your location. NOTE: The time and date are automatically set through the cellular radio by the Central Station if your Control Panel has a cellular radio installed. 32 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide System Toolbox To set the date and time:

1 At the Home screen, tap Security. 2 At the Security screen, tap Menu. 3 At the Menu screen, tap Toolbox. 4 At the Toolbox (1 of 3) screen, tap the arrow. 5 At the Toolbox (2 of 3) screen, tap Set Date or Set Time. 1 At the Home screen, tap Security. 2 At the Security screen, tap Menu. 3 At the Menu screen, tap Toolbox. 4 At the Toolbox (1 of 3) screen, tap the arrow. 5 At the Toolbox (2 of 3) screen, tap Version. 6 When finished, tap Back. 6 Use the and arrows to set the current date or time. Tap OK. 7 A confirmation screen showing the date and time set appears. Tap OK. DISPLAY FIRMWARE VERSION To troubleshoot your system, you can check the firmware version that has been installed. To display the firmware version:

DEALER INFO SCREEN AND CALL BACK BUTTON Your 2GIG Alarm Dealer may configure the Enter Your Code screen to display contact information for your 2GIG Alarm Dealer or the Central Station. Accessing the Dealer Info Screen To access the Dealer Info screen:

1 At the Home screen, tap the system logo. 2 At the Enter Your Code screen, enter the four (4)-digit master user code. 3 The left side of the Enter Your Code screen reveals contact information for your 2GIG Alarm Dealer or the Central Station. Requesting a Service Call Back To request a service call back:

1 At the Enter Your Code screen, a call back button appears at the bottom or the screen. 2 Tap the Call Back button to transmit a report to your alarm dealer or the Central Station. When the report is received by the 2GIG Alarm Dealer or Central Station, you will receive a call back in accordance with the terms of your dealers service agreement. For additional information about call backs, consult your 2GIG Alarm Dealer. 33 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide INSTALLER PROGRAMMED OPTIONS The installer can program different options to customize the installation. The options listed below show the default settings and a check box or area to denote custom settings. Siren Run Time If there is a burglary, panic (police), or emergency alarm, the Control Panel sounds the siren for a preset time. After the time expires, the siren will stop sounding. (Auxiliary alarms run for an unlimited time.) Four Minutes is the default, or the following:

Exit Delay The Exit Delay begins immediately after arming the system. The delay gives you time to leave through the designated exit/entry door without setting off the alarm. During the Exit Delay beeps sound, and faster beeps sound during the last 10 seconds. NOTE: Arming remotely does not start an Exit Delay. 60 Seconds is the default, or ________ For ________ Door. 8 Minutes 12 Minutes 16 Minutes Unlimited Sensor Trigger Limit The system limits the number of times a sensor can re-

trigger an alarm while the system is armed. The setting is 1 to 6 times per sensor, per arming period. Two Triggers is the default, or the following:

1 Trigger 3 Triggers 4 Triggers 5 Triggers 6 Triggers Fire Horn Run Time If there is a fire or carbon monoxide alarm, the Control Panel sounds the fire alarm horn for a preset time. After the time expires, the fire alarm horn will stop sounding. Four Minutes is the default, or the following:

8 Minutes 12 Minutes 16 Minutes Unlimited Entry Delay The Entry Delay begins when the designated entry/exit door is opened while the system is armed. The delay gives you time to disarm the system before triggering the alarm. You must enter a valid user code on the Control Panel or Wireless Keypad before the Entry Delay time expires. During the Entry Delay, beeps sound to remind you to disarm the system. The system supports two different Entry Delays:

Entry Delay #1 is for your primary entrance door 30 Seconds is the default, or _________ Entry Delay #2 is for a secondary entrance (such as a garage door) and is usually set longer to give you time to get to the keypad and disarm the system. 45 Seconds is the default, or _________ For ________ Door 24-Hour Emergency Functions The system can be configured to display three 24-hour emergency buttons on the Control Panel: Panic, Fire, and Emergency. The installer can set which emergency buttons on the Control Panel are active. Panic (Audible) Panic (Silent) Fire Emergency 34 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide Quick Arming Quick Arming allows you to arm your system without having to enter a user code. When you tap the Stay or Away button, the system will start to arm without requesting a user code. Off On Quick Bypass Normally sensors that are open at the time the system is armed will require force bypassing by entering your user code. The system can be set so a user code is not required to bypass open sensors when the system is armed. Off On Quick Exit The Quick Exit option allows you to start the Exit Delay while the system is armed. This allows you to leave the premises without having to disarm and rearm the system. When the Quick Exit option is on, a Quick Exit button will display on the Security screen. Tap the button to start the Exit Delay. After Quick Exit, the system will fully re-arm in the mode that it was in before (Stay or Away mode). Off On Auto Un-bypass Normally, sensors manually bypassed with the User Toolbox will automatically have their bypasses removed when the system is disarmed. The system can be set so sensors that have been manually bypassed will stay bypassed until the bypass is manually removed. Off On Auto Stay The Auto Stay option will change the arming mode if no one exits after arming the system in Away mode. When the system is armed in the Away mode the Exit Delay will begin. With the Auto Stay option on, if a designated exit/entry door does not open and close during the Exit Delay, the system will arm in the Stay mode instead of the Away mode. Off On System Toolbox Key Fob Sound The system can be set so when it is armed or disarmed by a wireless key fob, a beep will sound through the internal and external sounders to indicate that the key fobs signal was received. This helps in installations where the Control Panel is not visible or there are no other system status indications at the key fobs location. Off On Key Fob Disarm After Sound The system can be set so that when it is disarmed with a wireless key fob after an alarm has occurred, a special series of beeps will sound through the internal and external sounders. This option serves as an alert to warn you to approach the premises with caution as an intruder may still be present. Off On Key Fob Options The installer selects which options are enabled for each key fob (1-8) used with the system. Refer to the table below for the options selected for your key fobs:

1 2 3 4 5 6 7 8 Option Arm without Exit Delay Allow key fob disarming Enable key fob auxiliary key Auxiliary Alarm Audible Alarm Silent Panic Alarm Fire Alarm Emergency Keys Disabled All Key Pads Key Fob Arming Bypass Options Option Auto-bypass all open perimeter sensors and un-bypass a sensor if closed while the system is armed Auto-bypass open perimeter sensors permanently while armed Allow key fob arming only when all perimeter sensors are closed 35 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide System Toolbox Dialer Delay If an alarm occurs, the system will delay dialing for a short time to allow you to disarm the system in case the alarm was accidentally tripped. The dialer delay reduces nuisance traffic to the Central Station and can prevent receiving fines that many cities impose when police respond to a false alarm. Your installer also can program the system for no dialer delay. NOTE: The dialer delay is also known as the abort window. It gives you time to disarm, but doesnt delay the siren from sounding. Disarming during the abort window can display a cancel message depending on the Cancel Display setting

(see "Cancel Display"). 30 Seconds is the default, or ______ Seconds. 2-Way Voice The system can connect with a Central Station operator so they can converse with people on the premises after an alarm. The 2-way voice option allows communication to and from the Control Panel and the Central Station. 2-way voice communications will occur after the system has made its alarm report. Your installer sets which sensors can trigger the 2-way voice option. Off On Wireless Keypad Emergency Keys Each standard wireless keypad has Fire and Police emergency buttons that can be enabled or disabled for each keypad. Refer to the table below for options set for your keypads:

Option Emergency Keys Enabled Emergency Keys Disabled 1 2 3 4 Exit Delay Restart The Exit Delay Restart option will extend the Exit Delay one time if you need to re-enter the premises. When the system is armed in the Away mode or Stay mode, the Exit Delay gives you time to leave without setting off the alarm. With the Exit Delay Restart option, re-entering the premises after you have left, but before the Exit Delay timer expires, will restart the Exit Delay timer, giving you the full length of time to leave again. The restart option only works once, each time the system is armed. Off On Cancel Display A cancel message will be sent to the Central Station if the system is disarmed within a preset period of time after an alarm is triggered. The system can be set to display that a cancel report was sent, or for higher security, the system can be set not to display the cancel message. Off On Cancel Time To limit responses to false alarms, a cancel message will be sent to the Central Station if the system is disarmed within a preset period of time after an alarm is triggered. The alarm report is always sent, but it will be followed by a cancel report if you disarm the system within the preset time. This option helps the Central Station to determine whether you accidentally caused the alarm or if the alarm was caused by an intruder. It also lets the Central Station know that you have returned to the premises. Even if a cancel message is sent, the Central Station will verify the alarm and possibly dispatch help. The cancel message may be processed by the Central Station at a later time depending on system programming. Five Minutes is the default, or _______ Minutes 36 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide INSTALLER SPECIFIC INFORMATION User Codes Master User User 2 User 3 User 4 User 5 User 6 User 7 User 8 User 9 User 10 User 11 User 12 User 13 User14 User 15 User 16 User 17 User 18 User 19 User 20 User 21 User 22 User 23 User 24 User 25 User 26 User 27 User 28 User 29 User 30 User 31 User 32 User 33 User 34 User 35 User 36 User 37 User 38 User 39 User 40 User 41 User 42 User 43 User 44 User 45 User 46 User 47 User 48 User 49 User 50 User 51 User 52 User 53 User 54 User 55 User 56 User 57 User 58 User 59 User 60 IMPORTANT: If you have logged user codes here to maintain security, keep this guide in a secure location!

37 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide Zones Zones 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 37 39 40 41 42 43 44 45 46 47 48 Installer Specific Information Wireless Protection Zones (1-48) Zones Hardwired Zone (49) 49 Keyfobs (51-58) Keypads (59-62) Wireless Protection Zones (63-74) Duress (92) Fire (95) Medical (96) Police Panic (99) 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 92 95 96 99 38 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide SERVICE INFORMATION Your local Alarm dealer is the person best qualified to service your alarm system. Be sure to set up a routine service schedule with your local Alarm installer. 39 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide REGULATORY INFORMATION Wireless Product Notice Radio controls provide a reliable communications link and fill an important need in portable wireless signaling; however, there are some limitations which must be observed. For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range. A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. Changes or modifications to the device may void FCC compliance. Infrequently used radio links should be tested regularly to protect against undetected interference or fault. A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the end users. FCC Notice This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturers instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Relocate,the Console away from the TV/radio receiver. Plug the Console into a different wall outlet so that the Console is on a different branch circuit. Reorient the TV/radio antenna. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. 40 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide IMPORTANT NOTICE ALARM SYSTEM LIMITATIONS This security system can not offer guaranteed protection against burglary, fire, or other emergencies. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:

Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (sensors) do not work without power. Battery operated devices do not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC do not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless sensors may be blocked or reflected by metal before they reach the alarm Control Panel, even if the signal path has been recently checked during a weekly test. Blockage can occur if a metal object has been moved into the sensors signal path. A user may not be able to reach a panic or emergency button quickly enough. Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner, or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or awaken deep sleepers. While smoke detectors have played a key role in reducing residential fire deaths, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this system may not work are where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow occupants to escape in time to prevent injury or death. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as ten years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. Although, installing an alarm system may make homeowners eligible for lower insurance rates, an alarm system is not a substitute for insurance. Homeowners, property owners, and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. Panel Operating Conditions For optimal performance, the Control Panel should be operated under the following conditions:

Operating Temperature 0C to 49C (32F to 120F) Humidity 0 90% Non-condensing 41 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide LIMITED WARRANTY This Nortek Security & Control LLC product is warranted against defects in material and workmanship for one (1) year. This warranty extends only to wholesale customers who buy direct from Nortek Security & Control LLC or through Nortek Security & Control LLCs normal distribution channels. Nortek Security & Control LLC does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealers warranty, if any. There are no obligations or liabilities on the part of Nortek Security & Control LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties for functionality, are valid only until the warranty expires. This Nortek Security & Control LLC Warranty is in lieu of all other warranties expressed or implied. For warranty service call your local alarm installation and service professional shown on the back cover of this User Guide. Covered by one or more claims of patents: http://sipcollc.com/patent-list/ and http://intusiq.com/patent-list/. 42 Copyright 2018 Nortek Security & Control GC2.5 Wireless Security System | User Guide 5919 Sea Otter Place, Suite 100 Carlsbad, Ca. 92010

(800) 2GIG-TECH YOUR LOCAL ALARM AND SERVICE PROFESSIONAL:

43 www.nortekcontrol.com 10022313 X4Copyright 2018 Nortek Security & Control