INSTR,INSTL,MC3089 ,1 CH,TX - LINEAR P/N: 10029379_Rev-X1 - INK: BLACK - M ATERIAL: 20 LB. MEAD BOND - SIZE : 9.000 X 3.500 - SCALE: 1-1 - SIDE 1 OF 2 PRINTERS INSTRUCTIONS:
WARNING:
the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CLL lortnoC & ytiruceS ketroN 0202 thgirypoC 10029379_Rev-X1 USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340 www.nortekcontrol.com Multi-Code INSTALLATION INSTRUCTIONS DIGITAL TRANSMITTER MODEL 3089 Congratulations! You have just purchased a MULTI-Code Digital Transmitter, on the market. With a little care this transmitter should provide you with many years of excellent service. Please take a moment to read the follo ACCESSING THE CODE SWITCH Insert a small coin into the slot located at the bottom end of the transmitter. Twist the coin and remove the access cover to expose the code switch and battery compartment. SELECTING A CODE You may set your transmitter to any code you desire but be sure that the code you set matches the code that has been set on your radio receiver. The digital code is determined by the positions of the 10 small switches numbered 1 through10 located in the receiver and transmitter. Any combination of ON (CLOSED) or OFF (OPEN) positions can be selected by using a small screwdriver or ball point pen. (NOTE: The switches are in the On position when the side next to the number is pressed in.) In setting your own personal code we strongly urge that several coding schemes be avoided: ALL ON; ALL OFF; 2, 4, 6, 8, 10 ON; 1, 3, 5, 7, 9 ON. These positions are similar to our or other manufacturers test positions, or are frequently used. Once the code has been set, check the operation and replace the hatches. INSTR,INSTL,MC3089 ,1 CH,TX - LINEAR P/N: 10029379_Rev-X1 - INK: BLACK - M ATERIAL: 20 LB. MEAD BOND - SIZE : 9.000 X 3.500 - SCALE: 1-1 - SIDE 2 OF 2 PRINTERS INSTRUCTIONS:
10 9 8 7 6 5 4 3 2 1 TRANSMITTER INSTALLATION The transmitter is completely self contained, including battery, and can be operated while mounted in the car. It is supplied with a clip for attaching to the sun visor, if desired. If the clip is used attach to the case by sliding it into the recess provided TRANSMITTER BATTERY REPLACEMENT Replacement battery - 9 volt NEDA 1604 (Eveready 216 or equivalent). The battery in the transmitter can be checked or changed by removing the front lower half of the transmitter. Refer to the directions under accessing the code switch for battery replacement. TO REPLACE OR ADD A SET A replacement or new transmitter or receiver may be purchased by specifying the Model Number and the RF frequency digital code can be matched to the companion receiver or transmitter by following the above procedure. OPERATIONAL CHECK To check operation, move back a reasonable distance (about 50 ft.) and press the transmitter button. Operation should be reliable at this distance but environment and location of both the transmitter and receiver will affect the range. If the transmitter is stowed well out of sight, it may be necessary to remove it from its mounting and hold near the windshield. Try different locations and positions. If operation is still unsatisfactory, the problem may be isolated by:
1. Checking the door operator. If the door will not open when the wall button is pressed, the problem is likely to be the operator. If the door will open by pressing the wall button, but not when the radio control button is pressed, the problem is probably in the radios. 2. Replacing the transmitter battery. If after performing the above operational checks, the controls still do not function, they should be returned to your dealer for repair or replacement. FCC & IC Notice This device complies with Part 15 of the FCC Rules and Industry Canada license exempt standard(s). Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference received that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
1) lappareil ne doit pas produire de brouillage, et 2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.