FCC ID: 2AZ5M-RL61A1 Bluetooth Module

RL61A1 Bluetooth Module User manual CompanyOE Technology (Shenzhen) Co., Ltd. Product DescriptionBluetooth Module Model No.RL61A1 1Product introduction 1.1Product Overview Ou Yi Technology RL61A1 series smart module is a wireless communication module with mesh networking function. It is mainly used in smart light control, home/hotel automation control, consumer electronics, industrial control, etc., to meet the requirements of low power consumption, low delay, and short-range wireless data communication. 1.2Product features Maximum receiving sensitivity-91dBm Maximum transmitting power10dBm Voltage input range: 2.5 V 3.3 V Modular operating temperature applied to intelligent lighting-40 +85 PowerconsumptionSleepmodeaslowas6uA Support for Mesh Various peripheral device interfaces Maximum 6 channel PWM output 2 UART external communication interfaces Maximum of 14 customizable GPIOs for switching input and relay control output Support point-to-point and point-to-multipoint communication RL61A1 Bluetooth Module User manual 1.3Product parameters Category Item Wireless parameters Frequency range Parameter 2.4G Receiving sensitivity Minimum-91dBm Type of antenna PCB antenna Data interface PWM Working voltage Power supply current Low power current Transmission distance mesh Working temperature Module size UART 3.3V 80mA 6uA Outdoorspace100m

-40 +85 15.5x12x2.0mm Table 1: Technical specifications of RL61A1 seriesmodules Hardware parameters 1.4Product application Home/Hotel/Building Automation Intelligent light control system Industrial control Low power wireless sensor networks RL61A1 Bluetooth Module User manual 2Product Hardware Introduction 2.1 Module shape and interface 2.1.1 OE-B01 external copper wire antenna universal Bluetooth module 2.1.1.1 Pin description The shape of the module is as follows, with 22 external pins. Please refer to the table for detailed pin functions. GND RF GND AIO[1]

AIO[2]

AIO[3]

UART_TX UART_RX WWHITE CWHITE PWM5 GND VCC SWDIO SWCLK RST_N BLUE GREEN RED IIC_SCL IIC_SDA INT0 Pin 1 2 Pin function GND RF Detailed description Modular input The outer connecting foot of Bluetooth can be selected RL61A1 Bluetooth Module User manual according to the actual situation. The reserved welding pad can be used to directly weld the copper wire antenna Modular input Customizable analog IO pin;

Customizable analog IO pin;

Customizable analog IO pin;

Module serial port, can be customized as GPIO function;

Module serial port, can be customized as GPIO function;

Warm-white PWM output, high efficiency; Can be customized as GPIO function Cold white PWM output, high efficiency; Can be customized as GPIO function Reserved PWM output pin, can be customized for GPIO function The system interrupt input port can be customized as GPIO function if low power mode is not used Can be customized as GPIO function;

Can be customized as GPIO function;

Red PWM output, high efficiency; Can be customized as GPIO function Green PWM output, high efficiency; Can be customized as GPIO function Blue PWM output, high efficiency; Can be customized as GPIO function System reset pin, internal default pull-up, if not necessary, please suspend or reserve TestPoint Module debug port, suspended or reserved TestPoint Module debug port, suspended or reserved TestPoint 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 GND AIO[1]

AIO[2]

AIO[3]

UART_TX UART_RX WWHITE CWHITE PWM5 INT0 IIC_SDA IIC_SCL RED GREEN BLUE RST_N SWCLK SWDIO VCC GND 3.3V DC power input Modular input Table 2: Pin description of the RL61A1 Bluetooth module Note 1: Pin numbers start from the first on the upper left of the module and are arranged counterclockwise. Note 2: The function and pin definitions of this module will vary slightly when used as different devices, refer to the detailed documentation for the corresponding firmware. PCB package size RL61A1 Bluetooth Module User manual PCB package size is shown in the figure above, module size is 23.3*12mm, pin spacing is 1.27mm, pin pin width is 0.846mm. 2.2 Suggestions for using module PCB It is recommended to use LDO to supply 3.3V DC and provide the driving capacity of at least 80mA peak current. It is recommended to place a 10uF capacitor at the module power inlet. In PCB layout planning, BLE modules should be placed away from magnetic field sources such as transformers and coils. Antenna areas should be kept PCB design clear and not protected by any enclosure. Antennas must be at least 10mm away from metal or tall components. If there are other special requirements, the module can be customized. FCC Modular Usage Statement 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.10 below concerning the need to notify host manufacturers that further testing is required.3 Explanation: This module meets the requirements of FCC part 15C (15.249).it specifically establish the Conducted Emission, Radiated Spurious Emission, Field strength of fundamental, Band Edge Emission, 20dB Bandwidth. 2.3 Summarize the specific operational use conditions Describe use conditions that are applicable to the modular transmitter, including for example any limits on antennas, etc. For example, if point-to-point antennas are used that require reduction in power or compensation for cable loss, then this information must be in the instructions. If the use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturers instruction manual. In addition, certain information may also be needed, such as peak gain per frequency band and minimum gain, specifically for master devices in 5 GHz DFS bands. Explanation: The EUT has one PCB antenna, the antenna cannot be replaced by other authorized antennas. 2.4 Limited module procedures If a modular transmitter is approved as a limited module, then the module manufacturer is responsible for approving the host environment that the limited module is used with. The manufacturer of a limited module must describe, both in the filing and in the installation instructions, the alternative means that the limited module manufacturer uses to verify that the host meets the necessary requirements to satisfy the module limiting conditions. A limited module manufacturer has the flexibility to define its alternative method to address the conditions that limit the initial approval, such as: shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation. The alternative method could include that the limited module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host. The module manufacturer must state how control of the product into which the modular transmitter will be installed will be maintained such that full compliance of the product is always ensured. For additional hosts other than the specific host originally granted with a limited module, a Class II permissive change is required on the module grant to register the additional host as a specific host also approved with the module. Explanation: The module is a limited single module, Any modifications made to the module will void the Grant of Certification, this module is limited to OEM installation only and must not be sold to end-users, end-user shall have no manual instructions to remove or install the device, only software or operating procedure shall be placed in the end-user operating manual of final products. shielded. 2.6 RF exposure considerations It is essential for module grantees to clearly and explicitly state the RF exposure conditions that permit a host product manufacturer to use the module. Two types of instructions are required for RF exposure information: (1)to the host product manufacturer, to define the application conditions(mobile, portable xx cm from a persons body); and (2) additional text needed for the host product manufacturer to provide to end users in their end-product manuals. If RF exposure statements and use conditions are not provided, then the host product manufacturer is required to take responsibility of the module through a change in FCC ID (new application). Explanation: This module complies with FCC RF radiation exposure limits set forth for an uncontrolled environment." This module is designed to comply with the FCC statement, FCC ID is: 2AZ5M-RL61A1. 2.7 Antennas A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved as limited modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an omni-directional antenna is not considered to be a specific antenna type)). For situations where the host product manufacturer is responsible for an external connector, for example with an RF pin and antenna trace design, the integration instructions shall inform the installer that unique antenna connector must be used on the Part 15 authorized transmitters used in the host product. The module manufacturers shall provide a list of acceptable unique connectors. Explanation: The EUT has one PCB antenna, the antenna cannot be replaced by other authorized antennas, and the gain of each replacement antenna is no more than 1dBi 2.8 Label and compliance information Grantees are responsible for the continued compliance of their modules to the FCC rules. This includes advising host product manufacturers that they need to provide a physical or e-label stating Contains FCC ID with their finished product. See Guidelines for Labeling and User Information for RF Devices KDB Publication 784748. Explanation: The host system using this module, should have label in a visible area indicated the following texts: "Contains FCC ID: 2AZ5M-RL61A1. 2.9 Information on test modes and additional testing requirements Additional guidance for testing host products is given in KDB Publication 996369 D04 Module Integration Guide. Test modes should take into consideration different operational conditions for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. The grantee should provide information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host. Grantees can increase the utility of their modular transmitters by providing special means, modes, or instructions that simulates or characterizes a connection by enabling a transmitter. This can greatly simplify a host manufacturers determination that a module as installed in a host complies with FCC requirements. Explanation: OE Technology (ShenZhen) Co., Ltd. can increase the utility of our modular transmitters by providing instructions that simulates or characterizes a connection by enabling a transmitter. 2.10 Additional testing, Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Explanation: The module without unintentional-radiator digital circuity, so the module does not require an evaluation by FCC Part 15 Subpart B. The host shoule be evaluated by the FCC Subpart B. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment

OE Technology (ShenZhen) Co., Ltd. C5266091_X10_Ed.2 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AZ5M-RL61A1 To Whom It May Concern, Date: May 28, 2021 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No Short-Term Confidentiality NOTE 2 No No No No NOTE 1 NOTE 1 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are the equipment. The public considered as proprietary information in operation of disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. short-term Confidentiality, the applicant requests the exhibits selected In case of above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 1/1 C5266091_X10_Ed.2 Sincerely, Signature:

Name: Leo Li Title: Manager 1/1

Model difference declaration letter Differences Description We OE Technology (ShenZhen) Co., Ltd. state:

Product Model Name Bluetooth Module RL61A1, RL61A2,RL61A3,RL61B1 The above product with same circuit, PCB layout, electrical parts, materials and wiring structures, Appearance shape, the materials of decorative accessories is same, only different color, Signatory Date: 05-28-2021

<Signature>

NameLeo Li TitleManager CompanyOE Technology (ShenZhen) Co., Ltd. Address: Block B3 212,Baoyuan Road Famous Industrial Products Show and Purchasing Center,Xixiang Street,Baoan District,Shenzhen

C5266091_X8_Ed.1 Letter of Authorization OE Technology (ShenZhen) Co., Ltd. Company: OE Technology (ShenZhen) Co., Ltd. Address: Block B3 212,Baoyuan Road Famous Industrial Products Show and Purchasing Center,Xixiang Street,Baoan District,Shenzhen Product Name: Bluetooth Module Model Number: RL61A1, RL61A2,RL61A3,RL61B1 FCC Identifier: 2AZ5M-RL61A1 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. is allowed to forward all Name: Leo Li Date: May 28, 2021 Title: Manager Signature of applicant:

1/1

C5266091_X9_Ed.2

< OE Technology (ShenZhen) Co., Ltd.>

Modular Transmitter Approval Request Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Company name: OE Technology (ShenZhen) Co., Ltd. FCC ID: 2AZ5M-RL61A1 Gentlemen, In accordance with 47CFR 15.212 Modular Transmitters and KDB 996369 D01 Module Certification Guide v01r04. FCC ID: 2AZ5M-RL61A1 has been examined against the following requirements. Items to be covered by Single modular transmitters. Requirement per 15.212 and KDB 996369 D01 Modular Certification Guide v02 Explanation from Grantee

(do not write yes/no, but explain why product complies/how it is achieved) 1. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly not compliance 2. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal All modulation and data inputs are buffered by circuitry on the transmitter chip RL610, as is shown in the schematic. 3. The module must contain power supply regulation on the module 4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b) 5. The module must demonstrate compliance in a stand-

alone configuration Power supply regulation is provided by circuitry on the transmitter chip RL610, as is shown in the schematic. The module contain a permanently attached antenna and spurious emission have been fulfilled. Please reference the exhibition Test Report. Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 6. The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements) 7. The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee 8. The module must comply with RF exposure requirements The instruction on the labelling rule of the end product has been stated in the Users manual of this module. Please also see the exhibition Label Sample. The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. Please refer exhibition RF Exposure for the compliance of MPE RF exposure rule. Name: Leo Li Title: Manager Signature of applicant Date: 2021-05-28