Order Number Test Report Number
: GETEC-C1-17-532
: GETEC-E3-17-052 FCC Part 15 subpart C Page 1 / 1 APPENDIX H
: USERS MANUAL EUT Type: Remote Controller FCC ID.: OZ5B526A B526A Manual 1 - Mechanical Requirements 1.1 - Design
- Dimensions : 160 x 47 x 17.8mm TOP CASE BOTTOM CASE BATTERY COVER RUBBER BUTTON MATERIAL MATERIAL COLOR PRINT COLOR MATERIAL MATERIAL COLOR MATERIAL FORMING COLOR FORMING COLOR 4-A PRINTING COLOR SURFACE TREATMENT ABS BLACK SMI-G 715 (BLACK) ABS BLACK SILICONE RUBBER BLACK TRANSLUCENT CLEAR WHITE SILICONE COATING Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 1/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/
B526A Manual 1.2 - Picture (for reference only) Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 2/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/
B526A Manual 1.3 - Batch Number Adhesive label is attached at the inside part of the battery cover 1.4 - Packing 1.4.1 - Packing Process
- PE bag dimensions : 83 x 286 mm (LDPE 0.05t)
- Quantity Per Box: 140pcs
- Box dimensions : W 600 x D 400 x H 200 mm 1.4.1 - Palett definition
- Pallet dimension : W 1200 x D 800 x H 170 mm
- Full pallet dimension : W 1200 x D 800 x H 1770 mm
- Quantity per pallet : 4,480pcs (4 boxes / layer - 8 layers) Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 3/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/
B526A Manual 2 - Electrical Requirements 2.1 - Electrical Characteristic Condition Bluetooth Low Energy Specification TC-3000
(RF measuring instrument) Parameter Frequency Range Channel RF Power Test channel RF Power Modulation Characteristics Carrier Frequency Offset and Drift PAvg PMax Pmin f1 avg f2 avg f2/f1 f2min f2rate fTx-fn f0-fn f1-f0 fn-f(n-5) Operating Voltage LVI Voltage RF (Bluetooth) Low Voltage Indicate Operating current (IR) Power: 3V Operating current (RF KEY) Operating current (RF+Voice) Leakage current RF range (distance) IR Range VOICE 300Hz 2KHz 3.8KHz
- Hardware Version: V1.0 Power: 3V Non-directional distance Direct Horizontal Voice Inspection JIG Spec 2.402 ~ 2.480 40 0 19 01
+1
-1 225~275 185 0.8 92.5 99 150 50 20 20 2.0~3.6 2.25 0.2 35 12 25 10 10 12 7 (30)
-15 ~ -5
-21 ~ -2 20 ~ 0 Unit
[GHz]
[Num]
[dBm]
[Num]
[dBm]
[dBm]
[dBm]
[KHz]
[KHz]
[KHz]
[%]
[KHz]
[KHz]
[KHz]
[KHz]
[V]
[V]
[mA]
[mA]
[mA]
[]
[m]
[m]
[m]
[dB]
[dB]
[dB]
Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/
Page 4/ 9 B526A Manual 3 - Software Requirements 3.1 - Bluetooth 4.2 LE identification a) Device Name: Channel Master Remote b) Vender ID: 0x02AF c) Product ID: 0x2025 d) Software Version : V0007 3.2 - Pairing mode a) At first time pairing or after Factory Reset, RCU works only in IR. b) Press [OK] and [APPS] keys for longer than 4 seconds. LED stays ON while pressing
[OK] and [APPS] keys. c) After 4 seconds, the LED starts blinking so that to confirm the remote has entered into pairing mode. d) After RCU has entered pairing mode, RCU can send the IR signal of Up, Down, Left, Right and OK keys. e) If pairing is successfully made, the LED goes OFF and remote starts working in Bluetooth. f) If the user presses any key during pairing mode, the remote stops pairing and goes back to IR mode, excepted Up, Down, Left, Right and OK keys. g) If pairing is not successfully made for 90 seconds, the LED goes ON for 4 seconds and then goes OFF. The remote stops pairing and goes back to IR mode if first time pairing and after Factory Reset. 3.3 - Re-pairing mode a) Press [OK] and [APPS] keys for longer than 4 seconds. LED stays ON while pressing
[OK] and Google [APPS] keys. b) After 4 seconds, the LED starts blinking so that to confirm the remote has entered into pairing mode. c) After RCU has entered pairing mode, RCU can send the IR signal of Up, Down, Left, Right and OK keys. Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 5/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/
B526A Manual d) If pairing is successfully made, the existing pairing table is deleted, the LED goes OFF and the remote works in Bluetooth with the new device. e) If the user presses any key during pairing mode, excepted Up, Down, Left, Right and OK keys, the remote stops pairing and the previous paired status is restored, f) If pairing with new device is not successfully made for 90 seconds, the LED goes ON for 4 seconds and then goes OFF. The previous paired status is restored. 3.4 - Factory Reset mode a) Press [APPS] and [0] keys for longer than 4 seconds. LED stays ON while pressing
[APPS] and [0] keys. b) The remote blinks 3 times to confirm that it is deleting the existing pairing table and TV
& Audio IR setting. c) When Factory Reset is completed, LED goes OFF and the remote works in IR mode. 3.5 - IR backup in paired mode a) If, for any reason, the RF connection is lost, the remote sends the IR code of the corresponding pressed key. b) The remote tries to reconnect for sending the RF code. 3.6 - Voice Search initiated by the remote a) For Voice function, it is recommended to be within 5 meters from the receiver. b) Distance between mouth and microphone should be within 40 cm (15~20cm recommended). c) Microphone key pressed and released, remote sends key pressed event, key released event to the STB and the STB sends back the START command to the remote. d) The LED starts blinking, the remote transmits the voice data for 10sec timeout duration. e) After timeout duration, the remote stops transmitting the voice data and the LED is turned off. f) Or When the remote receive the stop command from STB, thre remote stops transmitting the voice data and the LED is turned off. Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 6/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/
B526A Manual Note: if any key is pressed within the timeout duration, the remote stops transmitting the voice data and activate the pressed key event. 3.7 - Voice Search initiated by the launcher a) For Voice function, it is recommended to be within 5 meters from the receiver. b) Distance between mouth and microphone should be within 40 cm (15~20cm recommended) c) User selects and validates the voice search on the launcher by using navigation and OK keys. d) STB sends the voice search START command to the remote. e) After timeout duration, the remote stops transmitting the voice data and the LED is turned off. f) Or When the remote receive the stop command from STB, thre remote stops transmitting the voice data and the LED is turned off. Note: if any key is pressed within the timeout duration, the remote stops transmitting the voice data and activate the pressed key event. 3.8 Setup for TV & Audio a) As long as the RCU is paired to the STB, the RCU can then automatically be set up by the STB for TV or Audio control. b) The STB can set the RCUs IR using the command defined in Appendix1. c) When the setting is completed, the Volume key and the Power key output the IR signal according to the set value. d) If the RCU receives the send keycode command, it outputs the IR signal of the corresponding key. However, the RCU will not store the set value. e) The TV database uses the set number from 0001 to 1999. f) The Audio database uses the set number from 3001 to 4999 3.9 Remove the TV & Audio a) Press [OK] and [V-] keys for longer than 4 seconds. LED stays ON while pressing [OK]
Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 7/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/
B526A Manual and [V-] keys. b) After 4 seconds, LED will be blink 3 times. c) Press 01 to remove the TV setting. Or press 02 to remove the Audio setting. d) LED will be blink 3 times to confirm the remote has remove the setting. 3.10 - Couch mode a) If a key or multiple keys are pressed continuously for more than 30s, the remote stops transmission (except pairing combination) in order to protect the battery discharge. 3.11 - OAD mode a) OAD proceeds according to the RTK specification. 3.12 - Key codes a) In Bluetooth mode, HID Profile is used. b) In IR Mode, NEC format is used
- Structure of the NEC format: Custom1 - Custom2 Data Inverse data For MUTE to be seen as 0x16-0x20-0x25. Another alternative is 0x1620-0x25 Custom1: 0x16 Custom2: 0x20 c) Code list is detailed in Table 1 Key Code Name Event constant name Info Power D-pad up D-pad down D-pad left D-pad right D-pad center Back Guide APPS Volume +
KEYCODE_PROG_GREEN KEYCODE_POWER KEYCODE_DPAD_UP KEYCODE_DAPD_DOWN KEYCODE_DPAD_LEFT KEYCODE_DPAD_RIGHT KEYCODE_DPAD_CENTER KEYCODE_BACK KEYCODE_SELECT_PROGRAM_GUIDE KEYCODE_HOME
-
IR Code
(Data) HID Usage Page Usage ID 0xA6 0x21 0x15 0x16 0x17 0x18 0x19 0x48 0xC0 0x47
-
0x07 0x0C 0x0C 0x0C 0x0C 0x0C 0x0C 0x0C 0x0C 0x0C
-
0x006A 0x0030 0x0042 0x0043 0x0044 0x0045 0x0041 0x0224 0x008D 0x0223
-
Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 8/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/
B526A Manual Volume -
DVR Channel +
Channel -
Rewind Play/Pause Fast Forward
-
KEYCODE_MEDIA_SELECT_HOME KEYCODE_CHANNEL_UP KEYCODE_CHANNEL_DOWN KEYCODE_MEDIA_REWIND KEYCODE_MEDIA_PLAY_PAUSE KEYCODE_MEDIA_FAST_FORWARD 1 2 3 4 5 6 7 8 9 0 Microphone 3.13 - Battery level KEYCODE_1 KEYCODE_2 KEYCODE_3 KEYCODE_4 KEYCODE_5 KEYCODE_6 KEYCODE_7 KEYCODE_8 KEYCODE_9 KEYCODE_0 KEYCODE_.and >4 KEYCODE_SEARCH Table 1: Code list
-
0xA0 0x33 0x34 0x51 0x52 0x53 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0xA1 0x46
-
0x0C 0x0C 0x0C 0x0C 0x0C 0x0C 0x07 0x07 0x07 0x07 0x07 0x07 0x07 0x07 0x07 0x07 0x07 0x0C
-
0x009A 0x009C 0x009D 0x00B4 0x00CD 0x00B3 0x001E 0x001F 0x0020 0x0021 0x0022 0x0023 0x0024 0x0025 0x0026 0x0027 0x0037 0x0221 a) RCU sends the information for battery level using Bluetooth battery service. b) Level of LVD is 2.25V 0.2V. c) If the battery voltage as reached the LVD value, RCU cannot enter the pairing mode. d) If the battery voltage is under 2.0V, RCU does not operate. e) When the battery voltage is 2.1V or more, the RCU operates again. 4 - EMC Conformity Assesment of compliance of the product to the requirements relating to Electromagnetic Compatibility is based on the following standards:
4.1 FCC : FCC Part 15 Subpart C 15.247 4.2 IC : RSS-210, RSS-247 4.3 Mexico : IFETEL, NOM Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 9/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Note : The manufacturer is not responsible for any Radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. End users must follow the specific operating instructions for satisfying RF exposure compliance. Industry Canada(IC) Statement
[English]
Statement This device complies with Industry Canadas License-exempt RSSs. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Industry Canada Statement
(For Canada) This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. IC Radiation Exposure Statement
(For Canada) This equipment complies with IC radiation exposure limits set forth for an Uncontrolled environment.