MRF-250 INSTALLATION MANUAL Multi-Room No-Pointing RF Control of Audio/Video Components MRF-250 Installation Manual 2004 Universal Remote Control, Inc. The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL,TECHNI-
CAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this manual may be subject to change without prior notice. Home Theater Master is a registered trademark of Universal Remote Control, Inc. Entertainment Made Simple is a trademark of Universal Remote Control, Inc. All other brand or product names are trademarks or registered trademarks of their respective companies or organizations. 500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 TTAABBLLEE OOFF CCOONNTTEENNTTSS Introduction Features and Benefits Parts Guide Front Panel Mounting Plate Power LED Status LED Front Blaster Rear Panel Flashers Power Supply Bottom Panel Receiver ID#
A Standard MRF-250 System Standard Installation Step by Step Front Blaster Overload Disabling the Front Blaster - Step by Step Controlling An Array of Identical TVs Identical Components - Step by Step Programming For Multiple Equipment Locations Frequently Asked Questions Specifications 1 2 2 3 3 3 3 3 4 4 4 4 4 5 5 7 7 8 8 11 12 12 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN Introduction The combination of the MX-3000 with its companion MRF-250 base station will enable you to place your audio/video components out of sight behind closed doors and/or in another room of your house. The MX-3000 sends radio signals to the MRF-250 throughout your house (50-100 away, indoors or outdoors). The MRF-250 converts your commands to the infrared signals that control your A/V components. 1.The MX-30000 remote con-
trol sends radio waves in every direction, so you dont have to point the remote any-
more!
2.The MRF-250s built-in Front Blaster sends commands to components in the same cabinet space as the MRF-250. 3. Self-adhesive Flashers affix to the Infrared sensors on the front panels of your components. The Flashers relay commands to components out of sight of the MRF-250s Front Blaster. The flashers plug in to the MRF-250s rear flasher line outputs via their 10 foot cables. PPaaggee 11 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN Features and Benefits NNoo MMoorree PPooiinnttiinngg -- RRaaddiioo WWaavveess PPeenneettrraattee WWaallllss,, DDoooorrss aanndd FFlloooorrss The MRF-250 receives the RF signals of the MX-3000 remote control from any direction. You no longer need to point the remote control at any of your A/V components. You can also place the components distracting blinking lights and displays behind closed doors and/or in another room!
RReelliiaabbllee CCoonnttrrooll TThhrroouugghhoouutt YYoouurr HHoouussee The MRF-250 receives RF signals from your MX-3000 from within a radius of 50 to 100 feet enabling you to control out of sight audio/video components behind walls and closed doors. Range depends on the structure of your home and the amount of interference generated by computers, microprocessors and other devices within and nearby your home. UUpp TToo SSiixxtteeeenn EEqquuiippmmeenntt LLooccaattiioonnss CCoonnttrroolllleedd FFrroomm AAnnyy MMXX--33000000 Each MX-3000 can be programmed to operate equipment placed throughout the house, by installing an MRF-250 base station at each location. Each MRF-
250 is assigned one of 16 unique ID#s. select a device located in the Den, the MX-3000 only talks to the MRF-250 in the Den. When you select a device located in the Family Room, the MX-3000 only talks to it!
In operation its simple: when you NNoo PPooiinnttiinngg RReemmoottee CCoonnttrroollss IInn EEvveerryy RRoooomm You can opt to control a multi-room or multi-zone system via RF remote con-
trol by placing an MX-3000 in each room of your home. CCoonnttrrooll AA MMeeddiiaa RRoooomm AArrrraayy ooff IIddeennttiiccaall TTVVss The MRF-250s unique assignable IR flashers enable your installation to control up to six identical TVs. The intelligent routing of the MRF-250 will send your commands only to the TV you select on your MX-3000. The other identical TVs will not receive commands. Of course, if your system utilizes identical satellite receivers, cable boxes, VCRs or disc changers you can utilize IR rout-
ing just as easily for them. If you have more than six identical components, up to 16 additional MRF-250s can be installed to control them (thus allowing up to 96 identical components in one house). Parts Guide The MRF-250 RF Base Station includes:
1 - MRF-250 Receiver with integrated antenna 1 - Mounting Plate for wall mounting the MRF-250 4 - Screws for wall mounting the mounting plate 1 - 9V-300mA Power Supply 6 - Flashers with 10 foot plug in cables. PPaaggee 22 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN MRF-250 Details Red POWER LED lights when the MRF-250s power supply is plugged into an active AC outlet. Red STATUS LED lights when the MRF-250 receives an RF signal from the MX-3000. The MRF-250s slots enable the Mounting Plates matching guides to slide and snap into place for mounting on the wall. Front Blaster sends Infrared com-
mands to all A/V components in the same cabinet space. The MRF-250 Mounting Plate Using the four enclosed screws, you can choose to fix the mounting plate to a wall or the back of your component cabinet. PPaaggee 33 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN Integrated Antenna swings in any direction to optimize RF recep-
tion and range. Included 9V power supply plugs into the MRF-250s power connector. Six Rear Flasher Line Output Jacks connect flashers for control of A/V components out of sight of the MRF-
250s Front Blaster. Six Plug-In Flashers are supplied with 10 foot cables and six extra self-adhesive pads (in case a flash-
er has to be repositioned). Bottom panel Dial sets the Receiver ID# when more than one MRF-250 receiver is used. PPaaggee 44 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN A Standard MRF-250 System A standard system utilizes no identical components and only one equipment location. However, you can add any number of MX-3000 remote controls to your home! MX-3000s are available as an accessory purchase without an MRF-250 for standard system installations that already have an MRF-250. You can add any number of MRF-250 base stations in a standard system as well. 250 receivers as needed by ordering an accessory MRF-250 base station. If you need more than six flasher outputs you may add additional MRF-
Do not change the factory default settings in RF Control section of MX-3000 Editor when you download to your MX-3000s. You do not need to utilize MX3000 Editors Program Step 9 (RF Control), since the factory settings will work fine!
Standard Installation Step by Step SStteepp 11 -- PPrrooggrraamm aanndd DDoowwnnllooaadd ttoo tthhee MMXX--33000000 Connect your MX-3000 to your PC and program the IR commands and macros as you like. Since your MX-3000 sends both IR and RF, you can test your pro-
gramming as you go by pointing the MX-3000 at the components and using MX-
3000 Editors TEST and Macro Play features if you place your laptop PC in the same room as the components (with the cabinet doors open and in line of sight). For a detailed explanation of how to program, use the downloadable Programming Manual or the animated Tutorial. Both are available as free down-
loads from the www.hometheatermaster.com website. IImmppoorrttaanntt NNoottee:: DDoo NNOOTT ppoowweerr uupp tthhee MMRRFF--225500 aatt tthhiiss ppooiinntt.. YYoouu nneeeedd ttoo tteesstt yyoouurr IIRR ccoommmmaannddss aanndd MMaaccrrooss lliinnee ooff ssiigghhtt vviiaa IIRR oonnllyy aatt tthhiiss ppooiinntt!!
Once you have completed and downloaded your programming to the MX-
3000 remote control, you are ready to test RF operation via the Front Blaster and (if necessary) the self-adhesive flashers that connect to the MRF-250s flasher line outputs. SStteepp 22 -- PPllaaccee tthhee MMRRFF--225500 The MRF-250 should be placed so that the Front Blaster will control as many of the systems A/V components as possible. If you are connecting the out-
board flashers to the rear Flasher outputs only, the MRF-250 may be con-
cealed and mounted to the rear wall or back of the system cabinet.The PPaaggee 55 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN mounting plate slides apart from the receiver, screws to the wall or cabinet with the enclosed screws, then the receiver is slid back into place. SStteepp 33 -- CCoonnnneecctt tthhee PPoowweerr SSuuppppllyy aanndd IInnsseerrtt tthhee BBaatttteerriieess Connect the 9V power supply to an active UNSWITCHED AC outlet. The MRF-
250 must always be powered up to operate.The red POWER LED should light. Insert the batteries in the MX-3000 remote control. SStteepp 44 -- TTeesstt tthhee MMXX--33000000 Observe the MRF-250s STATUS LED blinking while you press and hold a pro-
grammed button (one with an actual command).This tells you that the MRF-
250 is receiving the RF commands of the MX-3000. However, if the LED con-
tinues to flicker after you release the button, you are receiving RF Interference and you must move the MRF-250 to another location. SStteepp 55 -- OOrriieenntt tthhee AAnntteennnnaa ffoorr OOppttiimmuumm RRaannggee If you need to extend the range of the remote, try adjusting the angle of the MRF-250 receiving antenna via its pivoting ball mount. SStteepp 66 -- TTeesstt OOppeerraattiioonn WWiitthhoouutt FFllaasshheerrss With the MX-3000s IR output blocked by a jacket or pillow, test the control of your components using just the Front Blaster. In most cabinets, the MRF-250s Front Blaster will control any A/V components in the same cabinet space by reflections from the cabinet walls and doors. Make sure that the components operate with the cabinet doors closed or open. If a component is placed too far away from the front blaster, you will need to utilize the included Flashers plugged into the MRF-250s rear Flasher Line Output jacks. If you have problems with components that are close to the Front Blaster, see the next page and the section on Front Blaster Overload. SStteepp 77 -- CCoonnnneecctt FFllaasshheerrss ttoo OOuutt ooff SSiigghhtt AA//VV CCoommppoonneennttss IImmppoorrttaanntt NNoottee:: TTeesstt tthhee ooppeerraattiioonn BBEEFFOORREE ssttiicckkiinngg tthhee ffllaasshheerr iinn ppllaaccee.. Use a flashlight to identify the correct location of the components IR sensor, then try a few commands while moving the flasher around the face plate of the component. The most reliable operation typically occurs a half inch or so away from the IR sensor. Once you have found the spot that gives the most reliable operation, peel off the protective backing of the self-adhesive tape on the included Flashers and stick them in place. IImmppoorrttaanntt NNoottee:: AAllwwaayyss rreeppllaaccee tthhee sseellff--aaddhheessiivvee ttaabbss iiff yyoouu hhaavvee ttoo rreeppoossii--
ttiioonn aa ffllaasshheerr.. SSiixx eexxttrraa sseellff--aaddhheessiivvee ttaabbss aarree ssuupppplliieedd ffoorr tthhiiss ppuurrppoossee.. PPaaggee 66 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN Front Blaster Overload A few models of audio/video components can be OVERLOADED by the Front Blaster. If you are having intermittent or inconsistent results with a particular component, try repositioning the MRF-250 and facing the Front Blaster in a different direction. If this improves the situation but is impractical, it may be necessary to utilize the self-adhesive flashers only and follow the steps below to Disable the Front Blaster. This will limit the number of components your MRF-250 can control to six. If you have more than six components you can purchase an additional MRF-250 (available as an accessory alone from your Home Theater Master dealer). Do not change the receiver ID# (use the same ID # as the first unit) then follow the steps on the following pages:
Disabling the Front Blaster - Step by Step Plug the MX-3000 back into the PC. Open your saved configuration and follow these steps to turn off the front blaster:
SStteepp 11 -- OOppeenn tthhee RRFF SSeettuupp WWiinnddooww The RF Setup window opens after selecting RF Control from the Program Menu. SStteepp 22 -- RReevveeaall tthhee RReecceeiivveerr sseettttiinnggss Extend the RF Setup window by click-
ing on the Receivers button. SStteepp 33 -- TTuurrnn ooffff tthhee FFrroonntt BBllaasstteerr Click on the cell in the IR Blaster column.A list box will appear. Select OFF from the list. NNeexxtt,, cclliicckk oonn OOKK ttoo aappppllyy yyoouurr cchhaannggee.. SStteepp 44 -- SSaavvee aanndd DDoowwnnllooaadd ttoo tthhee MMXX--33000000 SAVE your changes using File|Save and DOWNLOAD to the MX-3000. PPaaggee 77 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN Controlling An Array of Identical TVs
(or VCRs, Receivers, CD players etc.) There are several considerations to take into account when you are installing an MRF-250 to control an array of identical components:
1. You cannot use the Front Blaster to control identical components. You must use Flashers instead. You can still use the Front Blaster in a cabinet that is out of sight of the identical components to control the rest of your system. 2. Each identical component must receive IR commands ONLY from a dedicat-
ed Flasher affixed to its front panel. The IR output of the MX-3000 should be disabled for each identical component. It can still be utilized for the rest of your system!
3. You must note the NUMBER of the Flasher Output you have utilized for EACH of the identical components. NOTE:
If the identical components are near each other the Flashers and the actual sensor window of the component should be blocked with black electrical tape (sometimes more than one layer is needed). Identical Components - Step by Step SStteepp 11 -- CCrreeaattee aa DDeevviiccee ffoorr EEaacchh TTVV iinn MMXX--33000000 EEddiittoorr The MX-3000 can control up to 20 devices. You must create one device for each of your identical TVs. In this example, six iden-
tical TVs are utilized in a Media Room array. The programmer has created devices for all of the equipment in the cabinet on Main Page 1. On Main Page 2, he/she has created a device for each of the TVs. SStteepp 22 -- PPrrooggrraamm OOnnee DDeevviiccee WWiitthh IIRR ccoommmmaannddss.. Using either the IR Database or Learning, program one of the identical devices to operate one of TVs (leave the others powered off right now).Test all com-
mands and Save your work. PPaaggee 88 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN SStteepp 33 -- CCooppyy TThhee PPrrooggrraammmmeedd DDeevviiccee In tree view, right click on the device you programmed. From the context menu that appears, select COPY. SStteepp 44 -- PPaassttee TThhee PPrrooggrraammmmeedd DDeevviiccee In tree view, right click on the first device that is NOT PROGRAMMED. From the context menu that appears, select PASTE. Repeat this PASTE on all of the other identical device. Save your work. SStteepp 55 -- OOppeenn tthhee RRFF SSeettuupp WWiinnddooww The RF Setup window opens after selecting RF Control from the Program Menu. The RF Setup window is composed of a spread sheet of options for EACH of your devices. By looking at the Signal column, you can see that the factory default programming sets all of the devices to send both IR and RF commands. If you look at the column for Flashers, you can see that the default sends IR commands for all devices to ALL of the flashers. Both options must be changed for identical components.Additionally, if you are not using it, you may wish to disable the Front Blaster (see page 7 for directions). SStteepp 66 -- AAddjjuusstt tthhee SSiiggnnaall FFoorr EEaacchh ooff tthhee IIddeennttiiccaall DDeevviicceess The RF Setup window enables you to adjust the Signal output by the MX-3000 for each device individually, by clicking on the intersection of a row and a col-
umn and then selecting RRFF from the three options shown in the pull down list box . PPaaggee 99 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN Click on the cell for the first identical TV, by crossing the device row with the Signals col-
umn. Signal Column TV1 Device Row SSeelleecctt RRFF ffrroomm tthhee tthhrreeee ooppttiioonnss sshhoowwnn ffoorr EEAACCHH ooff tthhee iiddeennttiiccaall TTVVss.. YYoouu mmaayy lleeaavvee tthhee ootthheerr ccoommppoonneennttss ooff tthhee ssyysstteemm sseett ttoo IIRR && RRFF.. SStteepp 77 -- AAddjjuusstt tthhee FFllaasshheerrss FFoorr EEaacchh ooff tthhee IIddeennttiiccaall DDeevviicceess The RF Setup window enables you to adjust which Flashers output by the MX-
3000 for each device individually, by clicking on the intersection of a row and a column and then selecting 11--66 from the seven options shown in the pull down list box. Flasher Column Click on the cell for the first identical TV, by crossing the device row with the Flashers column. TV1 Device Row SSeelleecctt tthhee ccoorrrreecctt FFllaasshheerr ((rreeffeerr ttoo yyoouurr ccoonnnneeccttiioonn nnootteess)) ffoorr EEAACCHH ooff tthhee iiddeennttiiccaall TTVVss.. YYoouu mmaayy lleeaavvee tthhee ootthheerr ccoommppoonneennttss ooff tthhee ssyysstteemm sseett ttoo AALLLL.. SStteepp 88 -- AAppppllyy,, SSaavvee,, DDoowwnnllooaadd aanndd TTeesstt First click on the OK button of the RF Setup window. Next, Save your work. Finally, download to your MX-3000. When you select TV1 with your MX-3000, commands are only sent to it. Likewise for the rest of your identical TVs!
PPaaggee 1100 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN Programming For Multiple Equipment Locations You can operate up to 16 different equipment locations, each with an MRF-
250 assigned a unique Receiver ID#. You program each of your MX-3000s to talk to the equipment locations you want by assigning each of your devices to a receiver. First, you must add and name your receivers for the locations they are placed in:
SStteepp 11 -- OOppeenn tthhee RRFF SSeettuupp WWiinnddooww The RF Setup window opens after selecting RF Control from the Program Menu. SStteepp 22 -- RReevveeaall tthhee RReecceeiivveerr sseettttiinnggss Extend the RF Setup window by clicking on the Receivers button of the RF setup window. SStteepp 33 -- AAdddd,, NNaammee aanndd AAssssiiggnn RReecceeiivveerr IIDD##
Using the controls at the bottom extended portion of the RF Control win-
dow, add new receivers and rename them for the Add new receivers by clicking on the Add button. Delete receivers by selecting them first by clicking on their Name, then clicking the Delete button. Assign the correct Receiver ID# for each LOCATION by clicking on the desired CELL and selecting the ID# you want from the pull down list. Each LOCATION should have a unique ID#. install multiple MRF-250s in one location. It is ok to You may rename the Default receiver to something more descriptive by clicking on the Rename button. SStteepp 44 -- SSaavvee aanndd DDoowwnnllooaadd ttoo yyoouurr MMXX--33000000.. PPaaggee 1111 MMRRFF--225500 BBAASSEE SSTTAATTIIOONN Frequently Asked Questions CCaann II uussee ffllaasshheerr//eemmiitttteerrss tthhaatt II hhaavvee aallrreeaaddyy iinnssttaalllleedd iinn tthhee ssyysstteemm ttoo ccoonn--
nneecctt ttoo tthhee MMRRFF--225500??
Yes, the flashers are compatible, however flashers from other companies are equipped with a mini plug that is too large to fit the MRF-250s flasher jacks. Use Radio Shack part # 274-327 to convert 3.5mm plug Flasher/Emitters to the MRF-250. II hhaavvee aa rrooww ooff iiddeennttiiccaall TTVVss.. IIvvee ccoorrrreeccttllyy sseett tthhee ffllaasshheerr oouuttppuuttss uussiinngg MMXX--
33000000 EEddiittoorr,, yyeett wwhheenn II sseenndd aa ccoommmmaanndd ttoo oonnee ooff tthheemm,, tthhee TTVV nneexxtt ttoo tthhee sseelleecctteedd TTVV aallssoo rreessppoonnddss.. HHooww ddoo II ssttoopp tthhiiss??
Use an opaque material like electrical tape to cover the flasher and the front panel sen-
sor of each of the TVs. Sometimes several layers are necessary. HHooww ccaann II iinnccrreeaassee tthhee rraannggee ooff tthhee MMXX--33000000??
Often, you can increase range by repositioning the MRF-250 and/or by re-orienting the antenna. Try to avoid placing the MRF-250 directly adjacent to satellite receivers, personal computers or any other component using high speed microprocessors if possible. Warranty The MRF-250 is covered against any manufacturers defects or workmanship for a period of one year from the date of purchase if purchased from an authorized Home Theater Master dealer. Units purchased from online auction sites or other unauthorized resellers have no warranty.This warranty does not cover the following items:
-Damage from misuse, neglect, or acts of nature.
-Products that have been modified or incorporated into other products.
-Products purchased more than 12 months ago.
-Units purchased from unauthorized dealers or companies. Specifications MMRRFF--225500 Power Supply: 9V 300mA IR Flasher Line Outputs: 2.5mm Mono Mini Jack RF Frequency: 418MHz Size: 5 1/8 x 3.5 x 1.25 (4.5 antenna up) PPaaggee 1122 500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532