all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 2.23 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Test Report | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | Users Manual | Users Manual | 2.23 MiB |
Order Number Test Report Number
: GETEC-C1-09-209
: GETEC-E3-09-121 FCC Part 15 subpart C Page 1 / 1 APPENDIX I
: USERS MANUAL EUT Type: RF Remote Controller FCC ID.: OZ5URCRF20N 1 e t o m e R 0 2 F R e h T Congratulations!
Congratulations on purchas-
ing Universal Remote Controls MASTERCONTROL RF20 Pre-programmed and Learning Remote Control!
You now have the power to control your entire home entertainment system with one easy-to-use remote. The RF20 can be used with thousands of audio/video Components because of the extensive code library pre-programmed into the remote. And, the RF20s impressive lineup of special advanced features can automate and customize the operation of your system in many ways. So... get ready to sit back, relax and simplify your home entertainment experience. The Quick Setup DVD Program Guide supplied with the RF20 will assist you in programming your remote by guiding you through an easy step-by-step process. This Owners Manual is designed as a companion reference source to the DVD Guide, should you need to refer back to a particular section, or review certain instruction detail not covered in the DVD. However, if you are unable to watch the DVD Guide for some reason, everything you need to know about programming the RF20 is contained in this Manual. 500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 MASTERCONTROL RF20 Owners Manual 2006 Universal Remote Control, Inc. The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS /
OMISSIONS MADE IN THIS MANUAL. The information in this manual may be subject to change without prior notice. MASTERCONTROL, PowerBlaster, MacroPower, and SimpleSound are trademarks of Universal Remote Control, Inc. All other brand or product names are trademarks or registered trademarks of their respective companies or organizations. E M O C L E W LOCATION OF CONTROLS GETTING STARTED BASIC SETUP CUSTOMIZING YOUR RF20 WITH SPECIAL ADVANCED FEATURES ERASING COMMANDS THE OPTIONAL POWERBLASTERTM PREPROGRAMMED CODE NOTES PRE-
PROGRAMMED CODE TABLES OTHER INFO Keypad Layout Overview Battery Installation Activating Component Commands Light Button Overview Pre-Programmed Code Method Learning Method Transmitting (Busy Signal) Icon. Child Lock Feature Customizing the LCD Screen Favorite Channel Setup MacroPower Setup SimpleSound Setup &
Other 'Punch Throughs'
Setting Backlight Options Hiding & Adding Pages Recalling Pre-programmed Setup Code Numbers Cloning other RF20s Overview Erasing Learned Button, Macro or Favorite Channel Commands Re-setting RF20 to Original Factory Default Settings PowerBlasterTM Pre Programmed Code Notes Pre-Programmed Code Tables TV SAT CABLE CD DVD DVR VCR AUX AUDIO 45 48 50 53 55 FAQ Warranty Specifications Federal Communication Commission Interference Statement Warning FCC Caution 3 4 4 5 6 7 7 15 19 19 20 23 26 30 32 33 35 36 37 37 39 41 43 44 58 59 61 62 64 65 66 74 74 74 2 T h e R F 2 0 R e m o t e C O N T N E T S LIGHT BUTTON SCREEN-LABELED DISPLAY BUTTONS TITLE FAVORITE CHANNEL PAGE BUTTONS changes the page of buttons displayed PAGE NUMBERS MAIN BUTTON takes you to the main menu FUNCTION BUTTONS 3 t u o y a L d a p y e K I S N O T A C O L L O R T N O C Getting Started-Overview This is what MASTERCONTROL RF20 is all about!
The RF20 is designed to operate up to 10 different Audio/Video Components and is pre-programmed to operate virtually all brands of TV, VCR, DVD and CD Players, Cable Set Top Boxes, Satellite Receivers, TiVo and other DVRs, Audio Components, Tape Decks, Multimedia PCs, XM Radio, Ipod, X-Box, Lighting Controls and other custom installation products. It also offers an impressive lineup of special features designed to provide you with many time-saving conveniences and enhance your overall entertainment experience. However, we strongly recommend that you fully complete all of the Basic Setup steps before proceeding to customize your RF20 with any of the special advanced features. tell by the + (positive) and
- (negative) symbols. Once the batteries are correctly installed, replace the cover. Now youre ready to start!
Battery Installation The very first step is to insert the four AAA batteries that are included in the package into the battery compartment located in the back of the remote. Just press the tab and lift off the cover. Please be sure to insert the batteries correctly as you see in the diagram. Remember, there is a positive and negative end to each battery and you can 4 O v e r v i e w
B a t t e r y I n s t a l l a t i o n I G E T T N G S T A R T E D
) buttons on the MAIN menu and select the next Component you want to operate. If you dont see the Component you want to control on Page 1 of the MAIN menu, just use the PAGE (
left side of the screen to bring up Page 2 of the MAIN menu which displays an additional five Components. Activating Component Commands Simple, Easy, Intuitive Once youve programmed RF20 for your Components, all you have to do to operate a specific Component is first, press the MAIN but-
ton. This will display Page 1 of the MAIN menu on the LCD screen. Page 1 of the MAIN menu displays five Components. Then, simply select the Component you want to operate by pressing the corresponding Screen-
Labeled Component Display Button on the right side of the LCD Screen. As an example, if you press the TV Display Button, the display label at the top of the screen will change from MAIN to TV, and all the but-
tons on RF20 will work your TV. To operate another Component, simply press the MAIN button again to return to Page 1 of the Each Component is provided with five pages of pre-labeled command display buttons (or space for additional command display buttons). Once again, simply use the PAGE
the next command page, or return you to the previous command page.
) buttons to take you to
TV DEVICE BUTTON MAIN BUTTON 5 s d n a m m o C t n e n o p m o C g n i t a v i t c A D E T R A T S G N T T E G I 6 L I G H T B U T T O N Light Button The fully backlit keypad makes the RF20 easy to use in the dark or dim lighting conditions. Simply press the LIGHT button to backlight all the keypad buttons and LCD screen. To turn off the backlight, press the LIGHT button again, or just wait ten seconds (the backlight automatically shuts itself off). Lights out!
Try it out!
LIGHT BUTTON I G E T T N G S T A R T E D Basic Setup - Overview There are two ways to program the RF20:
The Pre-Programmed Code Method The Learning Method The Pre-Programmed Code Method allows you to set up all the buttons at once, so its the fastest and easiest of the two methods. The Learning Method allows you to transfer functions from other remotes (old or new), one button at a time. Pre-Programmed Code Method STEP 2:
Now, turn on the Component you want to program... lets say your TV to start. Look up your TVs manufacturer setup code from your reference list. STEP 1:
The pre-programmed 3-digit codes are found in the back of this Manual on page 45. The codes are listed by Component category (i.e., TV, VCR, DVD, etc.), then by brand name. For instance, if you want to locate a code for a Sony TV, first locate the TV category, and then look for the Sony brand. Once you have located the 3-digit code (or in some cases, several code numbers) for the Component that you want to operate with your RF20, write them ALL down on a piece of note paper. Its important that you write down all the codes because only one code is going to work for you. 7
w e i v r e v O d o h t e M e d o C d e m m a r g o r P
e r P P U T E S C S A B I 8 P r e
P r o g r a m m e d C o d e M e t h o d STEP 3:
Press and hold the MAIN and ENT
(Enter) buttons at the same time for approximately 3 seconds, until the word SETUP is displayed at the top of the LCD screen. This signals that you are now in setup mode. IMPORTANT:
You now have 30 seconds to perform the next step while you are in SETUP mode. If you dont press a button within 30 seconds, SETUP will disap-
pear from the screen, signaling that you have exited setup mode and you will need to start over. MAIN BUTTON ENTER BUTTON I B A S C S E T U P 9 d o h t e M e d o C d e m m a r g o r P
e r P STEP 4:
Press the P-PRO display button to select the Pre-Programmed Method. The screen will then display the five Components from Page 1 of the MAIN menu. To display Page 2 of the MAIN menu that lists an additional five Components, simply press the PAGE (
) buttons.
P-PRO BUTTON FIRST FIVE DEVICE NAMES PAGE BUTTONS P U T E S C S A B I 10 P r e
P r o g r a m m e d C o d e M e t h o d STEP 5:
Press the Component display button you want to program. For example: If you want to setup the TV Component button, press the TV Compo-
nent display button. The display at the bottom of the LCD screen will flash FROM - TABLE. STEP 6:
In this step you verify the type of component you plan to operate with this component button. For example: If you plan to operate the TV component with the TV button, simply press the TV display button once again. However, if for example you are setting up AUX to operate a second DVD Player, you would first need to press AUX in Step 5, and then DVD in Step 6. I B A S C S E T U P NOTE:
If the Component fails to turn off after you have entered all the code numbers listed for your brand, you can scan through all the other code numbers that are pre-loaded into the RF20 for that Component
(in this case TV) by using the UP or DOWN display buttons on the screen. (There is a chance that your Component was actually manufactured by another brand.) However, most of the code tables are so large that it is usually faster to use the Learning Method on Page 15. STEP 8:
When the Component turns off, press the ON button to turn the Component back on. Now you can test the Volume and Channel buttons (for TV), or PLAY and STOP (for VCR and DVD) to make sure they all work. If any of the buttons do not work properly, you need to find a new correct code. For UP & DOWN BUTTONS STEP 7:
Point the RF20 toward the Component you want to program, (in this example, TV), and punch in the 3-digit code that you wrote down for that specific Component. Use the Number buttons 0-9 on the remote to punch in the code. If the 3-digit code number that you just punched in is correct, the Component will turn off. If the Component does not turn off, continue entering code numbers from your list until the Component turns off. Some brands have several possible code numbers. NUMBER BUTTONS 11 d o h t e M e d o C d e m m a r g o r P
e r P P U T E S C S A B I 12 P r e
P r o g r a m m e d C o d e M e t h o d a example, maybe your Sony TV turned off with code number 147, but the volume controls did not work properly. If this is the case, try the next code number listed for that Component until you find a perfect match. ON BUTTON VOLUME BUTTONS CHANNEL BUTTONS PLAY BUTTON STOP BUTTON I B A S C S E T U P 13 d o h t e M e d o C d e m m a r g o r P
e r P STEP 9:
Once you have found the right code, save the code number by pressing the SAVE display button that appears on the LCD screen. The LCD screen will blink SAVED two times, signaling that the code number has been successfully saved. SAVE BUTTON P U T E S C S A B I 14 P r e
P r o g r a m m e d C o d e M e t h o d a STEP 10:
Exit SETUP mode by pressing the MAIN button two times. When the LCD screen displays MAIN, you are back in normal operating mode. NOW, PROGRAM THE REST OF YOUR COMPONENTS BY REPEATING STEPS 1 THROUGH 9. IN MOST SYSTEMS,YOU CAN FINISH BASIC SETUP IN JUST A FEW MINUTES AND PUT ALL YOUR OLD REMOTES AWAY. IF YOU ARE STILL MISSING COMMANDS TO CONTROL ANY OF YOUR COMPONENTS, USE THE LEARNING METHOD ON PAGE 15. MAIN BUTTON I B A S C S E T U P 15 d o h t e M g n i n r a e L Learning Method The RF20 can actually learn commands from other remote controls (old or new), one-button-at-a-time, so it will never become obsolete. RF20 is the last remote youll ever need!
Just follow these simple steps:
STEP 1:
Line-up the RF20 with the other remote control, head-to-head, one or two inches apart. STEP 2:
On the RF20, press and hold the MAIN and ENT (Enter) buttons at the same time for approximately three seconds, until the word SETUP is displayed at the top of the LCD screen. This signals you are now in SETUP mode. IMPORTANT You now have 30 seconds to perform the next step while you are in SETUP mode. If you dont press a button within 30 seconds, SETUP will disap-
pear from the screen, signaling that you have exited setup mode and you will need to start over. MAIN BUTTON ENTER BUTTON P U T E S C S A B I 16 L e a r n i n g M e t h o d STEP 3:
Press the LEARN display button on the LCD screen. The top of the screen will change to LEARN and display the five Components from Page 1 of the MAIN menu. STEP 4:
Select the Component you want to teach commands to by pressing that Component display button on the LCD screen (in this example, TV). The top of the TV screen will change to TV. To display Page 2 of the MAIN menu that lists an additional five Components, simply press the PAGE (
) buttons.
NOTE: If you want to teach any command to a Component button, press the desired Component display button once the top of the screen displays MAIN, by pressing the PAGE button.The top of the screen wil change to READY. Then go to STEP 6. LEARN BUTTON I B A S C S E T U P 17 d o h t e M g n i n r a e L STEP 5:
Press any button on the RF20 that you want to teach a com-
mand to. The top of the screen will change to READY and the bottom of the screen will display the button name you pressed. NOTE: If you don't see the display button you would like to teach on the LCD screen, use the PAGE
buttons you can't teach are the PAGE and MAIN buttons.
) buttons. The only
STEP 6:
Press and hold the button on the other remote control that you want to teach to the RF20 until the LCD display on the RF20 changes to either GOOD or FAILD. If the GOOD label appears on top of the display, you were successful. If the FAILD label appears on top of the display, try teaching the same button to the RF20 once again by repeating STEPS 5 and 6. P U T E S C S A B I STEP 7:
Now, continue to teach the RF20 any other commands from your other remotes by repeating STEPS 4 through 6 (to go back to STEP 4, simply press MAIN once). STEP 8:
Once you have completed teaching all the button commands to the RF20, return to normal operation by pressing the MAIN button twice. 18 L e a r n i n g M e t h o d I B A S C S E T U P NOTE: Test all your new commands. If any of them dont work, try the Learning Method again, following these suggestions:
Move to another room. Plasma TVs, sunlight, halogen or quartz lighting can interfere with the learning process. Even though the old remote seems to be working fine, put in fresh alkaline batteries. Gradually vary the distance between the remote controls. Try 1, 2 and so on, up to 4 feet. Try tapping the button on your old remote instead of pressing and holding it during the learning process. Some additional Information regarding the Learning Process:
Learned functions override any existing pre-programmed functions on the remote control. All buttons can be learned except for the PAGE, MAIN and LIGHT buttons. Learned functions are automatically erased when a new function is learned on the same button. Learned functions are retained even after a different Setup Code Number is programmed into the remote. To return to an original pre-programmed function, a learned function must be erased. 19 n o c I
) l a n g i S y s u B
g n i t t i m s n a r T Transmitting (Busy Signal) Icon When a command is being transmitted, an icon will appear in the upper right corner of the LCD screen. This indicates that a signal is being sent. This is particularly useful when setting up Macros and FAVs, since it flashes with every step of a sequence of commands. CHILD LOCK FEATURE This child-lock feature prevents the unauthorized use of the remote control by children. It blocks all operations of the remote control. To Activate:
Press the +10 and ENT (Enter) buttons simultaneously for 3 seconds. The bottom of the LCD will blink LOCKED three times and then display LOCKED. To Return to Normal Operation:
Press the +10 and ENT (Enter) buttons simultaneously again for 3 seconds. The LCD will display the last use mode. P U T E S C S A B I Customizing Your RF20 with Special Advanced Features After youve finished all your basic setup, you can choose to make operation easier by customizing the RF20 just the way you want, using the Special Advanced Setup Features described in this section. Customizing the LCD Screen You can easily edit or change the name of any of the display buttons (including Favorite Channels) on the LCD screen by following these steps:
STEP 1:
Press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 seconds, until the word SETUP is dis-
played at the top of the LCD screen. This signals that you are now in setup mode. IMPORTANT:You now have 30 seconds to perform the next step while you are in SETUP mode. If you dont press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. STEP 2:
Press the EDIT display button. The LCD display will change to the EDIT menu. STEP 3:
Press the TEXT display button. The screen will display the list of Components and EDIT will appear at the top of the screen. STEP 4:
Navigate to the Component and page where there is a button label you want to EDIT, selecting between the FAV, MAIN, COM-
PONENT display buttons; then using the PAGE button. NOTE: If you wish to change the name of
) a Component button, press the Page (
Up button twice.The top of the display will change to MAIN, and you can navi-
gate to MAIN page 1 or page 2 before going on to Step 5. 20 C u s t o m i z i n g t h e L C D S c r e e n C U S T O M Z N G I I 21 n e e r c S D C L e h t g n i z i m o t s u C I I G N Z M O T S U C STEP 5:
Press the button you wish to edit. The first character space of your button label will start to blink. UP CURSOR Button deletes all test LEFT CURSOR Moves blinking character left DOWN CURSOR deletes the currently blinking character RIGHT CURSOR Moves blinking character right BLINKING CHARACTER 22 C u s t o m i z i n g t h e L C D S c r e e n C U S T O M Z N G I I STEP 6:
Change the character by using any of the number keys. Each press of the same number button selects the next character of that numbers group, as shown in the diagram below. STEP 7:
Once the character you want appears, move to the next space by pressing the Right cursor button. STEP 8:
When you are finished editing the button, press the button you edited and SAVED will flash at the bottom of the display. To change any other button labels on the same Component, press the next button, then repeat steps 6-8. If you wish to edit a button on another Com-
ponent, press the MAIN button once, then repeat Steps 4-8. STEP 9:
Once youve finished editing buttons, press the MAIN button four times to return to normal operation. 23 p u t e S l e n n a h C e t i r o v a F Favorite Channel Setup This is one of RF20s most desirable features. Once its set up, you can select up to 40 favorite channels with the press of a button - without the need to remember or type in a channel number. Let the channel surfing begin!
To access Favorite Channel listings, simply press the FAV button to display Page 1 of Favorite Channel listings. There are eight pages of Favorite Channels, with five Channels on each page, for a total of 40 Channels. Just use the PAGE (
) buttons to locate the Channel you want to setup. Each
Channel can be setup to be instantly selected with the press of one button.
) To setup a Favorite Channel button, follow these steps:
STEP 2:
Press the FAV display button. The top of the display will show FAV. The bottom of the display will flash SELECT STEP 1:
Press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 seconds, until the word SETUP is displayed at the top of the LCD screen. This signals that you are now in setup mode. IMPORTANT:
You now have 30 seconds to perform the next step while you are in SETUP mode. If you dont press a button within 30 seconds, SETUP will disap-
pear from the screen, signaling that you have exited setup mode and you will need to start over. FAV BUTTON I I G N Z M O T S U C 24 F a v o r i t e C h a n n e l S e t u p C U S T O M Z N G I I STEP 5:
Press either the TV, SAT or CABLE Component button (select the Component you use to enter channel numbers). STEP 6:
Press each of the number buttons for the channel. Note: If a number is repeated when set-
ting the channel (for example, channel 33 or 522), it is usually best to set a half second delay in between the identi-
cal numbers by pressing the (II) PAUSE button. Each press of the PAUSE button increases the delay by a half second. PAUSE BUTTON NOTE: Some brands of television require an ENT (Enter) command after the channel numbers.
) buttons
STEP 3:
Use the PAGE (
until you locate the name
(i.e.,ABC, CBS, NBC) of the favorite channel you want to setup. STEP 4:
Press the favorite channel display button you want to setup. The top of the screen will change to show the channel name. The bottom of the screen displays STEP0, indicating that you have not entered the channel number yet. 25 p u t e S l e n n a h C e t i r o v a F I I G N Z M O T S U C STEP 7:
Press the LIGHT button after you enter the channel number. A new screen appears displaying SAVE, UNDO or EXIT. STEP 9:
When you are finished setting up Favorite Channel buttons, press the MAIN button twice to return to normal operation. STEP 8:
To save the channel you entered, press the SAVE display button. The UNDO display button lets you erase the last entry. The EXIT display button erases all entries for this button. SAVE BUTTON MacroPower Setup MacroPower is a unique feature that enables you to turn all of your Components ON or OFF, at the same time, simply with the press of one button. We call that a Macro. What would normally take multiple remotes and button pushes, the RF20 can accomplish with the press of one button. In addition to the Power ON or OFF buttons, any of the Display buttons (on any Component or Page) can be set to be Macro buttons as well. Feel the power!
To setup a Power ON macro button that will turn ON several components at the same time (for example, TV, VCR and CABLE), follow these easy steps:
STEP 4:
Press the first component dis-
play button you want the Macro to turn on (in this example, TV) and TV will display at the top of the screen and STEP 1 at the bottom. STEP 5:
Then, press the ON button to confirm the command and STEP 2 will display at the bottom of the screen. (NOTE: Whenever a button is pressed, another Macro step is counted and dis-
played at the bottom of the screen.) STEP 6:
Now, press the MAIN button to return to the Main Component listing. (STEP 3 will display at the bottom of the screen.) STEP 1:
Press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 seconds, until the word SETUP is displayed at the top of the LCD touch screen. This signals that you are now in setup mode. IMPORTANT: You now have 30 seconds to perform the next step while you are in SETUP mode. If you dont press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. STEP 2:
Press the MACRO display button on the LCD screen. The top of the screen will display MACRO. The bottom of the display will flash SELECT. STEP 3:
Press the ON button. ON will display at the top of the LCD screen. STEP0 will display at the bottom of the screen indicating that no macro steps have been entered yet. 26 M a c r o P o w e r S e t u p C U S T O M Z N G I I 27 p u t e S r e w o P o r c a M I I G N Z M O T S U C STEP 11:
Then, press the ON button to confirm the command. (STEP 8 will display at the bottom of the screen.) NOTE : Dont worry about the number of steps. Each macro button can store up to 190 steps, so you are not likely to run out of steps!
You can also program delays in between commands by pressing the (II) PAUSE button. Each press adds half a second to the delay. STEP 7:
Press the second component display button that you want the Macro to turn on (in this example, VCR) and VCR will display at the top of the screen. (STEP 4 will display at the bottom of the screen.) STEP 8:
Then, press the ON button to confirm the command. (STEP 5 will display at the bottom of the screen.) STEP 9:
Now, press the MAIN button to return to the Main Component listing. (STEP 6 will display at the bottom of the screen.) STEP 10:
Press the third component dis-
play button that you want the Macro to turn on (in this exam-
ple, CABLE) and CABLE will display at the top of the screen.
(STEP 7 will display at the bot-
tom of the screen.) 28 M a c r o P o w e r S e t u p C U S T O M Z N G I I STEP 12:
Press the LIGHT button to end your macro. A new screen will appear:
STEP 13:
If you are satisfied with your macro, press the SAVE display button. The UNDO display button lets you erase the last step. The EXIT display button erases all the macro steps. STEP 14:
Press the MAIN button twice to return to normal operation. SAVE BUTTON UNDO BUTTON EXIT BUTTON Advanced Macro Options:
SETTING UP A POWER OFF MACRO:
Simply follow the same steps as outlined above, except press the OFF button in place of the ON button. SETTING A COMPONENT BUTTON AS MACRO:
If you wish to set one of the Component buttons as a macro, in STEP 3, press the Page Up button twice. The top of the display will change to MAIN, and you can navigate to MAIN page 1 or page 2. Press the Component button you want to set as a Macro button. The top of the screen will display the button label you selected. Select the Component and Page that has a button you want in your Macro using the MAIN, Component and Page buttons. Simply press the button(s) with the command(s) you want in your Macro. Then complete and save the Macro by following STEPs 12 and 13 as outlined above. PROGRAMMING A PRESS & HOLD MACRO:
Another option for Component button macros is to only send the macro if the button is pressed and held. This is setup by entering a delay as the first step of the macro. The amount of delay determines how long the user must press the button before the macro is sent. The advantage of this option is that a normal press of the COMPONENT button will simply switch Components without sending the macro command. 29 p u t e S r e w o P o r c a M I I G N Z M O T S U C SimpleSound Setup & Other Punch Throughs SimpleSound is a dynamic feature that gives you total volume control over all the Components in your system, even those without their own built-in volume control, such as TiVo, DVD and VCR... saving you the hassle and inconvenience of constantly needing to switch between Component modes on the remote. With SimpleSound, you can set the RF20s volume control buttons to always control the sound in your system, even when youre in VCR or DVD mode, without switching back to AUDIO or TV. Even more exciting, SimpleSound is what is called a Punch Through feature and is not limited strictly to volume control. Click and enjoy!
STEP 1:
In a basic home entertainment system, the sound may come from your TV. In a more advanced system, the sound may come from your audio Component such as a Surround Sound Receiver or Home Theatre system. So, first, you need to identify which Com-
ponent you want to use in your system for sound. STEP 2:
Press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 seconds, until the word SETUP is dis-
played at the top of the LCD screen. This signals that you are now in setup mode.
) UP button to IMPORTANT:You now have 30 seconds to perform the next step while you are in SETUP mode. If you dont press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. STEP 3:
Press the PAGE (
display Page 2 of the Setup Menu on the LCD screen. Press the PUNCH display button. STEP 4:
Then press the VOL (Volume) display button. The screen will display VOL at the top. This sets up the group of three buttons (Volume Up, Volume Down and Mute) in one action!
VOLUME BUTTON 30 S i m p l e S o u n d S e t u p
O t h e r P u n c h T h r o u g h s C U S T O M Z N G I I 31
p u t e S d n u o S e l p m i S
s h g u o r h T h c n u P
r e h t O STEP 7:
Press the MAIN button twice to return to normal operating mode and test your SimpleSound settings. NOTE:The Punch Through feature is not limited to volume and can also be applied to channel selection or other functions. If you find yourself switching to a particular Component frequently to use a group of controls, consider using Punch Through for another group, as listed here:
VOL CH PLAY VOD Volume Up,Volume Down and Mute Channel Up, Channel Down, Previous Ch and Channel
(0-9) buttons. Play, Stop, Pause, Rewind and Fast Forward Guide, Menu, Info, Exit, Up, Down, Left, Right, Select Simply perform the steps outlined above, but in STEP 4, press one of the control options (CH, PLAY or VOD). The bottom of the display flashes PUNCH TO. Press the button for the Component that doesnt have volume control commands yet (i.e.,DVD). This is the Com-
ponent you are going to PUNCH TO for the volume and mute commands. NOTE: If you want to PUNCH TO the MAIN Component, press the POWER OFF button at this time. STEP 5:
The bottom of the display will then flash PUNCH FROM. Now select the Component that has the volume commands you want to use (i.e.,TV for systems using the TV speakers, AUDIO for sys-
tems with surround sound receivers). The bottom of the dis-
play will flash SAVED. STEP 6:
Repeat STEPS 4-5 until all your Components operate the volume perfectly. I I G N Z M O T S U C 32 S e t t i n g B a c k l i g h t O p t i o n s Setting Backlight Options You can customize the backlighting feature to suit your specific preferences by following these simple steps:
Adjusting Length of Backlight Time You can adjust the amount of time that the RF20 backlight stays on by entering the SETUP mode and proceeding to
) UP button), then pressing the page 2 (using the PAGE (
LIGHT display button on the LCD screen (not the Backlight button). Then enter the amount of time you would like the light to stay on using the number pad (0-99 seconds). After making your selection, press the SAVE display button. Adjusting Contrast You can make the text darker by pressing both the MAIN and cursor UP buttons at the same time. To make the text appear lighter, press both the MAIN and cursor DOWN buttons at the same time. Turning OFF Backlighting If you dont want backlighting at all (this extends battery life), press the ON display button that appears on the screen. The ON will change to OFF. Press the SAVE display button. Exit the setup mode by pressing the MAIN button. MAIN BUTTON UP & DOWN CURSOR HIGH CONTRAST LOW CONTRAST C U S T O M Z N G I I Hiding and Adding Pages Each of your RF20 Components actually contains eight pages. However, only five pages are visible in the factory default setting. Three page are hidden in each Component. If you wish to use the hidden pages, you can ADD it. If you dont want to use some of the existing pages, you can HIDE them. You can add or hide pages on Components OR on your favorite channel pages using this simple process:
NOTE: Be sure to program your Macros before you hide pages with potential macros in them. You cant access hidden pages during macro setup. However, after you finish Macro setup, you can hide pages without affecting operation of your macros. STEP 2:
Press the EDIT display button on the LCD screen. STEP 3:
Press the PAGE display button once the screen changes to EDIT mode. STEP 1:
Press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 seconds, until the word SETUP is dis-
played at the top of the LCD screen. This signals that you are now in setup mode. IMPORTANT:You now have 30 seconds to perform the next step while you are in SETUP mode. If you dont press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. EDIT BUTTON PAGE BUTTON 33 s e g a P g n i d d A d n a g n i d i H I I G N Z M O T S U C 34 H i d i n g a n d A d d i n g P a g e s This page is hidden. To ADD it, press the LIGHT button. This page is visible.To HIDE it, press the LIGHT button. STEP 4:
PAGE appears at the top of the screen. Now, you can navigate to any page, using the MAIN, COMPONENT, FAV, and PAGE display but-
tons. PAGE BUTTON FAV BUTTON COMPONENT BUTTONS MAIN BUTTON STEP 5:
When you select a page, the top of the screen indicates whether you want to ADD? or HIDE?
the page displayed. When you want to change a pages visibility
(i.e., either ADD or HIDE), simply press the LIGHT button. STEP 6:
You can continue to ADD or HIDE pages on other Components by repeating Steps 4 and 5. STEP 7:
When you are finished adding and hiding pages, press the MAIN button four times to return to normal operation. C U S T O M Z N G I I 35 s r e b m u N e d o C p u t e S d e m m a r g o r P
e r P g n i l l a c e R I I G N Z M O T S U C Recalling Pre-Programmed Setup Code Numbers In case you didnt write down the Pre-Programmed Code Numbers that you used to set up your RF20, you can easily recall them using this simple process:
STEP 4:
Write down the code numbers as they appear for future refer-
ence. Page 43 of this manual provides a convenient space for you to record your code numbers. STEP 5:
Return to normal operation by pressing the MAIN button twice. STEP 1:
Press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 seconds, until the word SETUP is displayed at the top of the LCD touch screen. This signals that you are now in setup mode. IMPORTANT:You now have 30 seconds to perform the next step while you are in SETUP mode. If you dont press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. STEP 2:
Go to Page 2 of the Setup Menu by pressing the PAGE (
) button. STEP 3:
Press the RECAL display button on the LCD screen. The display will change to the Recall screens. The screen automati-
cally switches between four screens, alternately flashing Page 1 components and code numbers, then Page 2 compo-
nents and code numbers. Cloning Other RF20s If you are fortunate enough to own more than one RF20, youll be happy to know that you can easily copy and trans-
fer all the setup from one RF20 to another. Just follow these easy steps:
36 C l o n i n g O t h e r R F 2 0 s STEP 1:
For both the programmed RF20 that you want to clone, and unprogrammed RF20, press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 seconds, until the word SETUP is displayed at the top of their respective LCD screens. This signals that both remotes are now in setup mode. IMPORTANT:You now have 30 seconds to perform the next step while you are in SETUP mode. If you dont press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. STEP 2:
Press a PAGE button on each remote to bring up Page 2 of Setup and display the CLONE button. STEP 3:
Press the CLONE button on each remote. STEP 4:
Align the two RF20s head-to-
head, about an inch apart. STEP 5:
Press the RECV display button on the unprogrammed RF20 that you want to setup by cloning. STEP 6:
Press the SEND display button on the programmed RF20 that you want to clone. STEP 7:
Press the START button on the unprogrammed RF20, and then press the START button on the programmed RF20 that you want to clone. NOTE: Cloning typically takes about 40 seconds. After successful cloning is com-
pleted, the newly cloned RF20 will flash GOOD. STEP 8:
Return to normal operation by pressing the MAIN button twice. C U S T O M Z N G I I 37 r o s o r c a M
, s n o t t u B d e n r a e L g n i s a r E s l e n n a h C e t i r o v a F Erasing Commands - Overview You can erase an individual button with a learned com-
mand, a macro or a favorite channel. You can erase an ENTIRE Components learned command or macro buttons. You can also erase ALL your learned commands on all Components or all your macros or favorite channels every-
where. If you really want a fresh start, it is possible to reset every-
thing to the factory default settings. Erasing Learned Buttons, Macros or Favorite Channels STEP 1:
Press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 sec-
onds, until the word SETUP is displayed at the top of the LCD screen. This signals that you are now in setup mode. IMPORTANT:You now have 30 seconds to perform the next step while you are in SETUP mode. If you dont press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. STEP 2:
Press a PAGE button to display Page 2 of Setup. STEP 3:
Press the ERASE display button on the LCD screen. STEP 4:
Press either the LEARN, MACRO or FAV button. The following screen appears:
ALL - Erases ALL of the speci-
fied (Learned, Macro or FAV but-
tons everywhere in the RF20) DEVICE - Erases all learned or Macro buttons in a single Component (NOTE: This option is not available for FAVs.) KEY - Erases one button only. S D N A M M O C G N S A R E I 38 E r a s i n g L e a r n e d B u t t o n s
, M a c r o s o r F a v o r i t e C h a n n e l s STEP6:
To return to normal operating mode, press the MAIN button four times. I E R A S N G C O M M A N D S STEP 5:
If you press ALL, the RF20 dis-
plays a SURE? button. After the SURE button is pressed, all the buttons will be erased. If you press DEVICE, a list of Components will appear. Press the Component button that you wish to erase. The bottom of the screen will flash ERASE twice, then ERASED. If you press KEY, youll have to navigate to the Component and Page you want using the MAIN, COMPONENT and PAGE buttons. Press a button to erase it. The bottom of the display will flash ERASE twice, then ERASED. SURE BUTTON Re-setting RF20 to Original Factory Default Settings If you want to start with a clean slate, you can re-set the RF20 its original factory default settings by performing the following steps. NOTE: This process will essentially erase EVERYTHING you have programmed into the RF20. STEP 1:
Press and hold both the MAIN and the STOP buttons for 10 seconds. STEP 2:
After 10 seconds, the RESET screen appears. Press the ALL button. The RF20 will display a SURE? button. Press the SURE button to erase all of your settings and return to the factory default setup MAIN BUTTON STOP BUTTON SURE BUTTON 39 s g n i t t e S t l u a f e D y r o t c a F l a n i g i r O o t 0 2 F R g n i t t e s
e R S D N A M M O C G N S A R E I 40 F a c t o r y D e f a u l t S e t t i n g s R e
s e t t i n g R F 2 0 t o O r i g i n a l I E R A S N G C O M M A N D S The Optional PowerBlasterTM
(for barrier-free RF control)
[Sold separately]
Of all the fabulous RF20 features, this is probably the most exciting. When used in combination with the optional PowerBlasterTM, the RF20 becomes an amazing remote control powerhouse that sends multi-directional RF (Radio Frequency) signals that pass through walls, doors and floors - both indoors and outdoors. This changes everything! It enables you to control Components that are completely out-of-sight, up to 100 away. The PowerBlasterTM picks up RF20s radio frequency signals from any direction, regardless of distance, so RF20 doesnt need to be pointed directly at any Component. Just imagine - no more pointing! Now you can close your entertainment center doors, hide your Components, and still control them with ease. Control outdoor speakers on your patio. Control your Components anywhere!
One of the best things about this is -- nothing has to be done to the RF20 for this feature to work. Every time you press a button on the RF20, it sends both a standard IR (Infrared Command) AND an RF (Radio Fre-quen-
cy) signal. If you install the PowerBlasterTM kit, it will automat-
ically receive RF20s radio signals and translate them into the infrared commands that control your Components. NOTE: The RF20's radio signals will not control Components directly. You must have a PowerBlasterTM to receive the RF20's radio signals. Components that came with "no point-
ing" radio remote controls cannot be operated by the RF20 unless the Component can be switched to standard IR
(Infrared Control) via its internal menus. Some remote con-
trol ceiling fans are radio only and cannot be operated by the RF20. 41 l o r t n o c F R e e r F
r e i r r a B R E T S A L B R E W O P E H T The RF20 sends radio signal to the PowerBlasterTM, which is a radio receiver 42 B a r r i e r
F r e e R F c o n t r o l The PowerBlasterTM converts radio signals to standard infrared commands and sends them out via a built-in front blaster to Components in the same cabinet space. T H E P O W E R B L A S T E R Self-adhesive flashers (included in the PowerBlasterTM kit) affix to the front panels of your Components. The flashers relay infrared commands to Components out-of-
sight of the PowerBlasters front blaster. The flashers plug into PowerBlasters rear flasher line output jacks. Each flasher has a 10 cable to easily reach Components on nearby shelves. Pre-Programmed Code Notes Record the three digit codes for your system here AUDIO DVD CD SAT TV VCR CABLE AUX LIGHT TAPE PHONO TV2 VCR2 DVR LDP XM RADIO IPOD X-BOX 43 s e t o N e d o C d e m m a r g o r P
e r P S E T O N E D O C D E M M A R G O R P E R P
Pre-Programmed Code Tables The RF20s Pre-Programmed code library is divided into cate-
gories (TV, VCR, AUX, etc.). Each category actually includes many types of Components. For example, the VCR category includes TV/VCR combo units. Within each category, the code numbers are listed in rows by brand (Sony, Panasonic, B & K, etc.). Some brands have more than one three digit code for you to try. Just circle the correct row and refer to it while you setup (step by step instructions for using Pre-Programmed codes are found on page 7). TV TVs, Plasmas, Projectors and Monitors CABLE Cable TVs and Web TVs DVD VCR DVD Players and TV/DVD Combos VCRs and TV/VCR Combos AUDIO Amps, Preamps, A/V Receivers and XM Radios SAT CD DVR AUX Satellite Receivers CD Players and CD Changers TiVo, Replay and other DVRs Tape Decks, Lighting Controls, Multimedia PCs, Xbox, iPod and Custom Installation Products 44 P r e
P r o g r a m m e d C o d e T a b l e s
P R E P R O G R A M M E D C O D E T A B L E S 45 BRAND V T S E L B A T E D O C ADMIRAL ADVENT AKAI A MARK AMPRO AMSTRAD ANAM AOC APEX DIGITAL AUDIOVOX BARCO BLAUPUNKT BROKSONIC CAIRN CANDLE CAPEHART CETRONIC CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROWN CURTIS MATHES CXC DAEWOO DAYTRON DELL DREAMVISION DWIN DYNASTY DYNATECH EIKI ELECTROHOME EMERSON EPSON ESA FISHER FUJITSU FUNAI FUTURETECH GATEWAY GE GEM GOLDSTAR HALL MARK HANNSPREE HITACHI HP HYUNDAI INFINITY INFOCUS INSIGNIA JBL JCPENNEY JENSEN JVC CODE NUMBERS 072 081 161 160 247 197 146 248 404 405 112 143 167 073 157 183 052 043 054 056 080 112 131 197 004 112 058 006 310 076 273 233 088 238 201 197 002 003 004 058 043 197 002 003 004 043 101 103 143 043 004 043 050 051 143 043 054 043 143 197 101 004 143 043 004 016 043 044 076 103 114 125 127 143 004 143 320 319 321 235 345 177 257 043 062 187 143 024 076 196 028 048 043 155 005 197 004 047 050 051 076 096 143 151 153 154 324 323 007 057 246 198 346 028 043 043 242 268 160 144 165 073 197 008 009 034 056 074 130 155 161 004 091 157 183 387 113 116 102 004 106 112 119 127 143 004 381 011 163 166 004 009 010 012 023 075 143 158 072 378 316 327 337 338 164 333 230 330 350 399 403 052 164 164 004 024 197 008 009 030 065 101 143 156 160 013 038 034 070 083 145 199 210 240 241 BRAND KEC KENWOOD KLOSS KMC KTV LG LODGENET LOEWE LOGIK LUXMAN LXI MAGNAVOX MARANTZ MATSUI MAXENT MEMOREX METZ MGA MINERVA MINTEK MITSUBISHI MTC NAD NEC NIKEI NUVISION ONKING ONWA OPTOMA OPTONICA ORION PANASONIC PHILCO PHILIPS PIONEER POLAROID PORTLAND PROSCAN PROTON PROTRON QUASAR RADIO SHACK RCA REALISTIC ROCTEC RUNCO SAMPO SAMSUNG SANYO SCEPTRE SCOTT SEARS SELECO SHARP SIEMENS SIM2 SIGNATURE SOLE SONY CODE NUMBERS 043 197 070 002 059 143 043 197 143 154 363 113 116 102 004 106 112 119 127 143 243 284 365 072 164 072 004 166 007 015 052 081 160 164 164 059 197 003 060 061 004 063 064 127 022 160 094 239 226 273 390 197 164 184 164 242 007 072 004 088 197 004 024 028 042 088 362 124 109 024 004 028 040 042 146 191 197 004 062 101 015 025 272 132 130 134 197 040 016 024 056 019 236 262 043 351 043 043 265 270 019 081 096 080 034 056 092 164 208 197 003 059 060 064 164 004 024 056 063 164 005 093 038 197 003 004 059 127 184 206 239 259 335 135 025 197 018 023 116 393 272 138 268 328 353 354 356 388 004 143 144 160 161 165 167 004 131 058 143 171 173 193 392 398 034 056 092 019 004 143 043 127 333 160 165 065 156 144 161 197 004 024 056 152 023 074 007 019 043 047 186 168 169 178 179 180 181 182 183 073 157 340 395 197 058 004 202 258 050 089 101 105 004 127 143 160 228 229 166 007 020 053 057 082 187 276 028 043 004 048 143 015 030 004 007 028 057 143 094 160 082 165 166 189 200 205 227 251 081 019 014 170 028 029 004 022 143 175 088 189 200 205 227 072 231 232 277 070 139 147 126 185 194 085 213 279 46 T V C O D E T A B L E S 47 BRAND V T SOUNDESIGN SPECTRICON SSS SUPRE MACY SVA SYLVANIA SYNTAX OLEVIA TANDY TATUNG TECHNICS TECHWOOD TEKNIKA TELEFUNKEN TELERENT TERA TMK TOSHIBA TOTEVISION UNIVERSAL VIDEO CONCEPTS VIDIKRON VIDTECH VIEWSONIC VIZIO WARDS WESTING HOUSE WINBOOK YAMAHA YORK YUPITERU ZENITH ZONDA CODE NUMBERS 028 004 003 043 112 004 043 002 328 197 003 059 060 063 064 164 044 160 127 376 363 081 056 062 034 080 004 002 003 004 024 028 043 072 101 143 037 046 086 087 072 172 004 138 015 030 007 040 062 101 325 143 008 009 146 174 184 188 192 340 004 242 389 390 386 387 004 008 009 019 028 060 061 063 064 072 074 143 164 034 076 280 339 197 004 004 043 073 072 095 103 157 183 243 284 112 S E L B A T E D O C CODE NUMBERS 004 103 003 039 042 046 053 043 074 043 043 099 005 007 014 074 074 043 074 099 043 074 074 043 110 074 043 074 108 092 007 043 074 007 074 080 081 043 074 110 074 043 074 101 020 030 040 057 066 106 032 008 054 BRAND ABC ADELPHIA ADVANCED NEWHOUSE ALTRIO AMERICAST ARCHER ARMSTONG AT&T BROADBAND ATLANTIC BROADBAND BELL SOUTH BLUE RIDGE BRESNAN BRIGHT HOUSE BUCKEYE COMM CABLEVISION CENTURION CENTURY CHARTER CITIZEN COGECO COMBANO COMCAST COMSAT COX DIGITAL DIGICABLE EAGLE EASTERN ECHOSTAR ELECTRICORD GEMINI GENERAL ELECTRIC 072 074 103 104 GENERAL INSTRUMENT GNC 099 GOLDEN CHANNEL 030 HAMLIN HITACHI INSIGHT JERROLD MAGNAVOX MASSILLON MEDIA ONE MEDICOM MEMOREX MITSUBISHI MOTOROLA MOVIE TIME MOXI NCTC NSC OAK PACE PANASONIC PARAGON PHILIPS PIONEER PRUCER PULSAR RCA RCN RECOTON 049 050 055 103 055 074 074 004 103 002 003 008 009 010 069 010 012 064 079 095 094 074 107 074 052 102 074 110 109 111 028 032 111 074 015 028 038 071 031 037 053 043 074 044 047 052 006 012 013 020 085 095 043 103 034 051 063 076 105 059 052 047 074 098 48 C A B L E
W E B T V C O D E T A B L E S 49 BRAND CODE NUMBERS 049 050 057 043 030 REGAL REGENCY RODGERS SAMSUNG SCIENTIFIC ATLANTA 043 011 003 041 042 045 046 SEREN SERVICE ELECTRIC SHAW SIGECOM SONY SPRUCER STARCOM STARGATE SUSQUEHANNA TIME WARNER TOCOM TOSHIBA UNITED CABLE UNIVERSAL VIDEOTRON VIEWSTAR WIDE OPEN WEST ZENITH 043 074 074 043 096 108 047 078 002 004 008 009 008 030 097 104 043 074 043 074 039 040 056 052 004 053 005 007 014 032 035 043 012 015 018 086 087 088 089 043 099 052 060 093 100 V T B E W
E L B A C S E L B A T E D O C BRAND AIWA AKAI ALPINE APEX DIGITAL ARCAM CAMBRIDGE AUDIO CARY AUDIO DESIGN CLASSE COBY DENON FUNAI GATEWAT GE GO VIDEO HARMAN KARDON HITACHI ILO INSIGNIA INTEGRA JVC KENWOOD KLH KISS KRELL LEXICON LG LITEON MAGNAVOX MALATA MARANTZ MERIDIAN MITSUBISHI MYRYAD NAD NAKAMICHI ONKYO OPPO PANASONIC PHILIPS PIONEER POLAROID PRIMARE PROCEED PROSCAN RCA RJTECH ROTEL SAMSUNG SANSUI SANYO SENSORY SCIENCE SHARP SONY SYLVANIA SYMPHONIC TAG MCLAREN TATUNG TEAC THOMPSON THULE CODE NUMBERS 146 281 098 087 111 115 112 116 122 215 174 167 258 007 080 173 143 175 026 027 137 218 220 221 222 084 140 101 268 143 142 180 012 151 135 179 279 104 148 091 057 074 264 265 066 096 143 267 083 095 153 017 102 134 088 155 103 076 035 180 266 021 042 138 139 144 150 066 083 095 105 166 023 092 099 107 108 131 233 234 237 193 194 086 026 027 026 027 269 204 056 070 119 165 170 137 159 154 147 222 223 094 033 118 145 126 191 143 143 156 102 270 026 027 177 50 D V D C O D E T A B L E S 51 BRAND D V D TOSHIBA VENTURER VINC YAMAHA ZENITH CODE NUMBERS 035 034 130 141 164 188 273 149 161 042 089 166 195 197 057 074 091 DVD-TV/DVD Combos AIWA AKAI FUNAI INSIGNIA SAMSUNG SYLVANIA SYMPHONIC TOSHIBA DVD-TV/DVD/VCR Combos MAGNAVOX PANASONIC SYLVANIA TOSHIBA DVD-DVD/VCR Combos GO VIDEO PANASONIC PHILIPS POLAROID SAMSUNG SANSUI SONY TOSHIBA ZENITH DVD-DVD Recorders GATEWAY GO VIDEO ILO KISS LITEON PANASONIC SENSORY SCIENCE SONY TOSHIBA DVD-DVD-LD DENON FUNAI KENWOOD MAGNAVOX MARANTZ MITSUBISHI NAD OPTIMUS PANASONIC PHILIPS PIONEER RADIO SHACK RCA REALISTIC RUNCO S E L B A T E D O C 146 281 143 143 165 143 143 130 143 144 143 164 137 218 150 105 (VCR Functions for VCR 067) 234 137 159 154 145 141 091 (VCR Functions for VCR171) 175 220 221 222 268 279 265 139 222 191 188 206 207 120 152 013 032 121 211 121 121 049 013 113 032 106 117 121 120 002 049 127 CODE NUMBERS BRAND SANYO SHARP SONY TECHNICS THETA DIGITAL TOSHIBA YAMAHA 075 152 013 053 110 113 032 152 106 043 129 52 D V D C O D E T A B L E S 53 BRAND CODE NUMBERS R C V S E L B A T E D O C 034 161 016 146 043 046 124 125 142 072 031 AIWA AKAI AMPRO ANAM AUDIO DYNAMICS 012 023 039 043 BROOKSONIC CANON CAPEHART CRAIG CURTIS MATHES DAEWOO DAYTRON DBX DYNATECH ELECTROHOME EMERSON 035 037 129 028 031 108 003 040 135 031 041 111 116 117 119 005 007 010 065 108 110 112 108 012 023 039 043 034 053 059 006 029 035 017 025 027 031 034 036 037 046 101 129 131 138 153 162 116 003 010 008 009 034 031 072 147 063 107 109 144 132 136 155 040 115 101 106 114 013 020 012 123 FISHER FUNAI GE GO VIDEO GOLDSTAR HARMAN KARDON 012 045 HITACHI INSTANTREPLAY JCL JCPENNEY JENSEN JVC KENWOOD LG LLOYD LXI MAGIN MAGNAVOX MARANTZ MARTA MATSUI MEI MEMOREX MGA MINOLTA MITSUBISHI MTC MULTITECH NEC NORDMENDE OPTONICA ORION PANASONIC PENTAX PHILCO PHILIPS PILOT PIONEER PORTLAND PULSAR QUARTZ QUASAR RADIO SHACK 004 026 150 018 034 043 063 137 160 013 031 031 012 013 015 040 066 101 043 048 043 130 150 055 060 012 031 050 152 166 014 048 034 047 101 106 114 013 020 012 123 034 034 003 009 017 106 040 067 031 034 068 041 156 164 067 069 012 031 156 101 027 030 031 101 003 010 014 031 034 053 072 102 134 139 045 046 059 013 020 059 061 151 013 020 045 046 051 142 049 168 034 040 024 034 012 023 039 043 048 043 053 054 025 066 070 145 083 133 140 157 163 074 167 013 020 031 063 031 034 067 031 067 034 101 054 071 156 101 021 013 048 108 072 002 014 066 145 075 123 CODE NUMBERS BRAND 107 109 144 147 158 041 145 013 020 140 034 040 RCA 003 008 010 014 031 034 040 053 054 101 REALISTIC 058 RICO 148 RUNCO 014 SALORA 102 104 113 115 112 120 032 040 066 107 109 122 125 SAMSUNG 022 043 048 135 SANSUI 003 010 007 014 134 102 SANYO 017 037 112 129 131 SCOTT 003 008 010 014 081 013 101 009 017 073 112 SEARS 149 054 031 159 165 SHARP 024 SHINTOM 034 SIGNATURE 056 057 058 077 052 003 078 076 031 149 154 SONY 034 SOUNDESIGN 013 STS 031 034 059 067 SYLVANIA 034 SYMPHONIC 010 034 TANDY 039 043 TATUNG 034 039 043 TEAC 031 070 TECHNICS 031 019 034 101 TEKNIKA 034 THOMAS 006 TMK 112 131 079 008 059 047 082 013 042 081 TOSHIBA 040 101 TOTEVISION UNITECH 040 VECTOR RESEARCH 012 048 VICTOR 012 034 046 141 VIDEO CONCEPTS 040 VIDEOSONIC 003 013 017 024 031 034 040 053 054 131 WARDS YAMAHA 012 034 039 043 072 080 056 048 101 034 058 ZENITH VCR-TV/VCR Combos DAEWOO EMERSON FUNAI GOLDSTAR HITACHI JCPENNEY LG LLOYD MAGNAVOX MEMOREX PANASONIC PHILIPS RADIO SHACK RCA SEARS SONY SYLVANIA SYMPHONIC THOMAS ZENITH 005 117 153 034 101 123 034 101 101 123 034 034 067 101 070 167 034 067 123 034 101 057 154 067 034 034 034 54 V C R C O D E T A B L E S 55 BRAND CODE NUMBERS O I D U A S E L B A T E D O C ADC ADCOM AIWA AKAI AMC AMEND AMX ANGSTROM ANTHEM ARCAM ATLANTIC TECHNOLOGY AUDIO ACCESS AUDIO ALCHEMY AUDIO DESIGN AUDIO EASE AUDIO FILE AUDIO MATRIX AUDIO SOURCE AUDIO TECHNICA B & K BOSE BOSTON ACOUSTICS BRYSTON CAMBRIDGE AUDIO CARVER CASIO CHIRO CINEMA SOUND CITATION CLARION CLASSE COMPAQ CURTIS MATHES DELPHI DENON 007 082 092 225 161 269 355 356 366 170 018 104 202 203 213 211 188 138 189 125 126 127 128 258 281 282 038 054 196 142 335 336 337 338 339 141 418 419 342 147 135 194 221 011 021 196 207 071 167 273 134 096 097 070 170 224 347 409 459 460 532 447 023 522 006 028 061 071 201 214 226 180 185 022 029 077 284 076 140 034 134 148 272 026 537 382 076 415 515 002 034 109 215 229 230 027 037 234 259 330 340 341 349 350 400 401 402 444 564 466 EAD 149 EIGER ELAN 057 290 ENLIGHTENED AUDIO 099 098 ESCIENT FANFARE FISHER FLEXTRONICS FOSGATE FOSGATE AUDIONICS GE GOLDSTAR HAFLER HARMAN KARDON 231 233 254 153 154 118 121 227 277 317 318 365 HITACHI IMERGE INKEL INSIGNIA INTEGRA JAMO JBL JCPENNEY JEFF ROWLAND JENSEN 368 381 451 452 453 454 352 047 214 180 182 297 378 062 231 342 056 260 008 174 020 371 197 589 354 438 398 263 076 216 206 058 BRAND JVC KENWOOD KINERGETICS KLH KOSS KRELL KYOCERA LEXICON LINN LUXMAN LXI MAGNAVOX MARANTZ MCINTOSH MCS MERIDIAN MITSUBISHI MONDIAL MYRYAD NAD NAKAMICHI NEC NIRO NILES ONKYO OPTIMUS OUTLAW PANASONIC PARASOUND PHAST PHILIPS PIONEER POLKAUDIO PRIMARE PROCEED RCA REALISTIC REQUEST REVOX ROTEL RUSSOUND SAMSUNG SANSUI SANYO SCOTT SEARS SHARP SHERWOOD SIRIUS SONY SOUNDESIGN SOUNDMATTERS SOUNDSTREAM SSI SUMO SUNFIRE TAEKWANG TEAC CODE NUMBERS 240 163 191 114 266 279 291 026 066 145 146 181 190 197 192 182 199 151 222 180 005 280 374 550 220 140 331 216 573 150 072 376 384 007 120 235 236 237 357 358 359 360 361 362 363 364 124 377 137 139 052 165 115 004 009 076 056 086 164 152 208 006 028 031 040 063 185 186 251 265 119 289 296 492 238 286 076 100 012 013 242 243 204 157 158 042 043 081 112 276 293 186 113 283 478 479 111 244 245 172 183 287 176 343 403 017 046 064 107 108 187 079 080 090 179 209 270 275 438 026 041 138 342 032 195 219 177 292 383 516 129 130 132 261 294 295 333 334 196 249 250 251 063 119 014 033 039 044 045 050 069 159 168 116 035 078 198 480 029 515 464 144 268 010 048 117 156 067 288 019 056 073 075 095 351 162 074 083 085 379 391 392 016 571 040 048 110 119 065 228 047 059 019 091 076 026 094 131 175 181 024 038 055 102 103 105 106 051 030 447 585 018 093 223 247 248 160 166 015 101 184 218 271 353 369 372 380 417 421 036 375 084 088 068 171 344 345 346 494 138 005 019 049 111 212 217 56 A U D I O C O D E T A B L E S 57 BRAND O I D U A TECHNICS THETA DIGITAL TOSHIBA WARDS XM SATELLITE RADIO YAMAHA ZENITH AUDIO-XM Radios & Tuners BOSE DELPHI FANFARE KENWOOD POLKAUDIO SIRIUS SONY XM SATELLITE RADIO CODE NUMBERS 122 176 193 219 178 177 200 257 262 136 060 087 198 278 180 415 515 026 253 169 067 173 205 264 232 089 264 274 285 332 373 432 433 143 210 170 532 415 515 352 550 515 585 380 415 515 S E L B A T E D O C BRAND CABLEVISION / VOOM DIRECTV ECHOSTAR / DISH EXPRESSVU GENERAL ELECTRIC GENERAL INSTRUMENT GOI HITACHI HTS HUGHES JVC LG MAGNAVOX MEMOREX MITSUBISHI MOTOROLA NEXT LEVEL PANASONIC PANSAT PAYSAT PHILIPS PROSCAN RADIOSHACK RCA SAMSUNG SKY SONY STAR CHOICE TOSHIBA UNIDEN ZENITH CODE NUMBERS 148 173 122 167 168 122 151 106 150 148 122 139 140 122 161 162 068 154 165 166 108 117 122 170 136 136 068 154 148 148 142 160 172 136 152 153 156 068 154 136 108 117 151 106 150 148 151 106 150 123 155 163 169 175 164 103 148 127 068 154 157 158 136 159 58 S A T C O D E T A B L E S 59 BRAND CODE NUMBERS D C S E L B A T E D O C 062 042 ADCOM 059 065 088 089 105 122 170 187 AIWA 085 195 202 AKAI 231 232 AMC 118 AMEND 238 ARCAM 119 147 AUDIO ACCESS 165 AUDIO EASE 046 AUDIO TECHNICA BSR 037 057 CALIFORNIA AUDIO 103 008 CAPETRONIC CARRERA CARVER 063 057 080 185 041 044 050 086 107 130 134 135 138 139 203 204 167 111 182 182 159 035 002 123 042 069 102 050 185 134 008 111 010 069 102 080 093 CASIO CLARINETTE CREEK CROWN DENON EMERSON FISHER FRABA GENEXXA GOLDSTAR HAITAI HARMAN KARDON 018 033 047 208 HITACHI INKEL JCPENNEY JENSEN JVC KENWOOD KOSS KRELL KYOCERA LOTTE LUXMAN LXI MAGNAVOX MARANTZ MCINTOSH MCS MEMOREX MISSION MITSUBISHI MITSUMI MODULAIRE MONDIAL MYRYAD NAD NAKAMICHI NEC NIKKO NSM ONKYO OPTIMUS PANASONIC PARASOUND PHILIPS 042 175 130 143 144 014 061 092 141 158 004 022 136 163 213 214 242 243 185 007 023 055 071 072 142 137 254 061 241 005 102 011 028 070 076 249 252 059 044 107 027 041 044 051 077 107 209 246 212 247 014 073 092 010 044 107 179 153 182 147 244 155 006 005 067 178 217 218 219 095 014 062 046 044 107 030 038 039 168 169 010 050 057 058 081 082 083 085 093 195 103 201 172 008 068 248 233 240 041 044 107 246 253 CODE NUMBERS BRAND PIONEER PROCEED PROTON QUASAR RADIO SHACK RCA REALISTIC ROTEL SAE SANSUI SANYO SCOTT SHARP SHERWOOD SIGNATURE SONY SOUNDESIGN SUMO SYLVANIA SYMPHONIC TAEKWANG TANDY TEAC TECHNICS TECHWOOD THETA DIGITAL TOSHIBA VECTOR RESEARCH 080 VICTOR WARDS YAMAHA YORX 010 020 025 056 174 175 176 239 044 107 228 103 008 182 017 042 150 042 050 051 102 181 182 187 044 107 161 178 250 044 107 044 069 107 128 171 190 125 050 069 102 026 031 051 066 003 019 051 096 112 115 119 166 033 048 081 097 126 133 177 225 226 164 251 155 044 107 052 181 195 085 010 015 034 036 051 052 101 131 140 079 060 103 200 172 184 008 068 076 234 235 006 067 091 160 148 004 022 114 124 185 033 024 046 054 186 183 245 182 60 C D C O D E T A B L E S CODE NUMBERS 61 BRAND R V D DISH ECHOSTAR HUGHES HUMAX JVC PHILIPS RCA REPLAY NETWORKS SONY TIVO TOSHIBA 122 122 108 117 117 122 108 090 117 109 075 104 105 090 117 117 S E L B A T E D O C BRAND 3M AIWA APPLE/iPod ARCHER AURORA MULTIMEDIA AUTON BOSE CELADON CRESTRON DELL DMX DRAPER SCREEN DREAMVISION DWIN EVERQUEST EXTRON FAROUDJA FUJI GATEWAY HAUPPAUGE HP HUNTERDOUGLAS JERROLD JVC KENWOOD KENSINGTON KEYSPAN LITE-TOUCH LUTRON MAKITA MICROSOFT/XBOX MINDPATH NILES NSM PIANO DISC PLUS POLKAUDIO RUSSOUND SCIENTIFIC ATLANTA SIMA SOLO ELECTRONICS SOMFY SONY STARCOM TURBOSCAN VELODYNE X-10 XANTECH AUX-TAPE AIWA CARVER DENON FISHER GOLDSTAR HARMAN KARDON JVC KENWOOD LINN LUXMAN MAGNAVOX CODE NUMBERS 152 164 412 401 155 220 191 409 221 213 214 215 216 217 218 261 262 156 204 097 080 253 206 151 184 209 261 262 294 295 261 262 219 153 185 185 406 297 208 257 158 159 077 186 201 408 107 205 160 187 161 085 162 081 163 156 082 207 078 079 164 165 166 261 262 153 167 203 183 093 168 169 170 171 172 188 189 015 071 100 114 006 008 027 024 036 105 227 229 064 011 233 106 116 239 240 005 013 023 026 064 145 146 181 190 124 035 137 139 027 62 A U X C O D E T A B L E S 63 BRAND CODE NUMBERS X U A MARANTZ MCINTOSH MITSUBISHI NAD NAKAMICHI ONKYO OPTIMUS PANASONIC PHILIPS PIONEER QUASAR SANSUI SHARP SHERWOOD SONY TEAC TECHNICS TOSHIBA VICTOR YAMAHA 014 027 056 065 087 238 242 243 029 048 244 245 025 002 012 016 017 018 019 115 026 054 055 007 010 032 088 195 027 087 003 039 047 050 066 098 222 007 088 027 113 119 224 026 057 131 175 181 038 004 028 030 033 034 020 022 052 084 089 009 059 212 007 010 076 088 109 122 193 112 106 021 026 031 067 040 AUX-Media PC Controls DELL GATEWAY HAUPPAUGE HP KEYSPAN SONY TOSHIBA WINBOOK AUX - Gaming System Controls MICROSOFT/XBOX SONY/PS2 AUX-iPod Controls APPLE/iPod BOSE KENSINGTON 261 262 261 262 294 295 261 262 297 261 262 261 262 261 262 408 107 414 412 401 409 406 S E L B A T E D O C 64 F r e q u e n t l y A s k e d Q u e s t i o n s Frequently Asked Questions What is a macro button?
A macro is a button on the RF20 that you setup to make a lot of things happen when you press it. For example, to watch a DVD in most home theaters requires several remote controls and many button presses (power up the TV, power up the surround sound, power up the DVD player, set the TV to the correct video input, set the surround sound to the correct audio input and finally;
press play on the DVD player remote control). Instead of pressing all of those buttons one at a time, the RF20 enables you to setup one button that does all those steps automatically with one press. For more information on how and why you should setup macro buttons, watch the Quick Setup DVD Program Guide or refer to pages 26-29 in this Manual. If the batteries run out, will I lose my settings?
No. The RF20 stores all of your settings in non-volatile FLASH memory. You could remove the batteries for months, replace them at your convenience, and the RF20 would still remember your settings. Who can I call for more answers?
The Universal Remote Control Technical Support and Customer Service staff are ready to answer any questions you might have. Call us at 1-914-835-4484 Monday - Friday, 9AM to 6PM (EST) O T H E R I N F O 65 s n o i t a c i f i c e p S
y t n a r r a W O F N I R E H T O USALimited Warranty Statement Your Universal Remote Control, when delivered to you in new condi-
tion, is warrantedagainst defects in materials or workmanship as fol-
lows: UNIVERSALREMOTE CONTROL,INC. warrants this product against defects in material or workmanship for a period of one(1) year and as set forth below. Universal Remote Control will, at its sole option, repair theproduct using new or comparable rebuilt parts, or exchange the product for a comparablenew or rebuilt product. In the event of a defect, these are your exclusive remedies. This Limited Warranty covers only the hardware components pack-
aged with the Product. Itdoes not cover technical assistance for hard-
ware or software usage and it does not coverany software products whether or not contained in the Product; any such software is pro-
vided "AS IS" unless expressly provided for in any enclosed software Limited Warranty. To obtain warranty service, you must deliver the product, freight pre-
paid, in its originalpackaging or packaging affording adequate protec-
tion to Universal Remote Control at theaddress provided in the Owner's Manual. It is your responsibility to backup any macropro-
gramming, artwork, software or other materials that may have been programmed intoyour unit. It is likely that such data, software, or other materials will be lost during serviceand Universal Remote Control will not be responsible for any such damage or loss. Adated purchase receipt, Bill of Sale, Installation Contract or other verifiable Proof ofPurchase is required. For product support and other important information visit UniversalRemote Control's website:
http://www.UniversalRemoteControl.com or call the UniversalRemote Control Customer Service Center (914) 835-4484. This Limited Warranty only covers product issues caused by defects in material or work-manship during ordinary consumer use. It does not cover product issues caused by anyother reason, including but not limited to product issues due to commercial use, acts ofGod, third-
party installation, misuse, limitations of technology, or modification of or to anypart of the Universal Remote Control product. This Limited Warranty does not coverUniversal Remote Control products sold as USED, AS IS, REFURBISHED, so-called "BSTOCK" or consumables
(such as batteries). This Limited Warranty is invalid if the factory-
applied serial number has been altered or removed from the product. This LimitedWarranty is valid only in the United States of America. 66 T h e R f 3 0 R e m o t e This Limited Warranty specificallyexcludes products sold by unautho-
rized resellers. UNIVERSALREMOTE CONTROLSHALLNOT BE LIABLE FOR ANYINCI-
DENTALORCONSEQUENTIALDAMAGES FOR BREACH OF ANYEX-
PRESS OR IMPLIED WARRANTYOR CONDITION ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BYAPPLICABLE LAW, THERE IS NO OTHER WARRANTYEXPRESSED OR IMPLIED. UNIVER-SALRE-
MOTE CONTROLWILLNOT BE HELD RESPONSIBLE FOR STATEMENTS MADEBYOTHERS CONCERNING THE MERCHANTABILITYOR FITNESS FOR APARTICULARPURPOSE ON THIS PRODUCT. Some states or jurisdictions do not allow the exclusion orlimitation of incidental or consequential damages, or allow limitations on how long animplied warranty lasts, so the above limitations or exclusions may not apply to you. ThisLimited Warranty gives you specific legal rights and you may have other rights which varyfrom state to state or jurisdiction to juris-
diction. Specifications Learning Capability - 825 IR commands at standard frequencies (15kHz to 100kHz) Macro Capability - 453 Macros of up to 190 steps each IR Range (Line of Sight via Infrared): 30-50 feet, depending on the environment RF Range (radio frequency): 50 to 100 feet, depending upon the environment RF Frequency: 418MHz Weight: 7.1 oz. (with batteries) Size: 8.5 x 2.5 x 1 Batteries: Four AAA Alkaline batteries included LCD Size: 0.88 x 1.88 O T H E R I N F O 67 e t o m e R 0 3 f R e h T Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. Warning!
Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Note : The manufacturer is not responsible for any Radio or TV inter-
ference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equip-
ment. FCC Caution This device complies with Part 15 of the FCC Rules. Operation is sub-
ject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equip-
ment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. O F N I R E H T O 68 I n f o r m a t i o n T o T h e U s e r
W a r n i n g O T H E R I N F O
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2009-10-14 | 418 ~ 418 | DSC - Part 15 Security/Remote Control Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2009-10-14
|
||||
1 | Applicant's complete, legal business name |
Ohsung Electronics Co., Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0011415411
|
||||
1 | Physical Address |
#181 Gongdan-Dong, Gumi-Si
|
||||
1 |
Gyeongsangbuk-Do, N/A
|
|||||
1 |
South Korea
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
T******@TIMCOENGR.COM
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
OZ5
|
||||
1 | Equipment Product Code |
URCRF20N
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
H****** K****
|
||||
1 | Title |
General Manager
|
||||
1 | Telephone Number |
82-54********
|
||||
1 | Fax Number |
82-54********
|
||||
1 |
k******@ohsungec.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 11/27/2009 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSC - Part 15 Security/Remote Control Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | RF REMOTE CONTROLLER | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
GUMI UNIVERSITY EMC CENTER
|
||||
1 | Name |
T**** P******
|
||||
1 | Telephone Number |
82-54********
|
||||
1 | Fax Number |
82-54********
|
||||
1 |
t******@gumi.ac.kr
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15.231 | 418.00000000 | 418.00000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC