FCC ID: 2A39R-MEGAMIFI OmegaWireless

Mobile Hotspot User Manual SIM Card How to insert SIM Standard SIM card microSIM nanoSIM Remove the cover (there is a gap mouth in the bottom left corner on the back) Please put the original battery into the device correctly, close the cover. Battery instructions Please do not make battery short-circuit, to avoid it damaged, Forbidden to put battery under high temperature or throw it into Indicator light heat generationed and fired. fire to avoid explosion. Do not disassemble battery. Please insert standard sim, small card can be restored with a card sleeve. If the battery will not be used for a period of time, please discharge it and store it in a dry, dark, and cool place. Please stop using it when the battery and charger are damaged or obviously aged. Please put the used batteries in the designated collection point, and do not throw them away as ordinary garbage and pollute the environment. warn:

If the battery is damaged, DO NOT contact with the substance inside. If it is contaminated on the skin, rinse it with plenty of water. If necessary, seek the help of a doctor. Thank you for choosing our product, please read this manual carefully before using, follow the steps to use this product, after reading, please keep it for future reference Light Signal status Status Flashing blue: Network connected successfully. Steady blue: Data is disconnected. Steady red: 1. The device is powered on;

2. SIM is not detected or there is no network or other error states. WiFi status Blue on: WiFi is enabled, if disabled WiFi, light is off. Blue flashing: data transmission SMS status Blue on: new text messages received or unread messages Blue flashing: SMS is full Shut down Red flashing: charging Steady red: battery is fully charged Power status Boot up Red flashing: charging Red flashing & blue on: battery fully charged Only blue on: sufficient power Blue flashes slowly: low power Blue flashes quickly: low battery, its about to shut down Please pay attention to the contacts of the battery. Please turn off the device and remove battery, then insert sim card. Please pay attention to the direction of SIM card. There is a slot for micro SD card on the right. After inserting SIM and battery correctly, press power switch about 5 seconds to boot it, it can be used normally. SIM Slot micro SD Slot 5 seconds How to insert micro SD How other devices connect the network?

Device Management please insert micro SD directly without bending or tilt Choose one of the following methods to connect to the Internet. micro SD Slot By WPS Long press WPS button to turn it on for quick connection (refer to the below image) Find the WiFi name Recommended connected method In the boot-up state, networking devices can connect to the default WiFi transmitted by the device for wireless Internet access. You can find the wifi name and password on the label If insert it tiltly, it will be easily damaged the internal contacts of the SD card slot and cause problems such as it cannot be read. micro SD Slot Long press WPS button for more than 2 seconds Device label This is an error demonstration If you want to view the SD card data, you can connect to the computer by data cable. WPS is just a Press WPS button until LED light on. quick connection method, it requires your cellphone or other devices supported WPS, then this function can work. If you don't know how to connect, you can connect with WiFi name and password. When the device is connected, please go to browser, you can enter 192.168.100.1 or http://mymifi.com, to access the device management interface. Enter the default login password "admin" to log in. If you are unable to log in, you can also check the device sticker to obtain the management address and login password. User Name Password Login Forget Password The above screenshots are for reference only.If there is any change, please refer to the actual display. If it is connected via a data cable, the computer needs to be set to automatically obtain an IP address. If you still cannot log in to the management interface, the IP address may have been modified before, please try to restore the factory settings. Using a needle-like object, press the RESET button of the device for 5-8 seconds, wait for the device to restart, and the factory reset is complete. 5-8 S FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF warning statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. SAR Information Statement The product is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted with the product transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the product while operating can be well below the maximum value. This is because the product is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a product model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model product when tested for use worn on the body, as described in this user guide, use at the worn on the body is 1.221W/kg.

(Body-worn measurements differ among phone models, depending upon available accessories and FCC requirements). While there may be differences between the SAR levels of various product and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model product with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model product is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/ oet/fccid after searching on. FCC ID: 2A39R-MEGAMIFI Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Asso-ciation (CTIA) web-site at https://

www.ctia.org/ In the United States and Canada, the SAR limit is 1.6 watts/kg (W/kg) averaged over onegram of tissue. The standard incorporates a sub-stantial margin of safety to give additional protectionfor the public and to account for any variations in measurements. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm is used between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

Omega Analytics Inc Declaration on Model Differences We, Omega Analytics Inc 129 S. Main Street STE 260 Grapevine, Texas 76051 USA Declare that the following product(s):

FCC ID: 2A39R-MEGAMIFI Product Name: OmegaWireless Model No.: MEGAMIFI, MoshiMIFI, FloMobile, REDmifi, BLUEmifi Utilize the identical circuit design, PCB layout, shielding and interface with (MEGAMIFI), only the model name different. Therefore this application can be regarded as identical in performance to the submitted test sample. The manufacturer would take all the responsibilities for the above product(s). For and on behalf of Authorized person Name: Joe Miskell Position: Manager Date of issue: 2022-01-19

*I hereby declare that I am entitled to sign on behalf of the applicant and that the information supplied is correct and complete.

Omega Analytics Inc Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2A39R-MEGAMIFI Date: 2022-01-19 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

Schematic Diagram Block Diagram Operational Description SW SECURITY DESCRIPTION Parts List Tune up External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Joe Miskell Title: Manager

Omega Analytics Inc Letter of Authorization Company: Omega Analytics Inc Address: 129 S. Main Street STE 260 Grapevine, Texas 76051 USA Product Name: OmegaWireless Model Number(s): MEGAMIFI, MoshiMIFI, FloMobile, REDmifi, BLUEmifi Product Description: OmegaWireless We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Joe Miskell Title:

Manager Company: Omega Analytics Inc Date: 2022-01-19