FCC ID: SV4-OM504 OmiDetect 50

OmiDetect 50 TPM Sensor Tester l a u n a M s r e s U CH041006 Rev A.1 OM504/2 The information, specifications and illustrations in this manual are based on the latest information available at the time of publication. The manufacturer reserves the right to make equipment changes at any time without notice. Copyright 2007 Omitec, Inc. All rights reserved. OmiDetect is a registered trademark of Omitec, Inc. Printed in the U.K. OmiDetect 50 Table of Contents 1. INTRODUCTION ............................................................................2 Direct Versus Indirect Systems ..................................................3 About Sensors ............................................................................4 Activating Sensors ......................................................................4 Reprogramming ..........................................................................5 2. SAFETY INFORMATION...............................................................7 3. KIT CONTENTS .............................................................................9 4. CONTROLS AND INDICATORS .................................................10 5. OPERATING INSTRUCTIONS ....................................................11 6. WHAT TO DO IF OMIDETECT CANNOT ACTIVATE THE TPM SENSOR ..................................................14 Technique A..............................................................................14 Technique B..............................................................................14 7. REPROGRAMMING THE TPM CONTROL MODULE................15 8. VEHICLE COVERAGE GUIDE....................................................16 9. SPECIFICATIONS .......................................................................19 10. TROUBLESHOOTING ...............................................................20 11. CARE AND MAINTENANCE .....................................................21 12. WARRANTY ...............................................................................21 13. TECHNICAL SUPPORT.............................................................21 Introduction 1. Introduction Congratulations on your purchase of the OmiDetect 50 Tire Pressure Monitoring (TPM) sensor tester. To enjoy safe and the best performance from your OmiDetect 50, please read and follow all instructions, recommendations and warnings. Understanding the basics of tire pressure monitoring systems is essential to using the OmiDetect effectively, so be sure to review the following sections thoroughly. OmiDetect is a state-of-the-art tester designed especially for automated and manual testing of Schrader TPM valve sensors for correct operation. Used properly, it will allow you to quickly:

 Confirm that the vehicles Schrader TPM sensors are working properly before you start tire/wheel service work

(including rotating, changing or balancing tires/wheels). This will reduce the risk of your having to replace a sensor that was defective prior to your starting the work.

 Confirm that the vehicles Schrader TPM sensors are working properly after you complete tire/wheel service work.

 After rotating the vehicles wheels, activate their Schrader TPM sensors to allow the vehicle control unit monitoring the TPM sensors to identify their new location.

 Diagnose problems with Schrader TPM sensors and other TPM system components.

 Confirm that a Schrader TPM sensor you replaced is working properly.

 Confirm that you installed the correct type of sensor. History of TPM Systems In the wake of tire safety issues involving SUVs in the late 90s, Congress passed the Transportation Recall Enhancement, Accountability, and Documentation (TREAD) Act in 2000. The TREAD Act mandated that automotive manufacturers start phasing TPM systems into all their new light vehicles with a GVWR of 10,000 pounds or less beginning in November 2003. By 2006, 90% of all light vehicles are to comply, and by Sept. 1, 2007, all new light 2 Introduction vehicles must comply. The total population of vehicles with TPM systems will grow from approximately 4 million units in 2003 to close to 50 million units by the end of the decade. The NHTSA, which is responsible for establishing and enforcing vehicle safety standards, published a mandate requiring that the TPM system must be capable of monitoring all four tires and alerting the driver if a tire is under inflated by 25% or more of the OEMs recommended tire pressure. Testing showed that proper tire inflation significantly improves vehicle handling safety, decreases tread wear, improves fuel economy, and decreases stopping distances. Underinflated tires are dangerous because they build up internal heat that can damage the tire structure, potentially resulting in fatal blowouts. Direct Versus Indirect Systems The NHTSAs mandate on TPM systems allows two system architectures. The first, called the direct system, uses a direct RF link from each wheel to a central receiving control unit, and the second, called the "indirect" system, works in conjunction with the vehicle's antilock-braking (ABS) system.

 Direct Systems. Wireless sensor in or on each wheel that

measures internal tire air pressure and temperature separately and communicates the readings by RF signals to a receiver/controller control unit at regular intervals. The sensors have an integral low frequency transmitter and are typically built into or mounted on the valve stem. The end of the valve stem serves as the sensors antenna. Most direct systems share the receiver control unit with the vehicles keyless entry system. Indirect Systems. Monitors rotation of tires via the vehicles antilock braking system (ABS) to calculate whether they are properly inflated. Does not measure tire pressure or temperature. The system measures the wheel speed of all four tires and calculates a rolling circumference for each one. In the event of a tire pressure loss, the rolling circumference of that tire is reduced, producing a change in the tires rotational speed. The NHTSA found that direct TPM systems are preferred because they are better able to detect under- or over-

inflation and are quicker to provide alerts. Virtually all vehicle manufacturers today have moved to direct systems. 3 Introduction Schrader TPM Sensor Vehicle manufacturers using Schrader TPM sensors:

 Ford

 Chrysler

 GM

 Infiniti

 Mitsubishi

 Nissan

 Saab

 Volvo About Sensors TPM sensors are micromechanical devices (a silicon-based vacuum cell) powered by a lithium battery with a minimum life expectancy of up to 10 years. Using their piezoresistive technology, they monitor tire pressure via measuring the deformation of an internal diaphragm. They typically transmit measurement values and sensor ID data at 433 MHz (for European systems) or 315 MHz (for U.S. systems) to the receiver control unit once per hour when the vehicle is parked

(and only if the pressure changes), to preserve battery life, and every few seconds when the vehicle is traveling above a certain speed (typically about 20 mph). If the tire pressure rises or falls outside calibration limits, a warning light or message is displayed in real time on the vehicles instrument panel, along with an audible warning, to alert the driver. Activating Sensors To activate, or wake up, a TPM sensor to test its ability to sense and transmit tire pressure and sensor ID information to the TPM control module, you must use one of three different methods, depending on the type/brand of sensor:

4 Introduction

 Send the sensor a 125 KHz continuous wave command signal (

 Send the sensor a 125 KHz modulated wave command signal (

 Position the magnetic tool specified by the OEM in close proximity to the sensor. The tool is provided with the vehicle or is available from the OEM. OmiDetect 50 can activate only sensors capable of being activated with a continuous wave command signal, primarily Schrader sensors. Many current-generation sensors can be activated using that method. Once a sensor is activated, OmiDetect will listen for the appropriate response signal. If it detects a valid signal, it will provide both visual and audible confirmation and indicate its frequency (either 315 MHz or 434 MHz). Note: Older generation sensors may not have the electronics required to activate them using these methods. Reprogramming Each TPM sensor has a unique internal identification code. With most current generation TPM systems, anytime you rotate a vehicles tires or replace one or more TPM sensors, you must reset

(reprogram) the TPM systems control module by placing it in the learn mode and activating each sensor so the control module can identify the new sensor locations. Refer to the Omitec TPM System Quick Reference Guide provided with your OmiDetect system for instructions on how to reset the TPM system of a specific vehicle make and model. IMPORTANT: If you do not reprogram the control module, it will continue to report the correct tire pressures, but will assign them to the wrong wheel locations. Other Cases Where You Will Need to Reprogram the TPM Control Module If the vehicles battery or the TPM control module is disconnected or the voltage to the TPM system drops below a certain value, the control module will loose all its sensor ID information and will set a 5 Introduction DTC for a TPM fault. In this case, you will need to reprogram the control module and clear the DTC. Figure 1. OmiDetect shown in use in testing a TPM sensor. 6 Safety Information 2. Safety Information IMPORTANT SAFETY NOTICE For your safety, read this manual thoroughly before operating your OmiDetect system. It is intended for use by properly trained professional automotive technicians. The safety messages presented below and throughout this users manual are reminders to the operator to exercise care when using it. Before using your OmiDetect system, always refer to and follow the safety messages and applicable service procedures provided by the manufacturer of the vehicle being serviced. WARNING Risk of injury This device emits an electromagnetic field which may interfere with the safe operation of medial equipment such as a heart pacemaker. Individuals fitted with a pacemaker should never use this device. WARNING Risk of injury Never contact the OmiDetect tester to moving components, drive belts and other moving components. WARNING Risk of electrical shock To avoid possible serious injury from electrical shock, never contact OmiDetect to electrical components. CAUTION General Safety Precautions 1. Do not attempt to use the Tire Pressure Monitor System while adjusting tire pressures, since they do not function as a real-

time tire pressure gauge. 2. Tire pressure monitor equipment was calibrated for the original vehicle tire size. Use only original tire sizes to maintain system accuracy. 3. Tire sealants should not be used on vehicles equipped with a Tire Pressure Monitor System. Those sealants can clog the sensors, rendering them ineffective. 4. Do not attempt to install a tire pressure sensor in a steel or aftermarket wheel. Tire pressure monitor equipment is only to be used on original style factory wheels. 5. Always replace a damaged or inoperative TPM sensor/transmitter. 7 Safety Information 6. Never clean a TPM sensor/transmitter with compressed air or steam. Damage to the sensor/transmitter may result. 7. The cap on the valve stem or a TPM sensor/transmitter frequently contains a O-ring to prevent contamination and moisture from entering. Be sure to retain this cap for reuse. 8. Strong radio waves may interfere with the proper operation of some TPM systems. 9. Snow, ice or mud in the wheel wells and tire chains mounted on the tires may cause a TPM system to malfunction. 10. Check that the vehicles ignition is Off and that its parking brake is properly set. 11. Do all testing in a well-ventilated area. 12. Do not smoke or allow sparks or open flame near fuel system parts. 13. Do not smoke or allow open flame near a battery. 14. Do not wear watches, rings or loose-fitting clothing when working near operating equipment. 15. Wear safety goggles at all times while operating OmiDetect. Rotating equipment components or electrical equipment can cause flying particles. CAUTION General Operating Precautions 1. Keep OmiDetect away from metal objects, such as clamps, wheel alignment or other tire/wheel equipment, since they will impede OmiDetects ability to receive a good RF signal from a TPM sensor. 2. Keep OmiDetect away from any known RF transmitters, such as mobile phones and other RKE (Remote Keyless Entry) transmitters. Signals received from these devices could result in the incorrect RF signal being detected. Caution Misdiagnosis may lead to incorrect or improper adjustment and/or repair. 1. Do not rely on erratic, questionable or obviously erroneous test information or results. If test information or results are erratic, questionable or obviously erroneous, verify that the test procedure was performed correctly. If test information or results are still suspicious, do not use them for diagnosis. Improper adjustment or repair may cause equipment damage or unsafe operation. 8 Safety Information Kit Contents Your OmiDetect 50 kit includes:

 OmiDetect 50 TPM Sensor Tester

 9V 6LR61 Battery

 OmiDetect 50 Users Manual OmiDetects internal 9 volt battery Important: Your OmiDetect systems internal 9 volt alkaline battery must have sufficient charge for the system to work properly. If it drops below the minimum required, after you power the tester on, it will sound a constant tone and illuminate the Low Battery Indicator LED (see Sec. 4) for 5 seconds, then the system will automatically power Off. OmiDetect will not indicate a valid test result when the battery is low. For optimum performance, the recommended batteries are PP3, IEC 6LR61 or 6F22. Do not dispose of batteries in household refuge. Some communities offer recycling or collection of alkaline batteries. Contact your local government for disposal practices in your area. To replace the battery:

1. Remove battery compartment door from back of unit and check that the 9V alkaline battery is properly connected to the battery wiring harness connector. 2. Replace battery compartment door. 9 Setup Procedure 3. Controls and Indicators OmiDetects display has a series of 6 LEDs and a Low Battery Indicator LED. Figure 2. OmiDetect 50's LED Display. The 6 LEDs have three functions:

 The first LED (1) illuminates when the Listen mode is selected, letting you test a TPM sensor activated manually, rather than electronically using OmiDetect.

 The second LED (2) indicates the TPM sensor mode. In this mode OmiDetect will activate a Schrader valve by transmitting a continuous RF signal.

 The middle two LEDs (3) indicate the frequency of the response RF signal detected from the TPM sensor under test, either 315MHz or 433MHz.

 The next LED (4) illuminates to indicate a valid sensor signal was not detected during the test cycle.

 Note : On power On OmiDetect automatically reverts to the last test mode used. The Low Battery Indicator LED (5) illuminates to indicate OmiDetects internal 9 volt battery is low and should be replaced (see preceding section). 10 Keypad Buttons Setup Procedure Press to power On/Off the tester and to select TPM sensor Mode. Also lets you select the Listen mode to test sensors activated manually, rather than electronically using OmiDetect. Press to start testing, causing OmiDetect to activate the TPM sensor and listen for a valid response RF signal from it. 4. Operating Instructions When operating OmiDetect to test a Schrader TPM sensor for proper operation, you will always perform these steps:

1. Confirm that the vehicle is equipped with Schrader TPM sensors. For help identifying the type of sensor installed on the vehicle, refer to Sec. 8, Vehicle Coverage Guide, or to the vehicle manufacturers appropriate service information. 2. Hold the front end of OmiDetect on or close to the tirewall, where it meets the wheel rim, directly below the sensor. Important: Do not aim directly at the valve stem. Since it is metal, it will impede receiving a good RF signal from the sensor. With low-profile tires, since the area for the 11 Setup Procedure RF signal to penetrate the sidewall is small, carefully aim OmiDetect halfway between the tire rim and the tire tread. 3. Power On the OmiDetect tester, by pressing and holding down the power On/Off button for 2 or 3 seconds. You will hear a beep and the LED array will illuminate and display the last test mode used. 4. Select TPM sensor mode by pressing the power On/Off button until the LED under the Tire symbol illuminates. With each press of the power On/Off button, you will hear a beep and the LED display will alternate between the Listen and the TPM sensor mode LEDs. Important: As a battery life saving feature, if you do not select a sensor type within 30 seconds of powering On OmiDetect, it will assume no testing is required and automatically power itself Off. If the sensor you are testing is not currently supported by OmiDetect, refer to Sec. 6 for information on how you can activate the sensor manually. 5. Press the button to test the sensor. The TPM LED illuminated will begin to flash to indicate OmiDetect is activating the sensor and listening for the appropriate RF signal from it. 12 Setup Procedure Once OmiDetect detects the appropriate response signal, it will beep 3 times, the LEDs will stop flashing, and the LED for the frequency of the response signal it detected (either 315MHz or 433MHz) will illuminate for 5 seconds to indicate the sensor is operating properly. If it does not detect the appropriate signal, you will hear a continuous beep and the X LED will illuminate continuously, indicating the sensor is not operating properly. OmiDetect will then reset itself back to the last test mode used ready for the next test. If OmiDetect is unable to activate the sensor, be sure to confirm that you selected the correct sensor type for testing. Also, remember that some sensors cannot be activated electronically and must be activated magnetically. (Refer to the Omitec TPM System Quick Reference Guide for information on whether the sensor must be activated magnetically.) If necessary, you can activate a sensor manually using one of the techniques outlined in the following section. To cancel a test once it has started, simply press and hold down the Power On/Off button for 3 seconds. OmiDetect will then automatically power itself Off. Important: If the wheel service work you are performing on the vehicle includes rotating the tires or replacing a TPM sensor, with most TPM systems you must reprogram the TPM control module so it can identify the new TPM sensor locations, covered in Section 6. 13 Setup Procedure 5. What to Do If OmiDetect Cannot Activate the TPM Sensor If OmiDetect is unable to activate a TPM sensor, you can use either of the two following techniques to manually activate it to allow you to test it for proper operation. Technique A 1. Depress the tires valve stem to release air pressure for about 5 to 8 seconds. The TPM sensor will detect the loss of tire pressure, causing it to transmit a signal to the vehicles TPM control module. 2. Power On the OmiDetect tester (if necessary repeatedly press the power On/Off Button until the first LED illuminates). Then press the button to put OmiDetect in the listening mode for manual testing. The LED will begin to flash, indicating OmiDetect is listening for an RF transmission signal from the TPM sensor. If OmiDetect detects a valid signal, it will beep 3 times and illuminate the appropriate signal frequency LED for 5 seconds. Technique B 1. Using a tire/wheel balancer, spin the tire/wheel at the speed required to cause the TPM sensor to start transmitting tire pressure measurement signals to the vehicles TPM control module. Note: Recall that all TPM systems automatically start transmitting pressure measurement and sensor ID data every few seconds when the tire is rotating above a certain speed, typically about 20 mph. 2. Power On the OmiDetect tester (if necessary repeatedly press Power ON/OFF button until the first LED button to put OmiDetect illuminates). Then press the in the listening mode for manual testing. The LED will begin to flash, indicating OmiDetect is listening for an RF transmission signal from the TPM sensor. 14 Setup Procedure If OmiDetect detects a valid signal, it will beep 3 times and illuminate the appropriate signal frequency LED for 5 seconds. 6. Reprogramming the TPM Control Module With most current generation TPM systems you will need to reprogram, or reset, the vehicles TPM control module any time:

 You rotate a vehicles tires

 You replace one or more TPM sensors, you must reset

(reprogram) the TPM systems control module by placing it in the learn mode and activating each sensor so the control module can identify the new sensor locations.

 The vehicles battery or the control module is disconnected or the voltage to the TPM system drops below a certain value, causing the control module to loose all its sensor ID information. (This will set a DTC for a TPM fault. In addition to reprogramming the control module, you also will need to clear the DTC.) IMPORTANT: If you do not reprogram the control module, it will continue to report the correct tire pressures, but will assign them to the wrong wheel locations. To reprogram the TPM control module:

1. Place the vehicles TPM control module in the learn mode. (The procedure required varies with vehicle makes and models. Refer to the Omitec TPM System Quick Reference Guide provided with your OmiDetect system for the procedure required for the vehicle you are servicing.) 2. Activate each TPM sensor (see Section 5), following the vehicle manufacturers requirements for the order in which the sensors are to be activated. With most vehicle makes/models you will be required to start with the front left wheel, followed by the right front, right rear, left rear, and spare tire, working clockwise around the vehicle. Typically, the vehicle will sound a series of two or more horn beeps to confirm its TPM control module was able to communicate with the TPM sensor and identify the sensors location. 15 Setup Procedure When finished activating all the TPM sensors, you may be required to drive the vehicle a specified distance and speed in order for the TPM control module to store the current tire pressures as new setpoints to be monitored. Refer to your Omitec TPM System Quick Reference Guide for more information. 7. Vehicle Coverage Guide OmiDetect 50 can test only vehicles fitted with Schrader TPMS sensors. As a broad guide, the table below lists some of the vehicle manufacturers using Schrader TPMS sensors (black filled circle indicates LED illuminated). OmiDetect 50 TPMS Vehicle Coverage List Vehicle Manufacturer Model Years TPMS Sensor Chrysler 300M 2002 - 2005 Schrader Crossfire 2004 - 2006 Schrader Grand Cherokee 2002 - 2004 Schrader Grand Cherokee 2005 - 2006 Schrader Liberty Liberty 2002 - 2004 Schrader 2005 - 2006 Schrader Pacifica 2002 - 2005 Schrader 16 Must Be Activated Manually Magnet required Magnet required Magnet required Magnet required Magnet required Setup Procedure Ford GM Prowler 2002 - 2003 Schrader Caravan 2002 - 2003 Schrader Caravan 2004 - 2006 Schrader RS Minivan 2002 - 2005 Schrader Town & Country 2002 - 2003 Schrader Town & Country 2004 - 2006 Schrader Aviator 2003 - 2005 Schrader Crown Victoria Escape 2005 - 2006 2005 - 2006 Schrader Schrader Expedition 2003 - 2006 Schrader Explorer 2003 - 2005 Schrader Freestar 2004 - 2006 Schrader Mark Lt Mercury 2005 - 2006 2005 - 2006 Schrader Schrader Navigator 2004 - 2006 Schrader Ranger 2004 - 2006 Schrader Town Car Chevrolet Avalanche Cadillac SRX Cadillac STS Cadillac XLR Envoy XL Escalade Escalade EXT Escalade ESV Impala Monte Carlo Ranier Sierra Silverado Suburban Tahoe Trailblazer 2005 - 2006 Schrader 2004 - 2006 Schrader 2004 - 2006 2005 - 2006 2004 - 2006 2006 2005 - 2006 2006 2004 - 2006 2005 - 2006 2005 - 2006 2006 2006 2004 - 2006 2004 - 2006 2005 - 2006 2006 Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Magnet required Magnet required Magnet required Magnet required Magnet required Magnet required Magnet required Magnet required Magnet required 17 2005 - 2006 2006 2005 - 2006 2005 - 2006 2005 - 2006 2005 - 2006 2004 - 2006 2004 - 2006 2005 - 2006 2005 - 2006 2005 - 2006 2005 - 2006 2005 - 2006 2005 - 2006 2005 - 2006 2005 - 2006 2005 - 2006 2005 - 2006 2005 - 2006 2004 - 2006 2004 - 2006 2004 - 2006 2004 - 2006 2004 - 2006 2004 - 2006 Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Schrader Setup Procedure Yukon Yukon XL M35 QX56 Q45 G35 Endeavour Galant 350Z Altima Armada Frontier Maxima Murano Pathfinder Quest Sentra Titan Xterra 9-3 S60 S80 V70 XC70 XC90 Infiniti Mitsubishi Nissan Saab Volvo 18 Setup Procedure 8.8.8.8. SSSSpecifications TPMS Valve Sensor Activation Inductively Coupled RF at 125KHz Activation Range 2 8 (50mm 200mm) depending on sensor and wheel type Activation Format Continuous Frequency RF Detection Frequencies Power Approvals 315 MHz & 433.92 MHz 9V Battery (Alkaline/Manganese) PP3, IEC 6LR61 or 6F22 Note: Do not use rechargeable batteries. Dispose of used batteries in accordance with local authority guidelines. FCC This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may cause harmful interference, and This device must accept interference received, including interference that may cause undesired operation. Industry Canada:

RSS210, RSSGEN 19 Troubleshooting 9. Troubleshooting Problem: Unable to activate a TPM sensor. Possible solution: Confirm that the vehicle is equipped with Schrader TPM sensors. Remember: OmiDetect 50 can activate only sensors capable of being activated with a continuous wave signal command. Possible solution: When aiming OmiDetect, be sure to hold it on or close to the tire wall where it meets the wheel rim, directly below the sensor. Do not aim directly at the valve stem, since it is metal and will impede receiving a good RF signal from the sensor. Possible solution: If you are testing/activating a TPM sensor fitted to a low-profile tire/wheel, be sure to carefully aim OmiDetect at the tire sidewall area halfway between the tire rim and the tire tread. Possible solution: If you are testing an older-generation sensor, you may have to activate it magnetically, rather than electronically using OmiDetect. Refer to the Omitec TPM System Quick Reference Guide or to the vehicle manufacturers appropriate service information to confirm the type of sensor installed on the tire/wheel and how you activate it. Possible solution: The sensor may be defective and have to be replaced. Problem: Inconsistent test results. Possible solution: OmiDetect will not indicate a valid test result when the battery is low (see Sec. 0). Problem: OmiDetect powers Off shortly after I power it On. Possible solution: As a battery life saving feature, if you do not select a sensor type within 30 seconds of powering on OmiDetect, it will assume no testing is required and automatically power itself Off. Also, once OmiDetect completes a test cycle, it will indicate whether it detected a valid signal and then automatically power itself Off after 5 seconds. Possible solution: The tools internal 9 volt alkaline battery may be low and need to be replaced. When the battery is low, after you power the tool On, it will 20 Operating Tips sound a constant tone and illuminate the Low Battery Indicator LED (see Sec. 3) for 5 seconds, then the system will automatically power Off. Problem: OmiDetect will not power On. Possible solution: The tools internal 9 volt alkaline battery may be low and need to be replaced (see above). 10. Care and Maintenance

 Your OmiDetect system should be cared for like any other piece of high-quality electrical equipment.

 To maintain the condition and serviceability of the system, you should periodically inspect and clean all the system components as necessary.

 Never spray any liquid directly on the system. Instead, moisten a soft cloth with water and a mild cleaning agent like window cleaning solution, then wipe the units clean.

 The systems internal 9 volt battery should be removed if the system is not used for extended periods.

 Use only a standard 9V alkaline battery when replacing it.

 The system does not need any adjustments or calibration. 11. Warranty The OmiDetect 50 TPM Sensor Tester has a one-year warranty against defects in workmanship and materials (excluding batteries). Any defective item returned within this time showing signs of abuse, tampering, neglect or misuse will be repaired at normal time and material costs. 12. Technical Support Technical support is available from Monday through Friday from 8:00 a.m. to 5:00 p.m. EDT by calling OmiDetect Technical Support toll-free at 1-800-434-6744 or by emailing techsupportusa@omitec.com. 21 Notes:

29777 Telegraph Road, Onyx Plaza, Ste. 1637 Southfield, MI 48034 Phone: (248) 799-2000 Technical support: (800) 434-6744 Email: techsupport@omitecusa.com Web site: www.omitecusa.com