EV_REMOTE operation manual Setting the air conditioner Configuration Part names Stick LCD Setting button (DOWN) Product label Power / Link button Mode setting button The car air conditioner can be controlled with the stick prior to getting into a car. Pressing the mode setting button once in the charge time setting mode enables the air conditioner setting mode. Select the temperature you want with the setting button and press the Power/Link button to send the setting information to the vehicle. If a response signal from the vehicle is properly received, the setting information will be displayed on the LCD with a buzzer sound. Turning the power of the stick off Pressing the Power/Link button for more than 3 seconds while the power is on turns the power of the stick off. Also no button operation for more than 30 seconds automatically turn the power off. Manual charge button Setting button (UP) Battery cover Caution When pulling the antenan out or putting it back, move it straight up/down with holding the top of the antenna. The antenna may be damaged if being pulled with brute force or bended. Antenna module Product label CN2 connector CN1 connector (antenna connection) Battery replacement 3 Main specifications Stick Transmission frequency 926.85 MHz band (FCC/IC), 869.85 MHz band (EU) Transmission power < 50 mV/m (FCC/IC), < 5mW e.r.p (EU) Antenna 1/4 lambda rod antenna Switches Power on/off, Mode, Charge, Setting Link state acknowledgment Buzzer / LCD Battery Lithium battery (CR2032 x 2) Operation temperature range -10 C to +70 C Dimensions 88.4 mm x 32 mm x 18 mm ( not including protrusion) Weight 35 g Antenna module Transmission frequency 926.85 MHz band (FCC/IC), 869.85 MHz band (EU) Transmission power < 50 mV/m (FCC/IC), < 5mW e.r.p (EU) We recommend that you replace the batteries after one year's use as a guide. Power supply 5 V Batteries: CR2032 x 2 How to replace the batteries 1. Remove the battery cover Battery cover Current consumption 1.5 mA (for receiving) Antenna 1/4 lambda printed antenna Operation temperature range -30 C to +85 C Dimensions 52 mm x 25 mm x 52 mm Weight 35 g Slide part 4 After sales service lithium batteries
(CR2032) For after sales service, contact :
OMRON Automotive Electronics Co. Ltd. 6368 nenjyozaka, okusa Komaki, Aichi 485-0802 JAPAN Tel: +81 568 78 6392 URL: http://www.oae.omron.co.jp Regulatory compliance FCC/IC WARNING Any changes or modifications not expressly approved by the party responsible for product compliance could void the user's authority to operate the equipment. This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of this device. Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC The following standards were applied: (R&TTE Directive 1999/5/EEC) EN 60950-1: 2006 + A11:2009 EN 300 220-2 V.2.3.1 EN 301 489-3 V.1.4.1 EN 62311:2008 Hereby, OMRON Automotive Electronics Co. Ltd., declares that Stick / Antenna module are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Slide the slide part of the battery cover in the direction of and lift the cover in the direction of to release the hooks of the battery cover ( ). 2. Replace the batteries Insert the new batteries (CR2032) with the positive ( + ) side facing up. 3. Place the battery cover After inserting the hooks of the battery cover ( ), lower the cover into position
( ) and slide the slide part in the direction of . How to use Turning the power of the stick on Pressing the Power/Link button for more than 1 second turns the power of the stick on (with a buzzer sound) and the stick starts transmitting a request signal to obtain vehicle information. If a response signal from the vehicle is properly received, the vehicle information will be displayed on the LCD with a buzzer sound. Setting the charge time The time till charging is started (charge wait time) and the charging time can be set with the stick. Pressing the mode setting button once while the vehicle informaiotn is displayed on the LCD enables the charge wait time setting mode. In the charge wait time setting mode, the charge wait time can be set with the setting button. After setting the wait time, the setting information will be sent to the vehicle by pressing the Power/Link button. If a response signal from the vehicle is properly received, the setting information will be displayed on the LCD with a buzzer sound. By pressing the mode setting button once during the charge wait time setting mode, the stick is set to the charge time setting mode. Set the charge time in the same way as done for setting the charge wait time. Pressing the manual charge button resets the timer setting.