FCC ID: ATM-SE-C7BTSE WIRELESS STEREO HEADPHONES

SE-C7BTSE User manual BT datas Chipset :QCC3034 BT version:V5.0 Adjust Form:GFSK Offer voltage:3.0-4.2V Support BT agreement: A2DP,AVRCP,HFP,HSP Working current 20mA Standby current 2mA Charging current :100mA Wireless transmit distance:10 meter Out power:MAX 6dBm RF: -80dBm<0.1%BER Frequency range :2.4GHz-2.480GHz Signal to Noise Ratio:75dB distortion factor: 0.1%

Temperature: 0C to +45C 1.Indicator 2 Volume+ / next chart 3 Volume- /previous chart 4 ON/OFF /play/pause 5 Usb 5 V Output Feature:

Enjoy music through Bluetooth Phone call with BT function Remote control music High sensitivity,omnibearing microphone design Apply for devices:with all BT mobile phone,iphone,Laptop Etc. Pairing:red&blue light blinking Pairing successful:blue light slow blink Charging: red light on,full charge blue light on

. BT earphone pairing 1.press and hold 3s open Pioneer E-C7 SE,Lasting to red &blue light blinking,into paring mode noted :Paring need to finish in 5 minutes,after 5 minutes earphone will shut off automatic 2.Open the phone or Bluetooth device ,Bluetooth searchor add new equipment" search Bluetooth headset Pioneer E-C7 SE, 3.Click on the device name connection, the connection has a successful connection tone and blue light flashing. This means that the connection is successful. Answer phone call incoming call tone or ring tones, short press (

), you can answer the call.Or use your phone to answer a call. Reject phone call Short press (

) or use the phone to stop the call . Phone call conversion 1.Long press (

) 3 seconds to transfer calls to the phone .if want to switch back to the headset , just long press 3 seconds again . Last number redial Double click (

) to redial last number Music playing Short press paly /pause,long press +to next chart,short press + volume UP;long press -to previous chart, short press - ,volume down . FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ATM-SE-C7BTSE IC: 6547A-SEC7BTSE 1. INTERIOR PHOTOGRAPHS Fig.1 BT Antenna Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ATM-SE-C7BTSE IC: 6547A-SEC7BTSE Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ATM-SE-C7BTSE IC: 6547A-SEC7BTSE Fig.5

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ATM-SE-C7BTSE IC: 6547A-SEC7BTSE 1. EXTERIOR PHOTOGRAPHS Fig. 1 Fig. 2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ATM-SE-C7BTSE IC: 6547A-SEC7BTSE Fig. 3 Fig. 4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ATM-SE-C7BTSE IC: 6547A-SEC7BTSE Fig. 5 Fig. 6 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ATM-SE-C7BTSE IC: 6547A-SEC7BTSE Fig. 7 Fig. 8 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ATM-SE-C7BTSE IC: 6547A-SEC7BTSE Fig. 9

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ATM-SE-C7BTSE LABEL AND LOCATION FCC ID: ATM-SE-C7BTSE Model No.: SE-C7BTSE Huohuotu wifi digital player early educational machine This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Size: L5.0cm*W3.0cm Label Location This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1

Onkyo Corporation Agent Authorization Company: Onkyo Corporation Address: 1-10-5 KOKUGIKAN FRONT BUILDINGYokoami, Sumida-ku, Tokyo Japan Product Name: WIRELESS STEREO HEADPHONES Trade Mark: Pioneer Model Number(s): SE-C7BTSE ISED Number: 6547A-SEC7BTSE We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2019-08-26 Name:

Tatsuya Azumi Title:

Manager Company: Onkyo Corporation

Onkyo Corporation Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2019-08-26 Subject; Request for Confidentiality FCC ID: ATM-SE-C7BTSE To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Tatsuya Azumi Title: Manager