Door and Window Sensor ooma home monitoring Mounting Instructions Top view door and window sensor Quick Start Guide To get started, download the Ooma Home Monitoring app and complete the initial setup. You can find it at ooma.com/
app. Keep the front side of both pieces even with each other if possible. light 4 ~=Download on the GET ITON we ag indicator A Ys App Store Google Play pairing L_J
( button 1 in. max |
|G
Using the included adhesive pads or screws, | iN mount one piece onto the moving part of your L | fe f door or window, and mount the other onto your |' q door or window frame. When your door or ff window is closed, the dots should be no more ~
than 1 inch apart. If needed, attach additional risers (included) to raise the height of the magnet tab. Quick Reference Need Help?
Pairing Button Support Articles:
www.ooma.com/support e Tap to check battery level and to page mobile app User Manuals:
qummmmp long flash = battery good www.ooma.com/userguide low blink = battery |
@ slow Bln anvery low Community Forum:
forums.ooma.com Game Press and hold for five seconds to start pairing mode Live Customer Care:
1-888-711-6662 (US) 1-866-929-6662 (Canada)
@@@@ fast blink = pairing mode Tamper Switch Legal Sends you a notification when disengaged. For warranty, safety, and other legal information, visit ooma.com/legal Software Update If your sensor is updating its software, it will blink twice and pause continuously. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Water Sensor 3 ooma home monitoring Mounting Instructions water sensor ail light Quick Start Guide indicator To get started, download the Ooma Home Monitoring app and complete the initial setup. You can find it at ooma.com/
app. quick release button
/ pairing \ . A 4 Download on the GET ITON CZ- button A LC App Store Google Play , :
| , : If you are mounting the water probe using screws, remove the screw cap to expose the screw hole. NX worsy CQ9l>r Ve x Using the included adhesive pads or screws, mount the larger device piece somewhere away from where you expect water. (It is not waterproof.) Mount the water sensor probe either standing up or laying down such that the water would make contact with the two gold probes. Quick Reference Need Help?
Pairing Button Support Articles:
www.ooma.com/support e Tap to check battery level and to page mobile app User Manuals:
qummmmp long flash = battery good www.ooma.com/userguide
@ @ @ slow blink = battery low Community Forum:
forums.ooma.com Game Press and hold for five seconds to start pairing mode Live Customer Care:
1-888-711-6662 (US) 1-866-929-6662 (Canada)
@@@@ fast blink = pairing mode Tamper Switch Legal Sends you a notification when disengaged. For warranty, safety, and other legal information, visit ooma.com/legal Software Update If your sensor is updating its software, it will blink twice and pause continuously. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Motion Sensor ooma home monitoring Mounting Instructions motion sensor Quick Start Guide light indicator To get started, download the 2S (hidden) Ooma Home Monitoring app motion and complete the initial setup. sensor You can find it at ooma.com/ lens app. CA YT Cede ol dat GET ITON LC App Store Google Play pairing If desired, the motion sensor may be mounted
} a in a 90 corner using these four screw mounts. foot attachment Max range = 30 ft. tamper switch battery door ( i i y Use the included adhesive pads or Screws to The included foot attachment can be used to mount the sensor within range of the desired install the motion sensor on any flat surface area. :
magnetic mouting plate without adhesive pads or screws. Quick Reference Need Help?
First Time Setup Support Articles:
Wwww.ooma.com/support
== & s First time setup lasts 30 secs. after inserting batteries. Light blinks red until complete. User Manuals:
Pairing Mode wwwooma.com/userguide e@eeee Press and hold for pairing button for five seconds to start pairing mode. Light quickly blinks green while in this mode. Community Forum:
forums.ooma.com Live Customer Care:
1-888-711-6662 (US) 1-866-929-6662 (Canada) Pairing Success qummmmmmms Light will flash green for 3 seconds. Unpairing Success
@ @ @ Light will slow blink for 20 seconds. Legal For warranty, safety, and other legal information, visit ooma.com/legal Motion Sensed e Light will blink red once when motion is sensed. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Signal Disconnected Gumus Light will flash red for 10 seconds if signal is disconnected. Tamper Switch Sends you a notification when disengaged.