FCC ID: UFOOPA3201 Wireless USB Adapter

Wireless USB Adapter OPA-3201 This manual provides specifications for the OPA-

3201 wireless USB adapter. Specifications Manual All information subject to change without notice. Document History Model Number:

Edition:

Date:

OPA-3201 2014-

OPA-3201 Specifications Manual Specification Number:

Original Spec Number:

SS14033 SS14025 Copyright 2014 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages. Packaging The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your scanner or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty. Trademarks Trademarks used are the property of their respective owners. Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12-17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-

446-1184 SUPPORT USA Phone: 800-636-0090 Email: support@opticonusa.com Web: www.opticonusa.com Europe Email: support@opticon.com Web: www.opticon.com OPA-3201 Specifications Manual Revision History Specification No. Product name

: SS14033

: OPA-3201 Edition Date Page Section Description of Changes First 2014/

Initial release OPA-3201 Specifications Manual Contents 1. Abstract..............................................................................................................................1 2. Overview ............................................................................................................................1 3. Basic Specifications .........................................................................................................2 4. Detailed View .....................................................................................................................3 5. Electrical Specifications...................................................................................................4 5.1. USB ............................................................................................................................4 6. Interface Specifications....................................................................................................4 6.1. USB Interface .............................................................................................................4 6.1.1. Connector........................................................................................................................ 4 6.1.2. USB Interface Circuit....................................................................................................... 4 6.2. Wireless Interface.......................................................................................................5 6.2.1. HID Specifications ........................................................................................................... 5 7. Environmental Specifications..........................................................................................6 7.1. Temperature...............................................................................................................6 7.2. Humidity .....................................................................................................................6 7.3. Vibration Strength (without packing)...........................................................................6 7.4. Vibration Strength (in individual packing) ...................................................................6 7.5. Drop Impact Strength (without packaging) .................................................................6 7.6. Drop Impact Strength (in individual packaging)..........................................................7 7.7. Electrostatic Discharge (ESD) Immunity ....................................................................7 8. Regulatory Compliance ....................................................................................................8 8.1. Product Safety............................................................................................................8 8.2. EMC ...........................................................................................................................8 8.3. Others.........................................................................................................................8 9. RoHS...................................................................................................................................9 10. Reliability .........................................................................................................................9 11. Precautions......................................................................................................................9 11.1. Handling ...................................................................................................................9 11.2. Radio Law ................................................................................................................9 11.3. Wireless Communication........................................................................................10 11.4. Frequency Baud .....................................................................................................10 12. Product Labels ..............................................................................................................11 13. Packaging Specifications.............................................................................................12 13.1. Individual Packaging ..............................................................................................12 13.2. Collective Packaging ..............................................................................................13 OPA-3201 Specifications Manual 14. Physical Features..........................................................................................................14 14.1. Dimensions.............................................................................................................14 14.2. Weight ....................................................................................................................14 14.3. Mechanical Drawing ...............................................................................................14 OPA-3201 Specifications Manual 1. Abstract This manual provides specifications for the OPA-3201 wireless USB adapter. 2. Overview The OPA-3201 is a USB adapter designed for Opticon wireless scanners, including the OPN-3200 and OPN-4200. The OPA-3201 allows for wireless operation without special settings. The OPA-3201 is simple and easy to use, just like USB scanners are. The OPA-3201 can be used as a USB HID keyboard on a host device such as PC. Alternative to the USB-HID keyboard interface, the OPA3201 can use the host's protocol stack via HCI (Host Controller Interface). 1 3. Basic Specifications Item OPA-3201 Specifications Manual Specification Note CPU FROM S e c t i o n C o n t r o l SRAM In dic at o r LED Bluetooth USB USB I t n e r f a c e S e c t i o n P o w e r E n v i r o n m e n a t S p e c i f i c a t i o n s l l R e g u a t o r y C o m p l i a n c e T e s t I m m u n i t y t F e a u r e s P h y s c a i EMC Other ESD Weight l 32 bit RISC 1 Mbyte 48 Kbyte Blue x 1 Frequency 2402 ~ 2480 MHz Specification Communication distance Output level IEEE 802.15.1 compliant 10 m 4 dBm max Profile HID / SPP (HCI) Full-Speed 12 Mbps (HID) Low-Power class 4.5 ~ 5.5 V

-5 ~ 50C

-20 ~ 60C 20 ~ 85%RH 20 ~ 85%RH 10 Hz ~ 100 Hz, acceleration of 19.6 m/s2, 60 minutes per cycle, repeat once in each X, Y and Z-direction Drop the scanner 18 times (6 faces x 3) from the height of 150 cm onto a concrete floor EN60950-1:2005 IEC60950-1:2006 EN 55022:2010 EN 301 489-1 V1.9.2 EN 301 489-17 V2.1.1 EN 300 328 V1.8.1 FCC Part 15 Subpart C, Subpart B ClassB VCCI Class B CE Marking Certification for Construction Design of Specified Radio Equipment Air discharge (direct): 10 kV It may be shorter depending on usage environments Supporting SPP depends on hosts protocol stack USB power supply No condensing No frost For residential, commercial and light-

industrial environments Conditions:

IEC61000-4-2 compliant Approx. 6 g 2 Operating voltage Current consumption 100 mA or less Operating Storage Operating Storage Temperature Humidity Vibration Drop Product safety No distraction No malfunction Air discharge (direct): 8 kV Dimensions 43.8 8.3 17.4 (WDH mm) 4. Detailed View OPA-3201 Specifications Manual Figure 1: Detailed View of OPA-3201 Name No 1 USB connector 2 Address label Description A connector to connect to the host The OPA-3201s address bar code. A wireless connection can be established by reading this label with a scanner. 3 5. Electrical Specifications OPA-3201 Specifications Manual 5.1. USB Power supply voltage Bus-Power class Current consumption

: 4.5 ~ 5.5 V

: Low-Power

: 100 mA or less 6. Interface Specifications The OPA-3201 supports two types of interfaces; USB and wireless. 6.1. USB Interface The USB-HID interface is supported. 6.1.1. Connector Signal name Pin No. VCC Data(-) Data(+) GND 1 2 3 4 6.1.2. USB Interface Circuit Bluetooth Controller

+5.0 V power supply Front view Figure 2: USB Plug (A):

USB connector Data(+) 3 Data(-) VCC GND 2 1 4 Figure 3: Interface Circuit (USB) 4 OPA-3201 Specifications Manual 6.2. Wireless Interface The OPA-3201 uses IEEE 802.15.1 as the wireless interface. 6.2.1. HID Specifications Frequency Specification Communication distance Output level Implemented profile Communication configuration Operating mode in communication Security mode Encryption

: 2402 ~ 2480 MHz

: IEEE 802.15.1 compliant

: 10 m

: 4 dBm max

: HID

: 1 to 1

: Slave mode

: Authentication supported

: Encryption supported 5 7. Environmental Specifications OPA-3201 Specifications Manual 7.1. Temperature The performance is guaranteed when the range of ambient temperature is the following values:

Operating temperature Storage temperature

: -5 ~ 50 C

: -20 ~ 60C 7.2. Humidity The performance is guaranteed when the range of ambient humidity is the following values:

Operating humidity Storage humidity

: 20 ~ 85% RH (no condensation, no frost)

: 20 ~ 85% RH (no condensation, no frost) 7.3. Vibration Strength (without packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in the non-operating state. Repeat this in each X, Y and Z direction. 7.4. Vibration Strength (in individual packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6 m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in individually packaged state. Repeat this in each X, Y and Z direction. 7.5. Drop Impact Strength (without packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop the scanner 18 times in total (3 times at each 6 face) from a height of 75 cm onto a concrete floor as shown below. Figure 4: Drop Test 6 OPA-3201 Specifications Manual 7.6. Drop Impact Strength (in individual packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop an individually packaged scanner 10 times in total, at any of 1 corner, 3 edges, and 6 faces, from a height of 150 cm onto a concrete floor. 7.7. Electrostatic Discharge (ESD) Immunity

: 8 kV max (no malfunction) Aerial discharge 10 kV max (no distraction)

: Testing method compliant with IEC-61000-4-2.

: 330

: 150 pF Measurement environment Discharge resistance Charging capacitor 7 8. Regulatory Compliance OPA-3201 Specifications Manual 8.1. Product Safety EN60950-1:2005 IEC60950-1:2006 8.2. EMC R&TTE Directive EN 55022:2010 EN 301 489-1 V1.9.2 EN 301 489-17 V2.1.1 EN 300 328 V1.8.1 FCC Part 15 Subpart B Class B Federal Communications Commission Notices This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Harmful Interference Notice This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the separation between the equipment or devices Connect the equipment to an outlet other than the receiver's Consult a dealer or an experienced radio/TV technician for assistance Changes or modifications to this equipment that have not been approved by Ruckus Wireless may void the user's authority to operate this equipment.

VCCI Class B This is a Class B product, to be used in a domestic environment, based on the Technical Requirement of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. 8.3. Others Certification for Construction Design of Specified Radio Equipment 8 OPA-3201 Specifications Manual 9. RoHS The OPA-3201 is compliant with RoHS. RoHS: The restriction of the use of certain hazardous substances in electrical and electronic equipment, 2011/65/EC 10. Reliability MTBF (Mean Time Between Failures) 10,000 hours 11. Precautions 11.1. Handling Handle this product carefully. Do not deliberately subject it to any of the following.

(1) Shock:

Do not drop this product from a height greater than specified in this manual. Do not place this product under or between any heavy items.

(2) Temperature Conditions:

Do not use this product at temperatures outside the specified range. Do not pour boiling water on this product. Do not throw this product into a fire.

(3) Foreign Materials:

Do not immerse this product in water or other liquid. Do not expose this product to chemicals.

(4) Others Do not disassemble this product. Do not use this product near a radio or a TV. It may cause reception problems. This product may be affected by a momentary voltage drop caused by lightning. 11.2. Radio Law This product qualifies as specified radio equipment for radio stations of 2.4 GHz band data communication system and has obtained the Certification for Construction Design of Specified Radio Equipment. Therefore, radio station license is not required in Japan. The following activities are prohibited under the Radio Law:

Remodeling and disassembly Peeling off the certificate label Do not use this equipment under the following environment, as radio interference may affect other device and end up with causing physical or material damage. Safety apparatus and medical device for human body protection Environment where is concerned to cause serious damage 9 OPA-3201 Specifications Manual 11.3. Wireless Communication This product supports wireless communication with other devices that have the same specifications (profile). A wireless connection to any device other than Opticon products is not guaranteed. This product and the Opticon wireless scanners use the 2.4 GHz frequency band that is shared among other devices. It may affect the communication speed and distance between this product and the scanners. The communication speed and distance vary depending on the interference and radio wave condition between this product and the scanners. 11.4. Frequency Baud This product uses the 2.4 GHz frequency band. Read carefully the followings before using this product. In the frequency band of this product, scientific, medical and industrial devices including microwaves are used. Also other radio stations including local private radio station for mobile object identification requiring license for such as manufacturing lines at factories, specific power-saving radio station requiring no license and amateur radio station are managed. 1. Make sure that other radio stations are not managed in the frequency band 2.4 GHz before using this product. 2. In case that radio interference occurs between this product and other radio stations, change the service space immediately, or stop transmitting radio wave to avoid the interference. 3. If you have any questions or troubles, please contact our sales office. 10 OPA-3201 Specifications Manual 12. Product Labels The product label is affixed to the back of the OPN-3201 as shown below. Figure 5: Product Labels 11 OPA-3201 Specifications Manual 13. Packaging Specifications 13.1. Individual Packaging Assembled package size: xxx xxx xxx (WDH mm) Figure 6: Individual Packaging 12 OPA-3201 Specifications Manual 13.2. Collective Packaging Quantity Assembled package size

: 100 pcs

: xxx xxx xxx (WDH mm) Figure 7: Collective Packaging

* Ro mark on the boxes for the product indicates that the product is RoHS compliant declared by Optoelectronics Co., Ltd. 13 14. Physical Features 14.1. Dimensions 43.8 8.3 17.4 (WDH mm) 14.2. Weight Approx. 6 g (excluding accessories) 14.3. Mechanical Drawing OPA-3201 Specifications Manual

[Unit: mm]

Figure 8: Mechanical Drawing 14

OPTOELECTRONICS Co., Ltd. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 C.C.: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Requesting Class II permissive change for FCC ID: UFOOPA3201 To Whom It May Concern:

The purpose of this letter is to request a Class II Permissive change for FCC ID: UFOOPA3201, original granted on 41/12/2014. The difference with original product is change the capacitance and inductance between RF chip and antenna. Please contact me if you have any questions or need further information regarding this application. Best Regards Name: Satoru Konno Function: Development Group Manager Date: 2020/9/28 Satoru koaw Signature:

FCC, Request for non-disclosure Date: 21-Nov-2018 RF_501, Issue 8 Page 1 of 1 Name: OPTOELECTRONICS Co., Ltd. Address: 4-12-17, Tsukagoshi City: Warabi-shi, Saitama Pref. Country: Japan To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: UFOOPA3201 Reference number: ######

Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

LC) Bill's) of Material LJ Block Diagrams Antenna Specification

() Operational Description [J Schematic Diagrams L] Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (See notes below):

C1 Internal Photos (.] User's Manual LJ Test Set-up Photos External Photos SUSTFICATIONS oa accsseasssessecssecssssscssscsucevessessssssesosseacsasesassssvasasiessnssassnsssseensssuessccssessessssessesesseceaveenees Date: 2020/9/28 Name and signature of applicant: Satoru Konno Sato ra K OV AJO Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

The planned date should stated in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

OPTO Electronics Co., Ltd Declaration of Authorization We Name: OPTOELECTRONICS Co., Ltd. Address: 4-12-17, Tsukagoshi City: Warabi-shi, Saitama Pref. Country: Japan Declare that:

Name Representative of agent: Kent Liu Agent Company name: BTL Inc. Address: 4F,No.18, Ln. 171, Sec. 2, Jiuzong Rd., Neihu Dist., 114 City: Taipei Country Taiwan is authorized to apply for Certification of the following product(s):

Product description: Wireless USB Adapter. Type designation: OPA-3201 Trademark: OPTICON Validity/ expiry date: From 2020/9/28 to 2021/9/27 on our behalf. Date: 2020/9/28 City: Warabi-city Name: Satoru Konno Function: Development Group Manager Signature: Satern ko Vie