FCC ID: 2AVFRPF-240S BlueDrive S Power Fin

POWER FINTM BLUEDRIVE S Users Guide PF-240S WARNING For your own safety and that of your equipment, make sure to take the following precautions. Failure to follow warning notices and instruction may result in property damage, serious injury or death. Please keep the manual and read it carefully before using the product; If the manual is lost, please contact our after-sale service center. aquamarina.com TABLE OF CONTENTS I. SAFETY WARNING II. MAIN COMPONENTS, PARAMETERS AND OVERALL DIMENSIONS III. PACKING LIST IV. INSTALLATION AND INSTRUCTION V. MAINTENANCE VI. GUIDANCE ON PROBLEMS VII. WARRANTY AND AFTER SERVICE CONTACT INFORMATION SAFETY WARNING 1.This product is only for providing power for water leisure products and only limited to be used in water. It is forbidden to use it for other purposes. 2.When using the product, a proper emergency stop leash should be used 3.Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. 4.Do not modify the product or add other parts to it in any way. If any parts is damaged, Please contact after-sale service center. 5. Wash the power fin and its motor with fresh water; and do not put it in sea water or salt water to avoid damage to the motor. 6. This product is with li-ion batteries, always follow the batteries use principle and Matters needing attention. 7. The battery must be removed from the appliance before it is scrapped. 8. The appliance must be disconnected from the supply mains before removing the battery. 9. The battery must be disposed properly according to local regulations. 10. Never charge or use the product in thunderstorms and lightning conditions. 11. It is necessary to check whether each connection is firm before each use. 12. Check whether its electricity is enough before each use. 13. The power fin only be supplied at SELV(Safety Extra Low Voltage), can be applied only with specified batteries, specified chargers and remote control. If user needs to replace them, please contact the appointed after-sale service center. 14. The electric charging port of the battery case should be either connected with the power fin,or connected with charger, or cover its lid to avoid short circuit damage caused by other metals or moisture. 15. When the remote control and the charger are not used for a long time, it is necessary To disconnect power supply. 16. When it is not in use, it should be stored under the temperature of -

15~45 and avoid direct sunlight. 17. If the power fin is scrapped or need to be replaced with new one, it is necessary to follow the principle of recycling or return it to the dealer. 18. The appliance can be only used with specified chargers from the original manufacturer

. 19. The components with electric box and motor is for the field installed equipment, its installation to ISUP shall be considered the safety requirements of moving part, water proof and other risks FCC ID: 2AVFRPF-240S FCC statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following Two conditions:

(1) This device may not cause harmful interference, and

(2) this device mustaccept any interference received, including interference that may cause undesired operation. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF EXPOSURE WARNING The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. POWER FIN PRODUCT DETAIL:

Metal connector Motor protective cover Motor Motor propeller Motor protective cover Guide vane PARAMETERS Underwater Jet Battery Case Charger Interface:

Operating Speed: 4-6km/h Low gear : Max. Speed 4km/h High gear : Max. Speed 6km/h Runtime: 1h for low gear, 0.5h for high gear Protective Cover Material: ABS Dimension: 300 x 210 x 110mm (11.8 x 8.3 x 4.3) Weight: 2.5kg (5.5lbs) Rechargeable Battery Pack: 11.1VDC, 8.8Ah/97.68Wh Special lithium-ion battery for BlueDrive S Power Fin Material: watertight, flame retardant ABS Battery Life: 300 cycles Dimension: 210 x 155 x 75mm (8.3 x 6.1 x 3) Net Weight: 1.25kg (2.8lbs) With rechargeable battery, circuit board and 2-in-1 magnetic switch (working as both power switch and emergency stop switch) Input: 100-240VAC,50/60Hz, 1.6A Output: DC12.6V 5A E480809 Full charging time for battery pack is 2~3 hours Metal interface of watertight marine waterproof for plug in Packing Dimension:

62 x 29.5 x 18.5cm (24.4'' x 11.6'' x 7.3'') Packing weight /

Net weight:

5.9 kg (13 lbs) /

4.25 kg (9.4 lbs) Name of component part Picture Quantity

/Unit Remark Underwate Jet Battery Case

(Include Li-ion battery pack) Elastic rope buckle Remote Control Charger Manual 1 Set 1 Set 1 Set 1 Set 1 Set With power cord,plug,fin base and push-in pin With rechargeable battery,circuit board and 2-in-1 magnetic switch(working as both power switch and emergency stop switch) Black elastic rope of 88cm in length with carabiner With arm band, remote control and battery

(CR 2025/CR 2032 3V) Picture shown 1 Copy For American standard PACKING LIST No. 1 2 3 4 5 6 INSTALLATION AND INSTRUCTION 1. Open the packing box and check whether the components are complete 2. Install power fin into Desired device (As shown in the picture) 2.1 Insert the bottom of power fin into the fin base of Desired device;

2.2 Insert the slide in push-in pin into the fin base;

2.1 3. Install the battery case 2.2 Firstly check whether the battery case is with electricity (please refer to the manual of Magnetic Switch for details). If it is or lack of electricity, please charge the battery case in following steps. (As shown in following pictures) Plug in four core a b c d e f a. Insert the power cord of the charger into the corresponding hole position on the charger to charge the battery case. b. Screw off the metal nut on the back of the battery case counterclockwise;

c. Connect the metal plug on the charger to the corresponding connector on the battery case

(Please note the direction of convex and concave corresponding position) and tighten the nut;

d. Plug the power plug of the charger into the home power supply. e. Snap the magnetic switch in the right position of the battery case. And the indicator light on the charger will turn red when it is charging successfully. Please note: the battery case can NOT be charged when it is not connected with the magnetic switch. f. The indicator light on the charger will turn solid green when the battery case is fully charged. After charging, remove the power plug and charger and keep them properly for next charging. 3.1 Put the battery case on the Desired device with the direction of metal plug towards the stern of Desired device;

3.2 Fix the battery by fastening the elastic ropes across the bottom of board respectively and hook them on the 4 corners of battery box. Metal plug towards the stern of ISUP 4. The connection between the power fin and the battery case: screw off the nut lid of the metal plug on the battery case, and insert the metal plug in the end of power line of the power fin into the corresponding metal socket hole of the battery case with correct direction and proper inserting; and tighten the metal nut;

5. Remote control 5.1 Please pull out the insulation layer (a transparent sheet) from the remote control before first use. 5.2 Loading the remote control into waterproof sleeve, and put it on the arm (as shown in the following picture) 5.3 Note: For the remote control, the effective distance is under 10 meters. 5.1 5.4 Operations of Remote Control:

5.2 a. b. c.

: Start and operate at low gear

: Start and operate at high gear

: Stop (Note: This is NOT a start button.) The user can do remote operation on Desired device 5.5 Pairing Operation In most cases, pairing is not needed. When there are over 2 devices, please follow pairing operations as below:

a. Snap the magnetic switch in the right position of the battery case;

b. Simultaneously press these 3 buttons on the remote control untill the indicator light is turned on to enter the pairing mode;

c. When paring is done, the indicator light will flash for 3 times, and the remote control could be used normally. 6. Magnetic Switch Cord 6.1 The magnetic switch cord is a 2-in-1 design, working as both power switch and emergency stop switch. 6.2 For standby mode, snap the magnetic switch in the right position of the battery case, and the indicator light will flash blue for 5 times and turn solid blue to display the remaining battery. The remaining battery is roughly indicated by the number of dots: 4-dot for nearly 100%

battery, 3-dot for nearly 75% battery and so on. 6.3 To shut the battery off, pull out the magnetic switch directly. 6.4 Before each use, always connect the magnetic switch cord with the safety leash. If the red pull cord is removed from the battery case in emergency, the motor will immediately stop to avoid any danger. 6.2 6.4 7. How to Remove Li-ion Battery 7.1 The battery must be removed from the appliance before it is discarded. 7.2 To remove the Li-ion battery, firstly remove 5 screws from bottom base. Then remove 8 screws from the back cover, and the Li-ion battery pack could be easily separated from the battery case. MAINTENANCE Maintenance part Time interval Maintenance process Remote control Every month Underwater jet After each use If you don't use it for a long time, please remove the battery;

Check the residues wrapped in propeller, if yes, please clean it Battery Case After each use Wipe it with a rag and dry it Battery Case In any case The back side of propeller After each use Do not open the battery case by in any cases. Please contact a local dealer or an after-service center for the battery maintenance. Check the residues wrapped in propeller or spindle, if yes, please clean it The connection section of appliances Before and after each use Check whether there is a scratch on the wire, please contact the after service center for replacement if needed;

If there is water mark or other foreign body, please clean it up. DISPOSAL AND ENVIRONMENTAL PROTECTION This marking indicates this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. You can obtain information on disposal from your local authorities. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. No. Problem description The remote control does not work 1 Solutions 1. Check whether the battery is good and loaded properly 2. Check if the insulation layer is removed. 2 3 4 5 The charger does not work The booster does not work The operation of propeller stagnate The booster is with big noise and serious shaking. Check whether the connection of the aviation plug is reliable. 1. Check whether the aviation plug between the motor and the battery case is reliable;

2. Check whether the magnetic switch is assembled. Check the residues wrapped in propeller, if yes, please clean it 1. 2. Check whether there is electricity in the battery case;

3. Check the connection end of the battery case to make sure the connection is reliable and free of debris;

contact after-sale service center;

Check the residues wrapped in propeller, if yes, please clean it 1. 2. Check whether the propeller is destroyed, if yes, please 3. Check whether the screw looses, if yes, please contact 4. Disconnect the power supply and stir the propeller to check after-sale service center;

whether the propeller can turn freely and smoothly; Any obstacle or lock means there is foreign body in the motor, GUIDANCE ON PROBLEMS WARRANTY AND AFTER SERVICE CONTACT INFORMATION 1. Product warranty is 1 year; and it is not within the scope of the warranty for any modification or use beyond the scope of product use, or any damage caused by wrong operation not in accordance with the manual;

2. After-sale service contact Information: www.aquamarina.com

NA aimenene =Oriental Recreational Products(Shanghai)Co.,Ltd Authority to Act as Agent Date: December 24, 2019 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

DEKRA Testing and Certification (Suzhou) Co., Ltd. is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: (Typically 8 ~ 12 months) By: Ain bs Qiang Liu |

(Signature!) (Print name) Title: ___ Manager. On behalf of Oriental Recreational Products(Shanghai)Co.,Ltd

(Company Name) Telephone: 0086-02 1-57402084-8044

'. Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 053019 12 NM mimenien = Oriental Recreational Products(Shanghai)Co.,Ltd Request_for Confidentiality Date: December 24, 2019 Subject: Confidentiality Request for: FCC ID: 2AVFRPF-2408 Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 9,4, the applicant requests that a part of the Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent * Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent *? Users Manual Oriental Recreational Products(Shanghai)Co,,Ltd has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to

"competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __ (specify number of days not to exceed 180)__ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, Manager__ AP ern Qiang Liu

(Signature/Title*) (Print name) By:

2. The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fec.gov/oetcf/kdb/forms/FTSSearchR esultPage.cim? switch=P &id=41731 and review section Il, 3) regarding specific information that must accompany these requests, 3 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentialitypdf for complete details. 4 . Must be signed by applicant contact given for applicant on the FCC site, or by the authorized. agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 053019 - 12

, the applicant requests that a part of the subject FCC application be held confidential.