FCC ID: 2AVFRLED-DC12 Remote Controller

www. t he-m sp a. com ENJOY THE MOMENT OWNERS MANUAL LED Strip with remote control Congratulations on your purchase of MSpa. We are confident that you will enjoy many benefits of using MSpa with the LED strip for years to come. Carefully and thoroughly read this manual before using the product for the first time. For your own safety and that of your equipment, make sure to take the following precautions. Failure to follow the warning notices and instruction may result in property damage, serious injury or death. WARNING SAFETY PRECAUTIONS Do not pull or break the light strip with excessive force when install or disassemble the LED strip to or from the spa pool. Only use the MSpa AC power adapter to connect the LED strip. Be aware of the LED strip chip is not exchangeable or removable. Do not operate the LED strip or connect to the power if the package is unpacked. Be aware of the linear LED strip can only be operated individually. Do not connect the strip with other LED strip. The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the LED strip shall It is recommended to keep the original package or users manual. be destroyed. PRODUCTCONTENTS a) 1 X LED strip b) 1 X AC power adapter C) 1 X remote control Power connection end Picture for reference only. The actual adapters may vary for different regional standards. MODEL&SPECIFICATIONS LED STRIP Item Model Length (m) LED Chips (pcs) LED Strip for D-AU04 LED - 4DC12R LED Strip for U-AU061 LED - 6DC12R 5 5.7 150 171 Power supply: DC12V, 18W (for LED-4DC12R ), 22W (for LED-6DC12R.) IP Rating: IP65 ; Do not put the LED strip into water Lighting Mode: : Colors - Green, blue, lime, white, cyan and purple. Changing every five to six seconds.(for LED-

4DC12R / LED-6DC12R) INSTALLATION properly inflated. 1. Take out the LED strip from the package box, spread it gently. 2. Refer to your MSpa Users Manual for spa inflation. Assemble the LED strip onto spa bottom after the spa pool is 3. Put the spa pool up side down. Make sure the installation location must be free of sharp objects or debris. It is recommended to place a ground mat to protect the spa tub before installation. Connect the LED strip (End point) to the spa bottom beside the control box, either clockwise or counterclockwise is good. 4. Find the PVC connecting channels on the spa pool bottom to secure the LED strip. Starting from either side of the control box, take the end point of the LED strip, make it get trough the PVC channel one by one. Ensure the strip light front side (with the chips) face to the spa pool bottom. Choose either side of the control box to start connecting the LED strip Front side of the strip PVC Channel Front side face to the spa bottom Please note the Power connection end of the LED strip can not be passed through the PVC channel. To help reduce the friction between the LED strip and PVC channel during assembly or disassembly, please gently spray the LED strip with some water before install or uninstall the LED strip. 5. During the installation, make sure the LED strip pass through each PVC channel completely and correctly before to the next PVC channel, no twist or bump. Never pull the strip with excessive force, which will cause damage to the strip and void the warranty. Place the LED strip on the spa bottom and chips face inside the spa for best lighting effect. 6. After passing through all the PVC connection channels smoothly, the LED strip makes an even circle at the spa tub bottom. Now turn the spa tub over and place it on the floor gently. Find the Power connection end of LED strip bottom, and then connect it to the AC power adapter, plug into the outlet and check if the LED strip operates normally. Connect LED strip to the AC adapter Remote Controller SPECIFICATIONS Dynamic mode Static Color PWM Grade Brightness Grade Speed Grade Demo mode Direct Color Select Output Color Switchable Working Voltage Modulation Type Antenna type and Gain Remote frequency Remote distance 22 modes 20 colors 256 levels 5 levels 10 levels Yes Yes Yes, 6 options DC 5~24V ASK PCB antenna,0dBi 433.92MHZ

>15m at open area 1 2 3 4 5 6 11 10 9 8 7 OPERATION Using Remote Controller Pull out the battery insulating tape before using. Install button batteries (not included). Pairing New Remote The light strip and remote controller from the same set have already been paired. To pair light strip to additional or new remote controller, please follow the step below:

1. Unplug the light strip. Plug it back after 5 seconds. 2. Press SPEED+ and SPEED- at the same time and hold for 5 seconds. The pairing is completed. Switch Color Sequence If the direct color button doesn't match output LED light, follow below steps to adjust the light sequences:

1. Unplug the light strip. Plug it back after 5 seconds. 2. Press RED and BLUE button together and hold for 5 seconds. With this operation, the output light sequence will switch between 6 possible combinations. FUNCTIONALITY 1. Turn On / Standby Press the button to turn on the light strip or switch to standby mode. When being powered on, the light strip will automatically turn on and restore to the previous state. 2/9. Dynamic Mode Adjust Switch to dynamic mode from static color, or switch between dynamic modes. 3/10. Dynamic Speed Adjust Adjust the dynamic playing speed. The light will switch to dynamic mode If press this button at static color mode. 4/5. Static Color Adjust Switch to static color mode from dynamic mode, or switch between static colors. 6. Direct Color Select Select static colors directly. When press the specific color button, light strip will play the same static color. The direct colors are included in COLOR+ and COLOR- operation. 7/8. Brightness Adjust Adjust static color brightness. The light will switch to static color mode If press this button at dynamic mode. 11. Demo Mode Press this button will switch to Demo mode. At demo mode, it plays 17 dynamic modes in loop, each mode repeats 3 times. FCC/IC COMPLIANCE / TM / WARRANTY This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help ORIENTAL RECREATIONAL PRODUCTS (SHANGHAI) CO., LTD ADDRESS: No. 1699 DaYe Rd, Wuqiao, FengXian District, Shanghai, China 201402 PHONE: +86-21-57402084 FAX: +86-21-57401306 E-MAIL: info@the-mspa.com

Oriental Recreational Products (Shanghai) Co., Ltd. No 1699 DaYe Road WuQiao FerigXian ShangHai P. R. China Authority to Act as Agent Date: Nov 16, 2020 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

Intertek Testing Services Shanghai__is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: May 29, 2021

- By: _A wthion 4. Qiang Liu Signature?) - (Print name) Title: . Quality assurance Manager On behalf of: Oriental Recreational Products (Shanghai) Co., Ltd.

(Company Name) Telephone: 0086-021-57402084-8044 1. Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Oriental Recreational Products (Shanghai) Co., Ltd. No 1699 DaYe Road WuQiao FengXian ShangHai P. R. China Request for Confidentiality Date: _Nov 16, 2020 Subject: Confidentiality Request for: FCC ID: 2AVFRLED-DC12 _ IC :26710-LEDDC12) Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 12.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit

[|] Short Term Permanent Block Diagrams

[|] Short Term External Photos

[_] Short Term [] Permanent*! Internal Photos _] Short Term Permanent Operation Description/Theory of Operation

(_] Short Term [_] Permanent Parts List & Placement/BOM L] Short Term [_] Permanent Tune-Up Procedure L_] Short Term Permanent Schematics

[_] Short Term Test Setup Photos

[] Short Term [_] Permanent*? Users Manual Oriental Recreational Products (Shanghai) Co., Ltd. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __ (specify number of days not to exceed 180 __ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By: tote! Qiang Liu

(Signatur e/Title*) (Print name)

- The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for DO1 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section Il, 3) regarding specific information that must accompany these requests. 2 . Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality. complete details.

- Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. df for