OWMH-DS6311-01 Product Specification Version:0.1 Date: 2018.11.14 OWMH-DS6311-01 Product Specification Version Issue date Changes Remark 2018/11/14 Initial Version 0.1 IMPORTANT should not be disclosed to third parties without prior written consent of ORing Industrial Networking Co. Ltd. This document contains important Information and therefore Signature:
Author:
Rino Pan Reviewed by:
Approved by:
Remarks:
Page 1 of 8 OWMH-DS6311-01 Product Specification Version:0.1 Date: 2018.11.14 1. Introduction OWMH-DS6311-01 module is designed for easy-design-in low cost and suitable for Wi-Fi applications. The module can support WAN, LAN, UART, SPI, I2S, SDXC and GPIO interfaces and work for 2T2R mode. 2. Technical specification Items Specification Supported Standard and Protocol IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.11a, IEEE 802.3, IEEE 802.3u, CSMA/CA, CSMA/CD, TCP/IP, DHCP, ICMP, NAT, PPPoE Dimension Power consumption Operating Temperature Range Storage Temperature Range LAN RF Parameters WAN Port LAN Port Frequency Range Baud Rate 80x70x1.6mm
< 350mA
-30 ~ 75 deg. C
-40 ~ 85 deg. C 4 x 10/100M adaptive RJ45 port 1 x 10/100/1000M adaptive RJ45 port 2.4~2.4835GHz 5.180~5.240 GHz & 5.745~5.825 GHz 1T1R:
MCS index Data rate (Mbit/s) 20 MHz channel 40 MHz channel 800 ns 400 ns 800 ns 400 ns 0 1 2 3 4 5 6 7 6.5 13 19.5 26 39 52 58.5 65 7.2 14.4 21.7 28.9 43.3 57.8 13.5 27 40.5 54 81 108 65 121.5 72.2 135 15 30 45 60 90 120 135 150 2T2R MCS Data rate (Mbit/s) Page 2 of 8 Number of Channel Modulation Scheme Sensitivity @
PER Output Power OWMH-DS6311-01 Product Specification Version:0.1 Date: 2018.11.14 index 20 MHz channel 40 MHz channel 800 ns 400 ns 800 ns 400 ns 8 9 10 11 12 13 14 15 13.00 26.00 14.40 28.90 27.00 54.00 30.00 60.00 39.00 43.30 81.00 90.00 52.00 57.80 108.00 120.00 78.00 86.70 162.00 180.00 104.00 115.60 216.00 240.00 117.00 130.00 243.00 270.00 130.00 144.40 270.00 300.00 IEEE 802.11g54/48/36/24/18/12/9/6(adaptive) IEEE 802.11b11/5.5/2/1M (adaptive) 13 DBPSKDQPSKCCK and OFDM(BPSK/QPSK/16-QAM/64-QAM) 802.11a: -92dBm 2dBm@6Mbps, 802.11a: -76dBm 2dBm@54Mbps 802.11b: -98dBm 2dBm@1Mbps, 802.11b: -85dBm 2dBm@11Mbps 802.11g: -76dBm 2dBm@54Mbps 802.11gn HT20: -75dBm 2dBm@MCS7, 802.11gn HT40: -72dBm 2dBm@MCS7 802.11an HT20: -74dBm 2dBm@MCS7, 802.11an HT40: -71dBm 2dBm@MCS7 802.11a: 24dBm 1.5dBm@6Mbps, 802.11a: 12dBm 1.5dBm@54Mbps 802.11b: 23dBm 1.5dBm@1Mbps, 802.11b: 17dBm 1.5dBm@11Mbps 802.11g: 16dBm 1.5dBm@54Mbps 802.11gn HT20: 15dBm 1.5dBm @MCS7, 802.11gn HT40: 14dBm 1.5dBm @MCS7 802.11an HT20: 12dBm 1.5dBm @MCS7, 802.11an HT40: 11dBm 1.5dBm @MCS7 Antenna Two IPEX I connectors for two external antenna(2T2R) WIFI Operation Mode AP/Client/Repeater System Service Virtual ServerInternal web server for browser to access Area setting Restore to default factory setting Software upgrade Reboot Device Management Page 3 of 8 OWMH-DS6311-01 Product Specification Version:0.1 Date: 2018.11.14 WLAN Security Mode Change password OPENWEP SHAREDWEP WEPAUTO WPA WPA-PSK WPA2 WPA2-PSK WPAPSKWPA2PSK WPA1WPA2(WPA and WPA2 hybrid mode) 802.1x 3. Software features Support APAccess pointClient (Wi-Fi Station) modeRepeater(AP-Client) mode AP mode o Default operation mode. In this mode, the module work as an Access Point, don't need any configuration. o User can use PC via RJ45 or smart phone via Wi-Fi to login AP mode and change the default configuration (through browser). Client mode o In this mode, module is a Wi-Fi station. Repeater mode o In this mode, module is AP + Client mode. 4. Development tool:
We provide development tool for easy connection of power, RS-232, LAN, WAN, and USB port. Page 4 of 8 OWMH-DS6311-01 Product Specification Version:0.1 Date: 2018.11.14 5. Module Dimension: 80x70x1.6mm Page 5 of 8 OWMH-DS6311-01 Product Specification Version:0.1 Date: 2018.11.14 6. Pin Assignment J1:
Description Function Pin # Pin #
Function Description 5V input 5V input 5V input 3.3V input 3.3V input 3.3V input Power ground 5V 5V 5V 3.3V 3.3V 3.3V GND Media-dependent interface A TXVPA Media-dependent interface A TXVNA Power ground GND Media-dependent interface B TXVPB Media-dependent interface B TXVNB Power ground GND Media-dependent interface C TXVPC Media-dependent interface C TXVNC Power ground GND Media-dependent interface D TXVPD Media-dependent interface D TXVND Power ground for 10/100 BASE-T link for 1000 BASE-T link for 10/100/1000 BASE-T activity Power ground GND GND LED_10_100 LED_1000 LED_ACT 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 2 4 6 8 10 12 5V 5V 5V 3.3V 3.3V 3.3V 14 GPIO21 16 GPIO22 18 GPIO18 20 GPIO20 22 GPIO19 24 GPIO0 26 GPIO1 28 GPIO2 30 GPIO3 32 GPIO4 5V input 5V input 5V input 3.3V input 3.3V input 3.3V input LED_LAN_LINK NA LED_SIM1 LED_LAN_ACT LED_SIM2 LED_STATUS LED_WLAN NA NA LED_WAN 34 36 38 40 42 44 46 PCIE_RST_OUT PCI Express reset PCIE_TX_N PCIE_TX_P PCIE_CLKOUT_N Differential reference clock PCIE_CLKOUT_P Differential reference clock Differential transmit Differential transmit PCIE_RX_N Differential receive PCIE_RX_P Differential receive J2 :
Description Function Pin # Pin # Function Description Tx positive for port 1 Tx negative for port 1 Rx negative for port 1 Rx positive for port 1 Rx positive for port 0 Rx negative for port 0 Tx positive for port 0 Tx negative for port 0 USB signal poistive USB signal negative P1_TX+
P1_TX-
P1_RX-
P1_RX+
P0_RX+
P0_RX-
P0_TX+
P0_TX-
USB_D+
USB_D-
1 3 5 7 9 11 13 15 17 19 2 4 6 8 GND Power ground GPIO11 LED_WLAN_RSSI1 SW_RESET Software reset GPIO17 Power ON/OFF 10 GPIO15 LED_WLAN_RSSI3 12 GPIO12 LED_WLAN_RSSI2 14 GPIO16 SIM_SEL 16 18 UART_TXD UART TXD signal UART_RXD UART RXD signal 20 GND Power ground Page 6 of 8 OWMH-DS6311-01 Product Specification Version:0.1 Date: 2018.11.14 GPIO Signal Description (Default) Direction IDS-6311GTH+ GPIO Signals pin define GPIO0 LED_STATUS GPIO1 LED_WLAN GPIO2 NA GPIO3 NA GPIO4 LED_WAN GPIO5 SPI_nCS GPIO6 SPI_CLK GPIO7 SPI_MOSI GPIO8 SPI_MISO GPIO9 UART_Rx GPIO10 UART_Tx TCK TDI TDO TMS CLK_OBS5[1]
SPI_CS SPI_CLK SPI_MOSI SPI_MISO UART0_SIN UART0_SOUT GPIO11 LED_WLAN_RSSI1 Output Software configurable GPIO12 LED_WLAN_RSSI2 Output Software configurable GPIO13 INT_9344 for AR8035 interrup Output Software configurable GPIO14 SW default reset Output Software configurable GPIO15 LED_WLAN_RSSI3 Output Software configurable GPIO16 SIM_SEL Output Software configurable GPIO17 Power ON/OFF Output Software configurable GPIO18 SIM1_LED GPIO19 SIM2_LED Output Software configurable Output Software configurable GPIO20 LED_LAN_ACT Output Software configurable GPIO21 LED_LAN_LINK Output Software configurable GPIO22 NA Output Software configurable Input Input Output Input Output Output Output Output Input Input Output Output Output Input Input Input Output Input Output Output Output Output Output Page 7 of 8 OWMH-DS6311-01 Product Specification Version:0.1 Date: 2018.11.14 7. Memory configuration Depending on customer's request, the module can be shipped with following configuration:
Flash size: 8MB, 16MB NOR Flash DDR2 size: 64MB, 128MB 8. Mechanical Application Notes 1. CON0 and CON1 are IPEX1 connectors on top side 2. 3. J1 is 2*23 pins 1.27mm female header on bottom side for signals J2 is 2*10 pins 1.27mm female header on bottom side for signals 4. The mechanical drawing in .dxf format is available under request. 9. Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3. External antenna Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC Part15C/E & Canada limit and is prohibited. 10.Compliance FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Device cannot be sold via retail to the general public or by mail order; it must be sold to authorized dealers or installers only. Page 8 of 8 OWMH-DS6311-01 Product Specification Version:0.1 Date: 2018.11.14 FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in visible area with the following: Contains FCC ID: WHD-OWMDS6311-01 End Product Manual Information The user manual for end users must include the following information in a prominent location IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization. This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users. As long as a condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). Page 9 of 9