Oro Technology Co., LTD Tire Pressure Monitoring System Model : WT01 ORO WT01 TPMS Manual To ensure correct operations and services please read these instructions before installing and operating the TPMS NOTICE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 1 ORO WT01 TPMS ORO-WT01 Tire Pressure Monitoring Systems (TPMS), can monitor and provide tire pressure, tire temperature and car battery information in real time to help the driver control and keep the normal tire pressure in order to reduce the fuel consumption and extend the tire life, and also through the battery information, the driver can change the battery before any incident occurs and reduce the possibility of vehicle breakdown on the roads. ORO-W401 Tire Pressure Monitoring System, includes maximum 11 tire sensors and 1 receiver display, the TPMS can monitor the pressure/temperature by snap-in installation into the tire, and transmit the tire information to the receiver by wireless. The TPMS display will trigger an alarm when any abnormalities happen to the tire in order to prevent any possible accidents which may happen to the driver/vehicle. WT01 TPMS Specification 1.. Transmitter Module Specification 3 V Power Supply Operating Humidity Max 95 %
-40 to 125 Storage Temperature Operation Temperature
-30 to 115 Max 71 dBuv/m Transmitting Power 433.92 MHz Transmitting Frequency Pressure Monitoring Range 0 ~ 203 psi (or 0 ~ 14 bar) 4 psi (0.27 bar) @ -20~850.3bar Pressure Reading Accuracy
-30 to 115 Temperature Monitoring Range Temperature Reading Accuracy 3 10g 1g Module Weight 2. Receiver Module Specification Power Supply Operating Humidity Operation Current Storage Temperature Operation Temperature Pressure Display Range Temperature Display Range DC 9V ~ 36V Max 95 %
100mA
-30 to 80
-20 to 70 0 ~ 13 bar
-40 to 115 2 WT01 TPMS Accessories Accessories QTY Display Power Cable Antenna Antenna Holder Adjustable Multi Angle Holder 1 1 1 1 1 Battery Accessories QTY 11 11 11 1 Tire Sensor Lock-Nut Spanner Manual 1 Cable tie 10 3 WT01 TPMS Installation 1. Tire Sensor Installation Step Operation Process Photographs a Take off the 11 tires and mark 1~11 for each tire position. b Install CR1632 Battery into Tire Sensor c Insert the Lock-Nut into the valve. d Tighten the Tire Sensor and use the spanner to lock the Lock-Nut back to the Tire Sensor and complete the installation. This product is recommended with metal valve or replace the original valve regularly to ensure better quality. 4 3M adhesive 2. Display Installation New adjustable multi angle holder (STANDING TYPE) assemble manual:
New adjustable multi angle holder (PASTE TYPE) assemble manual:
Upon decided where to paste, tear out 3M adhesive from the base and stick on the holder. The user can decide to use the adhesive in the box or 3M double side adhesive:
NOTE The display (STAND and PASTE type) shall be 180 degree reverse up and down with opposite direction when is using 3M double side adhesive. The display and holder still can be separated or combined when the user is using 3M double side adhesive:
Step 2: Push the display backward to the bottom and 3M double side adhesive Velcro Step 1: Use the fingers to fix the back side of the holder. 5 a. Firmly secure the magnetic holder in a suitable place. (Suggested place as shown in the picture) b. Put the display on the magnetic holder. c. Keep 20cm of distance from GPS; digital TV; speed measure device or other automotive electronic devices while are installing TPMS in order to prevent any possible of interference. d. Please solder the red cable to the AC power, the black cable is for grounding. 6