Universal Kit nNR universal kit suits any spout diameter between 22mm and 32mm as it includes 4 grip kits. Choose your grip kit according to the table below:
Nozzle Model Grip Kit**
Set Screws*
Husky 1A Husky X OPW 11 A/B Leaded OPW 11 A/B Unleaded OPW Avance HS/VR OPW DEF Tatsuno Leaded Tatsuno Unleaded ZVA 25 ZVA DEF ZVA Slim Line ZVA S.L. 2-GR
*Use 10mm set screws when spout diameter is 22mm or below.
** The 32mm grip kit includes only a two-pieces top lid instead of two lids. 30 27 30 27 32 27 30 27 32 24 30 30 6 6 6 6 6 6 6 6 6 8 6 6 Watch nNR Installation Tutorial Specications Parameter Supply Voltage Power Consumption Operating Temperature Storage Temperature IP Rating Dimensions (HxWxD) Weight Communication Interface Hazardous Area FUELING YOUR BUSINESS FOR SUCCESS nano Nozzle Reader Assembly Guide Value 3.6 internal battery pack P/N 812560010 Active Mode: 160mA Standby Mode 20 A
-40 to +60 C
-40 to +85 C IP 67 41x84x60.5mm 132g RF to WGT: 2.405-2.480GHz Typical transmission power: 3dbm (2mW) RFID to FuelOpass: 108-131 kHz Zone 1 Explosive atmosphere (Ex) ia (intrinsic safety) protection level Group IIC type product Temperature Class: T6 Rated Temperatures:-40<Tamb< +60 C P
N 8 1 7 4 6 0 0 0 5 FCC Compliance Statement Warning The FCC Wants You to Know:
This equipment has been tested and found to comply with the limits for a Class A
& B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :
a) Reorient or relocate the receiving antenna. b) Increase the separation between the equipment and receiver. c) Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. d) Consult the dealer or an experienced radio/TV technician. Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with FCC Rules Part 15 and with Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes
:(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Installation Kit 9 8 7 6 5 3 4 3 1 2 1 5 3 3mm 7 2mm
# Part Name Part Number Qty. 1 Set Screws 815221300 (6) 815221380 (8) 815221310 (10) 2 Spout Adaptor 814360500 3 Lids 814360424 (24) 814160427 (27) 814160430 (30) 814360700 (32) 4 Rubber Filler 814160024 (24) 814160027 (27) 814160030 (30) 814160032 (32) 5 M4 Screws 815213424 6 nNR Assembly 819260000 (nNR)/819260100(nNR + Switch) 7 M3 Screws 815260300 8 Front Cover 814360200 9 M3x6 Screws 815260200 Required Tools 4 1 2 1 4 1 4 1 2 Slide the adaptor over the spout. Place it as close as possible to the nozzle body Secure the gip kit with the M4 screws. Tighten them in stages and in a diagonal sequence. Use a 3mm head ratchet Slide the nNR assembly over the spout Place the nNR front cover on top of the assembly. Secure with the M3 screws. Use a 2mm Allen key 2 4 6 8 2mm 2mm Choose the proper grip kit for the nozzle
(see rear table). Place a lid, the rubber ller and then the other lid Apply glue and place the set screws in the adaptor corners. Use a 2mm Allen key Secure the nNR to the adaptor with the M3 screws. Use a 2mm Allen key Program the unit 3mm Allen head ratchet
(not ball ended) 2mm standard Allen key
(not ball ended) Loctite 222/
Holdtite T43 glue Installation Notes Unit should be serviced only by authorized service personnel. Opening of the unit by Service Personnel must not be done at the location of installation. When replacing the battery, use only P/N 812560010.