FCC ID: DZO-OSREFRMG13W iQ ZigBee RF Controller

iQ ZigBee RF Controller User Manual Status: Draft Date 02/09/2018 1. Introduction:

iQ ZigBee RF Controller board is designed for Osram internal use only. To explain further, this RF controller board can be integrated into any Osram end products such as LED Lamp, Power Supply for LED, Electronic Ballast or Luminaires. However, this RF Controller board is NOT meant to be sold to third parties. production documentation Specification of this RF Controller board is presented in Table1. Table 1: RF Module specification Parameter Description PHY and MAC layers transceiver Max RF TX Power (EIRP) sensitivity Operating temperature range Supply voltage RX current (+10dBm) TX current (+0dBm) Description iQ ZigBee RF Controller 2.4GHz IEEE 802.15.4-2003

+10dBm

-102.7dBm

-40 to +85C 2.1 to 3.6V 10.2 mA 8.5 mA (typical) MCU core flash RAM peripherals 32 bit ARM Cortex M4 up to 40MHz with AES128 encryption accelerator 512 kB (EFR32MG13P632F512GM48) 64 kB UART, SPI, I2C, ADC, Timers, GPIO Deep sleep mode current consumption

(Mode EM4S) PCB size Agency Approvals FCC #

IC#

Bill of Material# (Internal EDOS#) EFR MG13 Radio Part# (Internal EDOS#) Whisker Antenna Part# (Internal EDOS#) Schematic # (Internal EDOS#) PCB Layout# (Internal EDOS#) 85nA (typical) 12.9x18.0mm FCC, IC DZO-OSREFRMG13W 23566-OSREFRMG13W D30042085 D30042186 D30042184 2D1-3621942 1Q1-3621940 2. Warning Changes or modifications not expressly approved by R&D Director of Osram could void the users authority to operate this equipment. This is due to FCC or IC requirements. 3. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may iQ ZigBee RF Controller User Manual Status: Draft Date 02/09/2018 cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

production documentation Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 4. Industry Canada Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. WARNING! This module is to be installed only in OSRAM end products by their personnel, and shall not be offered to 3rd party OEM integrators or the general public. This RF Module has been certified for integration into products without further testing or certification. However, OSRAM is still responsible for testing their end-product for any additional compliance requirements required with this module installed (such as digital device emissions, PC peripheral requirements, etc.). iQ ZigBee RF Controller User Manual Status: Draft Date 02/09/2018 5. End Product Labeling Requirements The following statements shall be placed in the manual of the end product as this RF Controller board is considered extremely small (~8 x 10cm). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. production documentation The final end product must be labeled in a visible area with the following:

Contains Transmitter Module FCC ID: DZO-OSREFRMG13W Contains Transmitter Module IC: 23566-OSREFRMG13W OR Contains FCC ID: DZO-OSREFRMG13W Contains IC: 23566-OSREFRMG13W OR similar wording. 6. End Product User Manual Requirements The user manual for the end product must include the following information in a prominent location:

To comply with FCC and Industry Canada RF radiation exposure limits for general population/uncontrolled exposure, the antenna(s) used for this transmitter must be installed such that a minimum separation distance of 20cm is maintained between the radiator (antenna) and all persons at all times. In addition this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter. IMPORTANT NOTE: In the event that these conditions can not be met (for certain configurations or collocation with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number can not be used on the final product. In that case the end product must be re-evaluated to obtain separate FCC and Industry Canada authorizations. This device has been designed to operate with an antenna that is described under EDOS#

D30042184. This antenna has a maximum gain of -0.47 dBi. Antennas not included in this list

(EDOS# D30042184) or having a gain greater than -0.47 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.

FCC: DZO-OSREFRMG13W IC: 23566-OSREFRMG13W FCC: DZO-OSREFRMG13W IC: 23566-OSREFRMG13W FCC: DZO-OSREFRMG13W IC: 23566-OSREFRMG13W

FCC ID: DZO-OSREFRMG13W IC: 23566-OSREFRMG13W

ew otams OSRAM Operates with ENCELIUM (R) EXTEND Operating Voltage: 12.200 Class 2 only AnbinTenpermaeTa6eCmax Gp Contains FCC WD: DZO-OSREFRMGIN Contains IC: Z3566-OSREFRUGIIN

OSRAM Pee OCs arate Ten?

iPthe device is subject to Cactitieation: (1) Secton 2.925 contains information on identification of the eipulpment: (2) include a label beartag an ECU Tdeatitier (FCC ED) (Seetion 2.926) and (9) include the appropriate compllaace statement in Section (3.09). [the labelling area is cousklered too small and therefore 118 imapractical (smaller than the palm ofthe hand) to display the compliance statement, then Ci RTC LULL See SCROLL MERA MOR TLaL mere reels iol Ges rehe: ert Mame gk CCLC con comm LL TOG COM A CDMCAL Gt MeL ELE VETS OreO GEC Ms o Ge OU COMBE CLOMG OAZISSM MOTI LUC GCL CTe Lp Om COCCI Ce Tacs Loe OO UP ROR se sm es ECs] eb GTUUEste Comet rate maar Oo OOL (OL Aco Mace] (0mm ox ON GUN OBST TE rome sTocert MIC CeLemE csr MmD ATES AT) Mmm GlOLy aeLah MME T@T TTR] MO LOme Cerrar pte Le that the device itselfis too small the label area allocated to the FCC CO may not be rediteed because of over crowded identification of other product and regulatory tormation. Justification tor placing the OL CML O Memes CominltiLC li iienia cromih slittiicora ey ar ciMmaacomceULecau Mri avenOLecau die lO Mm Ce) aro brme a Coritdceli Mm CP LMe Cen az Cen nmr vaL SIRI EOh ALLE en aa ener COT a et ie es eae ene bac abserud GPs ieee eteaedtes eeceeee eed beer neiniieh loaover Ce eee OO Os Ce 7 nh ali ven Cae LAS | eee ed a Justification for the module itself not having label KDB 784748 DO1 Labelling Part 15 & 18 Guidelines v08 section 2.2 (as shown below) provides guideline about labelling requirement of the module. 2,2 Certification Fem C9 a

~ A 4 Tn para e te ie wa OY aot

- aera ing ee ria ie ea eee aie Com ance state ie eeeeae eect ae Ie: as oe afore if is een coe wan tne palm oftne hanc: ta disn: = 8 jee erates slate. Rida in the user tanual or product packegine. Mowever, the device mu ae a (the device is one een gery eee Fine i on FCC a a ears ee ah aor rc een oe ~ . TnL Ons bat " Seo MEd. Aaaes ne bee Es jelerminsc he F ir eB Beer eee sb oy eC Ty visitor ern on ne must he submitted w m abies. ar) The overall dimension of the module is 12.9mm (width) x 18.00mm. This information is provided in various documents such as User_Manual_Verl.pdf. Module is definitely smaller than palm of the hand and hence it is not possible to have compliance statement. However, such statement is placed in user manual of the module

(User_Manual_ Verl.pdf - section 5 and_ section6) as well in end _ product manual

(End_Product_User_Manual_Verl1.pdf). Regarding label on the module itself, the word FCC ID: DZO-OSREFRMG13W in font size 4 takes up about 19mm. The module size is 18mm in length and width is only 12.9mm. Hence, it is not possible to have label with FCC ID on the module itself. Clinets signature Name: Marianne Kotubetey Title: Senior Attorney Address: 200, Ballardvale Street, Wilmington, MA 01887 Telephone: 978-570-3313 Date: February 26, 2018 OSRAM SYLVANIA 200 Ballardvale Street Wilmington, MA 01887

@ (978) 570-3000 www.osram-americas.com

OSRAM FCC Authorization & Evaluation Division 7435 Oakland Mill Road HUT E mE ase maT I, Marianne Kotubetey, counsel for OSRAM SYLVANIA Inc., do hereby authorize, until further notice, Bureau Veritas Consumer Products Services, Inc., Littleton Distribution Center, One Distribution Center Circle Suite#1, Littleton, MA 01460, to act on our behalf in dealings before the Federal Communications Commission with respect to all matters relating to equipment authorizations under 47 CFR. This authorization includes, but is not limited to, the signing of Form 731. I certify that no party (as defined in 47 CFR 1.2002) to this application, including myself, is subject to a denial of federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 853A. Certified By:

Name: Marianne Kotubetey PBL aUieyniony Telephone: 978-570-3313 Date: October 22"4, 2019 OSRAM SYLVANIA 200 Ballardvale Street Wilmington, MA 01887

@ (978) 570-3000 www.osram-americas.com LETTER OF AUTHORIZATION

OSRAM Aba reavneteacoyeMM\y AN October 22, 2019 FCC Authorization & Evaluation Division 7435 Oakland Mill Road Columbia, Maryland 21046 Subject: C2PC for FCC ID: DZO-OSREFRMG13W To whom it may concern This is to request a Class II permissive change for FCC ID: DZO-OSREFRMG13W granted on 02/27/2018. The major change filed under this application is:

1. Enable Bluetooth Low Energy (BLE) operation of the radio. Such operation will be time multiplexed with previously approved functionality i.e., Zigbee operation. If you have any questions, please feel free to contact me. Sincerely Yours Name: Marianne K a SPU ars UO Telephone: 978-570-

Date: October 22", 2019 OSRAM SYLVANIA 200 Ballardvale Street Wilmington, MA 01887

@ (978) 570-3000 www.osram-americas.com

OSRAM Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046-1609 Curtis-Straus LLC 1 Distribution Center Circle, #1 Littleton, MA 01460 Confidentiality Request Gentlemen:

This letter is to comply with 47 CFR 0.457(d)(2) pertaining to confidential material. Osram Sylvania Inc., requests that the following documents regarding this submission for FCC ID DZO-OSREFRMG13W be kept fey ivakelss Nat B Sytem Velour Schematics Block Diagram Specification of Whisker Antenna Peak Gain data for Whisker Antenna i?

ye ee ue Circuit/Technical Description 5. oe 7. Gerber File of PCB illustrating connection between radio module and whisker antenna The material above contains technical data, which would customarily be guarded from competitors. Sincerely, Name: Marianne L. Kotubetey, Esq. SU HN tineeilo Telephone: 978-570-3313 Date: February 26, 2018 OSRAM SYLVANIA 200 Ballardvale Street Wilmington, MA 01887

@ (978) 570-3000 www.osram-americas.com Request for Confidentiality for FCC February 26, 2018

ZigBee Module FCC ID : DZO-OSREFRMG13W is seeking FCC Authorization as a LJ Single Modular transmitter / [x] Single Limited Modular Approval (please check one). The EUT meets the requirements for a LD) Single Modular transmitter

/ [x] Single Limited Modular Approval (please check one) as detailed in FCC Public Notice DA00-

1407. Compliance to each of the requirements is described below:

Remarks: This module will NOT be sold to third parties. it will be used only within Osram end 1. The modular transmitter must have its own RF shielding aera 2. ~The modular transmitter must have buffered modulation / data inputs Yes OC. No 3. The modular transmitter must have its own power supply regulation ae f--te ete Remarks: Radio !C has internal regulator at Vcc pin to take any input voltage between 1.8V and 3.8V. Hence, end product (host) may require an additional power supply regulation to provide Vec to the module in this range. 4. The modular transmitter must comply with Antenna requirements of section 15.203 and

| mrs tT Ca) bree 5. The modular transmitter must be tested in stand-alone configuration Sa Core eile 6. The modular transmitter must be labeled with its own FCC ID ae reel Remarks: In the test setup, the module is placed on an another daughter board that has externa!

antenna mounted. Remarks: The module is very small in size. Hence, per 2.925, jabe! with modules FCC ID is locatec in host manual and in label of the host. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacture must provide adequate mstruction along with module the module to explain any such requirements i fe fe The modular transmitter must comply with any applicable RF exposure requirements Yes /O No Questions are:

February 26, 2018 Note:

Limited Modular Approval (LMA) may be granted when one or more of the requirements in the table above can not be demonstrated. LMA will also be issued in those instances where applications can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition of the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product into which the module will be installed, and will be maintained, such that full compliance of the end product is always ensured.

(2) Host devices which contain separately certified modules do not need to be recertified, provided that they meet the following conditions:

i. The host device, as a stand-alone unit without any separately certified modules, complies with all applicable Radio Standard Specifications. 11. The host device and all the separately certified modules it contains jointly meet the RF exposure compliance requirements of RSS-102, if applicable. ii. The host device complies with the certification labeling requirements of each of the modules it contains. Note 1: Compliance of a module in its final configuration is the responsibility of the applicant. A host device will not be considered certified if the instructions regarding antenna configuration provided in the original description, of one or more separately certified modules it contains, were not followed. Example: A separately certified low-power transceiver module using Bluetooth technology which is housed in a desktop computer, laptop or peripheral does not require the overall system to be recertified, if the desktop computer, laptop or peripheral, as a stand-alone unit, complies with all applicable technical standards. OTT Taree Name: Marianne Kotubetey Siro loaatiKeutlons Address: 200, Ballardvale Street, Wilmington, MA 01887 Telephone: 978-570-3313 Date: February 26, 2018 Limited Modular Approval (LMA) Declaration Letter We, (OSRAM SYLVANIA Inc.,) declare that we will retain contol over the final installation of the device, (FCC ID: DZO-OSREFRMG13W) such that compliance of the end product is assured. In such cases, an operating condition on the LAM for the module must be only approved for use when installed in devices produced by a specific manufacturer. OTM eh ae Name: Marianne Kotubetey SBN a ileyapatnKoyuilay Address: 200, Ballardvale Street, Wilmington, MA 01887 Telephone: 978-570-3313 Date: February 26, 2018

OSRAM GEV oa Oe eR mPa k) KDB 996369 D02 V01 discusses (Q11) requirements to be met by a module that seeks for certification with requirement that host device must use micro strip as antenna. This declaration explains how those requirements are met by this module. 1. This module can be used only within Osram i.e., it can not be sold to third parties. 2. Strict guideline for micro strip design are provided in Technical Description Verl.pdf section 7. Approved antenna is also presented in this section. Micro strip to use as antenna in host board is also shown in an example with gerber files. Test procedure to verify proper intergration of module onto a host board with micro strip as antenna is detailed in Technical_Description_Ver1.pdf section 8. Similarly test procedure to verify during production of host board is spelt out in Technical_Description_Ver1.pdf section 9. OTM Tae

~Name: Marianne Kotubetey Title: Senior Attorney Address: 200, Ballardvale Street, Wilmington, MA 01887 Telephone: 978-570-3313 Date: February 26, 2018 OS EOD A mahal 200 Ballardvale Street Wilmington, MA 01887

@ (978) 570-3000 www.osram-americas.com

OSRAM SYLVAl IA LIGHTING SOLUTIONS I, Marianne Kotubetey, counsel for OSRAM SYLVANIA Inc., do hereby authorize, until further notice, Curtis-Straus LLC, Littleton Pel EO EO Bele Ce ee eRe EC Ue mee Ramee hice cel Communications Commission with respect to all matters relating to equipment authorizations under 47 CFR. This authorization includes, but is not limited to, the signing of Form 731. I certify that no party (as defined in 47 CFR 1.2002) to this application, including myself, is subject to a denial of federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 853A. Certified By:

Name: Marianne Kotub BRO te lg Telephone: 978-570-3313 Date: January 29th, 2018 LETTER OF AUTHORIZATION FCC Authorization & Evaluation Division 7435 Oakland Mill Road Columbia, Maryland 21046 ES AYU eps Ty Une auc) 200 Ballardvale Street Se CAL La CELE Seu