FCC ID: 2AI7B-Q26A LED Table Lamp with Wireless Charger

E ENGLISH Ryan LED Desk Lamp with Wireless Charging CONGRATULATIONS!

Youve purchased the finest in natural lighting technology with your new OttLite product. CAUTION! THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED. PRODUCT REGISTRATION FORM Please complete the enclosed Product Registration Form and return it today by mail, or register online by going to: OttLite.com/warranty CAUTION: Any change or modification to product not expressly recognized by OttLite Technologies voids OttLites responsibility for proper function of product. WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps are complete. FCC PART 15 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION:

To maintain compliance with the FCCs RF exposure guidelines, place the product at least 20cm from nearby persons. POWER ADAPTER SPECIFICATION:

Input: AC 100-240V, 50/60 Hz, 0.5A Output: 5V DC, 2.0A with a Male DC Plug Qi CHARGER SPECIFICATION:

Output: 5V, 1A or 5 watts NOTE: THIS UNIT IS FULLY ASSEMBLED 1. Remove lamp from packing, placing lamp body base (A) flat on a steady surface. 2. Connect power adapter input (B) into connector (C) in the rear-bottom of the lamp. 3. Plug the power adapter (D) into a standard household 120V AC outlet. Note: Only use with the supplied power adapter to avoid damage or fire. 4. Turn the lamp ON/OFF using touch switch (G) located on top of base (A). 5. This lamp provides three brightness settings. To adjust the brightness of the lamp, touch switch (G) on top of base (A). 6. This lamp provides three color modes. To adjust light color mode, press and hold switch (G) to change light color temperature. 7. Wireless charger (F) is located in the center of base (A). See Wireless Charging Instructions section for details. 8. To reposition the light, hold base (A) steady and grasp shade (E) to adjust position. DO NOT FORCE the shade or lamp body outside allowable adjustable range as excessive adjustment may cause damage. WIRELESS CHARGING INSTRUCTIONS:

To wirelessly charge a device, perform the following:

Place the device, which supports wireless charging, face up on the middle of the wireless charging icon (F). When the device is centered on the wireless charging icon (F) check the device to ensure it is charging properly. Check the charge level on your device periodically to determine when device is fully charged. NOTE: Lamp DOES NOT provide any indication of when device is fully charged. CAUTION! DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE. SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS 1. Turn lamp off and WAIT UNTIL LAMP HEAD (E) IS COOL before handling. 2. The LED panel might get hot after several hours of continuous use DO NOT place your hands directly on LED light panel. 3. Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord. 4. Do not alter the plug. 5. The lamp head included with this unit cannot be replaced by the consumer. 6. INDOOR USE ONLY. NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product. CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY. D C A B F G Ryan LED Desk Lamp with Wireless Charging 3WCG59 3WC009 INS210674 Q26A REV011922

aeOttLite

| ITEM/MODELE: Q26A |

LED 4W,INPUT/ENTREE DC 5V==-2A USA TEL: 800-842-8848 PATENT PENDING BREVET EN INSTANCE US TOCSASTO Liste? LISTE E IL C0 1 Ttertek _ MROANSIU InterteK STANDARD FCC ID:2AI7B-Q26A This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions

(1) This device may not cause harmful inter Supplied by listed LPS or Class 2 power supply with output OC 5V, 2A. Fourni par LPS repertori ou alimentation de classe 2 avec sortie DC 5V, 2A.

[Ottlite Technologies Inc.]

Attention: Certification reviewer RE:

Request for Confidentiality FCC ID: 2AI7B-Q26A To Whom It May Concern:

Permanent Confidentiality [Complete this section if permanent confidentiality is requested]

Request to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:

[Select one or more of items below, as appropriate]

Schematics Block Diagrams Operational Description Tune-up Procedure Parts List Internal Photos (see note) Users Manual (see note) Note 1: Internal Photos may be held confidential 1) if the circuit board or internal components are not accessible to users. For example, it is acceptable if the circuit board is enclosed in epoxy. 2) Also, it is acceptable if the device is not accessible to the public, for example, a device mounted on the top of a large tower (or in a fenced enclosure) such that it is only serviceable by professional designated technicians under a Non-Disclosure Agreement (NDA). All sales for these devices must be under a NDA restricting the disclosure of the propriety information, including internal photos. Users Manual may be held confidential only when the manual contains proprietary technical information intended for professional technicians obligated under a NDA. All sales and distribution of the users manual must be under a NDA that restricts the disclosure of the information. In the application cover letter requesting permanent confidentiality the following additional description and the NDA exhibit is required:

1. Describe in detail how internal photos and/or users manual information are controlled to prevent them from becoming public or disclosed to unauthorized persons. 2. Describe how public access is restricted for products serviceable by professional designated technicians. 3. A statement that all sales of the non-consumer device will be under a NDA to include third party sales and that the final user of the device is subject to the NDA. 4. Provide an example of the NDA between the grantee and a purchaser. The request for confidentiality must Note 2: For scanning receiver, the schematics, block diagrams, operational description, tune-up procedure, parts list and internal photos are always held permanently confidential. Short-term Confidentiality [Complete this section if short-term confidentiality is requested]

Request to withhold from public review for a period of [please enter 1 to 180] days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept short-term confidential for a period above from the date of the grant

[Select one or more of items below that are not selected in the list above, as appropriate]

Schematics Block diagrams Operational Description Tune-up Procedure 1(2) Parts List Test Setup Photos External Photos Internal Photos Users Manual Rationale for request for confidentiality:

We have invested considerable time and materials in research and development to produce the referenced product. Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. Short-term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development. If you have questions or need further information, please contact the undersigned. Sincerely, _________________

[Kyle Albinus]

[Quality Manager]

[2022-02-18]

2(2)

February 14, 2021 Federal Communications Commission 445 12th Street SW Washington, DC 20554 Subject:

Limited Agency Agreement Ottlite Technologies, Inc. FCC ID: 2AI7B-Q26A To Whom It May Concern:

We, Ottlite Technologies, Inc., hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number (2AI7B-Q26A) under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is 14-Feb-2022. The Limited Agency Agreement expires on 14-Feb-2023, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Kyle Albinus Quality Manager OttLite Technologies, Inc. 1715 N. Westshore Blvd. Suite 950 | Tampa, Florida 33607 | Toll Free 800.842.8848 | Local 813.621.0058 | OttLite.com