FCC ID: 2ABGLSW78019 Sch Wireless Bike Computer

19 Assembly 1.Attach the bracket to the handlebar. Make sure that the rubber spacer is between the bracket and handlebar and that the snap buckle is facing the saddle. Speed Clear Hold K2 for 3s until MAX, AVG, MPH/KMPH flash. 4 3 2 2.Run the cable down to the front fork and secure it using a cable tie. 3. Attach the sensor to the front fork and make sure that it is parallel to the spokes. Notice: Dont completely tighten the cable ties straight away. You might need to adjust the sensor angle a little after the magnet has been fitted. 4. Attached the magnet to one of the spokes. 5. Adjust the magnet and the sensor so that they face each other, 2~5mm. 6. Twist the computer to right until it completely into the bracket. Please read the entire instruction manual before using the product and save it for future reference. We reserve the right for any errors in text or images and any necessary changes made to technical data. If you have any questions regarding technical problems, please contact our Customer Services. Product Description Features

- Clock ( 12/24 Hour)

- Current speed (0~ 150 km/h or 93.2 m/h )

- Average speed (0~ 150 km/h or 93.2 m/h )

- Max. speed (0~ 150 km/h or 93.2 m/h )

- Speed tendency: accelerating or decelerating

- Riding distance / DST ( 0~ 9999.9 km or miles )

- Total riding distance/ ODO (odometer)

- Riding timer/ RTM ( up to 99:59:99 hours)

- Total riding time/ TTM ( up to 9999 hours)

- Approximate calorie burn

- Backlight Contents 1. Computer 2. Headlebar bracket with cable, sensor and rubber base. 3. Magnet 4. Battery (2 * Cr2032 , 3V ) 5. 4 cable ties 1 2 4 5 3 X 4 Computer setup 1 K1 1. Shows Clock, Riding time, Total riding time, Riding distance,Total riding distance, Calorie burned, press K1 for data review. K2 2. Shows current speed. 3. appears if speed is above average speed, appears if speed is below average speed. 4. Shows when you start riding, disappears when you stop riding. 5. Setting: Hold both K1 and K2 buttons for 2~3s, you can set up time,wheel size, imperial/metric system, previous total riding distance,riding time. Press K1 move to next figure, K2 increase the figures. Please refer to the below chat flows. Data Clear Hold K1 and K2 for 3s until the screen display reset Notice: each mode data can only be clear separately. Resetting the computer The computer resets to factory setting if:

-The battery be removed

-Hold both K1 and K2 for 2~3s, resetting. Power Saving Mode If the computer is not used or receives no signals for 5 minutes,it will automatically enter power saving mode, the screen will only show current time. Press any button to turn the computer back on again. Sleepping Mode

- If the computer is not used or receives no signal for 7 days,it will automatically enter Sleep mode. The screen will only show Sleep. Press any button to turn the computer back on again.

- Hold both K1 and K2 buttons for 6s, it will enter the sleep mode,Press any button to turn the computer back on again. Other Functions:

-3s EL backlight function by pressing K2 button. Press both K1 and K2 the backlight will keep on.

-The computer low battery warming: When the Cr2032 coin battery voltage is below 2.5 V the will be displayed. A brand new coin battery should be replaced. Wheel size input:

Wheel size diameter Circumference of wheel(mm) 1596 20 1759 22 24 1916 26(650A) 2073 2117 26.5(Tubular) 2124 26.8(700*25C) 2136 26.8(700*28C) 27( 700*32C) 2155 2237 28 (700B) Wheel size diameter Circumference if wheel(mm) ATB 24*1.75 1888 1995 ATB 26*1.4 ATB 26*1.5 2030 ATB 26*1.75 2045 ATB 26*2(650B) 2099 27*1 2136 27*1 1/4 2155 Battery Installation Insert the battery into the computer and sensor, making sure that the + is facing upwards. 4 This device complies with Part 15 o f the F CC Rules. Operat ion is subject to the f ollowing t wo condit ions:

(1) This device may not cause harmf ul int erf erence , and

(2) This device must accept any int erf erence rec eiv ed, inc luding int erf erence that may cause undesired operat ion. Attention that changes or modification not expressly approv the users authority to oper ate the equipment. ed by the party responsible for compliance could void Note: This product has been tested and found to comply with the lim its for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harm ful interference in a residential installation. This product generates , us es , and can radiate radio frequency energy and , if not ins talled and used in accordance with the instruc tions , may cause harmful interference to r adio communications. However , there is no guarantee that interference will not occur in a partic ular installation. If this product does cause harm ful interference to radio or tele vision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different fr om that to which the receiver is connec ted. Consult the dealer or an experienced radio/TV technician for help. Please take attention that changes or modification not expressly approved by the party respons ible for compliance could void the users authority to operate the equipment. This equipment complies with FCC/IC RSS-102 radiation exposure limits for an uncontr olled environment.

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 1 of 3 Internal Photos Pacific Cycle, Inc. 4902 Hammersley Road Madision, WI 53711 USA Applicant:

Address of Applicant:

Equipment Under Test (EUT):

Product Name:

Model No.:

Sch Wireless Bike Computer SW78019-6 Page 1 of 3 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 2 of 3 Page 2 of 3 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 3 of 3 End Page 3 of 3

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 1 of 4 External Photos Pacific Cycle 4902 Hammersley Road Madision, WI 53711 USA Applicant:

Address of Applicant:

Equipment Under Test (EUT):

Product Name:

Model No.:

Sch Wireless Bike Computer SW78019-6 Page 1 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 2 of 4 Page 2 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 3 of 4 Page 3 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 4 of 4 End Page 4 of 4

2imm 22mm FCC ID: 2ABGLSW78019 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including terference that may cause undesired operation.

Signature: hoe pp AC Pacific Cycle Inc. SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States Company Name: Pacific Cycle Inc. Address: 4902 Hammersley Road City, State, zip: Madison, Wisconsin, 53711, United States Regarding: Confidentiality Request regarding application for FCC ID: 2ABGLSW/78019 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission's rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. sincerely, Printed Name (on file with the FCC associated with the Grantee Code). Ryan Shiroma Title: Senior Quality Manager Company Name, Pacific Cycle Inc.

Pacific Cycle Inc. Date: 6/24/2019 TO Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding FCC ID: 2ABGLSW78019 To whom it may concern:

We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Pacific Cycle Inc. This authorization is valid until further written notice from the applicant. Name (Printed):Ryan Shiroma Title: Sr. Quality Manager Signature:

On behalf of | mpany: Pacific Cycle Telephone: 608.268.8313