FCC ID: 2AUD3-SG334G Smart Gate, SG334GA

Smart Gate SG334GA INTRODUCTION SG334GA is a new long-range RFID reader featuring compact dimension, This innovative integrated reader is an all-in-one device that operates at a frequency range of 902-928 MHz and is an ideal solution for applications such as intelligent parking management and access control. It includes a web interfaces that makes it easy to config and use. Additionally, the range of RF power is 10 to 26 dBm which is adjustable remotely. Technical Specifications Operating Frequency 902-928 MHz RF Power Output 10 to 26 dBm (adjustable via the web) Read/Write Distance Up to 7 meter (23 feet) (tags dependent) I/O Interface Power Supply 1 relay output DC 12V / 1A Antenna Dimension 500 mm 200 mm 26 mm Applications Parking lot management. Vehicle access control Automatic weighing.

----------------------------------------------------------------------------------------------------------------------

PAL Electronics Systems, HaTa'asiya 25 st, Ra'anana, Israel 4365413,POB 2516 Tel:972-73-7297808, Website: www.pal-es.com, Email: info@pal-es.com. RFID Smart Gate Controller Installation Instructions Each vehicle has unique RFID Identification sticker with a unique serial number. Placing the sticker at the vehicle windshield should be on the same side as the antenna location at the site. The sticker ID can be received by RFID device up to 7 meters (23 feet) from the antenna base and depends on the environment. Height of the antenna should be about 1.5m to 2.5m from its base. The antenna is transmitting via cone of approximately 30 degrees. 30 1.5-2.5m 3-7 m Highlights Power supply should be 12V DC / 1A To improve the identification transmission it is desirable that the antenna and sticker at the vehicle will be parallel as possible. Placing the sticker at the vehicle windshield should be on the same side as the antenna location at the site. Maximum output relay load 60V/0.9A FCC ID: 2AUD3-SG334G This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures:

Re-orient or re-locate the receiving antenna. Increase the distance between the device and the receiver. Connect the device to an outlet on a circuit different from the one that supplies power to the receiver. Consult the dealer or an experienced radio/TV technician. WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with FCC Rules Part 15: Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation. To comply with FCC Section 1.1310 for human exposure to radio frequency electromagnetic fields, implement the following instruction:

A distance of at least 20 cm. between the Antenna and all persons should be maintained during the operation of the equipment.

----------------------------------------------------------------------------------------------------------------------

PAL Electronics Systems, HaTa'asiya 25 st, Ra'anana, Israel 4365413,POB 2516 Tel:972-73-7297808, Website: www.pal-es.com, Email: info@pal-es.com.

SN: RD300100265 CODE: 12345 MODEL: SG334GA FCC ID: 2AUD3-SG334G CONTAINS FCC ID: RI7LE910NAV2 www.pal-es.com

Date: September 2, 2019 To: Timco Engineering Inc. To Whom It May Concern We hereby authorize Mr. Ilan Cohen of I.T.L. (Product Testing) Ltd (ITL) to sign FORM 731 on our behalf for the following FCC ID application:

FCC ID: 2AUD3-SG334G Thank you, Arie Litbak, Owner

Date: September 2, 2019 To Whom It May Concern We hereby authorize Mr. Ilan Cohen of I.T.L. (Product Testing) Ltd (ITL) to act on our behalf regarding the FCC Certification Process for the following application:

FCC ID: 2AUD3-SG334G Thank you, Arie Litbak, Owner

Date: September 2, 2019 Federal Communications Commission Authorization and Evaluation Division To: Federal Communications Commission Confidentiality Request regarding application for the FCC certification of FCC ID: 2AUD3-SG334G Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

a. CONF APPENDIX SG334GA Partlst.pdf b. CONF APPENDIX SG334GA BlkDia.pdf c. CONF APPENDIX SG334GA Schem.pdf d. CONF APPENDIX SG334GA OpDes.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Thank you, Arie Litbak, Owner

Date: September 2, 2019 Attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

The Pal electronics systems, model SG334GA, FCC ID: 2AUD3-SG334G, and label are so small that it cannot include the statement specified in FCC Part 15 Sub-part A, Section 15.19

(a) (3) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)

(2) This device may not cause harmful interference and This device must accept any interference received, including interference that may cause undesired operation."

Due to this reason, we are using the provisions of Part 15 Sub-part A, Section 15.19 (a) (5) and this statement appears in a prominent location in the user manual. Please contact me if there is any information you may need. Thank you, Arie Litbak, Owner