microUCS User Manual Hardware Version:V1.2 Guide Version: V1.0 Copyright Copyright 2012 PaloSanto Solutions Inc. All rights reserved. No part of this document may be reproduced without prior written permission. Confidentiality Information contained herein is of a highly sensitive nature and is confidential and proprietary to PaloSanto Solutions Inc. No part may be distributed, reproduced or disclosed orally or in written form to any party other than the direct recipients without the express written consent of PaloSanto Solutions Inc. Disclaimer PaloSanto Solutions Inc. reserves the right to modify the design, characteristics, and products at any time without notification or obligation and shall not be held liable for any error or damage of any kind resulting from the use of this document. PaloSanto Solutions has made every effort to ensure that the information contained in this document is accurate and complete; however, the contents of this document are subject to revision without notice. Please contact PaloSanto Solutions to ensure you have the latest version of this document. Trademarks All other trademarks mentioned in this document are the property of their respective owners. 1 Compliance information EMI and EMS For FCC, MICROUCS has been tested as a CPU board, installed in an enclosure, with the top cover removed. No further testing should be required if the board is used with other FCC tested modular components. Please see http://www.fcc.gov/oet/ for more details. Testing for CE mark must be done at the level of the complete product. Please contact PaloSanto Solutions for assistance and documentation. It can be used as an I.T.E, as well as a generic device. For an I.T.E, it must be tested according to EN55022 and EN55024; for a generic device, it is suit for EN 61000-6-2 (EMI test for commercial and light industrial environment) and EN61000-6-3 (Immuty test for Industrial environment). ESD For satisfactory resistance to electrostatic discharge events (ESD), the case of the MICROUCS board should be grounded earth Ground termintal. (eg. through the mounting holes, or the serial port connector). Under this condition, the system can be get class B evaluation according to EN 61000-4-2. Recycling / disposal Do not discard electronic products in household trash!
All waste electronics equipment should be recycled according to local regulations. Information for the recycler Please cut off Lithium battery, if present, for separate recycling. PaloSanto Solutions enclosures are made of aluminum. 2 Chapter 1 Overview The microUCS is the ideal IP PBX for small business or for your home, allowing you to monitor your communications in a very small but also powerful device that comes pre-installed with Elastix. A micro computer with a powerful solution, The compact design of microUCS together with Elastix as a unified communications solution, makes it a powerful IP PBX that allows you to monitor communications in your office or home from anywhere. Easy to install, powerful administration as only Elastix offers and its very low power consumption, make it a very safe and cost effective solution. Features Dial
-By-Name Directory Auto Attendants
Voicemail
Music on Hold Multiple Languages Ring Groups Call Queue Call Waiting Caller Display Conference Call Call Hold/Transfer Call Park Call Pickup Automatic Fax Detection Remote Management Remote Exte nsions Specification
CPU: TI AM1808B 456MHZ
DRAM: 2 GB DDR2 SDRAM
Storage: 1 SD Socket
Network interface: 10/100Mbps
Operating System: Elastix 32 bitx
PBX size: (28.3mm x 165 mm x95.8mm) I/O: 1*DB9 serial port, 1*USB 2.0 port 3
Temperature: 0C to 60C
PCB layer: 6
Voltage range :12V DC supply through DC jack
Power dissipation: ~1.5W (Minimum Power Dissipation) Chapter 2 microUCS Connector and Jumper 1. Layout 2. Connector and Jumper List Name J1 J12 J13 J2 J4 Function Main Power in Jacket Serial Port (RS232) Ethernet Port USB Port SD Card interface 3. System Status Indicator 4 Name D3 Function System status indicator 4. Connector and Jumper Description J1 Main Power Jacket DC in @12V 1 Pin 1 2 J13 100Mbps Ethernet Port 2 Pin 1 2 3 4 5 6 7 8 Name Gnd Vin Name TD+
TD-
RD+
RD-
J2 USB Port 1 USB2.0 ports. 500 mA Continuous Current per Channel. Short-Circuit and Thermal Protection with Overcurrent Logic. 5 Pin 1 2 Name 5v Data-
Pin 3 4 Name Data+
Ground J12 Serial Port (rs232) Pin 1 2 3 4 5 6 7 8 9 Name
RXD TXD
GND
6 FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.