SP-1000 Quick Start Guide TOP VIEW BOTTOM VIEW K R O W T E N R E W O P K R O W T E N R E W O P RESET / RESTORE RESET / RESTORE POWER STATUS INDICATOR LIGHTS POWER ON/OFF AND NETWORK CONNECTION STATUS INDICATOR BOTTOM OUTLET GROUND PIN RECEPTACLE FACING WALL OUTLET INSTALLATION 1. Turn OFF the equipment that you are plug-
ging into the SP-1000. 2. Plug SP-1000 into the wall outlet. Press the POWER /NETWOK button. The blue POWER light indicates power is on. I E E B G Z
. T E N 3. Plug your equipment into the AC outlets. 4. If the NETWORK light is GREEN, the SP-
1000 is connected to a ZigBee network. If the NETWORK light is RED, the MD2-ZB is not connected to a ZigBee network. Proceed to step 6, SETUP SETUP 5. Verify that a BlueBOLT ZigBee, ZigBee-
Ethernet Bridge device is powered on and within 100 ft. of an active ZigBee device. 6. Through the BlueBOLT interface, enable NETWORK JOINING. Refer to the user manual for BB-ZIGBEE for detailed instructions. B 7. To indicate that the unit has not joined the network, the NETWORK LED is OFF. 8. To initiate device discovery, The NETWORK button is presseed for 5 seconds. While the unit is attempting to join the ZigBee HA network, The NETWORK LED is illuminated YELLOW. 9. After the unit has succesfully joined the ZIG-
Bee HA network, the NETWORK LED is GREEN. If unit fails to join the network after 10 seconds, repeat steps 5 through 9. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications of Part 15 of FCC rules. These specifications are designed to provide reasonable protection against such interference win a residential installation. However, there is no guarantee that interference will not occur in a particular installation. In accordance with FCC 15.21, changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. RESET / RESTORE K R O W T E N SP-1000 SP-1000 SP-1000 I E E B G Z
. T E N Multible SP-1000 units can be installed within 100 ft. from an active ZigBee device (BB-ZIGBEE BRIDGE or MD2-ZB). OUTDOOR USE IS PROHIBITED!
www.panamax.com www.mybluebolt.com www.furmansound.com Troubleshooting Your BlueBOLT enabled Power Management Component (BB-ZigBee) is completely plug-
and-play and does not require any software installation. The BlueBOLT control interface is operated through your web browser. 1) Using any Internet connected computer, go to www.mybluebolt.com using your standard Internet browser. 2) Follow the on screen instructions to create an account and/or take control of your BlueBOLT enabled product. Note: you will need the BB-ZigBees unique MAC address and challenge key (provided on the label on the back of BB-ZigBee) in order to register the unit online. 3) If BlueBOLT cannot detect your device within 20 seconds of inputting your MAC address and challenge key, please follow the on-screen troubleshooting guide. Also confirm the BB-ZigBee is properly connected to the Internet. Is your BB-ZigBee receiving power? Check the power cable and confirm the unit is on. Is your BB-ZigBee installed properly? The Link light should be illuminated (solid green) and the Activity light should be blinking intermittently
(green). Is your Internet connection functioning?
Can you access a general web page?
Is your BB-ZigBee connected to your internet router or modem? Check the Ethernet cable and confirm that the unit is connected to an active Internet connection, and make sure those connected devices are receiving power. If you have answered Yes to all of these questions and are still unable to connect your Power Management component, (BB-ZigBee) contact Panamax/Furman customer service at 1-800-472-5555. SERVICE If you require technical support or equipment service, please contact the Service Department at 1-800-472-5555. All equipment being returned for repair must have a Return Authorization (RA) number. To get an RA number, call the Customer Service Department. Before returning any equip-
ment for repair, be sure that it is adequately packed and cushioned against damage in ship-
ment, and that it is insured. We suggest that you save the original packaging and use it to ship the product for servicing. Also, please provide a note with your name, address, phone number, RA number and a description of the problem. LIMITED 1 YEAR WARRANTY Panamax/Furman Limited Product Warranty:
Panamax Inc. warrants to the purchaser of this product for a period of one (1) year from the date of purchase, that the unit shall be free of defects in design, material or workmanship, and Panamax Inc. will repair or replace any defective unit. Full warranty information is available online at www.Panamax.com or www.FurmanSound.com. FCC CLASS B DIGITAL DEVICE INFORMATION NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Panamax LLC, 1690 Corporate Circle, Petaluma, CA 94954 707-283-5900 800-472-5555 www.panamax.com www.mybluebolt.com 2012 Panamax LLC, Panamax, Furman and BlueBOLT logos are US registered trademarks of Panamax www.panamax.com www.mybluebolt.com www.furmansound.com