FCC ID: 2AM4X-ENY-T3U01W ENY Button

ENY Users Manual Business Development Center Industrial Solutions Company Panasonic Corporation Panasonic Corporation

[0]

About This Manual This document is the users manual for ENY system, which consists of the ENY button (RF transmitter) and ENY receiver (the RF receiver). The following items are described in the document.

- System configuration

- How to operate

- Communication Interface This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, Including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). Panasonic Corporation

[1]

Product Discription The ENY system is a system that collects the customers experience of service satisfaction and customer opinions, and feeds the results back to the store manager. Press the ENY button in response to the questions presented and your opinion will be sent wirelessly. ENY receiver sends the received data to the cloud and aggregate it in the cloud. Question Board ENY button Panasonic Corporation via USB OR 925MHz ENY receiver G Cloud Gateway Figure 1

[2]

System Configuration The configuration of ENY system is shown in Figure 1. Pressing the ENY button generates electricity and become active for a while ( less than 45[ms] ). During the active time the button can transmit RF signal. The ENY receiver should be plugged into the gateway via USB and recognized as Virtual COM port. The receiver can communicate with the ENY button while the button is active. The operation is done in Sub-GHz (925MHz) and the protocol is ENY original. ENY button does not need the power supply, and ENY receiver requires 5V via USB. The ID of the connected ENY button will be output on the terminal software (Putty, Teraterm etc.). The application should be implemented in the gateway to be triggered by the signal from ENY button. 925MHz ENY button ENY receiver via USB OR Gateway Panasonic Corporation Figure 1

[3]

Sequence Between Button And Receiver The sequence between ENY button and ENY receiver is shown in Figure 2. The button makes three times of ID transmission at a maximum. By changing the second and third retransmission timings, wireless communication collisions are avoided and communication reliability is improved. ENY button ENY receiver Press button 1st 2nd 3rd Send ID in Freq1 (seq=0) waitX[ms]

Send ID in Freq1 (seq=1) waitY[ms]

Send ID in Freq1 (seq=2) Figure 2

[4]

Panasonic Corporation Communication I/F In Host Computer Command I/F between ENY receiver and the PC is shown in Figure 3. Command:

Command Description get_id ver Shows the RX ID. Shows the FW version.

Parameter Response Note

[RX_ID]

<Eny Version: 10.00.00>

Figure 3 Note:

- Receiver outputs the button information in ASCII text via USB when it receives the signal successfully. e.g. [Button ID] [Sequence No.] [Cumulated No.] [Channel No.] [RSSI]

Panasonic Corporation

[5]

Communication I/F In Host Computer Serial port settings :

Speed Data bits Stop bits Parity Flow control

[bps]

[bits]

[bit]

:115200

:8

:1

:None

:None Setting example (PuTTY):

Panasonic Corporation Figure 4

[6]

Communication I/F In Host Computer Command execution examples :

Get ID command ver command Panasonic Corporation Figure 5

[7]

LED Status On ENY receiver LED status on ENY receiver is shown in Figure 6. 1. Blue LED : Blinks when it receives ID information successfully LED OFF LED Blink

- BLUE-

2. Green LED : Become ON when the power is supplied LED LED OFF LED ON

-GREEN-

ENY receiver 3. Red LED : Become ON when the internal error detected LED OFF Panasonic Corporation LED ON

-RED-

Figure 6

[8]

Disclaimer Please note that the information or the program it in this document may be changed or updated without notice. For any damages caused by these changes and updates, we are not responsible. Panasonic Corporation

[9]

Panasonic Corporation FCC ID Label FCC ID.: 2AM4X-ENY-T3U01W 1006 Kadoma, Kadoma City, Osaka 571-8506, Japan TEL: 815034878129

Panasonic Corporation The FCC ID will be placed on the equipment as shown in the photograph below. FCC ID.: 2AM4X-ENY-T3U01W 1006 Kadoma, Kadoma City, Osaka 571-8506, Japan TEL: 815034878129

Panasonic 2019/11/11 Federal Communications Commission Authorization and Evaluation Division ATTESTATION FCC ID: 2AM4X-ENY-T3U01W Product: ENY Button Model: ENY-T3U01W We dont provide any controls or software to allow operation outside the USA frequency band when we sell a product bearing the FCC ID: 2AM4X-ENY-T3U01W anywhere in the world. Sincerely, Masaaki Noda /

Panasonic Corporation Tel: 815034878129 Fax: N/A Email: noda.masaaki@jp.panasonic.com

Panasonic FCC ID.: 2AM4X-ENY-T3U01W Date: November 11, 2019 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below:

Type of Confidentiality Requested Exhibit

&) Permanent Block Diagrams L] Short Term External Photos LC) Short Term Internal Photos

& Permanent Operation Description/Theory of Operation

() Permanent Parts List & Placement/BOM Permanent Tune-Up Procedure

&} Permanent Schematics O) Short Term Test Setup Photos OC) Short Term Users Manual The above materials contain trade secrets and proprietary information not customarily Released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Sincerely, th a uh adfp Name: Masaaki Noda Title:

Company name: Panasonic Corporation

Panasonic Declaration of Authorization We Name: Panasonic Corporation Address: 1006 Kadoma, Kadoma City, Osaka 571-8506, Japan City: Osaka Country: Japan Declare that:

Name Representative of agent: Vincent Lin Agent Company name: DEKRA Testing and Certification Co., Ltd. Address: No.5-22, Ruishukeng, Linkou Dist., City: New Taipei City 24451, Country: Taiwan, R.O.C. is authorized to apply for Certification of the following product(s):

Product Name: ENY Button Model: ENY-T3U01W FCC ID: 2AM4X-ENY-T3U01W Trademark: Panasonic on our behaif. This is valid until November 11, 2020, or until FCC certification are completed, whichever comes sooner. Date: November 11, 2019 City: Osaka Name: Masaaki Noda Function:

Signature: / frosawe Av (ig