| all | frequencies |
|
|
exhibits | applications |
|---|---|---|---|---|---|
| manuals | |||||
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
Test Report | Users Manual | 1.31 MiB | / September 08 2014 | |||
| 1 |
|
User Manual | Users Manual | 369.69 KiB | / September 08 2014 | |||
| 1 | Cover Letter(s) | |||||||
| 1 | Attestation Statements | |||||||
| 1 | Cover Letter(s) | |||||||
| 1 | Cover Letter(s) | |||||||
| 1 | External Photos | / September 08 2014 | ||||||
| 1 | Internal Photos | / September 08 2014 | ||||||
| 1 | ID Label/Location Info | |||||||
| 1 | RF Exposure Info | |||||||
| 1 | Test Setup Photos | / September 08 2014 | ||||||
| 1 | Test Report |
| 1 | Test Report | Users Manual | 1.31 MiB | / September 08 2014 |
Report No. 258223-5 Test Report Product UPCS Transceiver in Outdoor Camera Name and address of the applicant Panasonic Corporation of North America Name and address of the manufacturer Panasonic System Networks Co., Ltd. 1-62, 4-chome, Minoshima, Hakata-ku Fukuoka 812-8531, Japan Model Rating KX-HNC600 120 V AC (Mains) Trademark Panasonic Serial number
/
Additional information DECT 6.0 Tested according to FCC Part 15, subpart D Isochronous UPCS Device, 1920 1930 MHz Industry Canada RSS 213, Issue 2 2 GHz License-exempt Personal Communications Service Devices (LE-PCS) Order number 258223 Tested in period 2014.05.07 to 2014.05.14 Issue date Name and address of the testing laboratory 2014.05.26 FCC No: 994405 IC OATS: 2040D-1 TEL: (+47) 22 96 03 30 FAX: (+47) 22 96 05 50 Instituttveien 6 Kjeller, Norway Prepared by [Frode Sveinsen]
Approved by [G.Suhanthakumar]
This report shall not be reproduced except in full without the written approval of Nemko. Opinions and interpretations expressed within this report are not part of the current accreditation. This report was originally distributed electronically with digital signatures. For more information contact Nemko. Nemko Norway Nemko AS, Instituttveien 6, P.O. Box 96 Kjeller, 2007 Kjeller, Norway TEL +47 22 96 03 30 FAX +47 22 96 05 50 EMAIL info@nemko.com ENTERPRISE NUMBER NO974404532 Template version: B nemko.com/no CONTENTS TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 INFORMATION ................................................................................................................................. 3 1 Tested Item........................................................................................................................................ 3 1.1 Description of Tested Device ............................................................................................................. 3 1.2 Exposure Evaluation .......................................................................................................................... 3 1.3 Test Environment .............................................................................................................................. 4 1.4 Test Engineer(s) ................................................................................................................................ 4 1.5 1.6 Test Equipment ................................................................................................................................. 4 1.7 Other Comments ............................................................................................................................... 4 2 TEST REPORT SUMMARY .............................................................................................................. 5 2.1 General .............................................................................................................................................. 5 Test Summary ................................................................................................................................... 6 2.2 TEST RESULTS ................................................................................................................................ 7 3 Power Line Conducted Emissions ..................................................................................................... 7 3.1 Coordination with fixed microwave .................................................................................................. 10 3.2 Digital Modulation Techniques ........................................................................................................ 10 3.3 Labeling Requirements ................................................................................................................... 10 3.4 Antenna Requirement...................................................................................................................... 11 3.5 Channel Frequencies ...................................................................................................................... 11 3.6 Automatic Discontinuation of Transmission .................................................................................... 12 3.7 Peak Power Output ......................................................................................................................... 13 3.8 3.9 Emission Bandwidth B ..................................................................................................................... 16 3.10 Power Spectral Density ................................................................................................................... 19 3.11 In-Band Unwanted Emissions, Conducted ...................................................................................... 22 3.12 Out-of-band Emissions, Conducted................................................................................................. 24 3.13 Carrier Frequency Stability .............................................................................................................. 30 3.14 Frame Repetition Stability ............................................................................................................... 31 3.15 Frame Period and Jitter ................................................................................................................... 31 3.16 Monitoring Threshold, Least Interfered Channel ............................................................................. 33 3.17 Threshold Monitoring Bandwidth ..................................................................................................... 35 3.18 Reaction Time and Monitoring Interval ............................................................................................ 36 3.19 Time and Spectrum Window Access Procedure ............................................................................. 38 3.20 Acknowledgements and Transmission Duration ............................................................................. 39 3.21 Dual Access Criteria Check ............................................................................................................. 41 3.22 Alternative Monitoring Interval ......................................................................................................... 45 TEST SETUPS ................................................................................................................................ 46 4 Frequency Measurements ............................................................................................................... 46 4.1 Timing Measurements ..................................................................................................................... 46 4.2 Conducted Emission Test................................................................................................................ 46 4.3 4.4 Power Line Conducted Emissions Test ........................................................................................... 46 4.5 Monitoring Tests .............................................................................................................................. 47 5 TEST EQUIPMENT USED .............................................................................................................. 48 Nemko Norway, Instituttveien 6, Kjeller, Norway Page 2 (48) 1 INFORMATION 1.1 Tested Item Name :
Model name :
FCC ID :
Industry Canada ID :
Serial number :
Hardware identity and/or version:
Software identity and/or version :
Tested to IC Radio Standard (RSS) :
Test Site IC Reg. Number :
Frequency Range :
Number of Channels :
Type of Modulation :
Conducted Output Power :
Antenna Connector :
Number of Antennas :
Antenna Diversity Supported :
Power Supply :
TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Panasonic KX-HNC600 ACJ96NKX-HNC600 216A-KXHNC600
/
PNLB2371xx SW401 RSS-213 Issue 2, RSS-GEN Issue 3 IC 2040D-1 1921.536 1928.448 MHz 5 RF Channels, 5x12 = 60 TDMA Duplex Channels Digital (Gaussian Frequency Shift Keying) 62 mW (Peak) None 1 No AC Adaptor Model: PNLV236 1.2 Description of Tested Device The EUT is an Indoor Camera with DECT Transmitter and is an initiating device as described in ANSI C63.17 and is designed to operate together with a DECT fixed part (i.e. a base station), which is the responding device. 1.3 Exposure Evaluation The EUT is a fixed device and the user manual contains a statement that it should be installed at least 20cm away from any persons. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 3 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 1.4 Test Environment Temperature:
Relative humidity:
20.7 21.8 C 36 - 43 %
Normal test voltage:
120 V AC (with AC Adaptor PNLV236) The values are the limit registered during the test period. 1.5 Test Engineer(s) Frode Sveinsen Thanh Tran 1.6 Test Equipment See list of test equipment in clause 6. 1.7 Other Comments The Monitoring and Time and Spectrum Window Access tests were performed with Test Set-Up 6 (Ref. clause 5). A clock signal from the companion device was used to synchronize the Pulse Pattern Generator and the Spectrum Analyzer to the start of the DECT time window. The EUT was limited by administrative commands to operate on only two frequency carriers. For the tests where the EUT was required to operate on only one frequency carrier, one carrier was blocked by applying a CW interfering signal from RF Generator 3. The Pulse Pattern Generator was used to apply time synchronized interference to time windows where this was required. This EUT supports Least Interfered Channel procedure (LIC), the Monitoring and Time and Spectrum Window Access tests were conducted as specified for EUTs that support LIC procedure. All tests except Power-Line Conducted Emissions were performed in conducted mode with a temporary antenna connector. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 4 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 2 TEST REPORT SUMMARY 2.1 General All measurements are traceable to national standards. The tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with FCC CFR47 Part 15D for Isochronous UPCS Devices and Industry Canada RSS-213 Issue 2 / RSS-GEN Issue 3. All tests were conducted is accordance with ANSI C63.4-2009 and ANSI C63.17-2006. Antenna Gain tests were made in a 3m fully-anechoic chamber. A description of the test facility is on file with the FCC and Industry Canada. New Submission Class II Permissive Change PUB Equipment Code Production Unit Pre-production Unit Family Listing THIS TEST REPORT APPLIES ONLY TO THE ITEM(S) AND CONFIGURATIONS TESTED. Deviations from, additions to, or exclusions from the test specifications are described in Summary of Test Data. Nemko Group authorizes the above named company to reproduce this report provided it is reproduced in its entirety and for use by the companys employees only. Any reproduction of parts of this report requires approval in writing from Nemko Group. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Group accepts no responsibility for damages suffered by any third party as a result of decisions made or actions based on this report. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 5 (48) 2.2 Test Summary Name of test Power Line Conducted Emission Coordination with fixed microwave Digital Modulation Techniques Labeling requirements Antenna Requirement Channel Frequencies Automatic discontinuation of transmission Emission Bandwidth In-band emissions Out-of-band emissions Output Power and Antenna Gain Power Spectral Density Carrier frequency stability Frame repetition stability Frame period and jitter Monitoring threshold, Least interfered channel Monitoring of intended transmit window and maximum reaction time Threshold monitoring bandwidth Reaction time and monitoring interval Access criteria test interval Access Criteria functional test Acknowledgements Transmission duration Dual access criteria Alterative monitoring interval Spurious Emissions (Radiated) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 FCC CFR 47 Paragraph #
15.107(a) 15.207(a) 15.307(b) 15.319(b) 15.19(a)(3) 15.317, 15.203 15.303 15.319(f) 15.323(a) 15.323(d) 15.323(d) 15.319(c)(e), 15.31(e) 15.319(d) 15.323(f) 15.323(e) 15.323(e) 15.323(c)(2);(5); (9) 15.323(c)(1) 15.323(c)(7) 15.323(c)(1);(5); (7) 15.323(c)(4);(6) 15.323(c)(4);(6) 15.323(c)(4) 15.323(c)(3) 15.323(c)(10) 15.323(c)(10);(11) 15.319(g) 15.109(a) 15.209(a) IC RSS-213 Paragraph #
6.3 RSS-GEN 7.2.2 N/A 6.1 3 RSS-GEN 5.2 RSS-GEN 7.1.2 1 4.3.4(a) 6.4 6.7.2 6.7.1 6.5 and 4.1(e) 4.3.2.1 6.2 4.3.4(c) 4.3.4(c) 4.3.4(b) 4.3.4(b) 4.3.4(b) 4.3.4(b) 4.3.4(b) 4.3.4(b) 4.3.4(b) 4.3.4(b) 4.3.4(b) 4.3.4(b) 4.3.3 RSS-GEN 7.2.3 Verdict Complies Complies Complies Complies Complies Complies Complies Complies Complies Complies Complies Complies Complies Complies Complies Complies Complies Complies Complies N/A1 N/A1 Complies Complies Complies N/A2 N/A3 1 Only applies for equipment that transmits unacknowledged control and signaling information 2 The client declares that the tested equipment does not implement this provision 3 Not required if the Conducted Out-of-Band Emissions test is Passed Nemko Norway, Instituttveien 6, Kjeller, Norway Page 6 (48) 3 TEST RESULTS TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 3.1 Power Line Conducted Emissions Para. No.: 15.207 (a) Test Performed By: Thanh Tran Date of Test: 13-May-2014 Measurement procedure:
Test Results:
ANSI C63.4-2009 using 50 m H/50 ohms LISN. Complies Measurement Data:
See attached graph, (Peak detector). Highest measured value (L1 and N):
(Plots show maximum of Phase L1 and N) Nemko Norway, Instituttveien 6, Kjeller, Norway Page 7 (48) Standby Mode with PNLV236 Adaptor, 120V 60Hz:
Frequency
[MHz]
0.395000 0.370000 0.395000 0.445000 0.480000 0.740000 0.760000 0.785000 0.815000 0.840000 0.945000 1.155000 1.180000 1.240000 1.455000 22.325000 Level
[dBuV]
39.00 29.00 36.50 20.20 11.20 22.10 19.40 17.40 19.90 18.90 15.10 17.10 15.00 11.70 13.90 14.30 Af
[dB]
10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.20 11.30 Limit
[dBuV]
58.00 48.50 48.00 47.00 46.30 46.00 46.00 46.00 46.00 46.00 46.00 46.00 46.00 46.00 46.00 50.00 Transmit Mode with PNLV236 Adaptor, 120V 60Hz:
Frequency
[MHz]
0.395000 0.750000 0.170000 0.370000 0.395000 0.570000 0.750000 0.785000 0.830000 0.865000 0.950000 1.695000 1.925000 8.670000 12.200000 18.000000 22.205000 Level
[dBuV]
39.20 30.30 16.00 28.40 36.50 17.30 9.00 18.00 6.90 17.00 12.00 10.70 12.20 15.10 13.00 11.30 15.20 Af
[dB]
10.20 10.20 10.10 10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.20 10.60 10.70 11.00 11.30 Limit
[dBuV]
58.00 56.00 55.00 48.50 48.00 46.00 46.00 46.00 46.00 46.00 46.00 46.00 46.00 50.00 50.00 50.00 50.00 TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Margin Det Position
[dB]
19.00 19.50 11.50 26.80 35.10 23.90 26.60 28.60 26.10 27.10 30.90 28.90 31.00 34.30 32.10 35.70 QP AV AV AV AV AV AV AV AV AV AV AV AV AV AV AV L1 L1 L1 L1 L1 L1 L1 N N N N N N L1 L1 N Margin Det Position
[dB]
18.80 25.70 39.00 20.10 11.50 28.70 37.00 28.00 39.10 29.00 34.00 35.30 33.80 34.90 37.00 38.70 34.80 QP QP AV AV AV AV AV AV AV AV AV AV AV AV AV AV AV L1 N L1 L1 L1 N N N N N N L1 L1 L1 L1 L1 N Verdict
[Pass/Fail]
Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Verdict
[Pass/Fail]
Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Nemko Norway, Instituttveien 6, Kjeller, Norway Page 8 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600
+
+
+
++
+
+
+
+
+
+
+
+
x
+
+
Level [dBV]
80 70 60 50 40 30 20 10 0 150k 300k 500k x
+
MES 258223N_Qp MES 258223N_Av MES 258223N LIM EN 55022 V QP LIM EN 55022 V AV 1M Frequency [Hz]
2M 3M 5M 7M 10M 30M Standby Mode with PNLV236 Adaptor, 120V 60Hz Level [dBV]
80 70 60 50 40 30 20 10
+
x
+
+
x
+
+
+
+
+
+
+ +
+
+
+
+
0 150k 300k 500k x
+
MES 258223N_Qp MES 258223N_Av MES 258223N LIM EN 55022 V QP LIM EN 55022 V AV 1M Frequency [Hz]
2M 3M 5M 7M 10M 30M Transmit Mode with PNLV236 Adaptor, 120V 60Hz Nemko Norway, Instituttveien 6, Kjeller, Norway Page 9 (48) 3.2 Coordination with fixed microwave TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 The affidavit from UTAM, Inc. is included in the documentation supplied by the applicant:
Yes No Requirement, FCC 15.307 (b):
Each application for certification of equipment operating under the provisions of this Subpart must be accompanied by an affidavit from UTAM, Inc. certifying that the applicant is a participating member of UTAM, Inc. In the event a grantee fails to fulfill the obligations attendant to participation in UTAM, Inc., the Commission may invoke administrative sanctions as necessary to preclude continued marketing and installation of devices covered by the grant of certification, including but not limited to revoking certification. 3.3 Digital Modulation Techniques The EUT uses Multi Carrier / Time Division Multiple Access / Time Division Duplex and Digital GFSK modulation. For further details see the operational description provided by the applicant. Requirement, FCC 15.319(b):
All transmissions must use only digital modulation techniques. 3.4 Labeling Requirements See separate documents showing the label design and the placement of the label on the EUT. Requirements FCC 15.19 The FCC Identifier shall be displayed on the label, and the device(s) shall bear the following statement in a conspicuous location on the device or in the user manual if the device is too small:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The label itself shall be of a permanent type, not a paper label, and shall last the lifetime of the equipment. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 10 (48) 3.5 Antenna Requirement TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Does the EUT have detachable antenna(s)?
If detachable, is the antenna connector(s) non-standard?
The tested equipment has only integral antennas. The conducted tests were performed on a sample with a temporary antenna connector. Requirement: FCC 15.203, 15.204, 15.317. Yes Yes No No 3.6 Channel Frequencies UPCS CHANNEL Upper Band Edge 0 (Highest) 1 2 3 4 (Lowest) Lower Band Edge FREQUENCY (MHz) 1930.000 1928.448 1926.720 1924.992 1923.264 1921.536 1920.000 Requirement: FCC 15.303 Within 1920 -1930 MHz band for isochronous devices. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 11 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 3.7 Automatic Discontinuation of Transmission Does the EUT transmit Control and Signaling Information?
YES NO TYPE OF EUT :
INITIATING DEVICE RESPONDING DEVICE The following tests simulate the reaction of the EUT in case of either absence of information to transmit or operational failure after a connection with the companion device is established. Number Test 1 2 3 4 5 6 Power removed from EUT Switch Off EUT Hook-On by EUT Power Removed from Companion Device Switch Off Companion Device Hook-On by Companion Device EUT Reaction Verdict C N/A N/A A N/A N/A Pass Pass Pass Pass Pass Pass A B C N/A - Not Applicable (Neither EUT nor Companion Device have On/Off switch or can perform Hook-On)
- Connection breakdown, Cease of all transmissions
- Connection breakdown, EUT transmits control and signaling information
- Connection breakdown, Companion Device transmits control and signaling information Requirements, FCC 15.319(f) The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude transmission of control and signaling information or use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 12 (48) 3.8 Peak Power Output Test Method:
ANSI C63.17, clause 6.1.2. Test Results: Complies Measurement Data:
Maximum Conducted Output Power Channel No. Frequency
(MHz) 4 2 0 1921.536 1924.992 1928.448 TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Maximum Conducted Output Power
(dBm) 17.6 18.0 17.8 Maximum Antenna Gain
(dBi) 0.0*
0.0*
0.0*
Maximum Radiated Output Power
(dBm) 17.6 18.0 17.8
*Antenna gain value is declared by the manufacturer. Limit:
Conducted: 100 W x SQRT(B) where B is the measured Emission Bandwidth in Hz FCC 15.319(c)(e):
20.76 dBm (119 mW) RSS-213, Issue 2:
20.51 dBm (113 mW) The antenna gain is below 3 dBi, no reduction in transmit power is necessary. Requirements, FCC 15.319(c)(e), RSS-213, Issue 2 Peak transmit power shall not exceed 100 microwatts multiplied by the square root of the emission bandwidth in Hertz. The peak transmit power shall be reduced by the amount in decibels that the maximum directional gain of the antenna exceeds 3 dBi. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 13 (48) Conducted Peak Output Power TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Lower Channel Upper Channel Nemko Norway, Instituttveien 6, Kjeller, Norway Page 14 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Middle Channel Nemko Norway, Instituttveien 6, Kjeller, Norway Page 15 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 3.9 Emission Bandwidth B Test Method:
ANSI C63.17, clause 6.1.3. Test Results: Complies Measurement Data:
Channel No. 4 0 Channel No. 2 Channel No. 4 0 Channel No. 4 0 Frequency
(MHz) 1921.536 1928.448 Frequency
(MHz) 1924.992 Frequency
(MHz) 1921.536 1928.448 Frequency
(MHz) 1921.536 1928.448 26 dB Bandwidth B
(kHz) 1420 1410 99% Bandwidth
(kHz) 1266 6 dB Bandwidth
(kHz) N/A N/A 12 dB Bandwidth
(kHz) N/A N/A Requirements, FCC 15.323(a) The 26 dB Bandwidth B shall be larger than 50 kHz and less than 2.5 MHz. Requirements, RSS-213 Issue 2, clause 6.4 The 99% Bandwidth shall be larger than 50 kHz and less than 2.5 MHz. No requirements for 6 and 12 dB Bandwidth, these values are only used for testing Monitoring Bandwidth if the Simple Compliance test fails (ANSI C63.17, clause 7.4). Nemko Norway, Instituttveien 6, Kjeller, Norway Page 16 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Emission Bandwidth B, Lower Channel Emission Bandwidth B, Upper Channel Nemko Norway, Instituttveien 6, Kjeller, Norway Page 17 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 99% Bandwidth, Middle Channel Nemko Norway, Instituttveien 6, Kjeller, Norway Page 18 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 3.10 Power Spectral Density Test Method:
ANSI C63.17, clause 6.1.5. Test Results: Complies Measurement Data:
Channel No. 4 0 Frequency
(MHz) 1921.536 1928.448 Power Spectral Density
(dBm) 1.1 1.3 Averaged over 1000 sweeps. Requirements, FCC 15.319(d) The Power Spectral Density shall be less than 3 mW (4.77 dBm) when averaged over at least 100 sweeps. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 19 (48) Power Spectral Density Lower Channel:
TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Overview Averaged, 1000 Sweeps Nemko Norway, Instituttveien 6, Kjeller, Norway Page 20 (48) Upper Channel:
TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Overview Averaged, 1000 Sweeps Nemko Norway, Instituttveien 6, Kjeller, Norway Page 21 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 3.11 In-Band Unwanted Emissions, Conducted Test Method:
ANSI C63.17, clause 6.1.6.1. Test Results: Complies Measurement Data:
See plots. Requirements, FCC 15.323(d):
B < f 2B :
2B < f 3B :
3B < f UPCS Band Edge : at least 60 dB below max. permitted peak power at least 30 dB below max. permitted peak power at least 50 dB below max. permitted peak power Middle Channel Nemko Norway, Instituttveien 6, Kjeller, Norway Page 22 (48) In-Band Unwanted Emissions, Conducted TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Lower Channel Upper Channel Nemko Norway, Instituttveien 6, Kjeller, Norway Page 23 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 3.12 Out-of-band Emissions, Conducted Test Method:
ANSI C63.17, clause 6.1.6.2. Test Results: Complies Measurement Data:
See plots. Requirements, FCC 15.323(d):
f 1.25MHz outside UPCS band :
1.25MHz f 2.5MHz outside UPCS band :
f 2.5MHz outside UPCS band :
-9.5dBm
-29.5 dBm
-39.5 dBm Lower Channel:
Nemko Norway, Instituttveien 6, Kjeller, Norway Page 24 (48) Out-of-Band Emissions, Conducted Lower Channel:
TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Nemko Norway, Instituttveien 6, Kjeller, Norway Page 25 (48) Out-of-Band Emissions, Conducted Upper Channel:
TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Nemko Norway, Instituttveien 6, Kjeller, Norway Page 26 (48) Out-of-Band Emissions, Conducted Upper Channel:
TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Nemko Norway, Instituttveien 6, Kjeller, Norway Page 27 (48) Out-of-Band Emissions, Conducted Upper Channel:
TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Nemko Norway, Instituttveien 6, Kjeller, Norway Page 28 (48) Out-of-Band Emissions, Conducted Upper Channel:
TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Nemko Norway, Instituttveien 6, Kjeller, Norway Page 29 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 3.13 Carrier Frequency Stability Test Method:
ANSI C63.17, clause 6.2.1. Test Results: Complies Measurement Data:
The Frequency Stability is measured with a R&S CMD60 DECT Tester. The CMD60 was logged by a computer programmed to get new readings as fast as possible (about 3 readings per second) over the noted time period or number of readings. The peak-to-peak difference was recorded and the mean value and deviation in ppm was calculated. The Carrier Frequency Stability over Power Supply Voltage and over Temperature is measured with a Frequency Domain Analyzer in histogram mode. Carrier Frequency Stability over Time at Nominal Temperature Average Mean Carrier Frequency (MHz) Max. Diff.
(kHz) Min. Diff.
(kHz) Max. Dev.
(ppm) Limit 1926.726782 7.793 5.690 0.5 10 ppm Deviation ppm = ((Diff.) / Mean Carrier Freq.) x 106 Deviation (ppm) is calculated from 3000 readings. Frequency Stability over Power Supply Voltage at Nominal Temperature Voltage Vnom 85% of Vnom Measured Carrier Frequency (MHz) Difference
(kHz) Deviation
(ppm) 1924.979167 1924.976549
/
-1.1
/
-0.6
-0.8 1924.977240 115% of Vnom Deviation ppm = ((Mean Measured Frequency) / Mean) x 106 Frequency Stability over Temperature
-1.6 Temperature Measured Carrier Frequency (MHz) Difference
(kHz) Deviation
(ppm) T = +20 C T = -20 C T = +50 C 1924.979167 1924.978079 1924.977585 0
-2.6
-1.9 0
-1.4
-1.0 Deviation ppm = ((Mean Measured Frequency) / Mean) x 106 Limit 10 ppm Limit 10 ppm Nemko Norway, Instituttveien 6, Kjeller, Norway Page 30 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 3.14 Frame Repetition Stability Test Method:
ANSI C63.17, clause 6.2.2. Test Results: Complies Measurement Data:
The envelope of the RF signal from the EUT is detected with a Crystal Detector and the mean and standard deviation of the frame repetition frequency is then gated over 100 frames and measured with a Frequency Domain Analyzer. The frame repetition stability is 3 times the standard deviation. Carrier Frequency
(MHz) Mean
(Hz) 1924.992 99.999466 Standard Deviation
(Hz) 0.000015 Frame Repetition Stability (ppm) 0.455 Limit:
Frame Repetition Stability 10 ppm (TDMA) Ref. FCC 15.323(e), ANSI C63.17, clause 6.2.2 3.15 Frame Period and Jitter Test Method:
ANSI C63.17, clause 6.2.3. Test Results: Complies Measurement Data:
Carrier Frequency
(MHz) Frame Period
(ms) 1924.992 99.999 Max Jitter
(s)
-0.037 3xStandard Deviation of Jitter (s)
-0.025 Max Jitter = (1/ (Frame period + Pk-Pk/2)) - (1/Frame Period), when Pk-Pk and Frame Period are in Hz 3xSt.Dev.Jitter = 3x (1/(Frame Period + St.Dev) 1/St.Dev) x 106 Limit:
Frame Period Max Jitter 3 times St.Dev of Jitter Ref. FCC 15.323(e), ANSI C63.17, clause 6.2.3 20 or 10 ms 25 s 12.5 s Nemko Norway, Instituttveien 6, Kjeller, Norway Page 31 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Frame Repetition Stability, Gated over 100 Frames Frame Period and Jitter Nemko Norway, Instituttveien 6, Kjeller, Norway Page 32 (48) 3.16 Monitoring Threshold, Least Interfered Channel TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 Monitoring Threshold Limits:
Lower Threshold:
TL = 15 log B - 184 + 30 - PEUT
(dBm) Upper Threshold:
TU = 15 log B - 184 + 50 - PEUT B is measured Emission Bandwidth in Hz PEUT is measured Transmitter Power in dBm
(dBm) Calculated values:
Lower Threshold Upper Threshold FCC 15.323
-79.7 dBm N/A RSS-213, Issue 2
-80.4 dBm
-60.4 dBm Least Interfered Channel Procedure (LIC) may only be used by systems with more than 20 duplex system access channels. Systems with less than 20 duplex system access channels are not allowed to transmit when interferer level is above Lower Threshold. Upper Threshold has been removed from FCC 15D but still exists in the current Industry Canada RSS-213. Measurement Procedure:
The Upper or Lower Threshold is found by the procedure defined in ANSI C63.17 clause 7.3.1 or 7.3.2. Least Interfered Channel Procedure NOT used:
Lower Threshold Least Interfered Channel Procedure:
Upper Threshold N/A dBm
-63.0 dBm Least Interfered Channel (LIC) Procedure Test, FCC 15.323(b), (c)(2) and (c)(5) ANSI C63.17 clause 7.3.3 ref. b) f1 TL + 13 dB, f2 at TL + 6 dB c) f1 TL + 6 dB, f2 at TL + 13 dB d) f1 TL + 7 dB, f2 at TL e) f1 TL, f2 at TL + 7 dB Observation Verdict Transmission always on f2 Transmission always on f1 Transmission always on f2 Transmission always on f1 Pass Pass Pass Pass Nemko Norway, Instituttveien 6, Kjeller, Norway Page 33 (48) Selected Channel Confirmation, FCC 15.323(c)(1) and (5) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 ANSI C63.17 clause 7.3.4 b) Shall not transmit on f1 d) Shall not transmit on f2 Observation EUT transmits on f2 EUT transmits on f1 Verdict Pass Pass Limits:
Lower Threshold + 6 dB margin Upper Threshold + 6 dB margin FCC 15.323
-73.7 dBm N/A RSS-213, Issue 2
-74.4 dBm
-54.4 dBm
*
1 PK CLRWR DELTA MARKER 2 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s 3.03 s Ref 0 dBm
*
Att 10 dB RBW 300 kHz VBW 1 MHz SWT 5 s Delta 2 [T1 ]
30.77 dB 3.030000 s Marker 1 [T1 ]
-50.58 dBm 329.924000 ms 2 A SGL TRG 0
-10
-20
-30
-40 1
-50
-60
-70
-80
-90
-100 Center 1.923264 GHz 500 ms/
Date: 12.MAY.2014 14:33:00 7.3.4 Selected Channel Confirmation, Connection 3.0s After Interferer Removed Nemko Norway, Instituttveien 6, Kjeller, Norway Page 34 (48) 3.17 Threshold Monitoring Bandwidth TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 This test is only required if a dedicated monitoring receiver is used. However, if the test is not carried out the manufacturer shall declare and provide proper evidence that the monitoring is made through the radio receiver used for communication. Measurement Procedure:
Simple Compliance Test, ANSI C63.17, clause 7.4.1 More Detailed Test, ANSI C63.17, clause 7.4.2 The test is passed if either the Simple Compliance Test or the More Detailed test is passed. During this test the spectrum analyzer is observed visually to see if the EUT transmits or not. Test Results:
Test performed Observation Verdict Simple Compliance test, at 30% of B No transmissions More Detailed Test, at -6 dB points More Detailed Test, at -12 dB points N/A N/A Pass N/A N/A The more detailed test must be pass at both the -6 and -12 dB points if the Simple Compliance test fails. Comment: The Simple Compliance Test was performed with the level at TU + UM + 10 dB to check that the EUT did not transmit at all. The tested EUT uses the same receiver for monitoring and communication, this test is therefore not required. However the test has been performed nonetheless and the test is passed. Limits, FCC 15.323(c)(7):
The monitoring system bandwidth must be equal to or greater than the emission bandwidth of the intended transmission. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 35 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 3.18 Reaction Time and Monitoring Interval Measurement Procedure ANSI C63.17, clause 7.5 Test results:
By administrative commands and out-of-operating region interference, the EUT is restricted to operate on a single carrier frequency. Time-synchronized pulsed interference was then applied on the carrier at pulsed levels TU + UM to check that the EUT does not transmit at all. The level was raised 6 dB for part d) with 35 s pulses. The pulses are synchronized with the EUT timeslots and applied centered within all timeslots. Pulse Width, ref. to ANSI C63.17 clause 7.5 Observation c) > largest of 50 s and 50*SQRT(1.25/B) d) > largest of 35 s and 35*SQRT(1.25/B), and with interference level raised 6 dB No transmissions No transmissions Verdict Pass Pass Comment: Since B is larger than 1.25 MHz the test was performed with pulse lengths of 50 s and 35 s. Limits, FCC 15.323(c)(1), (5) and (7) The maximum reaction time must be less than 50xSQRT (1.25/emission bandwidth in MHz) microseconds for signals at the applicable threshold level but shall not be required to be less than 50 microseconds. If a signal is detected that is 6 dB or more above the applicable threshold level, the maximum reaction time shall be 35xSQRT (1.25/emission bandwidth in MHz) microseconds but shall not be required to be less than 35 microseconds. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 36 (48) Ref 0 dBm
*
Att 10 dB RBW 1 MHz VBW 3 MHz SWT 10 ms TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600
*
1 PK CLRWR 0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100 Center 1.923264 GHz 1 ms/
Date: 12.MAY.2014 14:26:59 50 s Pulses Ref 0 dBm
*
Att 10 dB RBW 1 MHz VBW 3 MHz SWT 10 ms
*
1 PK CLRWR 0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100 Center 1.923264 GHz 1 ms/
Date: 12.MAY.2014 14:27:36 35 s Pulses A TRG A TRG Nemko Norway, Instituttveien 6, Kjeller, Norway Page 37 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 3.19 Time and Spectrum Window Access Procedure This requirement is only for EUTs which transmit unacknowledged control and signaling information. Measurement Procedure:
Timing for EUTs using control and signaling channel type transmissions: ANSI C63.17, clause 8.1 Test results:
Access Criteria, ref. to ANSI C63.17 clause 8.1.1 Observation Verdict b) Check that the EUT transmits on the interference free time-slot b) The EUT must terminate or pause in its repetitive transmission of the control and signalling channel on the open channel to repeat the access criteria not less frequently than every 30 s N/A N/A N/A N/A If FCC 15.323(c)(6) option, If Random Waiting Interval is NOT implemented Access Criteria, ref. to ANSI C63.17 clause 8.1.2 Observation b) Check that the EUT changes to an interference-free slot when interference is introduced on the time slot in use N/A If FCC 15.323(c)(6) option, Only if Random Waiting Interval is implemented Access Criteria, ref. to ANSI C63.17 clause 8.1.3 Observation b-d) Check that the EUT uses random waiting interval before continuing transmission on an interfered time slot N/A Verdict N/A Verdict N/A Comment: The tested EUT does not transmit unacknowledged control and signaling information. Limits:
FCC 15.323(c)(4):
Once access to specific combined time and spectrum windows is obtained an acknowledgement from a system participant must be received by the initiating transmitter within one second or transmission must cease. Periodic acknowledgements must be received at least every 30 seconds or transmission must cease. Channels used exclusively for control and signaling information may transmit continuously for 30 seconds without receiving an acknowledgement, at which time the access criteria must be repeated. FCC 15.323(c)(6):
If the selected combined time and spectrum windows are unavailable, the device may either monitor and select different windows or seek to use the same windows after waiting an amount of time, randomly chosen from a uniform random distribution between 10 and 150 milliseconds, commencing when the channel becomes available Nemko Norway, Instituttveien 6, Kjeller, Norway Page 38 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 3.20 Acknowledgements and Transmission Duration Measurement Procedure:
Acknowledgements: ANSI C63.17, clause 8.2.1 Transmission Duration: ANSI C63.17, clause 8.2.2 During the test Initial transmission without acknowledgements the signal from the EUT to the companion device is blocked by circulators in addition to the tunable attenuator. The test Transmission time after loss of acknowledgements is performed by cutting-off the signal from the companion device by a RF switch and measuring the time until the EUT stops transmitting. The Transmission Duration test is performed by monitoring the slot in use and measuring the time until the EUT changes to a different slot. Test Results:
Acknowledgements Test ref. to ANSI C63.17 clause 8.2.1 Observation Verdict a) Initial transmission without acknowledgements c) Transmission time after loss of acknowledgements 0.32 sec 10.0 sec Pass Pass Transmission Duration Test ref. to ANSI C63.17 clause 8.2.2 b) Transmission duration on same time and frequency window Comment: *EUT stops transmitting after 2 minutes. Limits, FCC 15.323(c)(3) and (4) Observation 2 minutes*
Verdict Pass Occupation of the same combined time and spectrum windows by a device or group of cooperating devices continuously over a period of time longer than 8 hours is not permitted without repeating the access criteria. Once access to specific combined time and spectrum windows is obtained an acknowledgement from a system participant must be received by the initiating transmitter within one second or transmission must cease. Periodic acknowledgements must be received at least every 30 seconds or transmission must cease. Channels used exclusively for control and signaling information may transmit continuously for 30 seconds without receiving an acknowledgement, at which time the access criteria must be repeated. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 39 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 DELTA MARKER 2 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms 324 ms Ref 0 dBm
*
Att 10 dB RBW 1 MHz VBW 3 MHz SWT 2 s Delta 2 [T1 ]
-0.00 dB 324.000000 ms Marker 1 [T1 ]
-18.93 dBm 1.447924 s 1 2 A SGL TRG
*
1 PK CLRWR 0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100 Center 1.923264 GHz 200 ms/
Date: 12.MAY.2014 14:05:34 8.2.1a) Initial Transmission Without Acknowledgements
*
1 PK CLRWR DELTA MARKER 2 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s 9.992 s Ref 0 dBm
*
Att 10 dB RBW 1 MHz VBW 3 MHz SWT 12 s Delta 2 [T1 ]
-0.21 dB 9.992000 s Marker 1 [T1 ]
-18.07 dBm 1.179924 s 2 A SGL TRG 1 0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100 Center 1.923264 GHz 1.2 s/
Date: 12.MAY.2014 13:43:01 8.2.1c) Transmission Time After Loss of Acknowledgements Nemko Norway, Instituttveien 6, Kjeller, Norway Page 40 (48) 3.21 Dual Access Criteria Check Measurement Procedure:
TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 EUTs that does not implement the Upper Threshold: ANSI C63.17, clause 8.3.1 EUTs that implement the Upper Threshold: ANSI C63.17, clause 8.3.2 This test is required for equipment that uses the access criteria in FCC 15.323(c)(10). Test Results:
EUTs that Implements the Upper Threshold:
Test ref. to ANSI C63.17 clause 8.3.2 b) EUT is restricted to a single carrier f1 for TDMA systems. The Test is Pass if EUT can transmit c) d) Transmission on interference-free receive time/spectrum window e) f) Transmission on interference-free transmit time/spectrum window g) Transmission not possible on any time/spectrum window Comment: See plots. Limits, FCC 15.323(c)(10) Observation EUT can transmit EUT transmits on interference free receive slot EUT transmits on interference free transmit slot Verdict Pass Pass Pass No connection possible Pass An initiating device may attempt to establish a duplex connection by monitoring both its intended transmit and receive time and spectrum windows. If both the intended transmit and receive time and spectrum windows meet the access criteria, then the initiating device can initiate a transmission in the intended transmit time and spectrum window. If the power detected by the responding device can be decoded as a duplex connection signal from the initiating device, then the responding device may immediately begin transmitting on the receive time and spectrum window monitored by the initiating device. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 41 (48) RESOLUTION BANDWIDTH 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz Ref 0 dBm
*
Att 10 dB RBW 300 kHz VBW 1 MHz SWT 10 ms TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600
*
1 PK CLRWR 0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100 Center 1.923264 GHz 1 ms/
Date: 12.MAY.2014 14:09:13 8.3.2c) EUT Transmits on Interference Free RECEIVE Slot, BEFORE
*
1 PK CLRWR RESOLUTION BANDWIDTH 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz Ref 0 dBm
*
Att 10 dB RBW 300 kHz VBW 1 MHz SWT 10 ms 0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100 Center 1.923264 GHz 1 ms/
Date: 12.MAY.2014 14:10:22 8.3.2c) EUT Transmits on Interference Free RECEIVE Slot, AFTER A TRG A TRG Nemko Norway, Instituttveien 6, Kjeller, Norway Page 42 (48) RESOLUTION BANDWIDTH 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz Ref 0 dBm
*
Att 10 dB RBW 300 kHz VBW 1 MHz SWT 10 ms TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600
*
1 PK CLRWR 0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100 Center 1.923264 GHz 1 ms/
Date: 12.MAY.2014 14:12:33 8.3.2e) EUT Transmits on Interference Free TRANSMIT Slot, BEFORE
*
1 PK CLRWR RESOLUTION BANDWIDTH 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz Ref 0 dBm
*
Att 10 dB RBW 300 kHz VBW 1 MHz SWT 10 ms 0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100 Center 1.923264 GHz 1 ms/
Date: 12.MAY.2014 14:13:07 8.3.2e) EUT Transmits on Interference Free TRANSMIT Slot, AFTER A TRG A TRG Nemko Norway, Instituttveien 6, Kjeller, Norway Page 43 (48) RESOLUTION BANDWIDTH 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz 300 kHz Ref 0 dBm
*
Att 10 dB RBW 300 kHz VBW 1 MHz SWT 10 ms TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600
*
1 PK CLRWR 0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100 Center 1.923264 GHz 1 ms/
Date: 12.MAY.2014 14:11:57 8.3.2g) No Connection A TRG Nemko Norway, Instituttveien 6, Kjeller, Norway Page 44 (48) 3.22 Alternative Monitoring Interval Test procedure described in ANSI C63.17 clause 8.4. TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 This test is required if the EUT implements the provisions of FCC 15.323(c)(11). Test result:
Not Tested. The tested EUT does not implement this provision. See manufacturers declaration. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 45 (48) TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 4 Test Setups 4.1 Frequency Measurements EUT Test equipment included: 5, 9, 19, 22, 28 Test Set-up 1 Modulation Domain Analyzer This setup is used for measuring Carrier frequency stability at normal and extreme temperatures. 4.2 Timing Measurements Crystal Detector EUT Test equipment included: 5, 7, 9, 19, 22 Test Set-up 2 Modulation Domain Analyzer This setup is used for measuring Frame repetition stability, Frame period and Jitter. 4.3 Conducted Emission Test EUT 10 dB Spectrum Analyzer Test equipment included: 1, 2, 9, 19, 22, 26 Test Set-up 3 This setup is used for all conducted emission tests. 4.4 Power Line Conducted Emissions Test Shielded Room EUT LISN Test Receiver Test equipment: 8, 17, 19, 22, 27 Test Set-Up 5 Nemko Norway, Instituttveien 6, Kjeller, Norway Page 46 (48) 4.5 Monitoring Tests TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 EUT 10 dB Combining Device Tunable Attenuator Shielded Room Companion Device Generator 1 Generator 2 Generator 3 Spectrum Analyzer CLK100 Pulse Pattern Generator Sync signal Test equipment: 2, 3, 4, 6, 9, 10, 11, 12, 13, 14, 15, 19, 23, 24, 25, 26, 29 Test Set-Up 6 This test setup is used for all Monitoring and Time and Spectrum Access Procedure tests. The path loss from the signal generators to the EUT is measured with a power meter before the testing is started. The CLK100 is used to synchronize the Pulse-/ Pattern generator to the start of the DECT frame, this signal always comes from the base station. If the EUT is a DECT Portable Part (i.e. a handset) the CLK100 signal will come form the Companion Device. The sync signal to the Spectrum Analyzer is the CLK100 signal that is regenerated in the Pulse-/ Pattern Generator, this is used to synchronize the Spectrum Analyzer to the DECT frame when in zero span. The Pulse-/ Pattern Generator is used for tests that require time synchronized pulses or blocking of specific time slots. Nemko Norway, Instituttveien 6, Kjeller, Norway Page 47 (48) Test Equipment Used 5 TEST REPORT FCC part 15D Report no.: 258223-5 FCC ID: ACJ96NKX-HNC600 To facilitate inclusion on each page of the test equipment used for related tests, each item of test equipment and ancillaries are identified (numbered) by the Testhouse. FSW26 SME03 SMIQ03B SMHU52 53310A 81104A 8470B ESHS10 4768-10 745-69 No. Model number 1 2 3 4 5 6 7 8 9 10 11 WE 1506A 12 WE 1506A 13 14 15 17 19 22 Model 87 V 23 24 25 26 27 28 29 87H35-1 87H35-1 87H35-1 U2000A ESH3-Z2 CMD60 FSP30 H-9 H-9 S212DS ESH3-Z5 6812B Description Spectrum Analyzer Signal generator Signal generator Signal generator Modulation Domain Analyzer Pulse-/ Pattern Generator Crystal Detector Measuring Receiver Attenuator Step Attenuator Power Splitter Power Splitter Hybrid Hybrid RF Switch Two Line V-Network AC Power Source Multimeter Circulator Circulator Circulator USB Average Power Sensor Pulse Limiter DECT Tester Spectrum Analyzer Manufacturer Rohde & Schwarz Rohde & Schwarz Rohde & Schwarz Rohde & Schwarz Hewlett Packard Agilent Hewlett Packard Rohde & Schwarz Narda Narda Weinchel Weinchel Anzac Anzac Narda Rohde & Schwarz Agilent Fluke Racal-MESL Racal-MESL Racal-MESL Agilent Rohde & Schwarz Rohde & Schwarz Rohde & Schwarz Ref. no. LR 1504 LR 1238 LR 1516 LR 1240 LR 1483 LR 1502 LR 1207 N- 3528 LR1356 LR 1442 LR 244 LR 245 LR 86 LR 257 LR 1244 LR 1076 LR 1515 N-4670 s.no.: 140 s.no.: 141 s.no.: 142 LR 1523 LR 1074 LR 1335 LR1551 Cal. date Cal. Due 2014.08.30 2013.08.30 2015.03.19 2013.03.19 2012.11.02 2014.11.02 Cal b4 use 2015.08.14 2013.08.14 2015.03.19 2013.03.19 N/A 2014.06.28 2012.06.28 Cal b4 use N/A Cal b4 use Cal b4 use Cal b4 use Cal b4 use N/A Cal b4 use 2014.10.28 2013.10.28 2013.10.07 2014.10.07 N/A N/A N/A 2013.10.23 2015.10.23 Cal b4 use 2014.11.01 2012.11.01 2013.02.25 2015.02.25 Nemko Norway, Instituttveien 6, Kjeller, Norway Page 48 (48)
| 1 | User Manual | Users Manual | 369.69 KiB | / September 08 2014 |
Installation Guide Wireless Outdoor Camera Model No. KX-HNC600 Thank you for purchasing a Panasonic product. Please read this document before using the unit and save it for future reference. For assistance, visit our Web site: http://www.panasonic.com/help for customers in the U.S.A. or Puerto Rico. Installation For your safety To prevent severe injury and loss of life/
property, read this section carefully before using the product to ensure proper and safe operation of your product. WARNING Power connection R Use only the power source marked on the product. R Do not overload power outlets and extension cords. This can result in the risk of fire or electric shock. R Completely insert the AC adaptor/power plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire. R Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire. R Unplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact us at www.panasonic.com/contactinfo R Unplug from power outlets and never touch the inside of the product if its casing has been broken open. R Never touch the plug with wet hands. Danger of electric shock exists. Installation R Do not allow the AC adaptor cord to be excessively pulled, bent or placed under heavy objects. R Do not connect a power cable to a terminal that is not specified in this guide. R When opening holes in walls for installation or wiring, or when securing the power cable, make sure you do not damage existing wiring and ductwork. R Do not perform any actions (such as fabricating, twisting, stretching, bundling, forcibly bending, damaging, altering, exposing to heat sources, or placing heavy objects on the power cable) that may damage the power cable. Using the product with a damaged power cable may cause electric shock, short circuits, or fire. Contact an authorized service center for repairs. R Do not mount the bracket in an unstable location, in a location subject to frequent vibration, on a ceiling, or on a weak wall.
(Do not mount on plaster board, concrete blocks, wooden materials exposed to the outdoors, walls with very rough surfaces, or surfaces that are narrower than the width of the wall mount bracket.) There is a risk of injury if the product falls, or of fire or electric shock if water enters the product. R The safety wire must be used when mounting the product. There is a risk of injury if the product falls. Operating safeguards R Unplug the product from power outlets before cleaning. Do not use liquid or aerosol cleaners. R Do not disassemble the product. R Keep the sensor range caps out of the reach of children. There is a risk of swallowing. In the event they are swallowed, seek medical advice immediately. R Never put metal objects inside the product. If metal objects enter the product, turn off the circuit breaker and contact an authorized service center. Medical R Consult the manufacturer of any personal medical devices, such as pacemakers or hearing aids, to determine if they are adequately shielded from external RF
(radio frequency) energy. DECT features operate between 1.92 GHz and 1.93 GHz with a peak transmission power of 115 mW. Wi-Fi features operate between 2.412 GHz and 2.462 GHz with a peak transmission power of 100 mW. R Do not use the product in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy. CAUTION Installation and location R Never install wiring during an electrical storm. R The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible. 2 For assistance, please visit http://www.panasonic.com/help R If the wiring is underground, do not make R Do not allow the lens cover or the heat Installation sensor to become scratched or dirty. (This may cause image quality to be reduced, incorrect detections, malfunctions, or damage to the lens cover and heat sensor.) R Do not expose this product to direct sunlight or other forms of powerful light such as halogen lights for long periods of time. (This may damage the image sensor.) Routine care R Wipe the outer surface of the product with a R Do not use benzine, thinner, or any soft moist cloth. abrasive powder. Camera image quality R Camera images may have the following characteristics. Colors in images may differ from the actual colors. When there is light behind the subject
(i.e., backlighting), faces may appear dark. Image quality may be reduced in dark locations. Images may appear hazy when there are outdoor lights in use. R Distinguishing faces is difficult in the following situations. When the person is too far (over approx. 9.8 ft. [3 m]) from the camera even when the surrounding area is bright.
(Depending on the viewing angle or the conditions when images were viewed, such as when there are shadows or backlighting, faces may not be distinguishable even when the person is within 9.8 ft. [3 m] of the camera.) In the late afternoon and at night, or other times when the surrounding area is dark. (This may reduce image quality.) When people are moving (which causes blurring) in front of the camera. any connections underground. R If the wiring is underground, make sure the power cable and other wiring is properly waterproofed by running the cables through a conduit. Preventing accidents and injuries R Do not put your ear(s) near the speaker, as loud sounds emitted from the speaker may cause hearing impairment. R Do not look directly at the LED lights when they are lit. Failure to do so may cause damage to eyes. Important safety instructions When using your product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
1. Use only the power cord in this document. SAVE THESE INSTRUCTIONS For best performance Base unit location/avoiding noise The base unit and other compatible Panasonic units use radio waves to communicate with each other. Environment R Keep the product away from electrical noise generating devices, such as fluorescent lamps and motors. R The product should be kept free from excessive smoke, dust, high temperature, and vibration. R Do not place heavy objects on top of the product. R When you leave the product unused for a long period of time, unplug the product from the power outlet. R The product should be kept away from heat sources such as heaters, kitchen stoves, etc. It should not be placed in rooms where the temperature is less than 0 C (32 F) or greater than 40 C (104 F). Damp basements should also be avoided. For assistance, please visit http://www.panasonic.com/help 3 Installation Notice:
4 For assistance, please visit http://www.panasonic.com/help This product is designed for use in the United States of America. Sale or use of this product in other countries may violate local laws. Cet appareil est conu pour tre utilis aux tats-Unis dAmrique. La vente ou lemploi de cet appareil dans certains autres pays peut constituer une infraction la lgislation locale. Este producto est diseado para usarse en los Estados Unidos de Amrica.La venta o el empleo de este producto en ciertos pases puede constituir violacin de la legislacin local. Installation further away from the TV or VCR. This will often reduce or eliminate interference. FCC RF Exposure Warning:
R This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. R To comply with FCC RF exposure requirements, the base unit must be installed and operated 20 cm (8 inches) or more between the product and all persons body. R This product may not be collocated or operated in conjunction with any other antenna or transmitter. R For body-worn operation, the handset must be used only with a non-metallic accessory. Use of other accessories may not ensure compliance with FCC RF exposure requirements. Notice:
R FCC ID can be found inside the battery compartment or on the bottom of the units. FCC and other information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this phone. CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this device. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/
TV technician for help. Some cordless telephones operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, the base of the cordless telephone should not be placed near or on top of a TV or VCR. If interference is experienced, move the cordless telephone For assistance, please visit http://www.panasonic.com/help 5 Setup Physical features Installation 1 Attach the safety wire to the rear of the camera. 2 Attach the stand to the outside wall. Safety wire Stand DC cable Lens unit Microphone Infrared sensor Sensor area adjustment cap Status light Speaker Registration button 3 Attach the safety wire to the outside wall. 4 Attach the camera to the stand. 5 Adjust the position of the camera. 6 Insert the DC cable through the wall and connect it to the AC adaptor. 6 For assistance, please visit http://www.panasonic.com/help CFEDGHBAJIxx mm(xx in.)xx mm(xx in.) Setup and appropriate water protection measures are taken. Do not install the camera in areas directly exposed to water or rain.
*5 Adjustable when mounting. Specifications R Frequency range DECT:
1.92 GHz1.93 GHz Wi-Fi:
2.412 GHz2.462 GHz (channels 111) R Power source 120 V AC, 60 Hz R Operating conditions
-20 C50 C (-4 F122F) up to 90% relative air humidity
(non-condensing) R Transmitting range Approx. 100 m (328 feet) (line-of-sight distance from the base unit) R Image sensor 0.3 megapixel CMOS R Minimum illuminance required 1 lx*1 R Focal length Fixed, 0.4 m (1.3 feet)infinity) R Angular field of view (camera angle) Horizontal: approx. 70 Vertical: approx. 53 R Sensor detection method Pyroelectric infrared sensor (heat sensor) and motion detection R Heat sensor detection range*2 Horizontal: approx. 63 Vertical: approx. 20 Distance: approx. 5 m (16.4 feet) R Motion detection sensor detection range Horizontal: approx. 53 Vertical: approx. 41 R Lighting method 2 white LED lights*3 R IP rating IP55*4 R Adjustable mounting angles*5 Horizontal: 90 Vertical: facing forward - facing down approx. 60 R Heat sensor adjustable angles Manually adjustable to 2 angles
*1 The minimum illuminance required when the cameras [Brightness] setting is set to
[+3].
*2 When the surrounding temperature is approx. 20 C (68 F).
*3 Approx. 8.5 lx when 3 m (9.8 feet) in front of the camera, and approx. 4 lx when 3 m
(9.8 feet) away and 20 to the left or right of the camera.
*4 Water resistance is only assured if the camera is installed correctly according to the instructions in the Installation Guide, For assistance, please visit http://www.panasonic.com/help 7 Two Riverfront Plaza, Newark, NJ 07102-5490 Panasonic System Networks Co., Ltd. 2014Printed in China
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2014-06-24 | 1921.536 ~ 1928.448 | PUB - Part 15 Unlicensed PCS Base Station | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2014-06-24
|
||||
| 1 | Applicant's complete, legal business name |
Panasonic Corporation of North America
|
||||
| 1 | FCC Registration Number (FRN) |
0003762242
|
||||
| 1 | Physical Address |
Two Riverfront Plaza, 9th Floor
|
||||
| 1 |
Newark, New Jersey 07102-5490
|
|||||
| 1 |
United States
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
s******@nemko.com
|
||||
| 1 | TCB Scope |
A3: Unlicensed Personal Communication System (PCS) devices
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
ACJ
|
||||
| 1 | Equipment Product Code |
96NKX-HNC600
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
B******** B********
|
||||
| 1 | Title |
Project Manager
|
||||
| 1 | Telephone Number |
201-3********
|
||||
| 1 | Fax Number |
201-3********
|
||||
| 1 |
B******@us.panasonic.com
|
|||||
| app s | Technical Contact | |||||
| n/a | ||||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 08/09/2014 | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | PUB - Part 15 Unlicensed PCS Base Station | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | DECT 6.0 Outdoor Camera | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | Yes | ||||
| 1 | Grant Comments | Power listed is conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter except as described in this filing. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Nemko AS
|
||||
| 1 | Name |
F**** S****
|
||||
| 1 | Telephone Number |
47-22********
|
||||
| 1 | Fax Number |
47-22********
|
||||
| 1 |
f******@nemko.com
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 15D | 1921.53600000 | 1928.44800000 | 0.0620000 | ||||||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC