all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User man | Users Manual | 1.06 MiB | May 09 2017 | |||
1 | Attestation Statements | May 09 2017 | ||||||
1 | Cover Letter(s) | May 09 2017 | ||||||
1 | Cover Letter(s) | May 09 2017 | ||||||
1 | External Photos | May 09 2017 | ||||||
1 | Internal Photos | May 09 2017 | ||||||
1 | ID Label/Location Info | May 09 2017 | ||||||
1 | ID Label/Location Info | May 09 2017 | ||||||
1 | Attestation Statements | May 09 2017 | ||||||
1 | Test Report | May 09 2017 | ||||||
1 | Test Setup Photos | May 09 2017 |
1 | User man | Users Manual | 1.06 MiB | May 09 2017 |
PAN1760A Bluetooth Low Energy Module Product Specification Rev. 1.0 Wireless Modules PAN1760A Bluetooth Module Overview Bluetooth The PAN1760A is Panasonics next generation Bluetooth module with the industrys lowest power Bluetooth Low Energy SoC. Features Small 15.6 mm x 8.7 mm x 1.9 mm SMD module Same form factor and pinout as PAN1026, PAN1760, and PAN1761 Bluetooth Low Energy 4.2 compliant Embedded 256 kB flash memory and 192 kB internal RAM GAP central and peripheral support for LE GATT, SMP, and SDB support for LE Over-the-Air firmware update Support for Scatternet/Mesh network BT 4.2 secure connections support through Elliptic-Curve-DH Cryptography AES-128 hardware encryption (FIPS-approved) Frequent changing of device address (improved privacy, reduced tracking ability) Larger packet sizes (more efficient application and network layer security) 83 kB RAM available for user application AT Command mode, Host mode, Stand-Alone Characteristics mode Standard SIG BLE profiles as well as SPPoverBLE profile UART (2x), SPI & I2C interface, PWM output (4x), ADC (5 ext, 1 int), 17 programmable I/O ARM Cortex-M0 processor with Single Wire Debug (SWD) interface Receiver sensitivity -93 dBm typ. Output power 0 dBm maximum setting Power supply 1.8 V to 3.6 V single operation voltage Transmit and receive 3.3 mA Tx/Rx peak power consumption Low Power 50 nA Deep Sleep mode Operating temperature range -40 C to +85 C Block Diagram Product Specification Rev. 1.0 Page 2 ChipAntennaToshibaTC35678Slow Clock32 KHzUARTGPIOsHost Wake upWake upReset Vcc 3.3 VLPFPAN1760ABluetooth 4.2 ModuleCrystal26 MHzDC-DCConversionFlash256 kBSWD PAN1760A Bluetooth Module By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design. Panasonic Industrial Devices Europe GmbH 2017. This specification sheet is copyrighted. Reproduction of this document is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Do not disclose it to a third party. All rights reserved. This Product Specification does not lodge the claim to be complete and free of mistakes. Engineering Samples (ES) If Engineering Samples are delivered to the customer, these samples have the status Engineering Samples. This means that the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and they may differ from the published Product Specification. Engineering Samples are not qualified and they are not to be used for reliability testing or series production. Disclaimer The customer acknowledges that samples may deviate from the Product Specification and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by:
The use of the Engineering Sample other than for evaluation purposes, particularly the installation or integration in another product to be sold by the customer, Deviation or lapse in function of the Engineering Sample, Improper use of the Engineering Sample. Panasonic Industrial Devices Europe GmbH disclaims any liability for consequential and incidental damages. In case of any queries regarding the Engineering Samples, please contact your local sales partner or the related product manager. Product Specification Rev. 1.0 Page 3 PAN1760A Bluetooth Module Table of Contents 1 About This Document ......................................................................................................................... 5 Purpose and Audience .............................................................................................................. 5 1.1 Revision History ......................................................................................................................... 5 1.2 1.3 Use of Symbols ......................................................................................................................... 5 Related Documents ................................................................................................................... 5 1.4 2 Overview .............................................................................................................................................. 6 Block Diagram ........................................................................................................................... 7 Pin Configuration ....................................................................................................................... 8 UART Interface ........................................................................................................................ 10 Bluetooth Features .................................................................................................................. 10 2.1 2.2 2.3 2.4 3 4 5 6 7 Detailed Description ......................................................................................................................... 11 Dimensions .............................................................................................................................. 11 3.1 Footprint .................................................................................................................................. 12 3.2 3.3 Packaging ................................................................................................................................ 13 Case Marking .......................................................................................................................... 16 3.4 Specification ..................................................................................................................................... 17 4.1 Default Test Conditions ........................................................................................................... 17 Absolute Maximum Ratings ..................................................................................................... 17 4.2 Recommended Operating Conditions ...................................................................................... 18 4.3 Current Consumption............................................................................................................... 18 4.4 4.5 Bluetooth ................................................................................................................................. 19 Reliability Tests ....................................................................................................................... 19 4.6 4.7 Recommended Soldering Profile ............................................................................................. 20 Cautions ............................................................................................................................................ 21 Design Notes ........................................................................................................................... 21 5.1 Installation Notes ..................................................................................................................... 21 5.2 5.3 Usage Condition Notes ............................................................................................................ 22 Storage Notes .......................................................................................................................... 22 5.4 5.5 Safety Cautions ....................................................................................................................... 22 5.6 Other Cautions ........................................................................................................................ 23 5.7 Life Support Policy ................................................................................................................... 23 Regulatory and Certification Information ....................................................................................... 24 Federal Communications Commission (FCC) for US .............................................................. 24 6.1 6.2 Innovation, Science, and Economic Development (ISED) for Canada .................................... 26 European Conformity According to RED (2014/53/EU) ........................................................... 29 6.3 6.4 RoHS and REACH Declaration ............................................................................................... 29 Appendix ........................................................................................................................................... 30 7.1 Ordering Information ................................................................................................................ 30 7.2 Contact Details ........................................................................................................................ 31 Product Specification Rev. 1.0 Page 4 PAN1760A Bluetooth Module 1 About This Document 1 About This Document 1.1 Purpose and Audience This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic PAN1760A module. It is intended for hardware design, application, and Original Equipment Manufacturers (OEM) engineers. The product is referred to as the PAN1760A or the module within this document. 1.2 Revision History Revision Date Modifications/Remarks 0.1 0.2 1.0 23.05.2017 1st preliminary version 12.06.2017 Editorial review 12.06.2017 First published version 1.3 Use of Symbols Symbol Description Note Indicates important information for the proper use of the product. Non-observance can lead to errors. Attention Indicates important notes that, if not observed, can put the products functionality at risk.
[chapter number]
[chapter title]
Cross reference Indicates crossreferences within the document. Example:
Description of the symbols used in this document 1.3 Use of Symbols. 1.4 Related Documents Please refer to the Panasonic website for related documents 7.2.2 Product Information. Product Specification Rev. 1.0 Page 5 PAN1760A Bluetooth Module 2 Overview 2 Overview The PAN1760A is Panasonics next generation Bluetooth module with the industrys lowest power Bluetooth Low Energy SoC. The module is based on Toshiba's single chip TC35678 Bluetooth semiconductor device with embedded Toshiba Bluetooth 4.2 LE stack and embedded flash for the user application in stand-alone operation. Peak power consumption of only 3.6 mA in Tx and Rx mode allows advanced wireless functionalities in IoT, medical, and industrial applications without compromising battery life. Mandatory and optional Bluetooth 4.2 features are supported. The PAN1760A can either be operated in AT-Command or Host mode for very simple integration of Bluetooth connectivity into existing products, or in Stand-Alone mode. In Stand-Alone mode, with 256 kB flash memory and 83 kB RAM for user application, the PAN1760A can be used for many applications without the need for an external processor, saving cost, complexity, and space. Older versions of the PAN1760, the PAN1761, and the PAN1026 share the same footprint. Only minor code changes are required when migrating from PAN1026 or PAN1760. Previously developed software (Bluetooth Low Energy profiles and applications) can be easily migrated with a minimal effort. FCC, IC, and CE approval are in preparation. Please refer to the Panasonic website for related documents 7.2.2 Product Information. Further information on the variants and versions 7.1 Ordering Information. Product Specification Rev. 1.0 Page 6 PAN1760A Bluetooth Module 2 Overview 2.1 Block Diagram Total capacitor value: 2.4 F +/-10 %
Total inductance:
10 H +/-10 %
Total resistance:
100 K +/-10 %
Product Specification Rev. 1.0 Page 7 ChipAntennaToshibaTC35678Slow Clock32 KHzUARTGPIOsHost Wake upWake upReset Vcc 3.3 VLPFPAN1760ABluetooth 4.2 ModuleCrystal26 MHzDC-DCConversionFlash256 kBSWD PAN1760A Bluetooth Module 2 Overview Top View 2.2 Pin Configuration Pin Assignment Pin Functions No Pin Name Pin Type Description A1 GND Ground Pin Connect to ground A2 GPIO3 Digital I/O A3 RESET Digital Input Reset, active low A4 NC A5 VCC A6 VCC NC Not connected Power Analog/digital power supply connection Power Analog/digital power supply connection A7 GND Ground Pin Connect to ground A8 NC NC Not connected A9 GND Ground Pin Connect to ground A11 GND Ground Pin Connect to ground A12 GND Ground Pin Connect to ground B1 GPIO9 B2 GPIO4 Digital I/O Digital I/O Product Specification Rev. 1.0 Page 8 F2F3F4F5E1E2E3E4E5E6E7E8E9D1D2D3D4D5D6D7D8C1C2C3C4C5C6C7C8B1B2B3B4B5B6B7B8B9A2A3A4A5A6A7A8A11.08.70 mm0.65.00.61.351.351.2F91.2F7F1F8D9C9A915.6 mmF6F11A11F12A122.4 PAN1760A Bluetooth Module 2 Overview No Pin Name Pin Type Description B3 NC B4 NC B5 GPIO7 B6 GPIO8 NC NC Digital I/O Digital I/O B7 GPIO25 Digital I/O Not connected, leave open Not connected, leave open B8 NC B9 NC C1 NC C2 NC NC NC NC NC Not connected, leave open Not connected, leave open Not connected, leave open Not connected, leave open C3 GPIO10 Digital I/O C4 SWDIO C5 SWDCLK JTAG JTAG C6 GPIO1 Digital I/O C7 NC NC Not connected, leave open C8 GND Ground Pin Connect to ground C9 GND Ground Pin Connect to ground D1 NC D2 NC D3 NC NC NC NC Not connected, leave open Not connected, leave open Not connected, leave open D4 GPIO0/WakeUp0 Digital I/O D5 NC NC Not connected, leave open D6 GPIO15/WakeUp1 Digital I/O D7 GND Ground Pin Connect to ground D8 GND Ground Pin Connect to ground D9 ANT RF-Signal Antenna pin (not connected for standard version) E1 GPIO12/SDA Digital I/O I2C interface E2 GPIO11/SCL Digital I/O I2C interface E3 NC E4 NC NC NC Not connected, leave open Not connected, leave open E5 SLPXOIN Digital Input 32 kHz clock input, leave open E6 GPIO6/UARTRXD Digital Input UART RXD Product Specification Rev. 1.0 Page 9 PAN1760A Bluetooth Module 2 Overview No Pin Name Pin Type Description E7 NC NC Not connected, leave open E8 GND Ground Pin Connect to ground E9 GND Ground Pin Connect to ground F1 GND Ground Pin Connect to ground F2 NC F3 NC F4 NC NC NC NC Not connected, leave open Not connected, leave open Not connected, leave open F5 GPIO14/UARTCTS Digital Input UART CTS F6 GPIO2 Digital I/O F7 GPIO5/UARTTXD Digital Output UART TX F8 GPIO13/UARTRTS Digital Output UART RTS F9 GND Ground Pin Connect to ground F11 GND Ground Pin Connect to ground F12 GND Ground Pin Connect to ground Minimal configuration VCC GND UART Rx, Tx, no flow control 2.3 UART Interface Default baud rate: 115 200 bps Data format: 8N1, LSB first Rx, Tx, no flow control 2.4 Bluetooth Features GAP central and peripheral support for LE GATT, SMP, and SDB support for LE Over-the-Air firmware update Support for Scatternet/Mesh network BT 4.2 secure connections support through Elliptic-Curve-DH Cryptography AES-128 hardware encryption (FIPS-approved) Frequent changing of device address (improved privacy, reduced tracking ability) Larger packet sizes (more efficient application and network layer security) Product Specification Rev. 1.0 Page 10 PAN1760A Bluetooth Module 3 Detailed Description 3 Detailed Description 3.1 Dimensions All dimensions are in millimeters. No. Item Dimension Tolerance Remark 1 Width 2 Length 3 Height 8.70 15.60 1.80 0.20 0.20 0.20 With case Product Specification Rev. 1.0 Page 11 PAN1760A Bluetooth Module 3 Detailed Description 3.2 Footprint The outer dimensions have a tolerance of 0.2 mm. Top View Product Specification Rev. 1.0 Page 12 F2F3F4F5E1E2E3E4E5E6E7E8E9D1D2D3D4D5D6D7D8C1C2C3C4C5C6C7C8B1B2B3B4B5B6B7B8B9A2A3A4A5A6A7A8A11.08.70 mm0.65.00.61.351.351.2F91.2F7F1F8D9C9A915.6 mmF6F11A11F12A122.4 PAN1760A Bluetooth Module 3 Detailed Description 3.3 Packaging The product is a mass production status product and will be delivered in the package described below. 3.3.1 Tape Dimensions 3.3.2 Packing in Tape Empty spaces in the component packed area shall be less than two per reel and those spaces shall not be consecutive. The top cover tape shall not be found on reel holes and it shall not stick out from the reel. Product Specification Rev. 1.0 Page 13 100730-PAN1720.vsdtrailer (empty)1 x circumference /hub(min 160mm)component packed areastandard 1500pcsleader (empty)minimum 10 pitchTop cover tape more than 1 x circumference plus 100mm to avoid fixing of tape end on sealed modules.Direction of unreeling (for customer) PAN1760A Bluetooth Module 3 Detailed Description 3.3.3 Component Direction 3.3.4 Reel Dimension Product Specification Rev. 1.0 Page 14 PAN1760A Bluetooth Module 3 Detailed Description 3.3.5 Package Label Example 3.3.6 Total Package
(1T)
(1P)
(2P)
(9D)
(Q)
(HW/SW) Lot code Customer order number, if applicable Order number Date code Quantity Hardware/software version Product Specification Rev. 1.0 Page 15 3.4 Case Marking Example 1 2 3 4 5 6 7 8 9 PAN1760A Bluetooth Module 3 Detailed Description MIC ID Brand name Hardware/software version Order number FCC ID Lot code Engineering Sample marking, if applicable Marking for Pin 1 2D barcode, for internal usage only Product Specification Rev. 1.0 Page 16 PAN1760A Bluetooth Module 4 Specification 4 Specification All specifications are over temperature and process, unless indicated otherwise. 4.1 Default Test Conditions Temperature:
Humidity:
Supply Voltage:
25 10 C 40 to 85 % RH 3.3 V 4.2 Absolute Maximum Ratings The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter Condition Min. Typ. Max. Units TSTOR VESD PRF VDIG Storage temperature ESD robustness All pads, according to human body model (HBM), JEDEC STD 22, method A114 According to charged device model (CDM), JEDEC STD 22, method C101 RF input level Voltage on any digital pins
-40
+125 C
-0.3 1 000 V 500 V
+10 dBm VDD +
0.3 V Product Specification Rev. 1.0 Page 17 PAN1760A Bluetooth Module 4 Specification 4.3 Recommended Operating Conditions The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter Condition Min. Typ. Max. Units TA VDD Ambient operating temperature range 3V3 Supply voltage
-40
+85 C 1.8 3.3 3.6 V 4.4 Current Consumption The current consumption depends on the user scenario and on the setup and timing in the power modes. Assume VDD = 3.3 V, Tamb = 25 C, if nothing else stated. Parameter Condition Min. Typ. Max. Units Transmit Peak Current Receive Peak Current Deep Sleep mode 3.3 3.3 50 mA mA nA Product Specification Rev. 1.0 Page 18 4.5 Bluetooth Parameter Condition Operation frequency range Channel spacing BLE PAN1760A Bluetooth Module 4 Specification Min. Typ. Max. Units 2 402 2 480 MHz 2 0 MHz dBm
-93 dBm Typ. Max. Units
<-30 dBm Output Power Maximum setting, measured at dual ended 50 Ohm. Sensitivity Symbol Parameter Condition Min. 1 Spurious emissions Conducted measurement with a 50 dual-ended load. Complies with EN 300 328, EN 300 440 class 2, FCC CFR47, Part 15 and ARIB STD-T-66. 4.6 Reliability Tests The measurement should be done after the test device has been exposed to room temperature and humidity for one hour. No. Item Limit Condition 1 Vibration test Electrical parameter should be in specification 2 Shock test See above 3 Heat cycle test See above Freq.: 10~50 Hz; Amplitude: 1.5 mm;
20 min./cycle, 1 hrs. each of XYZ axis Freq.: 30~100 Hz, 6G; 20 min./cycle, 1 hrs. each of XYZ axis Dropped onto hard wood from a height of 50 cm for 3 times
-40 C for 30 min. and +85 C for 30 min.; each temperature 300 cycles 4 Moisture test See above
+60 C, 90 % RH, 300 h 5 Low temperature test See above 6 High temperature test See above
-40 C, 300 h
+85 C, 300 h Product Specification Rev. 1.0 Page 19 PAN1760A Bluetooth Module 4 Specification 4.7 Recommended Soldering Profile Reflow permissible cycle: 2 Opposite side reflow is prohibited due to module weight More than 75 percent of the soldering area shall be coated by solder The soldering profiles should be adhered to in order to prevent electrical or mechanical damage Soldering profile assumes lead-free soldering Product Specification Rev. 1.0 Page 20 PAN1760A Bluetooth Module 5 Cautions 5 Cautions Failure to follow the guidelines set forth in this document may result in degrading of the products functions and damage to the product. 5.1 Design Notes 1. Follow the conditions written in this specification, especially the control signals of this module. 2. The supply voltage must be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47 uF directly at the module). 3. This product should not be mechanically stressed when installed. 4. Keep this product away from heat. Heat is the major cause of decreasing the life of these products. 5. Avoid assembly and use of the target equipment in conditions where the products temperature may exceed the maximum tolerance. 6. The supply voltage should not be exceedingly high or reversed. It should not carry noise and/or spikes. 7. Keep this product away from other high frequency circuits. 8. Refer to the recommended pattern when designing a board. 5.2 Installation Notes 1. Reflow soldering is possible twice based on the conditions set forth in 4.7 Recommended Soldering Profile. Set up the temperature at the soldering portion of this product according to this reflow profile. 2. Carefully position the products so that their heat will not burn into printed circuit boards or affect the other components that are susceptible to heat. 3. Carefully locate these products so that their temperatures will not increase due to the effects of heat generated by neighboring components. 4. If a vinyl-covered wire comes into contact with the products, then the cover will melt and generate toxic gas, damaging the insulation. Never allow contact between the cover and these products to occur. 5. This product should not be mechanically stressed or vibrated when reflowed. 6. To repair the board by hand soldering, follow the conditions set forth in this chapter. 7. Do not wash this product. 8. Pressing on parts of the metal cover or fastening objects to the metal will cause damage to the unit. Product Specification Rev. 1.0 Page 21 PAN1760A Bluetooth Module 5 Cautions 5.3 Usage Condition Notes 1. Take measures to protect the unit against static electricity. If pulses or other transient loads (a large load applied in a short time) are applied to the products, check and evaluate their operation befor assembly on the final products. 2. Do not use dropped products. 3. Do not touch, damage or soil the pins. 4. Follow the recommended condition ratings about the power supply applied to this product. 5. Electrode peeling strength: Do not add pressure of more than 4.9 N when soldered on PCB. 6. Pressing on parts of the metal cover or fastening objects to the metal cover will cause damage. 7. These products are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information, and communication equipment. 5.4 Storage Notes 1. The module should not be stressed mechanically during storage. 2. Do not store these products in the following conditions or the performance characteristics of the product, such as RF performance will be adversely affected:
Storage in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX, Storage in direct sunlight, Storage in an environment where the temperature may be outside the range of 5 C to 35 C, or where the humidity may be outside the 45 to 85 percent range, Storage of the products for more than one year after the date of delivery storage period: Please check the adhesive strength of the embossed tape and soldering after 6 months of storage. 3. Keep this product away from water, poisonous gas, and corrosive gas. 4. This product should not be stressed or shocked when transported. 5. Follow the specification when stacking packed crates (max. 10). 5.5 Safety Cautions These specifications are intended to preserve the quality assurance of products and individual components. Before use, check and evaluate the operation when mounted on your products. Abide by these specifications without deviation when using the products. These products may short-circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, provide the following failsafe functions as a minimum:
Product Specification Rev. 1.0 Page 22 PAN1760A Bluetooth Module 5 Cautions 1. Ensure the safety of the whole system by installing a protection circuit and a protection device. 2. Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. 5.6 Other Cautions 1. Do not use the products for other purposes than those listed. 2. Be sure to provide an appropriate fail-safe function on your product to prevent any additional damage that may be caused by the abnormal function or the failure of the product. 3. This product has been manufactured without any ozone chemical controlled under the Montreal Protocol. 4. These products are not intended for uses other than under the special conditions shown below. Before using these products under such special conditions, carefully check their performance and reliability under the said special conditions to determine whether or not they can be used in such a manner:
In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash. In direct sunlight, outdoors, or in a dusty environment. In an environment where condensation occurs. In an environment with a high concentration of harmful gas (e. g. salty air, HCl, Cl2, SO2, H2S, NH3, and NOX). 5. If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these products with new products because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. 6. When you have any question or uncertainty, contact Panasonic. 5.7 Life Support Policy This Panasonic Industrial Devices Europe GmbH product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Panasonic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Industrial Devices Europe GmbH for any damages resulting. Product Specification Rev. 1.0 Page 23 PAN1760A Bluetooth Module 6 Regulatory and Certification Information 6 Regulatory and Certification Information 6.1 Federal Communications Commission (FCC) for US 6.1.1 FCC Notice The PAN1760A including the antennas, which are listed in 6.1.5 Approved Antenna List, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. The transmitter operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 6.1.2 Caution The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help Product Specification Rev. 1.0 Page 24 PAN1760A Bluetooth Module 6 Regulatory and Certification Information 6.1.3 Label Requirements The OEM must ensure that FCC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is FCC ID: T7V1760A. This FCC identifier is valid for the PAN1760A. The end product must in any case be labelled on the exterior with:
"Contains FCC ID: T7V1760A"
6.1.4 Antenna Warning This antenna warning refers to the test device with the model number PAN1760A Chapter 7.1 Ordering Information The device is tested with a standard SMA connector and with the antenna listed below. When integrated into the OEMs product, these fixed antennas require installation preventing end users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and with Section 15.247 for emissions. The FCC identifier for the device with the antenna listed in 6.1.5 Approved Antenna List is the same (FCC ID: T7V1760A). 6.1.5 Approved Antenna List Item Part Number Manufacturer Frequency Band Type Gain (dBi) 1 ANT2012 Yageo 2.4GHz Chip-Antenna
+0.9 Product Specification Rev. 1.0 Page 25 PAN1760A Bluetooth Module 6 Regulatory and Certification Information 6.1.6 RF Exposure To comply with FCC RF Exposure requirements, the OEM must ensure that only antennas from the Approved Antenna List are installed 6.1.5 Approved Antenna List. The preceding statement must be included as a CAUTION statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. The radiated output power of the PAN1760A with a mounted ceramic antenna
(FCC ID: T7V1760A) is below the FCC radio frequency exposure limits. Nevertheless, the PAN1760A shall be used in such a manner that the potential for human contact during normal operation is minimized. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. 6.2 Innovation, Science, and Economic Development (ISED) for Canada English The PAN1760A is licensed to meet the regulatory requirements of Industry Canada (IC). License ID:
IC: 216Q-1760A Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca. This device has been designed to operate with the antennas listed in 6.1.5 Approved Antenna List, having a maximum gain of +0.9 dBi. Antennas not included in this list or having a gain greater than +0.9 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Due to the model size, the IC identifier is displayed in the installation instruction only and it cannot be displayed on the modules label due to the limited size. Product Specification Rev. 1.0 Page 26 PAN1760A Bluetooth Module 6 Regulatory and Certification Information French PAN1760A est garanti conforme aux dispositions rglementaires dIndustry Canada (IC). License:
IC: 216Q-1760A Il est recommand aux fabricants dappareils fixes, mobiles ou portables de consulter la rglementation en vigueur et de vrifier la conformit de leurs produits relativement aux limites dexposition aux rayonnements radiofrquence ainsi quau dbit dabsorption spcifique maximum autoris. Des informations pour les utilisateurs sur la rglementation Canadienne concernant lexposition aux rayonnements RF sont disponibles sur le site www.ic.gc.ca. Ce produit a t dvelopp pour fonctionner spcifiquement avec les antennes listes dans le tableau 6.1.5 Approved Antenna List, prsentant un gain maximum de 0.9 dBi. Des antennes autres que celles listes ici, ou prsentant un gain suprieur 0.9 dBi ne doivent en aucune circonstance tre utilises en combinaison avec ce produit. Limpdance des antennes compatibles est 50 Ohm. Lantenne utilise avec ce produit ne doit ni tre situe proximit dune autre antenne ou dun autre metteur, ni tre utilise conjointement avec une autre antenne ou un autre metteur. En raison de la taille du produit, lidentifiant IC est fourni dans le manuel dinstallation. 6.2.1 IC Notice English The device PAN1760A ( 7.1 Ordering Information), including the antennas
( 6.1.5 Approved Antenna List), complies with Canada RSS-GEN Rules. The device meets the requirements for modular transmitter approval as detailed in RSS-Gen. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. French Le prsent appareil PAN1760A ( 7.1 Ordering Information), les antennes y compris ( 6.1.5 Approved Antenna List), est conforme aux CNR-Gen d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Product Specification Rev. 1.0 Page 27 PAN1760A Bluetooth Module 6 Regulatory and Certification Information 6.2.2 Labeling Requirements English Labeling Requirements French The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is:
IC: 216Q-1760A This IC identifier is valid for all PAN1760A modules 7.1 Ordering Information. In any case, the end product must be labelled on the exterior with:
"Contains IC: 216Q-1760A. Obligations dtiquetage Les fabricants dquipements dorigine (FEO) en anglais Original Equipment Manufacturer (OEM) doivent sassurer que les obligations dtiquetage IC du produit final sont remplies. Ces obligations incluent une tiquette clairement visible lextrieur de lemballage externe, comportant lidentifiant IC du module Panasonic inclus, ainsi que la notification ci-dessus. L identifiant IC est:
IC: 216Q-1760A Cet identifiant est valide pour tous les modules PAN1760A 7.1 Ordering Information. Dans tous les cas les produits finaux doivent indiquer sur leur emballage externe la mention suivante:
"Contient IC: 216Q-1760A. Product Specification Rev. 1.0 Page 28 PAN1760A Bluetooth Module 6 Regulatory and Certification Information 6.3 European Conformity According to RED (2014/53/EU) All modules described in this Product Specification comply with the standards according to the following LVD (2014/35/EU), EMC-D (2014/30/EU) together with the RED (2014/53/EU) articles:
3.1a Safety/Health:
EN62368-1:2014 EN62311:2008 3.1b EMC:
3.2 Radio:
EN 301 489-1 V2.1.1:2017-02 EN 301 489-17 V3.1.1:2017-02 EN 300 328 V2.1.1:2016-11 As a result of the conformity assessment procedure described in the 2014/53/EU Directive, the end customer equipment should be labelled as follows:
PAN1760A in the specified reference design can be used in all countries of the European Economic Area (Member States of the EU, European Free Trade Association States [Iceland, Liechtenstein, Norway]), Monaco, San Marino, Andorra and Turkey. 6.4 RoHS and REACH Declaration The latest declaration of environmental compatibility (Restriction of Hazardous Substances, RoHS and Registration, Evaluation, Authorisation and Restriction of Chemicals, REACH) for supplied products can be found on the Panasonic website in the Downloads section of the respective product 7.2.2 Product Information. Product Specification Rev. 1.0 Page 29 PAN1760A Bluetooth Module 7 Appendix 7 Appendix 7.1 Ordering Information Variants and Versions Order Number Brand Name Description ENW89847A3KF2 PAN1760A Bluetooth Low Energy Module MOQ1 1 500 1 Abbreviation for Minimum Order Quantity (MOQ). The default MOQ for mass production is 1 500 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels. 2 Samples are available on customer demand. Product Specification Rev. 1.0 Page 30 PAN1760A Bluetooth Module 7 Appendix 7.2 Contact Details 7.2.1 Contact Us Please contact your local Panasonic Sales office for details on additional product options and services:
For Panasonic Sales assistance in the EU, visit https://eu.industrial.panasonic.com/about-us/contact-us Email: wireless@eu.panasonic.com For Panasonic Sales assistance in North America, visit the Panasonic Sales & Support Tool to find assistance near you at https://na.industrial.panasonic.com/distributors Please visit the Panasonic Wireless Technical Forum to submit a question at https://forum.na.industrial.panasonic.com 7.2.2 Product Information Please refer to the Panasonic Wireless Connectivity website for further information on our products and related documents:
For complete Panasonic product details in the EU, visit http://pideu.panasonic.de/products/wireless-modules.html For complete Panasonic product details in North America, visit http://www.panasonic.com/rfmodules Product Specification Rev. 1.0 Page 31
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2017-09-05 | 2402 ~ 2480 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2017-09-05
|
||||
1 | Applicant's complete, legal business name |
Panasonic Industrial Devices Europe GmbH
|
||||
1 | FCC Registration Number (FRN) |
0014980072
|
||||
1 | Physical Address |
Zeppelinstrasse 19
|
||||
1 |
Lueneburg, N/A 21337
|
|||||
1 |
Germany
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
J******@eurofins.de
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
T7V
|
||||
1 | Equipment Product Code |
1760A
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
O****** K******
|
||||
1 | Title |
Product Safety
|
||||
1 | Telephone Number |
+49-4******** Extension:
|
||||
1 | Fax Number |
+49-4********
|
||||
1 |
o******@eu.panasonic.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Panasonic Industrial Devices Europe GmbH
|
||||
1 | Name |
M**** N******
|
||||
1 | Physical Address |
Germany
|
||||
1 | Telephone Number |
+49 4********
|
||||
1 |
M******@eu.panasonic.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Bluetooth Low Energy Module | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Single Modular Approval | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Single Modular Approval. Power listed is conducted. This device is to be used for portable and mobile applications. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter product procedures. Compliance of this device in all final host configurations is the responsibility of the Grantee. OEM integrators and end-users must be provided with specific information required to satisfy RF exposure compliance, antenna installation and labeling requirements for the final host device. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Eurofins Product Service GmbH
|
||||
1 | Name |
J******** K****
|
||||
1 | Telephone Number |
49-33********
|
||||
1 | Fax Number |
49-33********
|
||||
1 |
j******@eurofins.de
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2402.00000000 | 2480.00000000 | 0.0010000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC