FCC ID: KDYOMNRCT1 OMN-RCT1 Remote Control

Wireless Receiver Module V1.1 Reference & Installation Manual TABLE OF CONTENTS INTRODUCTION ........................................................................................3 Technical Specifications ...................................................................................3 System Features ...............................................................................................3 INSTALLATION .........................................................................................4 Location ............................................................................................................4 Connections and Mounting ...............................................................................4 PROGRAMMING .......................................................................................6 How to Enter Programming Mode ....................................................................6 Wireless Transmitter Programming ..................................................................6 Viewing the Transmitter Signal Strength ..........................................................8 Viewing Unknown Serial Numbers .................................................................10 System Reset .................................................................................................10 SUPERVISION OPTIONS ........................................................................10 Check-In Supervision ......................................................................................10 Check-In Supervision Timer Settings .............................................................11 Low Battery Supervision .................................................................................12 On-Board Module Tamper Supervision Zone Assignment .............................12 PROGRAMMABLE OUTPUTS (PGMs) ..................................................13 PGM Activation ...............................................................................................13 PGM Deactivation ...........................................................................................13 REMOTE CONTROL PROGRAMMING ..................................................14 Assigning a Remote Control to the Receiver Module .....................................14 Assigning the Remote Controls to User Access Codes ..................................15 Programming the Remote Control Buttons .....................................................15 Deleting Remote Controls ...............................................................................18 Replacing the Remote Control Batteries ........................................................19 LIST OF SECTIONS ................................................................................20 1.0 INTRODUCTION The Omnia Wireless Receiver Module (OMN-RCV3) allows you to add up to 8 fully supervised Omnia wireless motion detectors and/or door contacts, and up to 8 programmable remote controls to the Spectra system. 1.1 TECHNICAL SPECIFICATIONS Di-pole antenna Error Correction Algorithm Code-Hopping Technology Frequency:

Range (line of sight):

Sensitivity:

Current consumption:

Dimensions (no antenna):

Operating temperature:

Operating humidity:

PGM outputs:

PGM output current:

Approvals:

433 MHz PIRs & door contacts = 500ft (150m) remote controls =

300ft (100m)

-120 dBm 50 mA 15cm H x 16cm L x 3cm W

(6in H x 6.5in L x 1.1in W) 0C to 50C (32F to 122F) 85%

1 relay (1 additional PGM output is available) 5A 1.2 SYSTEM FEATURES Auto-Panel Recognition Add 8 wireless motion detectors and/or door contacts to the Spectra system Add 8 remote controls to the Spectra system Reflow design On-board tamper switch Full system supervision (check-in, low battery and tamper) Transmitter signal strength indicator Omnia 3 2.0 INSTALLATION The following sections will detail how to mount and connect the Omnia Wireless Receiver Module (OMN-RCV3). 2.1 LOCATION Mount the Omnia Wireless Receiver on a wall allowing at least 5cm (2) around the module to permit adequate ventilation and heat dissipation. Select a site that is not susceptible to drastic temperature changes. Avoid installation near or in the path of strong RF fields (i.e. neon lights, computers), on or near metal objects, circuit breaker boxes, air conditioners, and heater ducts since they may cause interference and reduce the modules sensitivity. We recommend installing the module in a centralized location on the main floor. Avoid installing the module in the basement. Refer to the appropriate Spectra Reference & Installation Manual for maximum allowable distances between the control panel and the Wireless Receiver Module. 2.2 CONNECTIONS AND MOUNTING Firmly screw the antenna into the connector marked "ANT" on the Receiver Module as shown in Figure 2.1 on page 5. Using a drill or screwdriver, punch out the four mounting holes on the back of the plastic case. Align the six holes of the printed circuit board with the six pins on the back plastic mounting case and snap into place. If placed correctly, the antenna will lean directly over the groove in the mounting case. Do not cut, bend, or alter the antenna. Avoid mounting the Receiver Module near or on metal as this may affect the modules sensitivity. Do not connect more than one OMN-RCV3 module to the control panel. The OMN-RCV3 does not function with the 1758/1758EX Spectra control panel. The Omnia Wireless Receiver Module is connected to the Spectra control panel's communication bus in a star or daisy chain configuration. Refer to Figure 2.1 on page 5. 4 Reference & Installation Manual Figure 2.1: Connecting the OMN-RCV3 to the control panel Omnia 5 3.0 PROGRAMMING To successfully install an Omnia wireless system to your Spectra system, ensure that the following steps are completed:

1. Install the Omnia Receiver. Connect the Omnia Receiver to the Spectra control panel and power up. 2. Assign the remote controls if necessary. 3. Assign the transmitters (door contacts and motion detectors), and program their zones. 4. Install the transmitters. Insert the batteries, and close the transmitter cover. 5. Wait for the control panel to be in ready mode. The status light on the keypad will be green when the control panel is ready. 6. In order to ensure proper synchronization between the transmitters and receiver, open and close the transmitters covers and zones. 3.1 HOW TO ENTER PROGRAMMING MODE Programming of the OMN-RCV3 is done in Programming Mode through any keypad connected to the Spectra control panel. How to enter programming mode. 1. Press the [ENTER] button. 2. Enter your [INSTALLER CODE] (default = 000000). 3. Enter the [SECTION NUMBER] you wish to program. 4. Enter the required [DATA]. The OMN-RCV3s programming guide can be found in the appropriate Spectra Programming Guide. 3.2 WIRELESS TRANSMITTER PROGRAMMING The programming of the wireless transmitters (detectors and door contacts) is accomplished in two steps:

1. Assigning the detectors and door contacts to the Wireless Receiver Module. 2. Programming the zones in the Spectra control panel. 6 Reference & Installation Manual 3.2.1 ASSIGNING DETECTORS AND DOOR CONTACTS TO THE RECEIVER SECTIONS [601] TO [608]

In Spectra systems, up to 8 wireless transmitters (detectors and door contacts) can be assigned to each Receiver Module. Section [601] to [608]

represent expansion inputs 1 to 8 respectively. For example, section [601] is assigned to expansion input 1, section [602] is assigned to expansion input 2, etc. (refer to Table 3.1). Each Expansion Input represents a specific zone in the system depending on the type of Spectra control panel being used and whether the ATZ option is enabled (refer to the appropriate Spectra control panel Programming Guide). Table 3.1: Sections and Expansion Inputs Section #

[601]

[602]

[603]

[604]

[605]

[606]

[607]

[608]

6-digit Serial Number ___/___/___/___/___/___ ___/___/___/___/___/___ ___/___/___/___/___/___ ___/___/___/___/___/___ ___/___/___/___/___/___ ___/___/___/___/___/___ ___/___/___/___/___/___ ___/___/___/___/___/___ Expansion Input Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Input 7 Input 8 How to assign detectors & door contacts to the receiver module. In step 3 in section 3.1 on page 6:

1. Enter the desired [SECTION NUMBER] (601 to 608). 2. Enter the 6-digit serial number of the detector or door contact. Do not assign detection devices from different modules to the same expansion input. For example, do not assign a wireless transmitter to section [601], then connect a detection device to input Z1 of the APR3-ZX8. Omnia 7 The serial number is located on the inside of the transmitter or you can use the Unknown Serial Number Display method (refer to section 3.4 on page 10) to determine its serial number. The transmitters must be activated once having been assigned to the Receiver. To activate a transmitter, insert the batteries and close the cover. To ensure proper synchronization between the receiver and the transmitter, open and close the zone corresponding to the transmitter. 3.2.2 DELETING THE DETECTORS AND DOOR CONTACTS SECTIONS [601] TO [608]

How to delete the assigned transmitters. In step 3 in section 3.1 on page 6:

1. Enter the desired [SECTION NUMBER] (601 to 608). 2. Press the [FORCE] button six times to clear the serial number. 3.2.3 PROGRAMMING THE ZONES IN THE SPECTRA CONTROL PANEL The zones allocated to the wireless transmitters must be programmed in the Spectra control panel. Refer to the appropriate Spectra Reference &

Installation Manual for instructions on programming the zones. 3.3 VIEWING THE TRANSMITTER SIGNAL STRENGTH SECTIONS [631] TO [638]

Once the detectors and/or door contacts have been installed and assigned to the Receiver Module, the signal strength of each transmitter can be verified in sections

[631] to [638]. Each section represents the signal strength viewer for a specific device. For example, section [631] is the viewer for the device in section [601] and section [638] is the viewer for the device in section [608]. Please note that this feature will only work with wireless transmitters that have already been assigned to an Expansion Input (zone) as described in section 3.2.1 on page 7. A reading of 1 is the weakest and a reading of 8 is the strongest. An average reading of 3 and up is 8 Reference & Installation Manual acceptable. Sometimes moving the transmitter or receiver by a small amount will greatly increase the signal reception. How to view a transmitters signal strength. In step 3 in section 3.1 on page 6:

1. Enter the desired [SECTION NUMBER] (631 to 638). 2. Press the transmitters tamper switch, or open the corresponding zone. On an LED keypad: The keypad will illuminate numbers 1 to 8. On an LCD keypad: The keypad will display from 1 to 8 characters on the screen. For example, in the figure below the LCD screen shows a signal strength reading of 5. After entering the desired section, ignore the first reading as it will not be accurate. You can also use the OMN-RCV3s beep sequence feature to verify a transmitters signal strength. When you press a transmitters tamper switch, beep tones emanating from all the keypads connected to the communication bus will advise you of the transmitters signal strength. How to attain a transmitters signal strength using the beep sequence. 1. Press the transmitters tamper switch. 2. Listen for the beep tones:

If the signal strength is less than 3 = One beep If the signal strength is between 3 and 6 = Two beeps If the signal strength is greater than 6 = Three beeps Omnia 9 3.4 VIEWING UNKNOWN SERIAL NUMBERS SECTION [630]

This feature will display the serial number of any Omnia motion detector or door contact on any Spectra keypad. How to view unknown transmitter serial numbers. In step 3 in section 3.1 on page 6:

1. Enter section [630]. 2. Press the tamper switch of any Omnia wireless motion detector or door contact. When the signal has been received, the keypad will emit a confirmation beep (Beep-Beep-Beep-Beep-Beep). 3. On an LED Keypad: The serial number digits will appear one at a time by illuminating the corresponding LED light. To view the next digit press the

[ENTER] button. On an LCD Keypad: The first 3 digits of the serial number will appear. Press the [ENTER] button 3 times to view the next 3 digits. 3.5 SYSTEM RESET Refer to the appropriate Spectra Reference and Installation Manual. 4.0 SUPERVISION OPTIONS 4.1 CHECK-IN SUPERVISION SECTION [610]: OPTION [1]

Option [1] enables the Check-in Supervision feature. The Wireless Receiver Module waits for each of its assigned detectors and/or door contacts to send a status signal within a specified time period (as programmed in section 4.2) to confirm their presence and functionality. If a device has not sent a signal within that time period, the Wireless Receiver Module will transmit a supervision loss signal to the control panel. The control panel can then generate a trouble, an alarm, and/or can transmit 10 Reference & Installation Manual a report code to the monitoring station. For details refer to the appropriate Spectra Reference & Installation Manual. How to enable check-in supervision. In step 3 in section 3.1 on page 6:

1. Enter section [610]. 2. Enable or disable option [1]. Option [1] OFF = Check-In Supervision disabled (default) Option [1] ON = Check-In Supervision enabled 4.2 CHECK-IN SUPERVISION TIMER SETTINGS SECTION [610]: OPTIONS [2] AND [5]

Options [2] and [5] define the time period that must elapse before the Omnia transmitters send a status signal to the Wireless Receiver Module. For example, if the timer is set to 12 min (option [5]=off ; option [2]=on), the transmitters will send a status signal every 12 minutes to the Receiver Module. If the OMN-RCV3 does not receive a signal from one of its wireless transmitters within the period defined here, it can send a Supervision Loss signal to the control panel. Refer to section 4.1 for instructions on enabling check-in supervision. How to set the check-in supervision timer. In step 3 in section 3.1 on page 6:

1. Enter section [610]. 2. Enable or disable options [2] & [5]. Option [2] OFF = hours (default) Option [2] ON = minutes Option [5] OFF = 12 (default) Option [5] ON = 6 The assigned transmitters must be set to the same Check-In timer setting as the Receiver. For example, if the Receiver Check-In timer is set at 12 hours, the transmitters Check-In timers must also be 12 hours. Omnia 11 4.3 LOW BATTERY SUPERVISION When the battery voltage of an Omnia wireless transmitter (motion detector or door contact) drops to less than 3.1V, the Spectra control panel will send a low battery report code to the monitoring station, and a trouble will appear in the keypads trouble display. 4.4 ON-BOARD MODULE TAMPER SUPERVISION ZONE ASSIGNMENT SECTION [615]:

The OMN-RCV3 comes equipped with an on-board tamper switch. This feature will allow a module tamper to report through one of the modules Expansion Inputs

(zone). When a tamper is detected on the module, it will send a Zone Tamper report code to the control panel via the communication bus. The Zone Tamper report code will originate from the zone defined by the Expansion Input (001-008) you have programmed in section [615]. Please note that the corresponding zone must be programmed (refer to the appropriate Spectra Reference & Installation Manual for more details). For example, when you program 003 (Expansion Input 3) in section [615] of a Spectra 1728 panel with the ATZ feature enabled, and a tamper occurs on the OMN-

RCV3 module, the control panel will transmit the Zone Tamper report code as originating from zone 15. If you Enable the OMN-RCV3s tamper switch in section [615], the tamper switch will occupy one of the zones. How to assign the Receivers tamper switch to a zone. In step 3 in section 3.1 on page 6:

1. Enter section [615]. 2. Enter an [INPUT NUMBER] (001-008). 000=Disabled (default) 12 Reference & Installation Manual 5.0 PROGRAMMABLE OUTPUTS (PGMs) 5.1 PGM ACTIVATION The Omnia Wireless Receiver Module comes equipped with one on-board 5A PGM relay output (programmable output). A second 5A PGM output is available as an option. PGM1 and PGM2 are always enabled and are activated only through the Omnia Remote Control (OMN-RCT1). Remote control button 1 (C) controls PGM1, and button 2 (D) controls PGM2 (refer to Figure 6.4 on page 18 for button locations). Press the appropriate remote control button to activate the corresponding PGM. If the PGM deactivation mode is set at Manually (refer to section 5.2), the button used to activate the PGM will also be used to deactivate the PGM. 5.2 PGM DEACTIVATION SECTION [610] : OPTIONS [6] AND [7]

Once a PGM has been activated (refer to section 5.1), options [6] and [7] determine how the respective PGM will deactivate. If the option is OFF, the activated PGM will automatically deactivate after 2 seconds. If the option is ON, the activated PGM can only be deactivated by pressing the appropriate button on the Omnia Remote Control (refer to section 5.1). How to set the PGM deactivation mode. In step 3 in section 3.1 on page 6:

1. Enter section [610]. 2. Enable or disable options [6] and [7]. Option [6] OFF = PGM1: 2 second timer (default) Option [6] ON = PGM1: Manually Option [7] OFF = PGM2: 2 second timer (default) Option [7] ON = PGM2: Manually Omnia 13 6.0 REMOTE CONTROL PROGRAMMING The Omnia Wireless Receiver Module accepts up to eight fully programmable remote controls. Programming the remote controls is accomplished in three steps:

1. The remote controls must be assigned to the Wireless Receiver Module. 2. The remote controls from the Wireless Receiver Module must be assigned to User Access Codes. 3. The buttons on the remote controls must be programmed. In Spectra systems, sections [721]/[731] to [728]/[738], [701] to [708], and [711] to

[718] are all interrelated. For example, when assigning a remote control to the Receiver Module:

1. The remote control is assigned using the Automatic Learning method in sections

[721]/[731] to [728]/[738]. 2. The remote control is assigned to User Access Codes in sections [701] to [708]. 3. The remote controls buttons are programmed in sections [711] to [718]. The remote control will transmit a signal for only 1 second when a button is pressed. This is done to conserve the remote controls batteries. 6.1 ASSIGNING A REMOTE CONTROL TO THE RECEIVER MODULE SECTIONS [721] / [731] TO [728] / [738]

Remote controls are assigned to the module using the Automatic Learning method. Depending on which Spectra system version you are using, the automatic learning method differs. For installations using a Spectra control panel version 1.23 or lower:

How to assign a remote control to the receiver module (V1.23 and lower). In step 3 in section 3.1 on page 6:

1. Enter the desired [SECTION NUMBER] (721 to 728). 2. Enter [111111]. A rejection beep will sound, and it will exit the section. 3. Press any button on the remote control twice, or until you hear three consecutive rejection beeps (Beeeeeeeeeeeeeeep). 14 Reference & Installation Manual For installations using a Spectra control panel version 2.0 or higher:

How to assign a remote control to the receiver module (V2.0 and higher). In step 3 in section 3.1 on page 6:

1. Enter desired [SECTION NUMBER] (731 to 738). 2. Press any button on the remote control twice, or until the confirmation beep sounds (Beep-Beep-Beep-Beep-Beep). If you are having trouble assigning the remote control, the environment may be too noisy. Therefore, we recommend that you assign the remote controls before installing the detectors and door contacts. 6.2 ASSIGNING THE REMOTE CONTROLS TO USER ACCESS CODES SECTIONS [701] TO [708]:

Each remote control must be assigned to a User Access Code. All User Access Codes are given a User Number from 001 to 048. Enter the desired User Number in a section from [701] to [708] that represent the remote control assigned in sections [721]/[731] to

[728]/[738] (refer to section 6.1 on page 14). For example, the remote control assigned in section [731] will be assigned to the User Access Code designated in section [701]. How to assign a remote control to a user access code. In step 3 in section 3.1 on page 6:

1. Enter the desired [SECTION NUMBER] (701 to 708). 2. Enter the User Number to be assigned to the remote control (001 to 048). 6.3 PROGRAMMING THE REMOTE CONTROL BUTTONS SECTIONS [711] TO [718]

Each remote control can be programmed to send a signal to the control panel to perform up to 8 different actions. Each digit in sections [711] to [718] represents a button or combination of buttons (refer to Table 6.1 on page 16). When a user arms or disarms using the remote control, the control panel will arm or disarm all the areas assigned to the User Access Code. For example, you arm with a remote control whose User Access Code is assigned to areas 1 and 2, the control panel will attempt to arm areas 1 and 2. Omnia 15 Sections [711] to [718] represent the remote controls assigned to sections [721]/

[731] to [728]/[738] (refer to section 6.1 on page 14). For example, the buttons for the remote control assigned in section [731] will be programmed in section [711]. How to program the remote control buttons:

In step 3 in section 3.1 on page 6:

1. Enter the desired [SECTION NUMBER] (711 to 718). 2. Enter the hexadecimal value (0 to D) of the desired options from Table 6.2 on page 17 in the appropriate space (refer to Table 6.1 on page 16). If you do not wish to program all the buttons or button combinations, simply press the

[ENTER] button at any time to save and exit. Note: To delete the hexadecimal values in a particular section (711-718), press the [FORCE] button once for every value. Table 6.1: Remote Control Button Programming Remote Control Button Programming (refer to Table 6.2) ____/____/____/____/____/____/____/____ A B C D A+B C+D A+C B+D ____/____/____/____/____/____/____/____ A B C D A+B C+D A+C B+D ____/____/____/____/____/____/____/____ A B C D A+B C+D A+C B+D ____/____/____/____/____/____/____/____ A B C D A+B C+D A+C B+D ____/____/____/____/____/____/____/____ A B C D A+B C+D A+C B+D ____/____/____/____/____/____/____/____ A B C D A+B C+D A+C B+D ____/____/____/____/____/____/____/____ A B C D A+B C+D A+C B+D ____/____/____/____/____/____/____/____ A B C D A+B C+D A+C B+D remote control #1 remote control #2 remote control #3 remote control #4 remote control #5 remote control #6 remote control #7 remote control #8 Section

[711]

[712]

[713]

[714]

[715]

[716]

[717]

[718]

16 Reference & Installation Manual Table 6.2: Button Options

[FORCE] = Button Disabled

[1] = Regular Arm

[2] = Stay Arm

[3] = Instant Arm

[4] = Force Arm

[5] = Disarm

[6] = Disarm when there is no alarm

[7] = Regular Arm and Disarm

[8] = Generate a Panic 1 Alarm (Police)

[9] = Generate a Panic 2 Alarm (Medical)

[A] = Generate a Panic 3 Alarm (Fire)

[B] = Activates any PGMs that have Event Group

#07 as their Activation Event

[C] = Activates any PGMs that have Event Group

#08 as their Activation Event

[D] = Activates any PGMs that have Event Group

#09 as their Activation Event Table 6.3: Decimal & Hexadecimal Programming Table Value or Action What Do I Press?

What Do I See?

10-Zone LED 16-Zone LED

[1] to [9]

[10]

[11]

[12]

[13]

[14]

[15]

LCD

[1] to [9]

0 B C D E F

[1] to [9]

[0]

[STAY]

[BYP]

[MEM]

[TBL] / [TRBL]

[PG] / [FNC1]

[CLEAR]

[1] to [9]

[0 (10)]

[STAY]

[BYP]

[MEM]

[TBL]

[PG]

[ENTER]

flashes Values 1 to 9 A (hexa only) B (hexa only) C (hexa only) D (hexa only) E (hexa only) F (hexa only) Exit Without Saving Insert Blank Digit Save Data

[ARM1] &

[STAY1] flash SECTION [ ]

[FORCE]

Displays next digit or next section

[ENTER]

Advances to the next section Omnia 17 Figure 6.4: Remote Control Button Identification The User Code assigned to the remote control (refer to section 6.2 on page 15) must have the same User Options enabled. For example, if you enable the Force Arming button option, you must enable the appropriate Force Arming user option. Also, if you enable any Panic button options, you must enable the Panic options in the Spectra control panel (refer to the appropriate Spectra Reference & Installation Manual). 6.4 DELETING REMOTE CONTROLS SECTIONS [721]/[731] TO [728]/[738]

For installations using a Spectra control panel version 1.23 or lower:

How to delete a remote control (Spectra version 1.23 or lower):

In step 3 in section 3.1 on page 6:

1. Enter the desired [SECTION NUMBER] (721 to 728). 2. Enter [000000]. 18 Reference & Installation Manual For installations using a Spectra control panel version 2.0 or higher:

How to delete a remote control (Spectra version 2.0 or higher):

In step 3 in section 3.1 on page 6:

1. Enter the desired [SECTION NUMBER] (731 to 738). 2. Press the [FORCE] button. 6.5 REPLACING THE REMOTE CONTROL BATTERIES How to replace the remote control batteries. 1. Remove the two screws from the back of the remote control and remove the back cover. 2. Remove the old batteries from inside the remote control. 3. Replace with two 3V lithium batteries (CR2016) ensuring proper polarity. The positive of the batteries is inserted face down. 4. Set the back cover in place, and fasten it with the two screws. Omnia 19 7.0 LIST OF SECTIONS Section

[601] to [608]

[610]

[615]

[630]

Description

- Assign detectors and door contacts to the receiver

- Delete the detectors and door contacts Option [1]: Check-in supervision Option [2]: Check-in supervision base time Option [5]: Check-in supervision time value Option [6]: PGM1 deactivation mode Option [7]: PGM2 deactivation mode On-board module tamper supervision zone assignment View unknown serial numbers

[631] to [638] View the detector and door contact signal strengths

[701] to [708] Assign the remote controls to user access codes

[711] to [718]

[721] to [728]

[731] to [738]

Programming the remote control buttons

- Assign a remote control to the receiver For Spectra versions 1.23 or lower For Spectra versions 2.0 or higher

- Delete a remote control 20 Reference & Installation Manual WARRANTY The Seller warrants its products to be free from defects in materials and workmanship under normal use for a period of one year. Except as specifically stated herein, all express or implied warranties whatsoever, statutory or otherwise, including without limitation, any implied warranty of merchantability and fitness for a particular purpose, are expressly excluded. Because Seller does not install or connect the products and because the products may be used in conjunction with products not manufactured by Seller, Seller cannot guarantee the performance of the security system. Seller obligation and liability under this warranty is expressly limited to repairing or replacing, at Seller's option, any product not meeting the specifications. In no event shall the Seller be liable to the buyer or any other person for any loss or damages whether direct or indirect or consequential or incidental, including without limitation, any damages for lost profits, stolen goods or claims by any other party caused by defective goods or otherwise arising from the improper, incorrect or otherwise faulty installation or use of the merchandise sold. Omnia 21 NOTES