| all | frequencies |
|
|
|
|
exhibits | applications |
|---|---|---|---|---|---|---|---|
| manual | photos | label | |||||
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
Users Manual | Users Manual | 2.13 MiB | December 21 2021 | |||
| 1 |
|
Internal Photos | Internal Photos | 345.12 KiB | December 21 2021 / June 20 2022 | delayed release | ||
| 1 |
|
External Photos | External Photos | 68.57 KiB | December 21 2021 | |||
| 1 |
|
ID Label/Location Info | ID Label/Location Info | 106.59 KiB | December 21 2021 | |||
| 1 |
|
Confidentiality | Cover Letter(s) | 111.54 KiB | December 21 2021 | |||
| 1 |
|
Declaration of authorization | Cover Letter(s) | 105.10 KiB | December 21 2021 | |||
| 1 |
|
Test Report | Test Report | 1.62 MiB | December 21 2021 | |||
| 1 |
|
Test Setup Photos | Test Setup Photos | 240.89 KiB | December 21 2021 |
| 1 | Users Manual | Users Manual | 2.13 MiB | December 21 2021 |
MG5000+ / MG5050+
Installation Guide 32-Zone Wireless Security Systems DRAFT Table of Contents Introduction ....................................................................... 5 Features ...................................................................................................................................5 MG5050+ Requirements ...................................................................................................5 System Overview .................................................................................................................5 Modules Current Consumption List .............................................................................5 Specifications ........................................................................................................................6 Installation ..........................................................................7 Location and Mounting .....................................................................................................7 EN 50131 Compliancy ........................................................................................................7 Earth Ground .........................................................................................................................7 AC Power .................................................................................................................................7 Backup Battery ......................................................................................................................7 MG5000+ PCB Layout .........................................................................................................8 MG5050+ PCB Layout .........................................................................................................9 PCB Metal Box Installation ............................................................................................. 10 Auxiliary Power Terminals ............................................................................................. 11 Telephone Line Connection .......................................................................................... 11 Alarm Transmissions ........................................................................................................ 11 Bell Output Connection .................................................................................................. 11 Programmable Output Connections ......................................................................... 11 Single Zone Inputs ........................................................................................................... 12 Advanced Technology Zone (ATZ) Connections .................................................. 13 Fire Circuits .......................................................................................................................... 14 Programming Methods ....................................................15 BabyWare Software for Windows ............................................................................... 15 Programming Using a Keypad ..................................................................................... 15 Configuring the Keypad Zone Number .................................................................... 16 LCD Keypad Labels ...........................................................17 Input Keys ............................................................................................................................ 17 Label Sections .................................................................................................................... 17 Special Characters and Keypad Letter Assignment .............................................. 17 Access Codes .....................................................................20 Access Code Length ......................................................................................................... 20 Installer Code (Default: 0000 / 000000) ..................................................................... 20 Maintenance Code (Default: Empty) .......................................................................... 20 System Master Code (Default: 1234 / 123456) ....................................................... 20 User Code Options ........................................................................................................... 20 Lock Master Code ............................................................................................................. 21 StayD Mode .......................................................................22 Overview .............................................................................................................................. 22 Entry/Exit Paths .................................................................................................................. 22 Entry/Exit with a Keypad ................................................................................................ 22 Entry/Exit with a Remote Control ............................................................................... 22 Window Mode and Re-arm Delay ............................................................................... 22 Advanced Settings ........................................................................................................... 22 Zone Programming ..........................................................23 Zone Definitions ................................................................................................................ 23 Zone Definition Status .................................................................................................... 26 Zone Partition Assignment ........................................................................................... 26 Zone Options ...................................................................................................................... 26 EOL Zones ............................................................................................................................ 28 ATZ Zone Doubling .......................................................................................................... 28 Tamper Input on ZX8/ZX82 ID A (Panel + 1) ........................................................... 28 Tamper Input on ZX8/ZX82 ID B (Panel + 9) ........................................................... 28 Tamper Input on ZX8/ZX82 ID C (Panel + 17) ........................................................ 28 ATZ Wiring Options .......................................................................................................... 28 Zone Input 1 Becomes a 2-wire Smoke Input ........................................................ 28 Zone Timers ........................................................................................................................ 28 Keyswitch Programming ................................................................................................ 29 Keyswitch Numbering ..................................................................................................... 29 Keyswitch Definitions ...................................................................................................... 29 Keyswitch Options ............................................................................................................ 29 Wireless Features .............................................................30 Supervision Options ........................................................................................................ 30 RF Jamming Supervision ................................................................................................ 30 Remote Control Programming .................................................................................... 30 Arming and Disarming Options ......................................32 Switch to Stay Arming if no Entry Delay is opened .............................................. 32 When Delay Zone is bypassed Follow Zones become Entry Delay 2 ............ 32 Regular Arming switches to Force Arming ............................................................. 32 Stay Arming switches to Stay Force Arming ........................................................... 32 Sleep Arming switches to Sleep Force Arming ...................................................... 32 Restrict Arming on Battery Failure ............................................................................. 32 Restrict Arming on Tamper Failure ............................................................................ 32 Restrict Arming on Wireless Supervision Trouble ................................................. 33 Arm/Disarm with VDMP3 ............................................................................................... 33 Timed Auto-Arming ......................................................................................................... 33 No Movement Auto-Arming ......................................................................................... 33 Auto-Arming Options ..................................................................................................... 33 One-Touch Arming .......................................................................................................... 34 One-Touch Bypass Programming ............................................................................... 34 Exit Delay ............................................................................................................................. 34 Bell Squawk On Arm/Disarm with Keypad .............................................................. 34 Bell Squawk On Arm/Disarm with Remote Control ............................................. 34 No Exit Delay When Arming with Remote Control .............................................. 34 No Exit Delay Beeps and No Bell Squawk When Stay/Sleep Arming ............. 34 Exit Delay Termination ................................................................................................... 34 Fast Exit ................................................................................................................................ 34 Alarm Options ..................................................................35 Bell Cut-Off Timer ............................................................................................................. 35 Recycle Alarm ..................................................................................................................... 35 Tamper Recognition ........................................................................................................ 35 RF Module Supervision ................................................................................................... 35 Tamper Bypass Options ................................................................................................. 35 Tamper Supervision on the Bus Module .................................................................. 35 Tamper Supervision on Panel ...................................................................................... 36 Keypad Panic Options ..................................................................................................... 36 Panic Lockout Timer ........................................................................................................ 36 Flex-Instant Delay ............................................................................................................. 36 Reporting and Dialer settings .........................................37 Zone Reporting Codes .................................................................................................... 37 User Reporting Codes ..................................................................................................... 37 Special Arming Report Codes ...................................................................................... 37 Special Disarming Report Codes ................................................................................. 37 Special Alarm Report Codes ......................................................................................... 37 System Trouble Report Codes ..................................................................................... 38 System Trouble Restore Report Codes ..................................................................... 38 System Special Report Codes ....................................................................................... 38 Clear Reporting Codes .................................................................................................... 39 Reset Reporting Codes ................................................................................................... 39 Monitoring Station Telephone Numbers ................................................................. 39 Personal Dialing Numbers ............................................................................................. 39 Reporting Formats ........................................................................................................... 40 Dialing Method .................................................................................................................. 41 Pulse Ratio ........................................................................................................................... 41 Maximum Dialing Attempts ......................................................................................... 41 Maximum Dialing Attempts - VDMP3 ....................................................................... 41 Delay Between Dialing Attempts ................................................................................ 41 Switch to Pulse on 5th Attempt .................................................................................. 41 Alternate Dial Option ...................................................................................................... 41 Force Dial Option .............................................................................................................. 41 Recent Closing Delay ....................................................................................................... 42 Auto Test Report ............................................................................................................... 42 Closing Delinquency Delay ........................................................................................... 42 Power Failure Report Delay .......................................................................................... 42 Report System Disarming .............................................................................................. 42 Zone Restore Report Options ....................................................................................... 43 Telephone Line Monitoring (TLM) .............................................................................. 43 Pager Reporting Delay .................................................................................................... 43 Pager Reporting Message Repetition ........................................................................ 43 Personal Reporting Delay .............................................................................................. 43 Personal Reporting Message Repetition .................................................................. 43 Disable Reporting ............................................................................................................. 43 Programmable Outputs ...................................................44 PGM Activation Event ..................................................................................................... 44 PGM Deactivation Event .................................................................................................44 PGM Delay ............................................................................................................................44 PGM Options .......................................................................................................................44 PGM Programming ...........................................................................................................45 System Settings ............................................................... 46 Version Number Display .................................................................................................46 Push Button Power Reset ...............................................................................................46 Installer Lock .......................................................................................................................46 Keypad Lockout Feature .................................................................................................46 Partitioning ..........................................................................................................................46 Confidential Mode ............................................................................................................46 Installer Function Keys .....................................................................................................46 Daylight Savings Time .....................................................................................................47 Customized Daylight Saving Programming ............................................................47 Audible Trouble Warning Except AC Failure ...........................................................47 Audible Trouble Warning on AC Failure ...................................................................47 Display Entry Delay on LCD keypad (K32LCD+) .....................................................47 Display Exit Delay on LCD keypad (K32LCD+) ........................................................48 Settings for BabyWare Software .................................... 49 Panel Answer Options .....................................................................................................49 Panel Identifier ...................................................................................................................49 PC Password ........................................................................................................................49 PC Telephone Number ....................................................................................................49 Call BabyWare Software ..................................................................................................49 Answer BabyWare Software ..........................................................................................49 Automatic Event Buffer Transmission ........................................................................50 Call Back BabyWare ...........................................................................................................50 Connecting to BabyWare ................................................................................................50 User Operation ................................................................. 51 Alarm Display ......................................................................................................................51 Trouble Display ..................................................................................................................51 Index ................................................................................. 52 Important Installation Considerations:
Maximum Peak to peak ripple voltage on AUX is 500 millivolts. Low voltage on the battery generated when battery is below 10.7 volts Deep discharge protection on the battery operates 7.7 0.3 volts. If output voltage drops below 11.3 volts a fault is signal is generated. UL and ULC Warnings This equipment has the capability of being programmed with features not verified for use in UL installations. To stay within UL and ULC standards, the installer should use the following guidelines when configuring the system:
All components of the system should be UL listed for the intended application. If used for fire detection, the installer should refer to NFPA Standards #72, Chapter 2. In addition, once installation is complete, the local fire authority must be notified of the installation. WARNING: This equipment must be installed and maintained by qualified service personnel only This equipment must be verified by a qualified technician once every three years. All keypads must use an anti-tamper switch. Do not bypass fire zones. Maximum allowed entry delay is 45 seconds. Maximum allowed exit delay is 60 seconds. Minimum 4 minutes for bell cut-off time. The following features do not comply with UL requirements: Bypass Recall and Auto Trouble Shutdown. Do not connect the primary indicating device to a relay. The installer must use the bell output. To comply with UL985, the auxiliary power output should not exceed 200mA. Do not connect the zone ground terminal with UL Listed products. The metallic enclosure must be grounded to the cold water pipe. All outputs are Class 2 or power-limited, except for the battery terminal. The Class 2 and power-limited fire alarm circuits shall be installed using CL3, CL3R, CL3P, or substitute cable permitted by the National Electrical Code, ANSI/NFPA 70. EOL resistor part #2011002000 For UL Installations: Universal UB1640W 16.5VAC min 40VA All outputs are rated from 11.3 Vdc to 13.5 Vdc 12 Vdc 4 Ah rechargeable acid/lead or gel cell backup battery (YUASA model #NP7-12 recommended) for residential use. Use a 7 Ah battery to comply with fire requirements. Wheelock 46T-12 siren Paradox, STAY- D Magellan, Spectra, and BabyWare are trademarks or registered trademarks of Paradox Security Systems (Bahamas) Ltd. or its affiliates. Patents 2008/10193, 2292187, 2648482, 7965171 RE#39406 ZL200780016140.6 apply together with other. Canadian and international patents may apply. Other patents may be pending. All rights reserved. Specifications may change without prior notice. 2020 Paradox Security Systems (Bahamas) Ltd. FCC and Industry Canada Compliance Statement This device complies with FCC Rules Part 15 and with Industry Canada license exempt RSS standard(s). Operation is subject to two conditions:
This device may not cause harmful interference. This device must accept any interference that may be received or that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
L'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. Warranty For complete warranty information on this product please refer to the Limited Warranty Statement found on our Web site: www.paradox.com/terms. Your use of this Paradox product signifies your acceptance of all warranty terms and conditions. FCC ID: KDYMG5050PLUS IC: 2438A-MG5050PLUS Limitations of Alarm Systems It must be understood that while your Paradox alarm system is highly advanced and secure, it does not offer any guaranteed protection against burglary, fire or other emergency (fire and emergency options are only available on certain Paradox models). This is due to a number of reasons, including by not limited to inadequate or improper installation/
positioning, sensor limitations, battery performance, wireless signal interruption, inadequate maintenance or the potential for the system or telephone lines to be compromised or circumvented. As a result, Paradox does not represent that the alarm system will prevent personal injury or property damage, or in all cases provide adequate warning or protection. Your security system should therefore be considered as one of many tools available to reduce risk and/or damage of burglary, fire or other emergencies, such other tools include but are not limited to insurance coverage, fire prevention and extinguish devices, and sprinkler systems. We also strongly recommend that you regularly maintain your security systems and stay aware of new and improved Paradox products and developments. TBR-21: In order to comply with TBR-21, standard force dialing must be enabled. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance (Paradox Security Systems Ltd.) could void the users authority to operate the equipment. MG5000+ / MG5050+ Installation Guide Introduction Features 32 zones (any of which can be wireless or keypad zones) 32 users and 32 remote controls (one per user) In-field upgradeable Menu-driven programming for the Installer, Master, and Maintenance codes. This enables you to program the panel through a simple and easy to use interface, without the use of section numbers Multiple telephone numbers for event reporting: Three for the monitoring station, five for personal dialing Calendar with daylight savings time Sleep arming method: Similar to Stay arming, Sleep arming allows users to remain in a protected area, but provides a higher level of protection Connect up to 15 hardwired keypads on the 4-wire communication bus Push button power reset Available in 433MHz or 868MHz RF jamming supervision (section [700], option [5]): The control panel will report a trouble if the RF signal is being jammed Supports SIA reporting format to central station (V4.86 and lower) MG5050+ Requirements PCS265 LTE V4.37 and higher IP150+ V5.45 and higher System Overview Module K10V/H, K32+,K32LCD+, K32LX, K35, K636, TM50, TM70 ZX8, ZX8SP, ZX82 RPT1 VDMP3 IP150+
PCS250/PCS250G, PCS265LTE RX1 PGM4 PGM82 HUB2 PS25/PS45 HD78F/HD88 Modules Current Consumption List Module K10V/H K32+
K32LCD+
K32LX K35 K636 TM50 TM70 ZX8 ZX8SP Current Consumption Min. = 44 mA / Max. = 72 mA Min. = 49 mA / Max. = 148 mA Min. = 43 mA / Max. = 86 mA 120 mA Min. = 30 mA / Max. = 70 mA Min. = 15 mA / Max. = 30 mA 150 mA max + 80 mA sounder 250 mA max + 80 mA sounder Min. = 29 mA / Max. = 31 mA 28 mA ZX82 95 mA max (all LED on) HD78F 350 mA - IR illumination ON 250 mA - IR illumination OFF 100 mA - System lost AC / Battery operation Maximum number per system 15 total including ZX8 / ZX82 Description 10 and 32-Zone Hardwired LED and LCD Keypad Module, Touchscreen 8-Zone Expansion Module Magellan Wireless Repeater Module Plug-In Voice Dialer IP Internet Module Communicator Module Wireless Receiver Module 4-Output Expansion Module 8-Output Expansion Module 2-Port HUB and Bus Isolator Power supply IP Camera / Detector 3 2 1 1 1 1 1 1 1 1 15 Module RPT1 VDMP3 IP150+
PCS250 PCS250G PCS265LTE RX1 PGM4 PGM82 HUB2 HD88 Current Consumption 65 mA Min. = 28 mA / Max. = 28 mA 100 mA Standby:100 mA / Alarm: 450 mA Standby:100 mA / Alarm: 450 mA Standby: 60 mA / Max. = 300 mA 25 mA Min. = 13 mA / Max. = 150 mA 315 mA (all PGMs activated) Min. = 24 mA / Max. = 50 mA 350 mA - IR illumination ON 250 mA - IR illumination OFF 100 mA - System lost AC / Battery operation 5 MG5000+ / MG5050+ Installation Guide Specifications MG5000+ / MG5050+
Power rating Power consumption Aux. power *
Battery Battery charging current On-board zones Bell output **
On-board PGMs Dimensions Weight Operating temperature Humidity Standards
* Cannot exceed 200 mA for UL installations
** Cannot exceed 1A for UL installations 16.5 VAC (50 or 60Hz) minimum 20 VA (40 VA recommended) MG5000+: 1.2A(Max.), 85 mA (Idle) MG5050+: 1.2A(Max.), 95 mA (Idle) 0.7A typical, 0.8A maximum, active shutdown at 1.1A 12 VDC, 4 Ah/7Ah 500 mA MG5000+: 2 MG5050+: 5 1A (fuseless shutdown at 3A) MG5000+: 2 MG5050+: 4 (1+/- trigger) All on-board PGMS are 100 mA low-current outputs MG5000+: 14 x 10.4 cm (5.5 x 4.1 in.) MG5050+: 19 x 10.2 cm (7.5 x 4 in.) 18g 0C to 50C (32F to 122F) 5% - 90%
TBD All control panel outputs are rated to operate between 10.8Vdc and 12.1 Vdc 30 hrs backup 60 hrs backup Recharge to 80% (@350 mA) 7 AHr 150 mA 50 mA 20 hrs. 6 MG5000+ / MG5050+ Installation Guide Installation Location and Mounting Before mounting the metal box, push the five white nylon mounting studs into the back of the box. Pull all cables into the cabinet and prepare them for connection before mounting the circuit board into the back of the cabinet. Select a centralized installation site on the main floor that isn't easily accessible to intruders and leave at least 5 cm (2 in.) around the panel box to permit adequate ventilation and heat dissipation. The installation site should be dry and close to an AC source, ground connection and telephone line connection. Avoid installation near or in the path of strong RF fields (e.g., neon lights, computers), on or near metal objects, circuit breaker boxes, air conditioners and heater ducts since they may cause interference and reduce sensitivity. Avoid installing the control panel in the basement. IMPORTANT: To comply to EN 50131 requirements, unit must be installed in an approved tamper enclosure. Do not cut, bend or alter the antennas and ensure that electrical wires do not cross over the antennae as these may affect the signal reception. EN 50131 Compliancy In order to meet with EN 50131 compliancy you will require the following:
EN Metal Box Tamper Kit TK278 Tamper Antenna Firmware version 4.96 or higher Earth Ground Connect the zone and dialer ground terminals from the control panel to the metallic enclosure and cold water pipe or grounding rod as per local electrical codes. WARNING: For maximum lightning protection, use separate earth grounds for the zone and dialer grounds as shown in the PCB Layouts for each respective panel. For UL installations, the metallic enclosure must be grounded to the cold water pipe. AC Power Do not use any switch-controlled outlets to power the transformer in order to avoid accidental user AC shut off. Connect the transformer as shown in Figure 1. Use the below table for appropriate transformer. Use only a safety approved transformer with rated output voltage of 16.5 Vac and rated power of 40 VA (maximum). Transformer:
(use only one of the following) Panel DC power supply output rated at:
Maximum allowed current supplied by all Auxiliary outputs:
Battery Charge Currents 16 VAC 20 VA
(not verified by UL) 1.1A Max: 700 mA 350 mA For UL 16.5 VAC 40 VA 1.5A Max: 700 mA Do not exceed 200 mA for US or Canadian installations 350 mA/700 mA (programmable via panel) Backup Battery To provide power during a power loss, connect a 12 Vdc 4 Ah rechargeable acid/lead or gel cell backup battery as shown in Figure 1 below. Use a 7 Ah battery to comply with UL fire requirements. Connect the backup battery after applying AC power. When installing, verify proper polarity as reversed connections will blow the battery fuse. Use only safety approved rechargeable battery with rated voltage of 12 Vdc and rated current of 7A maximum. Battery Test If the battery is disconnected or if the battery fuse is blown, a No/Low Battery failure will appear in the keypads trouble display (see Trouble Display on page 51). This trouble will also appear if the batterys capacity is too low or if the voltage drops to 10.5V or lower while the control panel is running on the backup battery. At 8.5V or lower, the panel shuts down and all outputs close. UL Warning:
A 12 Vdc / 7 AH battery is required to comply with UL fire requirements. Rechargeable Battery 12 Vdc / 4 Ah or 7Ah Figure 1: AC Power and Backup Battery Connections Caution:
Disconnect battery before replacing the fuse. WARNING: Improper connection of the transformer may result in damage to the system. 7 MG5000+ PCB Layout MG5000+ / MG5050+ Installation Guide Do not cut, bend, or alter the antenna, and ensure that electrical wires or other type of wires do not cross over it, as this may affect signal reception. Do not install the antenna near wires as it may cause interference. To provide maximum lightning protection we strongly recommend having separate earth connections for the dialer and zone ground terminals. Disconnect telephone line before servicing. 1 Four-pin connector can be used for quick installation of a keypad 2 LEDs ON = AC present; OFF = AC missing ON = Battery present; OFF = No battery Flashing once per second = Normal operation ON = Aux present; OFF = Aux off FLASH ON = RF message reception AC LED:
Battery LED:
STAT LED:
AUX LED:
RF-RX LED:
RF-TX LED:
FLASH ON = RF transmission from panel 3 Panel reset 4 Serial: Used for connecting the IP Internet Module/PCS (Data); also used for In-Field Firmware upgrade through a 307USB Direct Connect Interface 5 Antenna 6 RS485 connector 7 Zone Input 8 PGMs: these jumpers allows you to choose whether the solid state relay PGMs are grounded (-), or give out 12V (+). 9 Backup Battery connections 10 The BELL output will shutdown if the current exceeds 3A 11 AWG #14 single conductor solid copper wire 12 Ground clamp 13 Cold water pipe grounding 14 To ground 15 Keypad zone configuration 16 Zone connection, if EOL is enabled, see section [706] option 2, on page page 28 17 To connect additional wiring to auxiliary power, use the red (+) and black
(-) keypad connectors; auxiliary power will shut down if current exceeds 3A; if the auxiliary output is overloaded and shuts down, you must disconnect all loads from the output for at least 10 sec. before reconnecting any load back to the auxiliary output The sum of the current drawn from the BELL and AUX must be limited to 1.3A. Exceeding this limit will overload the panel power supply and lead to complete system shutdown. 40 VA transformer strongly recommended. This equipment must be installed and maintained by qualified service personnel only. Max. number of keypads: 15 keypads Max. aux. current: 700 mA Max. distance of bus module from panel: 76 m (250 ft.) Max. total run of wire: 230 m (750 ft.) 8 MG5000+ / MG5050+ Installation Guide MG5050+ PCB Layout Do not cut, bend, or alter the antenna, and ensure that electrical wires or other type of wires do not cross over it, as this may affect signal reception. Do not install the antenna near wires as it may cause interference. To provide maximum lightning protection we strongly recommend having separate earth connections for the dialer and zone ground terminals. Disconnect telephone line before servicing. 1 Four-pin connector can be used for quick installation of a keypad 2 LEDs ON = AC present; OFF = AC missing ON = Battery present; OFF = No battery Flashing once per second = Normal operation ON = Aux present; OFF = Aux off FLASH ON = RF message reception AC LED:
Battery LED:
STAT LED:
AUX LED:
RF-RX LED:
RF-TX LED:
FLASH ON = RF transmission from panel 3 Panel reset 4 Serial: Used for connecting the IP Internet Module/PCS (Data); also used for In-Field Firmware upgrade through a 307USB Direct Connect Interface 5 Antenna 6 RS485 connector 7 Zone Input 8 PGMs: these jumpers allows you to choose whether the solid state relay PGMs are grounded (-), or give out 12V (+). 9 Backup Battery connections 10 The BELL output will shutdown if the current exceeds 3A 11 AWG #14 single conductor solid copper wire 12 Ground clamp 13 Cold water pipe grounding 14 To ground 15 Keypad zone configuration 16 Zone connection, if EOL is enabled, see section [706] option 2, on page page 28 17 To connect additional wiring to auxiliary power, use the red (+) and black
(-) keypad connectors; auxiliary power will shut down if current exceeds 3A; if the auxiliary output is overloaded and shuts down, you must disconnect all loads from the output for at least 10 sec. before reconnecting any load back to the auxiliary output The sum of the current drawn from the BELL and AUX must be limited to 1.3A. Exceeding this limit will overload the panel power supply and lead to complete system shutdown. 40 VA transformer strongly recommended. This equipment must be installed and maintained by qualified service personnel only. Max. number of keypads: 15 keypads Max. aux. current: 700 mA Max. distance of bus module from panel: 76 m (250 ft.) Max. total run of wire: 230 m (750 ft.) 9 PCB Metal Box Installation The crosses and dotted line represent the PCB mounting location. If you need specific dimensions, contact Paradox Distributor Support. For UL recommended installation for the MG5000+ only, place the PCB one notch lower than the mounting location. MG5000+ (8x10) MG5000+ (11x11) MG5000+ / MG5050+ Installation Guide MG5050+ (11x11) Tamper Kit (TK278) For EN compliancy use the Tamper Kit TK278. Insert into one of the designated slots on the metal box and wire to an input. Tamper Kit Slot Tamper Kit Slot Secure screw to wall 10 MG5000+ / MG5050+ Installation Guide Auxiliary Power Terminals The auxiliary power supply terminals can be used to power motion detectors, keypads and other modules or accessories in the security system. A fuseless circuit protects the power supply against current overload and automatically shuts down if the current exceeds 1.1A. If this occurs, the Maximum Auxiliary Current failure will appear in the keypads trouble display (see Trouble Display on page 51). Therefore, the combined current consumption of devices connected to the auxiliary power supply should not exceed 700mA. If the auxiliary output is overloaded and is shut down, you must disconnect all loads from the output for at least 10 seconds before reconnecting any load back to the auxiliary output. Telephone Line Connection In order to report system events to the monitoring station, you must connect the incoming telephone company wires into the TIP and RING connections of the control panel and then run the wires from T1 and R1 to the telephone or telephone system as shown in PCB Layouts for each respective panel. Alarm Transmissions The mode of acknowledgment operation of the alarm transmission path is pass-through. In the case of network/interface failure, the control panel displays the trouble via the connected keypad(s). Examples of causes of this failure are prolonged power failure, communication path unavailable, system offline due to scheduled upgrades or maintenance. Substitution security is achieved by information security displayed on the keypad(s), physical security (provided by the tamper protection), and by a unique serial number for each device. Messages sent to the receiving center include the serial number to identify the substitution and alert accordingly. Information security is achieved by 256 bit encrypted, supervised communication (AES validation number is 986) which prevents unauthorized reading or modification of messages. Paradox alarm reporting systems are compatible with a variety of report code formats that are detailed in the Programming Guide. Bell Output Connection The BELL+ and BELL- terminals power bells, sirens and other warning devices requiring a steady voltage output during an alarm. The bell output supplies 12Vdc upon alarm and can support one 30-watt or two 20-watt sirens. The bell output uses a fuseless circuit and will automatically shut down if the current exceeds 3A. When this occurs the Maximum Bell Current failure will only appear in the keypads trouble display (see Trouble Display on page 51) during an alarm. If the load on the BELL terminals returns to normal, the control panel will re-instate power to the BELL terminals during the next alarm. When connecting sirens, please verify correct polarity. Connect the positive lead to the BELL+ terminal and the negative lead to the BELL- terminal of the control panel as shown in PCB Layouts for each respective panel. WARNING: If the BELL output is not being used, the Bell Disconnected failure will remain in the keypads trouble display (see Trouble Display on page 51). To avoid this connect a 1K resistor across the BELL terminals. For connection of a self-contained bell/siren, see PCB Layouts for each respective panel. Programmable Output Connections When a specific event occurs in the system, a PGM can reset smoke detectors, activate strobe lights, open/close garage doors and much more. PGMs The control panels include two/four on-board programmable outputs (PGMs). For details on how to program PGMs, see Programmable Outputs on page 44. PGM1 and PGM2 can support up to 150 mA. The PGMs are limited by the power source being used. If powered by:
The AUX terminals. The current consumption of the AUX terminals cannot exceed 700 mA. Therefore, whatever devices are connected to the AUX terminals
(i.e. modules and PGMs) cannot exceed 700 mA combined. For example, if there are six modules connected to the AUX terminals that are using 600 mA and you wish to power the PGM using the AUX terminals, the PGMs current consumption cannot exceed 100 mA. An external power supply. If using an external power supply, the current consumption cannot exceed 150 mA for PGM1 and PGM2. If the external power supplys current consumption limit is less than that of the PGM it is connected to, than the current consumption will not exceed the power supplys current limit. UL Note: The AUX terminals cannot exceed 200 mA for UL installations. Figure 2: Relay and PGM Connections 11 Single Zone Inputs Detection devices such as motion detectors and door contacts are connected to the control panel's zone input terminals. Figure 3 demonstrates single zone input terminal connections recognized by the panel. Once connected, the associated zone's parameters must be defined. Figure 3: Single Zone Input Connections MG5000+ / MG5050+ Installation Guide 12 MG5000+ / MG5050+ Installation Guide Advanced Technology Zone (ATZ) Connections The ATZ feature is a software oriented feature that enables two detection devices to be installed per hardwired input terminal. Each detection device has its own zone, displays its zone status on the keypad and sends its own alarm codes. Fire zones cannot be doubled. Figure 4: Advanced Technology Zone Connections 13 Fire Circuits When a zone is programmed as a fire zone, the zone becomes normally open and requires an EOL resistor. If a line short occurs or if the smoke detector becomes active, whether the system is armed or disarmed, the control panel will generate an alarm. If a trouble occurs on a fire zone, the Fire Loop Trouble will appear in the keypads trouble display (see Trouble Display on page 51) and the control panel can transmit the Fire Loop Trouble report, if programmed, in section [866]. Figure 5: Fire Circuits MG5000+ / MG5050+ Installation Guide 4-Wire and 2-Wire Installation:
For 4-wire installation, program the Activation Event so that the smoke detectors can be reset by pressing the [CLEAR] + [ENTER] keys for three seconds. See Event Group # 6 in the Event Description list in the programming guide. For 2-wire smoke detector installation, connect the 2-wire smoke detectors. If a line short occurs or the smoke detector activates, whether the system is disarmed, the control panel will generate an alarm. If the line is open, the Zone Fault trouble indication appears on the trouble display and the report code is sent to the monitoring station, if programmed. To reset 2-wire smoke detectors, press the [CLEAR] + [ENTER] keys for three seconds. 14 MG5000+ / MG5050+ Installation Guide Programming Methods BabyWare Software for Windows Program the control panels remotely or on-site using the BabyWare Software (V2.80 or higher) for Windows. For more information, contact your local Paradox Distributor or visit our web site at paradox.com. If you are using the BabyWare software, you must program the features (see Settings for BabyWare Software on page 49). Update the panels firmware by connecting it to a PC via a 307 Direct Connect Interface and then using the BabyWare software. Programming Using a Keypad Use the supplied programming guide to keep track of which sections were programmed and how. We recommend you read the entire manual before you begin programming. How Do I Enter Programming Mode?
1. 2. 3. 4. Press [ENTER]
Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default) Enter 3-digit [SECTION] you wish to program Enter required [DATA]
Single Digit Data Entry Method (Decimal and Hexadecimal) Single Digit Data Entry is used in all sections except those specified in the Feature Select Programming Method (below). After entering Programming Mode as described in the shaded box above, some sections will require that you enter Decimal values from 000 to 255. Other sections will require that you enter Hexadecimal values from 0 to F. The required data will be clearly indicated in this manual as well as in the programming guide. When entering the final digit in a section, the control panel will automatically save and advance to the next section. Except sections 001 to 032, after entering the first three digits the control panel will switch to Feature Select Programming. For phone number programming, press [ENTER] to save the data. Value or Action What Do I Press?
What Do I See?
Value 0 / Replace Current Digit with 0 Values 1 to 9 A (hex only) B (hex only) C (hex only) D (hex only) E (hex only) F (hex only) Exit Without Saving Save Data (hex only)
[sleep]
[1] to [9]
[0]
[off]
[byp]
[mem]
[tbl]
[clear]
[enter]
32-zone LED Erase digit and remain in section Zone 1 to 9 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 ARM & STAY LED flash Advances to the next section 10-zone LED Erase digit and remain in section
[1] to [9]
[0]
[off]
[byp]
[mem]
[tbl]
ARM & STAY LED flash Advances to the next section Feature Select Programming Method After entering certain sections, eight options will be displayed where each option from [1] to [8] represents a specific feature. Press the key corresponding to the desired option. This means the option is ON. Press the key again to remove the digit, thereby, turning OFF the option. When the options are set, press the [ENTER] key to save and advance to the next section. Data Display Mode (except K32LCD+) In the Data Display Mode you can view the programmed contents of each section one digit at a time. Figure 6: Data Display Mode To access the Data Display Mode, press the [ENTER] key after entering a section and before entering any data. The four LEDs as indicated below will begin to flash indicating that you are in the Data Display Mode. Each time the [ENTER] key is pressed, the keypad will display the next digit in the current section and will continue through all the following sections one digit at a time without changing the programmed values. Not available for sections using the Multiple Feature Select Method. Press the [CLEAR] key at any time to exit the Data Display Mode. 15 MG5000+ / MG5050+ Installation Guide Configuring the Keypad Zone Number
] and hold for three seconds How Do I Configure The Keypad?
Press [ENTER]
Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default) Press [
Enter the desired zone number key (K32+,K32LCD+: 2-digit entry 01 to 32, K10V/H: 1-digit entry 1 to 0(10)) Press [ENTER] to save and exit programming mode Press [CLEAR] to erase data without saving Press [CLEAR]+[CLEAR] to exit programming mode without saving Note: Please note that after five minutes, the keypad exits programming mode. 16 Special Function Keys Alphanumeric Key Input
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
A / B / C D / E / F G / H / I J / K / L M / N / O P / Q / R S / T / U V / W / X Y / Z MG5000+ / MG5050+ Installation Guide LCD Keypad Labels Input Keys Key
[stay]
[sleep]
[arm]
[off]
[byp]
[mem]
Function Insert space Delete Delete whole entry Toggle numeric/alphanumeric keys Toggle lower case/upper case Special characters Label Sections Label Sections
[181] to [212]
32 Zone Labels
[341] to [356]
16 PGM Labels
[511] to [542]
32 User Labels
[771] to [772]
[568] to [569]
[599] to [606]
[781] to [795]
2 Partition Labels 2 Wireless Labels 8 Wireless Keypads 15 Bus Modules Labels Polish Hungarian Turkish 001 001 002 003 Special Characters and Keypad Letter Assignment Polish / Hungarian / Turkish Special Character Catalogue Special Character Catalogue 001 002 003 004 005 006 007 17 Hebrew Keypad Letter Assignment Hebrew Special Characters Catalogue MG5000+ / MG5050+ Installation Guide 032 048 064 080 096 112 160 176 192 208 224 240 033 049 065 081 097 113 161 177 193 209 225 241 034 050 066 082 098 114 162 178 194 210 226 242 035 051 067 083 099 115 163 179 195 211 227 243 036 052 068 084 100 116 164 180 196 212 228 244 037 053 069 085 101 117 165 181 197 213 229 245 038 054 070 086 102 118 166 182 198 214 230 246 039 055 071 087 103 119 167 183 199 215 231 247 040 056 072 088 104 120 168 184 200 216 232 248 041 057 073 089 105 121 169 185 201 217 233 249 042 058 074 090 106 122 170 186 202 218 234 250 043 059 075 091 107 123 171 187 203 219 235 251 044 060 076 092 108 124 172 188 204 220 236 252 045 061 077 093 109 125 173 189 205 221 237 253 046 062 078 094 110 126 174 190 206 222 238 254 047 063 079 095 111 127 175 191 207 223 239 255 016 032 048 064 080 096 112 128 144 160 176 192 208 224 240 017 033 049 065 081 097 113 129 145 161 177 193 209 225 241 018 034 050 066 082 098 114 130 146 162 178 194 210 226 242 019 035 051 067 083 099 115 131 147 163 179 195 211 227 243 020 036 052 068 084 100 116 132 148 164 180 196 212 228 244 021 037 053 A069 085 101 117 133 149 165 181 197 213 229 245 022 038 054 070 086 102 118 134 150 166 182 198 214 230 246 023 039 055 071 087 103 119 135 151 167 183 199 215 231 247 024 040 056 072 088 104 120 136 152 168 184 200 216 232 248 025 041 057 073 089 105 121 137 153 169 185 201 217 233 249 026 042 058 074 090 106 122 138 154 170 186 202 218 234 250 027 043 059 075 091 107 123 139 155 171 187 203 219 235 251 028 044 060 076 092 108 124 140 156 172 188 204 220 236 252 029 045 061 077 093 109 125 141 157 173 189 205 221 237 253 030 046 062 078 094 110 126 142 158 174 190 206 222 238 254 031 047 063 079 095 111 127 143 159 175 191 207 223 239 255 Greek Keypad Letter Assignment Greek Special Characters Catalogue Press key once Press key twice Press key three times A D H K N P T C B E Q L R U Y G Z I M O S F W Key
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
18 MG5000+ / MG5050+ Installation Guide Russian Keypad Letter Assignment Russian Special Characters Catalogue 19 MG5000+ / MG5050+ Installation Guide The control panel supports the following access codes:
Access Codes Installer Code [397]:
Maintenance Code [398]:
System Master Code [399]:
Master Code 1:
Master Code 2:
29 User Codes:
Used to program all control panel settings except user access codes. The Maintenance code is similar to the Installer code. It can be used to enter programming mode, which allows you to pro-
gram all the features, options and commands except for the panels communication settings. The maintenance code is empty by default. Provides full access. Arm and disarm using any method described in the User Code Options below as well as program the user access codes. Permanently assigned to partition 1. Same as a regular user code except it can also program access codes for user codes assigned to partition 1. Permanently assigned to partition 2. Same as a regular user code except it can program access codes for user codes assigned to partition 2. If the system is not partitioned Master Code 2 will be assigned to partition 1. Can arm and disarm as per User Code Options on page 20. Access Code Length Section [701]: System Options Option [1] OFF= 6-Digit Access Codes (valid code entries include 000000 to 999999) Option [1] ON= 4-Digit Access Codes (default) (valid code entries include 0000 to 9999) All access codes can be set to lengths of either 4- or 6-digits. When the 4-digit option is selected, entering a 4-digit code will allow access. Using the 6-digit option, entering 6 digits is required to allow access. WARNING: If the access code length is changed from four digits to six digits when access codes have already been programmed, the control panel will automatically add the last 2 digits by using the first 2 digits. For example, if the access code is 1234 and you switch to 6 digits, the code will become 123412. Be sure to verify the access codes after switching from 4-digit access codes to 6-digit codes. When switching from six digits to four digits, the control panel will simply remove the final two digits of the access code. For example, 123456 will become 1234. Installer Code (Default: 0000 / 000000) The Installer Code is used to enter the systems programming mode, which allows you to program all the features, options and commands of the control panel. The Installer Code can be 4- or 6-digits in length (see Access Code Length on page 20) where each digit can be any value from 0 to 9. The Installer Code cannot be used to program Master Code 1, Master Code 2 or user access codes. To program the Installer Code press:
[ENTER]+ [CURRENT INSTALLER CODE] + [397] + new 4- or 6-digit Installer Code Maintenance Code (Default: Empty) The Maintenance code is similar to the Installer code. It can be used to enter programming mode, which allows you to program all the features, options and commands except for the systems communication settings (sections [395], [397], [398], [815], [816], [817], [910], and [911]) as well as any user codes. The Maintenance code can be 4 or 6 digits in length where each digit can be any value from 0 to 9. The Maintenance code is empty by default. Set the Maintenance in section [398].
[ENTER]+ [INSTALLER CODE] + [398] + new 4- or 6-digit Maintenance Code System Master Code (Default: 1234 / 123456) The Installer Code can be used to program the System Master Code. With the System Master Code a user can use any arming method and can program any user access code, but not the User Code Options. The System Master Code can be 4 or 6 digits in length, where each digit can be any digit from 0 to 9. The System Master Code can be modified but cannot be erased. To change the System Master Code press:
[ENTER]+ [INSTALLER CODE] + [399] + new 4- or 6-digit System Master Code User Code Options Sections [404] to [432]: Options [1] to [8]
The User Code Options define which arming methods each user can use to arm or disarm the system. Regardless of these settings, all users can Regular arm assigned partitions and all users except those with the Arm Only option can disarm an assigned partition, regardless of how it is armed. Select one or more of the options described on the following pages for each user access code, where sections [404] to [432] represent user access codes 004 to 032. Partition 1 Assignment Sections [404] to [432]: User codes 004 to 032 Option [1] OFF= Deny access to partition 1 Option [1] ON= User code has access to partition 1 (default) If the system is partitioned (see Partitioning on page 46), user codes with this option enabled can arm and disarm partition 1. WARNING: If the system is not partitioned, you must assign partition 1 to the user access code. Otherwise, the user access code will be considered disabled. 20 If the system is partitioned (see Partitioning on page 46), user codes with this option enabled can arm and disarm partition 2. If the system is not partitioned, the control panel ignores this option. MG5000+ / MG5050+ Installation Guide Partition 2 Assignment Sections [404] to [432]: User Codes 004 to 032 Option [2] OFF= Deny access to partition 2 (default) Option [2] ON= User code has access to partition 2 Bypass Programming Sections [404] to [432]: User Codes 004 to 032 Option [3] OFF= Bypass Programming Disabled Option [3] ON= Bypass Programming Enabled (default) User codes with this option enabled can perform Bypass Programming in assigned partitions. Stay/Sleep Arming Sections [404] to [432]: User Codes 004 to 032 Option [4] OFF= Stay/Sleep Arming Disabled Option [4] ON= Stay/Sleep Arming Enabled for selected User Code (default) User codes with this option enabled can Stay or Sleep arm assigned partitions. Force Arming Sections [404] to [432]: User Codes 004 to 032 Option [5] OFF= Force Arming Disabled Option [5] ON= Force Arming Enabled for selected User Code (default) User codes with this option enabled can Force arm assigned partitions. Arm Only Sections [404] to [432]: User Codes 004 to 032 Option [6] OFF= Arm Only Disabled (default) Option [6] ON= Arm Only Enabled for selected User Code The user code with this option enabled can arm assigned partitions, but cannot disarm any partitions. The type of arming is dependent on the other User Code Options selected. Please note that with the Arm Only option, the user can cancel a recently armed system by re-entering the access code before the end of the exit delay. PGM Activation Sections [404] to [432]: User Codes 004 to 048 Option [7] OFF= User Code follows User Code Options and can activate a PGM (default) Option [7] ON= User Code can activate a PGM only With option [7] off, entering the access code will arm or disarm according to the programmed User Code Options as well as activate or deactivate a PGM. The appropriate PGM Activation/Deactivation Event must also be programmed (see Programmable Outputs on page 44). With option [7] on, the control panel will ignore all other User Code Options. Therefore, entering the access code will only activate or deactivate the PGM. If you are coerced into arming or disarming your system, entering the access code with the duress option enabled will arm or disarm the system and immediately transmit a silent alert (Duress Code) to the monitoring station. Duress Sections [404] to [432]: User Codes 004 to 032 Option [8] OFF= User Code with duress disabled (default) Option [8] ON= User Code with duress enabled Lock Master Code Section [701]: System Options Option [2] OFF= Lock System Master Code Disabled (default) Option [2] ON= Lock System Master Code Enabled With this feature enabled, the control panel will lock the System Master Code (001), it cannot be modified. With this feature disabled, the control panel will unlock the System Master Code, so that it can be changed. The System Master Code cannot be deleted (see Master Quick Menu Programming in the User Guide). 21 MG5000+ / MG5050+ Installation Guide StayD Mode Overview Entry/Exit Paths NOTE: StayD is automatically enabled when a path is programmed to a keypad. When deleting a wireless keypad from the system, the corresponding path zones will also be deleted. StayD simplifies your life and makes it safer by protecting you 24 hours a day, 7 days a week without ever having to disarm the system - even when entering an armed area. StayD lives with you and protects you at all times, without any unprotected periods, and while automatically rearming the system so you dont have to remember to do it. This unique feature integrates security into your everyday life to give you safe, simple living with peace of mind. StayD consists of programmed pathways, where the user enters and exits the property through pre-defined routes, with only the routes respective zones open for passage. A path can be programmed for each individual keypad, with a maximum of four zones per path. Path zones must be defined as follow or delay zones only. StayD is automatically enabled when a path is programmed to a keypad. The first zone programmed in a path is its designated entry point (e.g. doors, garage). Designated entry points are not common to multiple paths. There is only one designated entry point per path. Also, they are only used when entering/exiting with a remote control (see below). The system only disables the path zones corresponding to the keypad at the point of entry/exit, while re-arming as you enter/exit. If another path zone opens before trying to disarm the system, you can validate the zone by entering your user code. For example, you have entered your home through Path 1 and are at your keypad. Before disarming the system, you notice a Path 2 zone has opened. If you know it is a member of your family and would like to validate the open zone, enter your user code. All paths, including Path 1, will subsequently be validated. If the path 2 zone opens after you have entered your code to validate Path 1, you must enter your code again to validate Path 2. You must enter your code for every zone that opens that is not part of any path. For example, if you have entered through Path 1 and a non-path zone opens, you must enter your code once to validate your path and once for the non-path zone. If you do not validate the non-path zone, the system will fall in alarm. Entry/Exit with a Keypad When entering with a keypad, the path zones will fall into entry delay, allowing you to reach the keypad. Use the keypad to disarm the system and switch to Stay arm mode. When exiting with a keypad, only the path zones will fall into delay (same as exit delay), allowing you to leave while the rest of the premises remains secure. Entry/Exit with a Remote Control When using a remote control, the path you use is defined by a designated entry point. For example: if after pressing the remote control to disarm the system you trigger zone 1, the system will check to see which path(s) include zone 1. All paths that include zone 1 will open. Only after reaching the designated entry point will the system know which path you are taking, and thus will re-arm all other paths. After entry with a remote, the system will automatically arm in Stay mode. To disarm the system with a remote control: Press four times to cancel the exit delay and arm the system in Stay mode. once to disarm partition 1, twice for partition 2, and three times for both partitions. Press the button Window Mode and Re-arm Delay In a Stay-armed system: This mode allows you to open one exterior zone without triggering an alarm. To enter Window mode, press [OFF], then your [ACCESS CODE]. All zones that can be opened flash. The system will start an exit delay, allowing you to open an exterior zone such as a window or a door. The system will only allow you to open one zone as the exit delay will end after doing so. When you close the open zone (window, door, etc.) that zone will re-arm. Re-arm Delay is a delay timer set so that when you close the open exterior zone (window, door etc.), it does not re-arm instantly. Instead the system starts the delay to allow you to close the zone properly. The delay will start every time you open the zone while trying to close it, and you must close the zone for 5 seconds for it to arm. This is especially useful for eliminating false alarms caused by windows that stick. Advanced Settings Section Data
[720]
(000 to 255) sec. Description Flex-Instant = Instant and follow zones will follow the delay at section [720] when Stay or Sleep armed (default is 15 seconds / 000 = instant zone). Section
[721]
Data __/__/__
(000 to 255) sec. Description Re-arm delay (delay before zone re-arms). Default = 000 (no delay) 22 MG5000+ / MG5050+ Installation Guide Zone Programming When programming zones, the zone assignments are dependent on the designation of the wireless transmitters, assignment of keypad zones, and the detection devices that are connected to the panel. For keypad assignment, see Configuring the Keypad Zone Number on page 16. After assigning the required zones, you must set the zones definitions, partition assignment, and options see Figure 7 below. Certain Zone Definitions change if a Flex-Instant delay is activated (section
[720]). See see Zone Definition Status on page 26. Table 1: Zone Recognition Table Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 to 32 Wireless Yes Yes Yes Yes Yes Keypad Yes Yes Yes Yes Yes Hardwire Yes (Input Z1) Yes (Input Z2) Yes (Input Z1 with ATZ) Yes (Input Z2 with ATZ) No NOTE: If a zone is already programmed and you assign a device to the same zone, a wireless zone will overwrite a keypad/hardwire zone, and a keypad zone will overwrite a hardwire zone. Figure 7: Zone Programming Zone Definitions 00 = Zone disabled 01 = Entry Delay 1 02 = Entry Delay 2 03 = Entry Delay 1 (Full Arm) 04 = Entry Delay 2 (Full Arm) 05 = Follow 06 = Follow (Sleep / Full Arm) 07 = Follow (Full Arm) 08 = Instant 09 = Instant (Sleep / Full Arm) 10 = Instant (Full Arm) 11 = Instant Fire 12 = Delayed Fire 13 = Instant Fire Silent 14 = Delayed Fire Silent 15 = 24Hr. Buzzer 16 = 24Hr. Burglary 17 = 24Hr. Hold-up 18 = 24Hr. Gas 19 = 24Hr. Heat 20 = 24Hr. Water 21 = 24Hr. Freeze 22 = 24Hr. Panic 23 = Instant No Pre-Alarm 24 = Follow no Pre-Alarm 25 = Keyswitch Maintain*
26 = Keyswitch Momentary*
* On-board hardwire control panel zones only Zone Options
[1] = Auto-zone Shutdown
[2] = Bypassable Zone
[3] = RF Zone Supervision
[4] [5]
OFF OFF Audible Alarm OFF ON Pulsed Alarm ON OFF Silent Alarm ON ON Report Only
[6] = Intellizone
[7] = Delay alarm transmission
[8] = Force Zone Partition Assignment
[1]- Partition 1
[2]- Partition 2
[3]- Both partitions Section
[001] = Zone 1
[032] = Zone 32 Zone Definition _____/_____ _____/_____ Partition Assignment _____________ _____________ Zone Options 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Zone Definitions As demonstrated in Figure 8 above, sections [001] to [032] represent zones 1 through 32 respectively, where the first two digits in each of these sections represents the zone's definition. To disable a zone, enter [00]. There are 26 available Zone Definitions. Entry Delay 1 Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 01 When the system is armed and a zone defined with Entry Delay 1 opens, the control panel will generate an alarm after the programmed Entry Delay 1 Timer elapses. This is to provide users with enough time to enter the protected area and disarm the system. To program the Entry Delay 1 Timer, key in the desired 3-digit delay value (000 to 255 seconds, Default = 45 seconds) into section [710]. Entry delay zones are commonly used at the entry/exit points of the protected area (e.g., front/
back door, garage, etc.). Using different entry delays is useful when, for example, one entry point requires a longer delay than the other entry point or in a partitioned system where each partition may require a different entry delay. Entry Delay 2 Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 02 Entry Delay 1 (Full Arm) Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 03 Entry Delay 2 zones are identical to the Entry Delay 1 zones, except it uses a separate entry delay timer. To program the Entry Delay 2 Timer, key in the desired 3-digit delay value (000 to 255 seconds, Default = 45 seconds) into section [711]. Upon regular arming, the zone is Entry Delay 1 (see Entry Delay 1 Zones on page 23). Upon Stay/Sleep arming, the zone is bypassed by the system. See Zone Definition Status on page 26 for any exceptions. 23 MG5000+ / MG5050+ Installation Guide Entry Delay 2 (Full Arm) Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 04 Follow Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 05 Upon regular arming, the zone is Entry Delay 2 (see Entry Delay 2 Zones on page 23). Upon Stay/Sleep arming, the zone is bypassed by the system. See Zone Definition Status on page 26 for any exceptions. When a Regular, Stay, or Sleep armed Follow Zone opens, the control panel will immediately generate an alarm, unless an entry delay zone opens first:
If a Regular/Stay/Sleep armed Follow Zone opens after an entry delay zone opens, the control panel waits until the entry delay timer has elapsed before generating an alarm. If a Regular/Stay/Sleep armed Follow Zone opens after more than one entry delay zone opens, the control panel will wait until the entry delay timer of the zone that opened first has elapsed. This feature is commonly used when a motion detector is protecting the area occupied by the entry point keypad. This will prevent the motion detector from causing an alarm when a user enters through the entry point to disarm the system. See Zone Definition Status on page 26 for any exceptions. Upon regular arming or sleep arming, the zone is Follow. Upon Stay arming, the zone is bypassed by the system. See Zone Definition Status on page 26 for any exceptions. Follow (Sleep / Full Arm) Sections [001] to [032]: Zones 1 to 32, First Digits = 06 Follow (Full Arm) Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 07 Instant Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 08 Instant (Sleep / Full Arm) Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 09 Instant (Full Arm) Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 10 Upon regular arming, the zone is Follow (see Follow Zones on page 24). Upon Stay or Sleep arming, the zone is bypassed by the system. See Zone Definition Status on page 26 for any exceptions. When an armed Instant Zone opens, the control panel immediately generates an alarm. Instant Zones are commonly used for windows, patio doors, skylights and other perimeter type zones. See Zone Definition Status on page 26 for any exceptions. When Regular or Sleep arming, the zone is Instant. When Stay arming, the zone is bypassed by the system. See Zone Definition Status on page 26 for any exceptions. Upon Regular arming, the zone is Instant. Upon Stay or Sleep arming, the zone is bypassed by the system. See Zone Definition Status on page 26 for any exceptions. Instant Fire Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 11 when a Instant Fire zone opens, whether it is armed or disarmed, the control panel will send the corresponding Alarm Report Code and the alarm is always audible regardless of other settings. Fire alarms generate an intermittent (pulsed) bell/siren output signal as shown in Figure 8 on page 24. Figure 8: Bell/Siren Output during a Fire Alarm 24 MG5000+ / MG5050+ Installation Guide Delayed Fire Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 12 When a Delayed 24Hr. Fire zone opens, whether it is armed or disarmed, the control panel will react as shown in Figure 9. Delayed 24Hr. Fire zones are commonly used in residential homes where a smoke detector often generates false alarms (e.g., burning bread, etc.). Fire alarms generate an intermittent
(pulsed) bell/siren output signal as shown in Figure 8 above. Figure 9: Delayed 24Hr Fire Zone Instant Fire Silent Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 13 When a Instant Fire Silent zone opens, whether it is armed or disarmed, the control panel will generate the following:
The control panel can send the corresponding Alarm Report Code and the alarm will be silent regardless of other settings. Delayed Fire Silent Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 14 When a Delayed Fire zone opens, whether it is armed or disarmed, the control panel will react as shown in Figure 9. Delayed 24Hr. Fire zones are commonly used in residential homes where a smoke detector often generates false alarms (e.g., burning bread, etc.). The control panel can send the corresponding Alarm Report Code and the alarm will be silent regardless of other settings. 24 Hr. Buzzer Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 15 When a 24Hr Buzzer Zone opens, whether the zone is armed or disarmed, the control panel sets off the keypads buzzers to indicate that the zone was breached. The control panel will report the alarm, but will not enable the bell/siren output. Enter any valid access code on the keypad to stop the buzzer. This zone definition is particularly useful when a user wishes to be notified when something such as a safe or locker within the home has been accessed (e.g., a child accessing a valuable collection). 24 Hr. Burglary Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 16 When a 24Hr Burglary Zone opens, whether the system is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 27. 24 Hr. Hold-up Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 17 24 Hr. Gas Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 18 24 Hr. Heat Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 19 24 Hr. Water Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 20 When a 24Hr. Hold-up zone opens, whether it is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 27. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Hold-up alarm. When a 24Hr. Gas zone opens, whether it is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 27. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Gas alarm. When a 24Hr. Heat zone opens, whether it is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 27. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Heat alarm. When a 24Hr. Water zone opens, whether it is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 27. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Water alarm. 25 MG5000+ / MG5050+ Installation Guide 24 Hr. Freeze Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 21 24Hr. Panic Sections [001] to [032]: Zones 1 to 32, First Digits = 22 When a 24Hr. Freeze zone opens, whether it is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 27. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Freeze alarm. When a 24Hr. Panic zone opens, whether it is armed or disarmed, the system will immediately generate an alarm. This alarm is defined by the panic options set in section [702]. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Panic alarm. Section [702] option [1] (Panic 1) must be enabled for the 24Hr. Panic zone to function. Instant No Pre-Alarm Sections [001] to [032]: Zones 1 to 32, First Digits = 23 This zone definition ignores the Flex-Instant delay, and acts like a traditional Instant zone. Follow No Pre-Alarm Sections [001] to [032]: Zones 1 to 32, First Digits = 24 This zone definition ignores the Flex-Instant delay, and acts like a traditional Follow zone. Zone Definition Status There are eight zone definitions that are affected by the Flex-Instant delay (section [720]). The following table shows how the zone definition changes depending on the arm status and if the Flex-Instant delay is enabled. see Zone Definition Status on page 26 Zone Definitions 01 = Entry Delay 1 02 = Entry Delay 2 03 = Entry Delay 1 (Full Arm) 04 = Entry Delay 2 (Full Arm) 05 = Follow 06 = Follow (Sleep/Full Arm) 07 = Follow (Full Arm) 08 = Instant 09 = Instant (Sleep/Full Arm) 10 = Instant (Full Arm) 23 = Instant No Pre-Alarm 24 = Follow No Pre-Alarm Stay Arm Entry Delay 1 Entry Delay 2 Not Armed Not Armed Follow*
Not Armed Not Armed Instant*
Not Armed Not Armed Instant Follow Sleep Arm Entry Delay 1 Entry Delay 2 Not Armed Not Armed Follow*
Follow*
Not Armed Instant*
Instant*
Not Armed Instant Follow Fully Arm Entry Delay 1 Entry Delay 2 Entry Delay 1 Entry Delay 2 Follow*
Follow Follow Instant*
Instant Instant Instant*
Follow*
* Flex-Instant = Zone will follow the delay at section [720], (default is 15 seconds / 0 = instant zone) Zone Partition Assignment Sections [001] to [032]: Zones 1 to 32 The control panel provides the option of partitioning the security system into two completely independent systems. Sections [001] to [032] represent zones 1 through 32 respectively, where the third digit in each of these sections represents the zone's partition assignment. The zone is assigned to Partition 1 if third digit = 1, Partition 2 if third digit = 2, or both partitions is third digit = 3. For more details, see Partitioning on page 46. Zone Options Sections [001] to [032] represent zones 1 through 32 respectively. After entering the definition and partition assignment, select one or more of the following Zone Options by using the Multiple Feature Select Programming Method:
26 MG5000+ / MG5050+ Installation Guide Auto Zone Shutdown Sections [001] to [032] = Zones 1 to 32 Option [1] OFF= Auto Zone Shutdown Disabled Option [1] ON= Auto Zone Shutdown Enabled for selected zone (default) Bypassable Zones Sections [001] to [032] = Zones 1 to 32 Option [2] OFF= Bypass Zone Disabled Option [2] ON= Selected Zone is Bypass Enabled (default) If, in a single armed period, the number of alarms generated by a zone with the Auto Zone Shutdown option enabled exceeds the number defined by the Auto Zone Shutdown Counter, the control panel will no longer generate an alarm for that zone. To program the Auto Zone Shutdown Counter, key in the desired limit
(000=Disabled, 001 to 015, Default = 5) into section [712]. The Auto Zone Shutdown Counter resets every time a valid code is entered. When a user utilizes the Bypass Programming feature (see Bypass Programming on page 21), only zones with the Bypass option enabled can be programmed as bypassed. Do not program a fire zone with the Bypass option, as the control panel will never bypass fire zones. RF Zone Supervision Sections [001] to [032]: Zones 1 to 32 Option [3] OFF= RF Zone Supervision Disabled Option [3] ON= RF Zone Supervision Enabled (default) The panel waits for each of its assigned wireless transmitters to send a status signal within a specified time period (section [706], option [1]) to confirm their presence and functionality. If a device has not sent a signal within that time period, the control panel can generate a trouble, an alarm, and/or transmit a report code to the monitoring station. See Trouble Display on page 51. Alarm Types Sections [001] to [032]: Zones 1 to 32
[4] OFF / [5] OFF: Audible Steady (default) When the conditions for an alarm have been met, the control panel can transmit the appropriate Zone Alarm report code and provides a steady output for any bells or sirens connected to the control panels bell output.
[4] OFF / [5] ON: Audible Pulsed Alarm When the conditions for an alarm have been met, the control panel can transmit the appropriate Zone Alarm report code and provides a pulsed output (see Figure 8 on page 24) for any bells or sirens connected to the control panels bell output.
[4] ON / [5] OFF: Silent Alarm When the conditions for an alarm are met, the control panel can transmit the appropriate Zone Alarm report code and will not activate the control panels bell output. The appropriate ARM or STATUS LED on the keypads will flash to indicate an alarm and the user will still have to disarm the system.
[4] ON / [5] ON: Report Only When the conditions for an alarm have been met, the control panel can transmit the appropriate Zone Alarm report code. The system will not have to be disarmed. Intellizone Sections [001] to [032]: Zones 1 to 32 Option [6] OFF= Intellizone Disabled (default) Option [6] ON= Intellizone Enabled for Selected Zone This feature reduces the possibility of false alarms. When a zone with the Intellizone option opens, the panel does not immediately generate an alarm. First it triggers the Intellizone Delay Timer. To program the Intellizone Delay Timer, key in the desired 3-digit value (000 to 255 seconds, Default = 48 seconds) into section
[713]. If any of the following conditions occur during this period, the panel will generate an alarm:
During the Intellizone Delay, a second zone has caused an alarm. During the Intellizone Delay, the zone in alarm has restored (closed) and re-occurred (opened). The zone in alarm remains open for the entire Intellizone Delay. Delay Alarm Transmission Sections [001] to [032]: Zones 1 to 32 Option [7] OFF= Delay Alarm Transmission Disabled (default) Option [7] ON= Delay Alarm Transmission Enabled for Selected Zone When an alarm condition occurs on a zone with this option enabled, the control panel enables the bell/siren output, but does not report the alarm to the monitoring station until the end of the Delay Alarm Transmission. To program the Delay Alarm Transmission, key in the desired 3-digit delay value (000 = Disabled, 001 to 255 seconds) into section [833]. During this period, disarming the system disables the bell/siren output and cancels the report code transmission. This feature is commonly used with entry delay zones to reduce false alarms created by new users who may not disarm the system in time. 27 MG5000+ / MG5050+ Installation Guide Any open Force Zones at the time of arming will be considered deactivated by the control panel. If during this period a deactivated zone is closed, the control panel will revert that zone to active status. Consequently, the control panel will generate an alarm if the zone is breached. Do not program a fire zone with the Force option, as the control panel will never bypass fire zones when Force arming. If all detection devices connected to the control panel have input terminals that require 1K end of line resistors, enable option [2] in section [706]. For details on using EOL resistors, see Single Zone Inputs on page 12 Force Zones Sections [001] to [032]: Zones 1 to 32 Option [8] OFF= Force Zone Disabled Option [8] ON= Selected Zone is Force Enabled (default) EOL Zones Section [706]: Zone Options Option [2] OFF= Zones do not use EOL resistors (default) Option [2] ON= Zones require EOL resistors ATZ Zone Doubling Section [705]: General Zone Options Option [1] OFF= ATZ zone doubling disabled (default) Option [1] ON= ATZ zone doubling enabled Tamper Input on ZX8/ZX82 ID A (Panel + 1) Section [706]: General Zone Options 2 Option [4] OFF= Zone A (default) Option [4] ON= Tamper input Tamper Input on ZX8/ZX82 ID B (Panel + 9) Section [706]: General Zone Options 2 Option [5] OFF= Zone B (default) Option [5] ON= Tamper input Tamper Input on ZX8/ZX82 ID C (Panel + 17) Section [706]: General Zone Options 2 Option [6] OFF= Zone C (default) Option [6] ON= Tamper input Enabling ATZ Zone Doubling allows you to install two detection devices per input terminal. Enabling this option will make the first zone on the ZX8/ZX82 ID A (Panel +1) a tamper input. By default, it is a zone. Enabling this option will make the first zone on the ZX8/ZX82 ID B (Panel +9) a tamper input. By default, it is a zone. Enabling this option will make the first zone on the ZX8/ZX82 ID C (Panel +17) a tamper input. By default, it is a zone. ATZ Wiring Options Section [705]: General Zone Options Option [2] OFF= ATZ Series (default) Option [2] ON= ATZ Parallel doubling enabled ATZ Zone Doubling can be configured in either a series or parallel connection. Zone Input 1 Becomes a 2-wire Smoke Input Section [706]: General Zone Options Option [3] OFF= Zone input 1 is a standard zone input (default) Option [3] ON= Zone input 1 becomes a 2-wire smoke input With this option enabled, zone input 1 becomes a 2-wire smoke input. Zone Timers Sections [041] to [044]: Zones 1 to 4 001 to 255 x 10 ms, Default = 060 28 The Zone Timer defines how quickly the control panel will respond to an open zone. The control panel will not display an open zone on the keypad or generate an alarm until the programmed Zone Timer has elapsed. All other zone definitions and options do not come into effect until the Zone Timer has elapsed. This feature prevents any momentary glitches from causing an alarm or unnecessary reporting. MG5000+ / MG5050+ Installation Guide Keyswitch Programming Keyswitch Numbering On-board hardwire control panel zones only. Keyswitch Numbering allows you to assign any hardwired input in the system to any of the 32 keyswitch zones in the control panel. Keyswitch Definitions Keyswitch Definitions determine how a keyswitch is used. Maintained Keyswitch On-board hardwire control panel zones only. To arm a partition using the Maintained Keyswitch, turn the switch from the ON to the OFF position. Disarm it by setting the key on the ON position. Momentary Keyswitch On-board hardwire control panel zones only. To arm or disarm a partition using the Momentary Keyswitch, turn the keyswitch to the ON position for three seconds, then turn it to the OFF position. Keyswitch Options Each keyswitch zone can be programmed with one or more options. Stay/Sleep Disarm Option (Keyswitch) On-board hardwire control panel zones only: Option 4 When enabled, the keyswitch can only disarm assigned Stay or Sleep armed partitions. When option [4] is disabled, the keyswitch can disarm partitions armed using any arming method. Arm Only (Keyswitch) On-board hardwire control panel zones only: Option 5 When enabled, the keyswitch can only arm assigned partitions. The type of arming is determined by the other Keyswitch Options selected. Stay Arming (Keyswitch) On-board hardwire control panel zones only: Option 6 Activating the keyswitch will Stay Arm the partition. Sleep Arming (Keyswitch) On-board hardwire control panel zones only: Option 7 Activating the keyswitch will Sleep Arm the partition. Only one of the arming options (Stay, Force, Instant and Regular) can be selected. 29 MG5000+ / MG5050+ Installation Guide Wireless Features Supervision Options For information on how to configure wireless modules, please refer to the appropriate modules installation guide for details. Please note that configuration for the wireless modules can only be done via a TM50/TM70 keypad. The Supervision Options cannot be used with any remote controls assigned to the control panel. Supervision Bypass Options Section [705]: Arming/Disarming Options Option [8] ON= Generate Supervision Loss if detected on a Bypassed Wireless Transmitter Zone (default) Option [8] OFF = No Supervision Loss if detected on a Bypassed Wireless Transmitter Zone When this feature is disabled, the Wireless Transmitter Supervision Options will follow the zones bypass definition. This means the control panel will not perform any action if a Supervision Loss occurs on a bypassed zone. When this feature is enabled, the Wireless Transmitter Options will ignore the bypass definition. This means the control panel will generate an incident as per Wireless Transmitter Supervision Options if a supervision loss occurs on a bypassed zone. RF Module Supervision Timer Settings Section [706]: Supervision Options Option [1] OFF= Check-in supervision interval is every 24 hours (default) Option [1] ON= Check-in supervision interval is every 80 minutes Option [1] defines the time period that the control panel will expect a check-in status signal from its assigned wireless transmitters. For example, if the timer is set to 80 minutes (option [1] = ON), the control panel will expect a check-in status signal to be sent from its assigned wireless transmitters within 80 minutes. If the control panel does not receive a signal from one of its wireless transmitters within the period of time defined here, it can then generate a trouble, an alarm, and/or can transmit a report code to the monitoring station (see Supervision Options on page 30). RF Jamming Supervision Section [700]: Zone Options Option [5] OFF= RF Jamming Supervision Disabled Option [5] ON= RF Jamming Supervision Enabled (default) With option [5] ON, a trouble will be generated when the panels RF signal is jammed or encounters interference for a minimum of 10 seconds. Remote Control Programming The control panel accepts up to thirty-two fully programmable remote controls. Programming the remote controls is accomplished in two steps:
1. 2. Assign the remote controls to the control panel. Program the buttons on the remote controls. Assigning a Remote Control to the Control Panel Sections [651] to [682]: Remote Controls 1 to 32 respectively Remote controls are assigned to the panel using the Automatic Learning method via the Master Quick Menu Programming or by entering the serial number. How Do I Assign a Remote Control to the Control Panel?
1. 2. 3. 4. Press the [ENTER] key. Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default) Enter the desired [SECTION NUMBER] (from sections [651] to [682]). Enter the six-digit serial number of the remote. Deleting Assigned Remote Controls Sections [651] to [682]: Remote Controls 1 to 32 respectively Remote controls can be deleted by deleting the corresponding user (see the Quick Menu in the user guide). How Do I Delete a Remote Control?
1. 2. 3. 4. Press the [ENTER] key. Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default) Enter the desired [SECTION NUMBER] (from sections [651] to [682]). Press the [0] button six times to delete the serial number. 30 MG5000+ / MG5050+ Installation Guide Programming the Remote Control Buttons Sections [611] to [642]: Remote Controls 1 to 32 respectively. Each remote control can be programmed to perform up to 4 different actions. Each digit in sections [611] to [642] represents a button or combination of buttons. Digits 1 through 4 can be programmed, while digits 5 through 8 are reserved for future use and must be defined as empty (reminder: [SLEEP] = empty). How Do I Program the Remote Controls Buttons?
1. 2. 3. 4. Press the [ENTER] key. Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default) Enter the desired [SECTION NUMBER] (from sections [610] to [642]). Enter the [HEXADECIMAL VALUE] (0 to F) of the desired button option from table 2 on page 31 in the appropriate space. If you do not wish to program a button combination, press the [SLEEP] key to skip. Warning: When section [610] is accessed, the panel will copy the saved value of that section to all remotes. Table 2: Button Options
[0] = Button Disabled*
[8] = Generate a Panic 1 Alarm
[1] = Regular/Regular Force arming
[9] = Generate a Panic 2 Alarm
[2] = Stay/Stay Force arming
[0] or [0(10)] = Generate a Panic 3 Alarm
[4] = Sleep/Sleep Force arming
[BYP] = Activates any PGMs that have Event Group #09 as their Activation Event
[OFF] = Activates any PGMs that have Event Group #08 as their Activation Event
[MEM] = Activates any PGMs that have Event Group #10 as their Activation Event
[TBL] = Activates any PGMs that have Event Group #11 as their Activation Event
[3] = N/A
[5] = N/A
[6] = N/A
[7] = N/A
* If you do not enter a value for a button, that button is disabled.
] = Paramedic alarm 31 MG5000+ / MG5050+ Installation Guide Arming and Disarming Options Switch to Stay Arming if no Entry Delay is opened Section [741]: Partition 1, Section [742] = Partition 2 Option [5] OFF= Switch to Stay Arming Disabled (default) Option [5] ON= Switch to Stay Arming Enabled If a user Regular arms a partition, but does not exit through (open and close) an entry delay zone during the exit delay, the control panel can be programmed to switch from Regular arming to Stay arming. When Delay Zone is bypassed Follow Zones become Entry Delay 2 Section [741]: Partition 1, Section [742] = Partition 2 Option [6] OFF= Follow zones become entry delay 2 when delay zone is bypassed disabled (default) Option [6] ON= Follow zones become entry delay 2 when delay zone is bypassed enabled If a user has an entry point defined as a delay, and a motion detector set as a follow zone, this option allows the user to bypass a delay zone so that the motion detector becomes an entry delay 2 zone. For example, if a user has a malfunctioning door contact, they can bypass the delay zone and have the motion detector become an entry delay 2 zone so that they have sufficient time to disarm the system. All follow zones become entry delay 2 if at least one delay zone is bypassed. With this feature enabled, the control panel will always Force arm (if a force-enabled zone is open, see Force Zones on page 28) instead of Regular arm when a valid user access code with the Force Arming Option is entered. With this feature enabled, the control panel will always Stay Force arm (if a force-enabled zone is open, see Force Zones on page 28) instead of Stay arm when a valid user access code with the Force Arming Option is entered. Regular Arming switches to Force Arming Section [704]: Arming/Disarming Options Option [1] OFF= Regular Arming Switches to Force Arming Disabled Option [1] ON= Regular Arming Switches to Force Arming Enabled (default) Stay Arming switches to Stay Force Arming Section [704]: Arming/Disarming Options Option [2] OFF= Stay Arming Switches to Stay Force Arming Disabled Option [2] ON= Stay Arming Switches to Stay Force Arming Enabled (default) Sleep Arming switches to Sleep Force Arming Section [704]: Arming/Disarming Options Option [3] OFF= Sleep Arming Switches to Sleep Force Arming Disabled Option [3] ON= Sleep Arming Switches to Sleep Force Arming Enabled (default) Restrict Arming on Battery Failure Section [703]: Arming/Disarming Options Option [5] OFF= Permit arming on battery failure (default) Option [5] ON= Restrict arming on battery failure Restrict Arming on Tamper Failure Section [703]: Arming/Disarming Options Option [6] OFF= Permit arming on tamper failure (default) Option [6] ON= Restrict arming on tamper failure With this feature enabled, the control panel will always Sleep Force arm (if a force-enabled zone is open, see Force Zones on page 28) instead of Sleep arm when a valid user access code with the Force Arming Option is entered. If this option is enabled, the control panel will not arm the system if the control panel detects that the backup battery is disconnected, that its fuse is blown, or that the battery voltage drops to less than 10.5V. The control panel will not arm the system until all battery trouble conditions are rectified. If this option is enabled, the control panel will not arm the system if the control panel detects a tamper trouble on one or more zones. The control panel will not arm the system until all tamper trouble conditions are rectified. WARNING: This feature will not function if the tamper recognition options (see Tamper Recognition on page 35) are disabled or whenever the tampered zone is bypassed and the tamper bypass options have been enabled (see Tamper Bypass Options on page 35). 32 MG5000+ / MG5050+ Installation Guide Restrict Arming on Wireless Supervision Trouble Section [703]: Arming/Disarming Options Option [7] OFF= Permit arming on wireless supervision failure (default) Option [7] ON= Restrict arming on wireless supervision failure If this option is enabled, the control panel will not arm the system if the control panel detects a wireless supervision trouble on one or more zones. The control panel will not arm the system until all wireless supervision trouble conditions are rectified. WARNING: This feature will not function if the tamper recognition options (see Tamper Recognition on page 35) are disabled or whenever the tampered zone is bypassed and the tamper bypass options have been enabled (see Tamper Bypass Options on page 35). Arm/Disarm with VDMP3 Section [703]: Arming/Disarming Options Option [8] OFF= Arm/Disarm with VDMP3 disabled Option [8] ON= Arm/Disarm with VDMP3 enabled (default) If this option is enabled, arming/disarming with the VDMP3 is functional. Disable the option if you do not want the ability to arm/disarm the system via telephone. Timed Auto-Arming Section [741] = Partition 1, [742] = Partition 2 Option [1] OFF= Timed Auto-Arming Disabled (default) Option [1] ON= Timed Auto-Arming Enabled Each partition can be programmed to arm every day at the time specified by the Auto-arm Timer. The auto-arming options (see Auto-Arming Options on page 33) determine the partition's arming method. Any open zones detected when a partition is auto-armed will be bypassed regardless of their definition (except 24Hr zones). The control panel will enter a 60-second exit delay period before arming the system. At this point, auto-arming can be cancelled by entering a valid access code. Once the partition has successfully armed, the control panel can transmit the Timed Auto-arming report code programmed in section [860]. Example: To automatically arm partition 2 everyday at 6:15PM, enable Timed Auto-arming for partition 2 by turning on option [1] in section [742]. Then key in 18:15 into section [762]. Auto-Arm Timer Section [761] = Partition 1, [762] = Partition 2 Select the section corresponding to the desired partition and program the time (use the 24-hour clock e.g., 6:30PM = 18:30) that you wish the control panel to attempt to arm the selected partition and/or send the Late to Close report code. No Movement Auto-Arming Section [741] = Partition 1, [742] = Partition 2 Option [2] OFF= No Movement Auto-Arming Disabled (default) Option [2] ON= No Movement Auto-Arming Enabled If no movement occurs in a partition's protected area for the period specified by the No Movement Timer, the control panel can automatically arm that partition. The Auto-arming Option determines the partition's arming method. Any open zones detected when a partition is Auto-armed will be bypassed regardless of their definition (except 24Hr zones). Upon arming, the control panel will transmit the No Movement report code if programmed in section [860]. Regardless of whether the system was successfully armed or not, the control panel will always transmit the No Movement report code if programmed in section [860]. If No Movement Auto-arming is disabled, the control panel will still send the No Movement report code at the time specified by the No Movement Timer. Example: To arm partition 1 whenever there is no movement for a period of 4 hours, enable No Movement Auto-arming for partition 1 by turning on the [2] Option in section [741]. Then in section [749] enter 016 (16x15min = 240min = 4 hours). No Movement Timer Section [749] = Partition 1, [750] = Partition 2 000 to 255 x 15 min, Default = Disabled Select the section corresponding to the desired partition and program the interval of time without movement you wish the control panel to wait before arming and/or sending the No Movement report code. If No Movement Auto-arming is disabled, the control panel can still send the No Movement report code when no movement has been detected for the period specified by the No Movement Timer. Auto-Arming Options Section [741] = Partition 1, [742] = Partition 2
[3]
OFF OFF ON
[4]
OFF ON OFF Regular Sleep Stay When using Timed Auto-arming or No Movement Auto-arming, the control panel can Regular, Sleep or Stay arm the selected partition. 33 MG5000+ / MG5050+ Installation Guide One-Touch Arming Section [703]: Options [1] to [3]
Option [1] ON = Press & hold the [ARM] key for One-touch Regular Arming. Option [2] ON = Press & hold the [STAY] key for One-touch Stay Arming. Option [3] ON = Press & hold the [SLEEP] key for One-touch Sleep Arming. The One-touch arming features allow users to arm the system without having to enter any access codes. To arm the system, press and hold the appropriate key (see above) for approximately 3 seconds. If the system is partitioned, you must also press the key corresponding to the partition you wish to arm. One-Touch Bypass Programming Section [703]: Options [4]
Option [4] ON = Press & hold the [BYP] key for One-touch Bypass Programming. Bypass programming allows users to program the alarm system to ignore (deactivate) specified zones the next time the system is armed. Press and hold the [BYP]
key for three seconds to access bypass programming mode. After entering the required arming sequence (e.g., user access code, etc.), the exit delay parameter determines the amount of time a user has to leave the protected area before the control panel arms the partition. The exit delay applies to all zones in the selected partition. When enabled, the keypad will beep once every second during the exit delay and will beep rapidly during the final 10 seconds of the exit delay. Exit Delay Section [745] = Partition 1, [746] = Partition 2 001 to 255 seconds, Default = 60 seconds Beep On Exit Delay Section [704]: Arming/Disarming Options Option [6] OFF= Beep on Exit Delay Disabled Option [6] ON= Beep on Exit Delay Enabled (default) Bell Squawk On Arm/Disarm with Keypad Section [704]: Arming/Disarming Options Option [5] OFF= Bell Squawk on Arm/Disarm Disabled (default) Option [5] ON= Bell Squawk on Arm/Disarm Enabled When this feature is enabled, the bell or siren will squawk once upon arming and twice upon disarming via the keypad. Bell Squawk On Arm/Disarm with Remote Control Section [704]: Arming/Disarming Options Option [4] OFF= Bell Squawk on Arm/Disarm with Remote Control Disabled (default) Option [4] ON= Bell Squawk on Arm/Disarm with Remote Control Enabled No Exit Delay When Arming with Remote Control Section [704]: Arming/Disarming Options Option [8] OFF= Provides Exit Delay When Arming with a Remote Control (default) Option [8] ON= No Exit Delay When Arming with a Remote Control When this feature is enabled, the bell or siren will squawk once upon arming with a remote control and twice upon disarming with a remote control. When the option is enabled, the panel cancels the exit delay (arms instantly) when a partition is armed with a remote control. When disabled, the exit delay timer will start when a partition is armed with a remote control. No Exit Delay Beeps and No Bell Squawk When Stay/Sleep Arming Section [704]: Arming/Disarming Options Option [7] OFF= No Exit Delay Beeps and No Bell Squawk When Stay/Sleep Arming Disabled Option [7] ON= No Exit Delay Beeps and No Bell Squawk When Stay/Sleep Arming Enabled (default) With this feature enabled, the control panel will prevent the bell or siren from squawking and the keypads from beeping during the exit delay, whenever a partition is Stay/Sleep armed. Exit Delay Termination Section [700]: Arming/Disarming Options Option [6] OFF= Exit Delay Termination (Disabled) Option [6] ON= Exit Delay Termination Enabled (default) When option [6] is enabled (ON), the panel will reduce the Exit Delay to 10 seconds when an Entry Delay zone is opened and closed during the Exit Delay. Example: 15 seconds into a 45 second Exit Delay, an Entry Delay zone opens and closes. The remaining 30 seconds is reduced to 10 seconds. Fast Exit When the system is already Stay or Sleep armed: This feature will allow you to exit and keep the system armed. Press and hold the [OFF] key for 3 seconds to start the exit delay. After the exit delay has elapsed, the system will switch to its previous arming mode. 34 MG5000+ / MG5050+ Installation Guide Alarm Options Bell Cut-Off Timer Section [747] = Partition 1, [748] = Partition 2 000 = Disabled, 001 to 255 minutes, Default = 4 minutes Recycle Alarm Delay Section [714]
000 = disabled, 001 to 255 minutes, Default = Disabled Recycle Alarm Counter Section [715]
000 = disabled, 001 to 255, Default = Disabled After an audible alarm, the bell or siren will stop upon disarming of the partition or when the Bell Cut-Off Timer has elapsed, whichever comes first. Recycle Alarm After the Bell Cut-Off Timer and the Recycle Delay have elapsed, the control panel will re-verify the zone status. If there are any open zones, the control panel will generate another alarm. In one armed period, the control panel will repeat this sequence the number of times defined by the Recycle Counter. The Recycle Delay determines the amount of time after Bell Cut-Off that the control panel will wait before re-verifying zone status. The Recycle Counter determines the number of times the control panel will re-verify the zone status after Bell Cut-Off in one armed period. Tamper Recognition Zones/RF Module and Keypad/Bus Module Tamper Recognition Section [705]: Tamper Recognition Options
[3]
OFF OFF ON
[4]
OFF ON OFF ON ON Zones/RF Module Tamper Recognition Options Disabled trouble only When disarmed: trouble only When armed: Follow zones alarm type When disarmed: audible alarm When armed: Follow zones alarm type trouble only audible alarm
* Tamper recognition of keypad/bus module only if section [700] option [7] is enabled. Keypad / Bus Module Tamper Recognition Options*
disabled trouble only If a device has been tampered with (e.g., the anti-tamper switch has been set off), the control panel can generate a trouble, an alarm, and/or transmit a report code to the monitoring station. The system will react to an RF zone and a keypad/bus module differently. RF Module Supervision Section [705]: Supervision Options
[6]
OFF OFF ON
[7]
OFF ON OFF ON ON RF Supervision Options Disabled trouble only When disarmed: trouble only When armed: Follow zones alarm type When disarmed: audible alarm When armed: Follow zones alarm type Keypad / Bus Module Supervision Options Disabled trouble only trouble only audible alarm The control panel waits for each of its assigned wireless transmitters to send a status signal within a specified time period to confirm their presence and functionality. If a device has not sent a signal within that time period, the control panel can generate a trouble, an alarm, and/or transmit a report code to the monitoring station. The system will react to an RF zone and a keypad/bus module differently. Tamper Bypass Options Section [705]: Zone Options Option [5] OFF= Tampers on bypassed zones will be ignored Option [5] ON= Will generate a tamper if detected on a bypassed zone (default) With option [5] off, the Tamper Recognition feature follows the zone bypass definition. This means the control panel will ignore any tampers detected on a bypassed zone. With option [5] on, Tamper Recognition ignores the bypass definition. This means the control panel will generate an incident as per Tamper Recognition settings if a tamper or wire fault occurs on a bypassed zone. Tamper Supervision on the Bus Module Section [700]: Supervision Options Option [7] OFF= Tamper supervision disabled (default) Option [7] ON= Tamper supervision enabled When the control panel detects a tamper on a bus module, the control panel can generate an alarm or trouble, unless the Tamper Supervision is disabled. 35 Tamper Supervision on Panel Section [700]: Supervision Options Option [8] OFF= Panel tamper supervision disabled Option [8] ON= Panel tamper supervision enabled (default) When the control panel detects a tamper, the control panel can generate an alarm or trouble, unless the Tamper Supervision is disabled. MG5000+ / MG5050+ Installation Guide Pressing the [1] and [3] keys simultaneously on the keypad for 3 seconds will generate a silent or audible alarm as defined by option [4]. Pressing the [4] and [6] keys simultaneously on the keypad for 3 seconds will generate a silent or audible alarm as defined by option [5]. Pressing the [7] and [9] keys simultaneously on the keypad for 3 seconds will generate a silent or audible alarm as defined by option [6]. Silent alarm:
The control panel emits a confirmation beep and transmits the appropriate Panic report code if programmed in section [863]. The control panel will not enable the keypad buzzers or the control panels BELL output (no audible alarm). Audible alarm:
Same as silent alarm, except the keypad buzzers and the BELL output will activate until a user cancels the alarm (disarms) with a valid user access code or when the Bell Cut-Off Timer elapses (see Bell Cut-Off Timer on page 35). Whether the system is partitioned or not, the control panel will report all panic alarms to partition 1. When a panic alarm is activated, the control panel can ignore the disarm signal from a remote control for a specified period. This prevents an aggressor from disarming the system by remote control during a panic situation. In section [718] enter a 3-digit value (000 to 255, 000 = disabled) representing the number of seconds that the remote controls will be locked out of the system. The Flex-Instant Delay is used to prevent false alarms when the premises is Stay/Sleep armed. In section [720] enter a 3-digit value (000 to 255, 000 = disabled) representing the number of seconds that the panel will delay an alarm allowing you to disarm the system (default 15 seconds). Keypad Panic Options Section [702]: General Options Option [1] OFF= Panic 1 Disabled (default) Option [1] ON = Panic 1 Enabled Option [2] OFF= Panic 2 Disabled (default) Option [2] ON = Panic 2 Enabled Option [3] OFF= Panic 3 Disabled (default) Option [3] ON = Panic 3 Enabled Option [4] OFF= Panic 1 is Silent (default) Option [4] ON = Panic 1 is Audible Option [5] OFF= Panic 2 is Silent (default) Option [5] ON = Panic 2 is Audible Option [6] OFF= Panic 3 is Silent (default) Option [6] ON = Panic 3 is Audible Panic Lockout Timer Section [718]
Flex-Instant Delay Section [720]
36 MG5000+ / MG5050+ Installation Guide Reporting and Dialer settings The following section explains all the features and options that must be programmed in order for your security system to properly report system events to a monitoring station. When an event (e.g. zone in alarm) occurs in the system, the control panel verifies if a report code was programmed in the section corresponding to the event (except Ademco Contact ID All Codes). If a report code was programmed, the control panel will dial the monitoring station telephone number defined by the Event Call Direction feature. When the monitoring station answers, the control panel will transmit the System Account Code, followed by the programmed report code. Zone Reporting Codes Sections [141] to [172]
A report code can be programmed for each of the available 32 zones. When an alarm, alarm restore, tamper, or tamper restore occurs on a zone, the control panel can send the appropriate report code to the monitoring station. User Reporting Codes Sections [471] to [502]
A report code can be programmed for each of the available 32 users. When a user arms, disarms or cancels an alarm, the control panel can send the appropriate report code to the monitoring station. Special Arming Report Codes Sections [860] and [861]
When the system is armed using one of the special arming features listed below, the control panel can send the appropriate report code to the monitoring station identifying how the system was armed. Section [860]
Section [861]
Section [863]
Section [864]
Auto-Arming: A partition has armed itself at the programmed time. Late to Close: Reports every day at the time specified by the Auto-arm Timer. No Movement: No movement has been detected for the programmed amount of time in the partition. Partial Arming: A partition was Stay, Sleep, or Force armed or armed with Bypassed zones. Quick Arming: A partition was armed using a One-touch arming feature. Arming via PC: A partition was armed using the BabyWare software. N/A N/A Special Disarming Report Codes Section [862]
When using one of the special disarming features, the control panel can send the report code to the monitoring station, identifying how the system was disarmed. Cancel Auto-Arm: A partition is disarmed during the Timed Auto-arm's 60-second exit delay. Only reports if Disarming Reporting Options are set to always report disarming. Disarming via PC: System is disarmed using the BabyWare software. Only reports if Disarming Reporting Options are set to always report disarming. Cancel alarm with user or BabyWare: An alarm is canceled using the BabyWare software. Cancel Paramedic Alarm: A paramedic alarm is canceled. Special Alarm Report Codes Sections [863] and [864]
When the system generates an alarm due to one of the conditions listed below, the control panel can send the appropriate report code to the monitoring station identifying the type of alarm. Emergency Panic: Panic keys [1] and [3] have been pressed. Auxiliary Panic: Panic keys [4] and [6] have been pressed. Fire Panic: Panic keys [7] and [9] have been pressed. Recent Closing: Reports when an alarm is generated after arming the system within period defined by the Recent Close Delay. Zone Shutdown: A zone communicates more than the programmed number of transmissions in a single armed period. Duress: A Duress access code is keyed in. Keypad Lockout: If a consecutive number of invalid codes are entered into a keypad, the control panel can be set to deny access from all keypads for a specified period. Paramedic Alarm: A parademic alarm is sent to the monitoring station. 37 System Trouble Report Codes Section [865] to [869]
When the system generates one of the instances listed below, the control panel can send the appropriate report code to the monitoring station identifying the type of system trouble. MG5000+ / MG5050+ Installation Guide Section [865]
N/A AC Failure: The control panel has detected a loss of AC power. Transmission of this report code can be delayed. Battery Failure: Backup battery is disconnected or battery voltage is low. Auxiliary Supply: Auxiliary power supply has overloaded. Bell Output Overload: Bell/siren output has overloaded. Bell Output Disconnected: Devices connected to the Bell Output have been disconnected. Timer Loss: The control panel has detected a loss in time or clock failure. Fire Loop Trouble: The control panel has detected a tamper trouble on a fire zone. Fail To Communicate: The control panel has failed all attempts to communicate with the monitoring station. The report code will be transmitted upon the next successful attempt. RF Interference: Will report if the RF signal is being jammed. Module Lost: The control panel has failed to communicate with one or more modules (including keypads). Module Tamper: The anti-tamper switch of a module (including keypads) has been triggered. Module AC Fail: The AC voltage of a module has dropped below recommended limits. Module Low/No Battery: The battery voltage of a module has dropped below recommended limits. Wireless Zone Low Battery: The battery voltage of a wireless transmitter has dropped below recommended limits. Wireless Zone Supervision Lost: The control panel has lost communication with a wireless zone. Wireless PGM Supervision Lost: The control panel has lost communication with a wireless PGM. Wireless PGM Tamper: The anti-tamper switch of a wireless PGM has been triggered. N/A N/A System Trouble Restore Report Codes Sections [870] to [874]
When the system restores one of the troubles listed in System Trouble Report Codes above, the control panel can send the appropriate report code to the monitoring station identifying the type of system trouble restore. If Telephone Line Monitoring is enabled, the control panel can also transmit a TLM Restore report code. System Special Report Codes Sections [875] to [876]
When the system generates one of the instances listed below, the control panel can send the appropriate report code to the monitoring station identifying the type of system occurrence. Cold Start: The control panel was completely shutdown (no battery, no AC) and then was re-started. Test Report: A test report has been generated automatically. BabyWare In: The control panel has commenced communication with BabyWare. BabyWare Out: The control panel has ended communication with BabyWare. Installer In: Installer/Maintenance has entered the programming mode. Installer Out: Installer has exited the programming mode. Closing Delinquency: The control panel will send a Closing Delinquency report code if the system has not been armed within a programmed amount of days. N/A Section [866]
Section [867]
Section [868]
Section [869]
Section [875]
Section [876]
38 Enable all options you want to clear. The respective sets of reporting codes will be cleared after exiting the section. MG5000+ / MG5050+ Installation Guide Clear Reporting Codes Section [966]: Clear Reporting Codes Option [1] OFF= Clear zone reporting codes Option [1] ON= Clear zone reporting codes (default) Option [2] OFF= Clear user reporting codes Option [2] ON= Clear user reporting codes (default) Option [3] OFF= Clear arm/disarm/alarm reporting codes Option [3] ON= Clear arm/disarm/alarm reporting codes (default) Option [4] OFF= Clear trouble reporting codes Option [4] ON= Clear trouble reporting codes (default) Reset Reporting Codes Section [967]: Reset Reporting Codes Option [1] OFF= Reset zone reporting codes Option [1] ON= Reset zone reporting codes (default) Option [2] OFF= Reset user reporting codes Option [2] ON= Reset user reporting codes (default) Option [3] OFF= Reset arm/disarm/alarm reporting codes Option [3] ON= Reset arm/disarm/alarm reporting codes (default) Option [4] OFF= Reset trouble reporting codes Option [4] ON= Reset trouble reporting codes (default) Press
[OFF]
[BYP]
[MEM]
[TBL]
[SLEEP]
Action or Value
4-second pause deletes current digit inserts blank space switch from pulse to tone dialing or vice versa Enable all options you want to reset to default. The respective sets of reporting codes will be reset after exiting the section. Monitoring Station Telephone Numbers Section [815] = Phone#1, [816] = Phone#2, [817] = Backup Phone#, [818] = Pager #, [819] = Numeric Message Sent with Pager Reporting: Up to 32 digits The control panel can dial up to 2 different monitoring station telephone numbers. You can enter any digit from 0 to 9 and any special keys or functions up to a maximum of 32 digits. After the maximum dialing attempts (see Maximum Dialing Attempts on page 41) to one monitoring station telephone number have failed, the control panel will then dial the backup telephone number. If the Alternate Dial Option (see Alternate Dial Option on page 41) is enabled, the control panel will dial the programmed backup telephone number after every failed attempt. If no backup telephone number is programmed, the control panel will never report to the backup telephone number. Also see Delay Between Dialing Attempts on page 41. Personal Dialing Numbers Personal Dialing numbers are personal numbers (e.g. cellular, office) that the panel can call in case of an alarm or panic. To program these five numbers see the Communicator Menu in either the Master or User Quick Menu. To set the call parameters, see options [5], [6], and [7] of section [804]. The panel will call these personal numbers if programmed in the event of any panic or alarm (default) and sound a bell tone. To program the delay between the call attempts, see section [832]. The panel can also be programmed to delay before sounding the bell tone, which can be programmed in section [836]. The default delay is 20 seconds. To determine the length of time the bell tone sounds on the phone line, see section [837]. The default value is 003, meaning the 10 second bell tone will repeat itself 3 times after the initial sequence (total= 40 seconds). 39 Reporting Formats Section [810]: 1st digit = Format for Phone #1, 2nd digit = Format for Phone #2 The panel can use a number of different reporting formats and each monitoring station telephone number can be programmed with a different reporting format. The first digit entered into section [810] represents the reporting format used to communicate with Monitoring Station Telephone Number 1, the second digit represents the reporting format used to communicate with Monitoring Station Telephone Number 2. The Backup Telephone Number uses the same reporting format as the last monitoring station telephone number that was dialed. MG5000+ / MG5050+ Installation Guide Value Entered 0 1 2 3 4 5 Reporting Format Ademco Slow (1400Hz, 1900Hz, 10BPS) Silent Knight Fast (1400Hz, 1900Hz, 10BPS) SESCOA (2300Hz, 1800Hz, 20BPS) Ademco Express (DTMF 4+2) Ademco Contact ID SIA If Hexadecimals (0 to FF) are used to program the report codes, verify that the pager also supports Hexadecimals. If the pager does not support Hexadecimals, use only the digits 0 to 9. Standard Pulse Formats The control panel can use the Ademco slow, Silent Knight and Sescoa standard pulse reporting formats which will transmit the 2-digit (00 to FF) report codes programmed into sections [860] to [876]. Ademco Express The Ademco Express is a high-speed reporting format, which will transmit the 2-digit (00 to FF) report codes programmed into sections [860] to [876]. Ademco Contact ID Ademco Contact ID is a fast communicator format that uses tone reporting instead of pulse reporting. This communicator format also uses a pre-defined list of industry standard messages and report codes that will suit most of your basic installation needs. Please refer to the Contact ID Report Codes List in the Programming Guide for a complete list of these report codes and messages. If the reporting codes are set at 0xFF, the panel will send the appropriate report code from the Automatic Report Code List in the programming guide. Alternatively, report codes can be programmed using the Ademco Contact ID Report Codes in the programming guide. Event Call Direction Section [802]: Options [1] to [3]; Arming/Disarming Option [1] ON =Call MSTN 1 Option [2] ON =Call MSTN 2 Option [3] ON =Call Pager telephone number Section [802]: Options [5] to [7]; Alarm/Alarm Restore Option [5] ON =Call MSTN 1 Option [6] ON =Call MSTN 2 Option [7] ON =Call Pager telephone number Section [803]: Options [1] to [3]; Tamper/Tamper Restore Option [1] ON =Call MSTN 1 Option [2] ON =Call MSTN 2 Option [3] ON =Call Pager telephone number Section [803]: Options [5] to [7]; Trouble/Trouble Restore Option [5] ON =Call MSTN 1 Option [6] ON =Call MSTN 2 Option [7] ON =Call Pager telephone number Section [804]: Options [1] to [3]; Special Reporting Option [1] ON =Call MSTN 1 Option [2] ON =Call MSTN 2 Option [3] ON =Call Pager telephone number Section [804]: Options [5] to [7]; Special Reporting Option [1] ON =Call voice on zone alarm (burglary/fire) Option [2] ON =Call voice on panic alarms Option [3] ON =Call voice on paramedic alarm The events are divided into six groups (see above) where each event group can be programmed to dial up to three telephone numbers (MSTN 1 & 2 and the Pager telephone number). When a reportable event occurs in the system, the panel will begin dialing the numbers sequentially starting from MSTN 1 (if enabled), skipping any disabled numbers and stopping once all selected telephone numbers have been called. After a certain amount of failed attempts (section [831]) at trying to call the monitoring station, the control panel will then dial the selected backup telephone number (if enabled; see Programming Guide). If the Alternate Dial option is enabled, the control panel will dial the programmed backup telephone number (if enabled) after every failed attempt. If no backup telephone number is programmed, the control panel will never report to the backup telephone number. 40 Example: The system is armed and zone 1 has been breached causing an alarm. If options [5] and [7] are OFF and option [6] is ON in section [802], the control panel will attempt to communicate with MSTN 2. All report codes are preceded by a 4-digit or 3-digit Partition Account Number to ensure correct identification in a partitioned system. Partition account numbers can be any hexa-digit from 1 to F. To enter a 3-digit account number, simply press the [SLEEP] key followed by a 3-digit account number. Also, when using 3-digit account numbers, you must use 1-digit report codes. MG5000+ / MG5050+ Installation Guide Account Numbers Section [811]: Partition 1, Section [812]: Partition 2 Dialing Method Section [800]: Dialer Options Option [6] OFF= Pulse Dialing (see Pulse Ratio on page 41). Option [6] ON= Tone/DTMF Dialing (default) Pulse Ratio Section [800]: Dialer Options Option [7] OFF= European Pulse Ratio of 1:2 Option [7] ON= U.S.A. Pulse Ratio of 1:1.5 (default) Maximum Dialing Attempts Section [831]
000 to 255 attempts, Default = 8 attempts Maximum Dialing Attempts - VDMP3 Section [841]
000 to 255 attempts, Default = 8 attempts Delay Between Dialing Attempts Section [832]
000 to 255 seconds, Default = 20 seconds Alternate Dial Option Section [800]: Dialer Options Option [4] OFF= Alternate Dial Disabled (default) Option [4] ON= Alternate Dial Enabled Force Dial Option Section [800]: Dialer Options Option [5] OFF= Force Dial Disabled Option [5] ON= Force Dial Enabled (default) When using Pulse dialing, you can select one of two Pulse Ratios. Although most European countries use the 1:2 pulse ratio, the 1:1.5 ratio may provide better results in some cases. The same applies for North American countries. If the 1:1.5 pulse ratio is not providing the desired results, the 1:2 ratio may be used. The value programmed in section [081] determines how many times the control panel will re-dial the same monitoring station telephone number before proceeding to the next number. The value programmed in section [841] determines how many times the control panel will re-dial the same telephone number before proceeding to the next number. The maximum dialing attempts programmed in this section is independent from those programmed in section [831] of the panel dialer used for monitoring station reporting. This delay determines the amount of time the control panel will wait between each dialing attempt. This section applies to the Plug-in Voice Dialer when using a VDMP3. Switch to Pulse on 5th Attempt Section [800]
Option [3] OFF= Switch to Pulse on 5th Attempt Disabled (default) Option [3] ON= Switch to Pulse on 5th Attempt Enabled With option [3] ON, the control panel will switch to pulse dialing on the 5th attempt of reaching the monitoring station. With option [4] OFF, the control panel will dial the backup programmed in section [817] after all attempts to one monitoring station number have failed. With option [4] ON, the control panel will dial the backup number after every failed attempt. With option [5] is enabled, the panel will dial a telephone number even if no dial tone is present after 4 seconds. 41 MG5000+ / MG5050+ Installation Guide Recent Closing Delay Section [838]
000 = Disabled, 001 to 255 seconds, Default = Disabled If after having armed the system, an alarm is generated within the period defined by the Recent Close Delay, the control panel will attempt to transmit the Recent Close report code programmed in section [863]. Auto Test Report Sections [840]
000 = Disabled, 001 to 255 days, Default = Disabled Section [850]: Time (HH:MM) The control panel will transmit the Test Report report code programmed into section [875] after the number of days programmed into section [840] has elapsed at the time programmed into section [850]. Use the 24-hour clock to program the time (e.g., 6:30PM = 18:30). The first Test Report will be transmitted within 24 hours after the feature is enabled at the time programmed in [850]. Example: Section [840] = 005 and section [850] = 13:00. The first Test Report will be sent at 1 PM that day and then the report will be sent every 5 days at 1 PM. Auto Test Report Transmission Options Sections [800]
[3]
[4]
Auto-Test Report Transmission Options OFF OFF Transmit the test report code every time the days programmed in section [840] have elapsed at the time pro-
grammed in section [850] (default). OFF ON When disarmed: Transmit test report code every time the time programmed in section [852] has elapsed. When armed: Transmit test report code every time the time programmed in section [851] has elapsed. ON OFF The control panel will transmit the test report code every hour on the minute value programmed in section [850]
(the last two digits). Note that the first two digits of section [850] will be ignored. E.g. If 10:25 was programmed into section [850], the test report code would be transmitted at the 25th minute of every hour, e.g., 11:25, 12:25, etc. ON ON The test report code will be transmitted when any of the conditions of the second and third options listed above
(options [3] = OFF and [4] = ON / options [3] = ON and [4] = OFF) are met. The Armed Report Delay determines the amount of time after an Arming event that the control panel will wait before sending a report. The Disarmed Report Delay determines the amount of time after an Disarming event that the control panel will wait before sending a report. At midnight every day, the control panel will verify when the partition was last disarmed. If the partition has not been armed within the time programmed in the Closing Delinquency Delay, the control panel will transmit a Closing Delinquency event to the monitoring station. Example: The Closing Delinquency Timer for partition 1 in section [719] is programmed for 005 days. The control panel verifies when partition 1 was last disarmed at midnight every day. If partition 1 was not armed within the last 5 days, the panel will transmit a Closing Delinquency event to the monitoring station. The Closing Delinquency Event and timer apply only to partition 1. The control panel will transmit the AC Failure report code programmed in section [865] after the Power Failure Report Delay period has elapsed. Armed Report Delay Section [851]
000 = disabled, 001 to 255 minutes, Default = 5 min. Disarmed Report Delay Section [852]
000 = disabled, 001 to 255 minutes, Default = 60 min. Closing Delinquency Delay Section [719]
000 = Disabled, 001 to 255 days, Default = Disabled Power Failure Report Delay Section [839]
001 to 255 minutes, Default = 15 minutes Report System Disarming Section [801]: Arming /Disarming Options Option [1] OFF= Always Report Disarming Option [1] ON= Report Disarming Only After Alarm (default) 42 With option [1] OFF, the control panel will send the Disarming report codes (see Special Disarming Report Codes on page 37) to the monitoring station every time the system is disarmed. With option [1] ON, the control panel will send the Disarming report codes to the monitoring station when the system is disarmed following an alarm. MG5000+ / MG5050+ Installation Guide Zone Restore Report Options Section [801]: Zone Options Option [2] OFF= Report On Bell Cut-Off (default) Option [2] ON= Report On Zone Closure With option [2] OFF, the panel will send the Zone Alarm Restore report codes to the monitoring station when the zone has returned to normal and the Bell Cut-Off Timer has elapsed. With option [2] ON, the panel will send the Zone Alarm Restore report codes to the monitoring station as soon as the zone returns to normal or when the system is disarmed. Telephone Line Monitoring (TLM) When enabled, the system verifies the existence of a telephone line once every second. A line test failure occurs when the TLM detects less than 3 volts for the period defined by the TLM Fail Timer. If the line test fails, the control panels STATUS LED flashes and generates one or more conditions as defined by the TLM settings below. These will be restored when the control panel detects the telephone line again. Please note that when the dialer detects an incoming call, the TLM test will stop for 1 minute. Section [800]: Dialer Options
[1] OFF / [2] OFF: TLM Disabled
[1] OFF / [2] ON: Trouble Only Upon line test failure, a TLM Trouble will appear in the keypads trouble display (see Trouble Display on page 51).
[1] ON / [2] OFF: Audible Alarm If System Armed Upon line test failure, a TLM Trouble will appear in the keypads trouble display (see Trouble Display on page 51) and if the system is armed, the control panel will generate an audible alarm.
[1] ON / [2] ON: Silent Alarm Becomes Audible Upon line test failure, a TLM Trouble will appear in the keypads trouble display (see Trouble Display on page 51) and causes a silent zone or silent panic alarm to switch to audible. If TLM does not detect the existence of a telephone line for the duration of this period, the control panel will generate the condition(s) defined by the TLM options. TLM Fail Timer Section [830]
016 to 255 x 2 seconds, Default = 32 seconds Pager Reporting Delay Section [834]: Communication Timers 000 to 255 seconds, Default = 20 seconds Pager Reporting Message Repetition Section [835]: Communication Timers 000 to 255 times, Max. 10, Default = 3 Personal Reporting Delay Section [836]: Communication Timers 000 to 255 times, Max. 127, Default = 5 Personal Reporting Message Repetition Section [837]: Communication Timers 000 to 255 times, Max. 10, Default = 3 Disable Reporting Sections [800]
Option [1] OFF= Dialer Activated (default) Option [1] ON= No Dialer When using the Pager Reporting Format, the control panel will wait for the Pager Delay period before transmitting the report codes. This is to allow time for the pager system to provide a dial tone or to bypass the welcome message before sending data. When using the Pager Reporting Format, the control panel will repeatedly send the report codes to the pager until the transmission has been acknowledged. When using the Personal Reporting Format, the control panel will wait for the Personal Delay period before transmitting the report codes. This is to allow time for the system to provide a dial tone or to bypass the welcome message before sending data. This section applies to the Plug-in Voice Dialer when using a VDMP3. When using the Personal Reporting Format, the control panel will repeatedly send the report codes to the pager until the transmission has been acknowledged. This section applies to the Plug-in Voice Dialer when using a VDMP3. With this option disabled (default), the control panel will continue to report events. With the option enabled, reporting is disabled. 43 MG5000+ / MG5050+ Installation Guide Programmable Outputs PGM is a programmable output that toggles to its opposite state (e.g., a normally open PGM will close) when a specific event has occurred in the system. For example, a PGM can be used to activate bells or strobe lights, open/close garage doors and much more. When a PGM activates, the control panel triggers any device or relay connected to it. The control panel includes two/four onboard PGMs. It can support up to a total of 16 PGMs. A Wireless PGM module can be assigned to any PGM. It will work in parallel with the Control Panel Output. PGM Activation Event Sections [220], [222], [224], [226], [228], [230], [232], [234], [236], [238], [240], [242], [244], [246], [248], and [250]
This feature allows you to program the control panel to activate a PGM when a specific event occurs in the system. The PGM will remain in its active state until the programmed PGM Deactivation Event occurs or when the PGM Delay period elapses. For the Event List see the programming guide. To program a PGM Activation Event:
1. 2. 3. 4. Enter section that represents the desired PGM. PGM1 = [220], PGM2 = [222], etc. Enter the Event Group #. Enter the Sub-Group #. Enter the Partition # (01 = Partition 102 = Partition 299 = Both Partitions) WARNING: The AC Loss PGM Event will only occur after the power failure report delay elapses (see Power Failure Report Delay on page 42). PGM Deactivation Event Sections [221], [223], [225], [227], [229], [231], [233], [235], [237], [239], [241], [243], [245], [247], [249], and [251]
After PGM activation, the PGM will return to its normal state (deactivate) when the programmed PGM Deactivation Event occurs. Instead of deactivating the PGM when a specific event occurs, the PGM can deactivate after a programmed period elapses (see PGM Delay on page 44). For the Event List see the Programming Guide. If using the PGM Delay, these sections can be used as a second activation event. Instead of deactivating the PGM on the occurrence of a specific event, the PGM will deactivate after the period programmed here has elapsed. NOTE: If a PGM Delay is programmed, the deactivation event can be used as a second activation event. 1. 2. 3. 4. Enter section that represents the desired PGM. PGM1 = [221], PGM2 = [223], etc. Enter the Event Group #. Enter the Sub-Group #. Enter the Partition # (01 = Partition 102 = Partition 299 = Both Partitions) PGM Delay Section [281] = PGM 1 to [296] = PGM 16, 001 to 255 sec./min., 000 = Follows Deactivation Event, Default = 5 seconds PGM Options Section [261] to [276]: PGM Options Option [1] OFF= PGM Base Time in Seconds (default) Option [1] ON = PGM Base Time in Minutes This option sets the PGM delay in increments of minutes or seconds. Option [2] OFF= PGM State Normally Open (N.O.) (default) Option [2] ON = PGM State Normally Closed (N.C.) Option [3] OFF= PGM Supervision Disabled Option [3] ON = PGM Supervision Enabled (default) Option [4] OFF= PGM Activation Mode Steady (default) Option [4] ON = PGM Activation Mode Pulse This option sets the PGM to be either steady (ON), or pulsed (ON/OFF) when it is activated. Option [5] OFF= PGM Pulse once every 30 seconds disabled (default) Option [5] ON= PGM Pulse once every 30 seconds enabled 44 If enabled, the panel can wait for each of its assigned wireless transmitters to send a status signal within a specified time to confirm their presence and functionality. Program PGMs to pulse during an alarm for either partition. With this feature enabled, and in combination with the Follow Arm/Stay Arm/Sleep Arm PGM type, the PGM will mimic the Arm LED. MG5000+ / MG5050+ Installation Guide When armed, the PGM will pulse once every 30 seconds. Option [6] OFF= PGM Pulse on any alarm disabled (default) Option [6] ON= PGM Pulse on any alarm enabled This option sets the PGMs to pulse on any alarm. Option [7] OFF= PGM Pulse on any alarm Partition 1(default) Option [7] ON= PGM Pulse on any alarm Partition 2 PGM Programming Sections [301] to [316]
The programming of the PGMs is accomplished in two steps:
1. Assign the PGMs to the panel. 2. Program the PGMs. PGM Programming can be executed through the Installer Quick Menu in the programming guide. How Do I Assign PGMs to the Panel?
1. 2. 3. 4. Press the [ENTER] key. Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default) Enter the desired [SECTION NUMBER] (from sections [301] to [316]). Enter the 6-digit [SERIAL NUMBER] of the PGM. How Do I Delete Assigned PGMs?
1. 2. 3. 4. Press the [ENTER] key. Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111) Enter the desired [SECTION NUMBER] (from sections [301] to [316]). Press the [0] key six times to clear the serial number. 45 MG5000+ / MG5050+ Installation Guide System Settings Version Number Display Enter section [980] to view the version number of the panel. The first digit will appear. Press [ENTER] to scroll through each consecutive digit (the keypad will beep twice after every digit in the version number). Once the version number has been fully displayed, an acknowledgment beep (3 beeps) will sound and the first digit will be displayed again. Push Button Power Reset Performing a hardware reset will set all control panel settings to factory default except for the Panel ID and PC Password. Also, the event buffer will not be erased. To perform a push button power reset:
Press and hold the RESET switch for five seconds. The STATUS LED will start flashing fast. Within 2 seconds of this flashing, press the reset switch again. The panel will reset to default and restart Installer Lock Section [395]
000 = Disabled, 147 = Lock Enabled, Default = Disabled Program 147 into section [395] to lock all programming. Performing a hardware reset will not affect the current panel settings. To remove the Installer Lock, enter 000. Please note that three seconds after turning on the control panel the STATUS LED and the relay on the control panel will flash fast for 6 seconds to indicate that the installer lock is enabled. Once enabled, the panel cannot be reset. Keypad Lockout Feature Sections [864]
If a consecutive number of invalid codes are entered into a keypad, the control panel can be set to deny access from all keypads for a specified period and send the report code programmed in section [864]. Program the number of consecutive invalid codes from 001 to 255 (000 = disabled) into section [717]. Program the duration of the Keypad Lockout from 001 to 255 minutes into section [716]. Partitioning Section [700]: General Options Option [1] OFF= Partitioning Disabled (default) Option [1] ON= Partitioning Enabled The panel is equipped with a partitioning feature which can divide the alarm system into two distinct areas identified as Partition 1 and Partition 2. Partitioning can be used in installations where shared security systems are more practical, such as an office/warehouse building. When partitioned, each zone, each user code (see Access Codes on page 20) and some of the system's features can be assigned to Partition 1, Partition 2 or both. If the system is not partitioned, all user codes and features will be recognized as belonging to Partition 1. Users can only arm partitions to which they have been assigned. Only zones assigned to Partition 1 will arm/disarm when Partition 1 is armed or disarmed. Only zones assigned to Partition 2 will arm/disarm when Partition 2 is armed or disarmed. Zones assigned to both partitions will arm when both partitions are armed and will disarm when at least one disarms. The following features can be programmed separately for each partition: Entry/Exit Delay Timer, Auto-arming Options, Bell Cut-Off Timer, Switch to Stay arming, PGM Events and Account Numbers. WARNING: If the system is not partitioned, all zones, user codes, and features will be recognized as belonging to partition 1. Zones that have been manually assigned to partition 2 will no longer function. Confidential Mode Section [701] Options [3], [4] and [5]
Option [3] OFF= Confidential Mode Disabled (default) Option [3] ON= Confidential Mode Enabled Option [4] OFF= Keypads activate when an access code is entered (default) Option [4] ON= Keypads activate when a key is pressed Option [5] OFF= Confidential Mode Timer is 2 minutes (default) Option [5] ON= Confidential Mode Timer is 5 seconds Installer Function Keys To access the Installer Function keys, press:
46 If Confidential Mode is enabled and no actions are performed on the keypads for the time defined by the Confidential Mode Timer, all the keypads LEDs will be off until either a key is pressed or an access code is entered. When the system exits Confidential Mode, the keypads will display the systems status. Confidential Mode is activated by enabling option [3]. Option [4] regulates whether the keypads will be activated at the touch of a key or only when an access code is entered. Option [5]
determines the amount of time without action before the system enters Confidential Mode (5 seconds or 2 minutes). MG5000+ / MG5050+ Installation Guide
[ENTER]+[INSTALLER CODE]+[MEM] = Test Report: Send the Test Report report code programmed in section [875] to the monitoring station.
[ENTER]+[INSTALLER CODE]+[STAY] = Cancel Communication: Cancels all communication with BabyWare software or with the monitoring station until the next reportable event.
[ENTER]+[INSTALLER CODE]+[SLEEP] = Answer BabyWare Software: Will force the console to answer an incoming call from the monitoring station that is using the BabyWare software.
[ENTER]+[INSTALLER CODE]+[BYP] = Call BabyWare Software: Will dial the PC telephone number programmed in section [915] in order to initiate communication with a computer using the BabyWare software.
[ENTER]+[INSTALLER CODE]+[TBL] = Installer Test Mode: The installer test mode will allow you to perform walk tests where the siren will squawk to indicate opened zones. Press the [TBL] key again to exit. Daylight Savings Time Section [730]: General Zone Options 2 Option [1] OFF= Daylight Savings Time Disabled (default) Option [1] ON= Daylight Savings Time Enabled With section [730] option [1] ON, the panel adjusts the systems clock (time) for daylight savings changes. At 2:00AM on the second Sunday of a full weekend in March, the control panel will add one hour to the programmed time (clock). At 2:00 AM on the first Sunday of a full weekend in November, the control panel will subtract one hour from the programmed time (clock). By default, when section [730] is set at 18, the time is set for the US, Canada etc. For other countries see Daylight Savings Programming in the programming guide and set the country code in section [731]. Country Code List (Default = bold) 00 = US, Canada, Mexico, St.Johns, Bahamas, Turks and Caicos 01 = Cuba 02 = Brazil 03 = Chile 04 = Falklands 05 = Paraguay 06 = European Union, UK, and Greenland 07 = Russia and most states of the former USSR 08 = Australia- South Australia, Victoria, Australian Capital Territory, New South Wales 09 = Lord Howe Island- Tasmania 10 = New Zealand, Chatham 11 = Tonga 12 = Iraq and Syria 13 = Israel 14 = Lebanon, Kirgizstan 15 = Palestine 16 = Egypt 17 = Namibia 18 = USA, Canada (New Daylight Saving Time for 2007 onward) 19 = New Zealand (New Daylight Saving Time for 2007 onward) Customized Daylight Saving Programming In addition to using the default Daylight Saving Time (DST) settings in section [731], you can also set a customized DST. Set section [732] for the DST starting period and [733] for the DST ending period. Both sections recognize 5 different entries of 2 digits each. All entries must be assigned in this respective order:
01 to 12 01 to 31 00 to 07 00 to 23 00 to 59 01 = January 01 = First day of the month 00 = Default*, 01 = Sunday 00 = Midnight 00 = 60 minutes or 1 hour
*If the day is set at 00, the DST will automatically change on the pro-
grammed country code listed above. Months Date Day Hours Minutes
[732]
[733]
Section Data Description __/__/__/__/__/__/__/__/__/__/
Daylight Savings Time Starting Period __/__/__/__/__/__/__/__/__/__/
Daylight Savings Time Ending Period Audible Trouble Warning Except AC Failure Section [700]: General System Options Option [3] OFF= Audible trouble warning except AC failure (default) Option [3] ON= Audible trouble warning except AC failure When this option is enabled the panel will generate an audible trouble warning on all troubles except AC failure. Audible Trouble Warning on AC Failure Section [700]: General System Options Option [4] OFF= Audible trouble warning on AC failure (default) Option [4] ON= Audible trouble warning on AC failure When this option is enabled the panel will generate an audible trouble warning in the event of an AC failure. Display Entry Delay on LCD keypad (K32LCD+) Section [701]: General System Options 47 MG5000+ / MG5050+ Installation Guide Option [7] OFF= Display entry delay on LCD keypad Option [7] ON= Display entry delay on LCD keypad (default) When this option is enabled the panel will display entry delays on the K32LCD+ keypad modules. Display Exit Delay on LCD keypad (K32LCD+) Section [701]: General System Options Option [8] OFF= Display exit delay on LCD keypad Option [8] ON= Display exit delay on LCD keypad (default) When this option is enabled the panel will display exit delays on the K32LCD+ keypad modules. 48 MG5000+ / MG5050+ Installation Guide Settings for BabyWare Software Panel Answer Options The following two options define how the control panel answers an incoming call from a computer using the BabyWare Software for Windows. Answering Machine Override Delay Section [902]
000 = Disabled, 000 to 255 seconds, Default = 030 When using the BabyWare software to communicate with an installation site that uses an answering machine or service, the answering machine override must be programmed. Using the BabyWare software you will call the control panel, hang up, then call back. If the installation site is called back within the programmed delay period, the control panel will override the answering machine or service by picking-up the line after the first ring on the second call. You must wait at least 10 seconds before attempting the second call, otherwise, the control panel will think it is the same call. For details on how to use the BabyWare software, refer to the BabyWare Help Manual. This section applies to the Plug-in Voice Dialer when using a VDMP3. Example: A security installation is using an answering machine set to answer after three rings. If section [902] has been programmed with 040 (40 seconds) and the second call is made within 40 seconds, the control panel will pick up the line on the first ring. If it takes more than 40 seconds, the control panel will not answer on the first ring and the answering machine will answer after three rings. Number of Rings Section [901]
000 = disabled, 001 to 015 rings, Default = 8 rings This value represents the number of rings the control panel will wait before picking-up the line. If the line is not answered after the number of programmed rings, the control panel will answer the call. This section applies to the Plug-in Voice Dialer when using a VDMP3. This 4-digit code identifies the control panel to the BabyWare software before initiating communication. The control panel will verify that the Panel Identifier in the BabyWare software is the same. If the codes do not match, the control panel will not establish communication. Therefore, be sure to program the same panel identifier into both the control panel and the BabyWare software. This 4-digit password identifies the PC to the panel before establishing communication. Program the same PC Password into both the control panel and the BabyWare software. If the passwords do not match, the BabyWare software will not establish communication. The control panel will dial this number when trying to initiate communication with a computer using the BabyWare software. You can enter any digit from 0 to 9 and any special keys or functions up to a maximum of 32 digits. The control panel will dial the PC Telephone Number programmed in section [915] in order to communicate with the BabyWare software. The control panel and the BabyWare software will verify that the Panel Identifier and the PC Password match before establishing communication. Panel Identifier Section [910]
0000 to FFFF PC Password Section [911]
0000 to FFFF PC Telephone Number Section [915]
Up to 32 digits Call BabyWare Software
[ENTER]+ [INSTALLER CODE] + [BYP]
Answer BabyWare Software
[ENTER] + [INSTALLER CODE] + [SLEEP]
In order to perform on-site upload/download connect your computer directly to the control panel using an ADP-1 line adapter. In the BabyWare software set Dialing Method to Blind Dial. Program the panel telephone number in BabyWare software and follow the instructions on the ADP-1 adapter. When the computer has dialed, press [ENTER] followed by the Installer/Maintenance Code, then press the [SLEEP] key to manually answer the BabyWare software from the control panel. 49 MG5000+ / MG5050+ Installation Guide Automatic Event Buffer Transmission Section [900]: Dialer Options Option [2] OFF= Auto Event Buffer Transmission Disabled (default) Option [2] ON= Auto Event Buffer Transmission Enabled Call Back BabyWare Section [900]: Dialer Options Option [1] OFF= Call Back BabyWare Disabled (default) Option [1] ON= Call Back BabyWare Enabled When the event buffer reaches 90% capacity, the control panel will make two attempts to establish communication with a PC using the BabyWare software by calling the PC Telephone Number programmed in section [915]. The BabyWare software must be in Wait to Dial mode. When the system establishes communication, it will upload the contents of the event buffer to the BabyWare software. If communication is interrupted before completing transmission or if after two attempts communication is not established, the system will wait until the Event Buffer attains another 90% capacity before attempting to re-communicate with the monitoring station. When the Event Buffer is full, each subsequent new event will erase the oldest event in the buffer. For additional security, when a PC using the BabyWare software attempts to communicate with the control panel, the control panel can hang up and call the PC back in order to re-verify identification codes and re-establish communication. When the control panel hangs up, the BabyWare software automatically goes into Wait for Call mode, ready to answer when the control panel calls back. Please note that the PC Telephone Number must be programmed in section [915] in order to use the Call Back feature. Connecting to BabyWare Computer containing BabyWare software Standard DB-
9 cable (9-pin serial cable) 307USB Adapter/CV4USB Converter 4-pin connector cable Serial Connector 50 MG5000+ / MG5050+ Installation Guide User Operation Main Menu Trouble
[1] Wireless zone low battery
[2] Power trouble
[3] Bell trouble
[4] Communication trouble
[5] Tamper and zone wiring failure
[6] Module tamper trouble
[7] Fire loop trouble
[8] Timer loss
[9] Wireless zone supervision loss
[0 (10)] or [10] Module supervision loss
[16] Keypad fault (K32+)
[SLEEP] Keypad fault (K10V/H only) Alarm Display If an alarm has occurred on a zone, the respective zone LED will flash, the [MEM] key will light up, and the zones will be stored in memory. These respective LEDs will continue to flash until disarming even if the zones are restored. To exit this mode and switch to live display mode before disarming, press the [CLEAR] key. Once the system is disarmed, the zones LEDs will turn off, while the [MEM] key remains lit. Press the [MEM] key to illuminate the LEDs corresponding to the zones that were in alarm. The alarm memory will be erased when the next alarm occurs and after a valid code is entered or upon full-arming the system. Trouble Display Press the [TBL] key to view the Trouble Display. Please note that the keypad can be programmed to emit a beep every 5 seconds whenever a new trouble condition has occurred. Press the [TBL] key to stop the beeping. To view the sub-menu, press the corresponding key in the main menu. Sub-Menu Trouble Menu
[1] to [32] Zones in low battery
[1] Low/No battery on the control panel
[2] AC failure on control panel
[3] Auxiliary overload on control panel
[4] Wireless keypad AC failure
[5] Wireless keypad battery failure
[6] Wireless repeater AC failure
[7] Wireless repeater battery failure
[1] Bell disconnect on control panel
[2] Bell overload on control panel
[1] Telephone Line Monitoring on control panel
[2] Fail to communicate on Monitoring Telephone 1 on control panel
[3] Fail to communicate on Monitoring Telephone 2 on control panel
[4] Fail to communicate on pager telephone on control panel
[5] Fail to communicate on voice telephone on control panel
[6] Fail to communicate with PC on control panel
[1] to [32] Zones in tamper and zone wiring failure
[STAY] Panel tamper
[1] 2WPGM
[2] Keypad bus
[3] ZX8/ZX82 Bus Module
[4] RTX3 Bus Module
[5] Wireless keypad
[1] to [32] Zones in fire loop trouble
[1] to [32] Zones in supervision lost6
[STAY] RF interference trouble
[1] 2WPGM
[2] Keypad bus (Panel reset will not clear this trouble, clear it in section [955])
[3] ZX8/ZX82 Bus Module
[4] RTX3 Bus Module
[5] Wireless keypad supervision failure
[6] Wireless repeater supervision failure 51 MG5000+ / MG5050+ Installation Guide INDEX Numerics 101 ................................................................................................................................................ 39 24 Hr. Burglary Zones ............................................................................................................ 24 24 Hr. Buzzer ............................................................................................................................. 24 24 Hr. Freeze Zones ................................................................................................................ 25 24 Hr. Gas Zones ..................................................................................................................... 24 24 Hr. Heat Zones ................................................................................................................... 24 24 Hr. Hold-up Zones ............................................................................................................ 24 24 Hr. Water Zones ................................................................................................................. 24 A AC Failure Report Code ........................................................................................................ 37 AC Power ......................................................................................................................................7 Access Codes ............................................................................................................................ 19 Length .............................................................................................................................. 19 Account ...................................................................................................................................... 40 Ademco Contact ID ................................................................................................................ 39 Ademco Express ...................................................................................................................... 39 Advanced Settings ................................................................................................................. 21 Advanced Technology Zone (ATZ) Connections ........................................................ 12 Alarm ........................................................................................................................................... 35 Alarm Display ........................................................................................................................... 50 Alarm Options .......................................................................................................................... 34 Alarm Report Code Transmission, Delay ........................................................................ 26 Alarm Types .............................................................................................................................. 26 Alternate Dial Option ............................................................................................................ 40 Answering Machine Override ............................................................................................ 48 Armed Report Delay .............................................................................................................. 41 Arming and Disarming Options ........................................................................................ 31 ATZ Wiring Options ............................................................................................................... 27 ATZ Zone Doubling ................................................................................................................ 27 Audible ....................................................................................................................................... 35 Audible Trouble Warning Except AC Failure ................................................................ 46 Audible Trouble Warning on AC Failure ......................................................................... 46 Auto Event Buffer Transmission ........................................................................................ 49 Auto Force Arming ................................................................................................................. 31 Auto Test Report ..................................................................................................................... 41 Auto Zone Shutdown ............................................................................................................ 26 Counter ............................................................................................................................ 26 Report Code ................................................................................................................... 36 Auto-Arming Options ............................................................................................................................ 32 Timer ................................................................................................................................. 32 Timing .............................................................................................................................. 32 Auxiliary Panic Report Code ............................................................................................... 36 Auxiliary Power ...........................................................................................................................9 Auxiliary Supply Report Code ............................................................................................ 37 B Backup Battery ............................................................................................................................7 Battery specifications ....................................................................................................................6 Battery Charge Current ......................................................................................................... 45 Battery Failure Report Code ................................................................................................ 37 Battery, Backup ...........................................................................................................................7 Beep On Exit Delay ................................................................................................................. 33 Bell Cut-Off Timer ................................................................................................................... 34 Bell Output Connection ........................................................................................................................9 Disconnected Report Code ...................................................................................... 37 Overload Report Code ............................................................................................... 37 Bell Squawk On Arm/Disarm With Keypad .................................................................................................................. 33 52 With Remote Control ................................................................................................. 33 Bypassable Zones ................................................................................................................... 26 C Call Back Feature .................................................................................................................... 49 Cancel Auto-Arm Report Code .......................................................................................... 36 Charge Current ........................................................................................................................ 45 Closing Delinquency ............................................................................................................. 41 Cold Start Report Code ........................................................................................................ 37 Configuring The LED Keypads ........................................................................................... 15 Connecting Bells or Sirens ...................................................................................................................9 Fire Zones ....................................................................................................................... 13 PGMs ................................................................................................................................ 10 Single Zone Inputs ...................................................................................................... 11 Telephone Lines ..............................................................................................................9 Counter, Auto Zone Shutdown ......................................................................................... 26 D Data Display Mode ................................................................................................................. 14 Daylight Savings Time .......................................................................................................... 46 Delay ...................................................................................................................................33, 42 Before Alarm Report Code Transmission ............................................................ 26 Between Dialing Attempts ....................................................................................... 40 Power Failure Report .................................................................................................. 41 Delay Zone Bypassed ............................................................................................................ 31 Delayed Fire Silent Zones .................................................................................................... 24 Delayed Fire Zones ................................................................................................................ 24 Dial ............................................................................................................................................... 40 Dialer settings .......................................................................................................................... 36 Dialing Attempts .................................................................................................................... 40 Dialing Method ....................................................................................................................... 40 Disable Test Reporting ......................................................................................................... 42 Disarmed Report Delay ........................................................................................................ 41 Display ........................................................................................................................................ 47 Display Entry Delay ................................................................................................................ 47 Display Exit Delay ................................................................................................................... 47 Duress ......................................................................................................................................... 20 Duress Report Code ............................................................................................................... 36 E Emergency Panic Report Code .......................................................................................... 36 Entry Delay 2 / Stay / Sleep Zones .................................................................................... 23 Entry Delay on LCD keypad ................................................................................................ 47 Entry/Exit ................................................................................................................................... 21 Entry/Exit with a Keypad ...................................................................................................... 21 Entry/Exit with a Remote Control ..................................................................................... 21 EOL Zones ................................................................................................................................. 27 Event Buffer Transmission ................................................................................................... 49 Exit Delay ................................................................................................................................... 33 Exit Delay on LCD keypad ................................................................................................... 47 F Fail ................................................................................................................................................ 42 Fail to Communicate Report Code ................................................................................... 37 Feature Select Programming Method ............................................................................ 14 Features, Wireless ................................................................................................................... 29 Fire Circuits ............................................................................................................................... 13 Fire Loop Trouble Report Code ......................................................................................... 37 Fire Panic Report Code ......................................................................................................... 36 Flex .............................................................................................................................................. 35 Follow / Stay / Sleep Zones ................................................................................................. 23 MG5000+ / MG5050+ Installation Guide Follow / Stay Zones ................................................................................................................ 23 Follow No Pre-Alarm ............................................................................................................. 25 Follow Zones ............................................................................................................................ 23 Force ............................................................................................................................................ 40 Force Arming ............................................................................................................................ 20 Force Zones .............................................................................................................................. 27 G Ground ...........................................................................................................................................7 H Hardware Reset ....................................................................................................................... 45 Options I Input Numbers Keyswitch Numbering ................................................................................................ 28 Installation ....................................................................................................................................7 Installer Code ................................................................................................................................. 19 Lock ................................................................................................................................... 45 Quick Functions Keys ................................................................................................. 46 Installer In Report Code ........................................................................................................ 37 Installer Out Report Code .................................................................................................... 37 Instant / Stay / Sleep Zones ................................................................................................. 23 Instant / Stay Zones ............................................................................................................... 23 Instant Fire Silent Zones ....................................................................................................... 24 Instant Fire Zones ................................................................................................................... 23 Instant No Pre-Alarm ............................................................................................................. 25 Instant Zones ............................................................................................................................ 23 Intellizone .................................................................................................................................. 26 K Keypad Keyswitch Lockout Report Code .................................................................................................. 36 Panic Options ................................................................................................................ 35 Arm Only ......................................................................................................................... 28 Definitions ...................................................................................................................... 28 Keyswitch Numbering ................................................................................................ 28 Maintained ..................................................................................................................... 28 Momentary ..................................................................................................................... 28 Options ............................................................................................................................ 28 Stay/Instant Disarm ..................................................................................................... 28 L Late to Close Report Code ................................................................................................... 36 Length of Access Codes ....................................................................................................... 19 Location and Mounting ...........................................................................................................7 Lock Master Code ................................................................................................................... 20 Lock-out ..................................................................................................................................... 45 Lockout ....................................................................................................................................... 35 M Maintenance Code ................................................................................................................. 19 Maximum Dialing Attempts ............................................................................................... 40 Message ..................................................................................................................................... 42 Mode ........................................................................................................................................... 21 Module Fault Report Code .................................................................................................. 37 Mounting ......................................................................................................................................7 Multiple Feature Select Programming Method ........................................................... 14 N No Arming On Battery Fail .............................................................................................................. 31 On Tamper Trouble ............................................................................................. 31, 32 No Audible Feedback Upon Stay Arming ...................................................................... 33 No Exit Delay When Arming with Remote Control .................................................... 33 No Movement Auto-Arming .............................................................................................. 32 No Movement Report Code ............................................................................................... 36 Number of Rings ..................................................................................................................... 48 Numbers .................................................................................................................................... 40 O One-Touch Arming ................................................................................................................ 33 Report Code .................................................................................................................. 36 Alarm ................................................................................................................................ 34 Arming and Disarming .............................................................................................. 31 Auto-Arming ................................................................................................................. 32 User code ........................................................................................................................ 19 Zone ................................................................................................................................. 25 Override Answering Machine ............................................................................................ 48 P Pager ........................................................................................................................................... 42 Panel Answer Options .......................................................................................................... 48 Panel Identifier ........................................................................................................................ 48 Panic ............................................................................................................................................ 35 Panic Options ...................................................................................................................35, 43 Partial Arming Report Code ................................................................................................ 36 Partition Account Numbers ................................................................................................ 38 Partition Assignment, Zone ................................................................................................ 25 Partitioning ............................................................................................................................... 45 Paths ........................................................................................................................................... 21 PC Password ............................................................................................................................. 48 PC Telephone Number ......................................................................................................... 48 Personal ..................................................................................................................................... 42 Personal Dialing Numbers .................................................................................................. 38 PGM ............................................................................................................................................. 43 PGM (Control Panel) Activation Event ........................................................................................................... 43 Deactivation Event ...................................................................................................... 43 PGM Delay ...................................................................................................................... 43 PGM Activation, User Code Option .................................................................................. 20 Power .............................................................................................................................................7 Power Failure Report Delay ................................................................................................ 41 Programmable Output Connections .............................................................................. 10 Programmable Outputs ....................................................................................................... 43 Programming Methods .......................................................................................................................... 14 Using a Keypad ............................................................................................................. 14 Wireless Features ......................................................................................................... 29 Pulse ............................................................................................................................................ 40 Pulse Ratio ................................................................................................................................. 40 Q Quick Arming ........................................................................................................................... 33 R Re-arm ........................................................................................................................................ 21 Recent Close Delay ................................................................................................................ 41 Recent Closing Report Code .............................................................................................. 36 Recycle Alarm .......................................................................................................................... 34 Regular Arming Switches to Force Arming ................................................................... 31 Remote Arming Report Code ............................................................................................ 36 Remote Controls Deleting .......................................................................................................................... 29 Programming ................................................................................................................ 29 53 MG5000+ / MG5050+ Installation Guide Trouble Restore Codes ....................................................................................... 36, 37 T Tamper Bypass Options ....................................................................................................... 34 Tamper Recognition .............................................................................................................. 34 Telephone Line Connection ..................................................................................................9 Telephone Line Monitoring (TLM) ................................................................................... 42 Telephone Number, PC ........................................................................................................ 48 Telephone Numbers ............................................................................................................. 38 Termination .............................................................................................................................. 33 Test Report Automatic ....................................................................................................................... 41 Report Code .................................................................................................................. 37 Timed Auto-Arming .............................................................................................................. 32 Report Code .................................................................................................................. 36 Timer .......................................................................................................................... 35, 41, 42 Timer Loss Report Code ....................................................................................................... 37 TLM .............................................................................................................................................. 42 Transmission Options ........................................................................................................... 41 Trouble Display ....................................................................................................................... 50 U Upload/Download Software .............................................................................................. 14 User Code Options Arm Only ......................................................................................................................... 20 Bypass Programming ................................................................................................. 20 Partition 1 Assignment .............................................................................................. 19 Partition 2 Assignment .............................................................................................. 20 PGM Activation ............................................................................................................. 20 Stay Arming ................................................................................................................... 20 User Operation ........................................................................................................................ 50 W Window ...................................................................................................................................... 21 Winload Software ................................................................................................................... 14 Wireless Features .................................................................................................................... 29 Wireless Low Battery Report Code ................................................................................... 37 Wireless Transmitters Check-in Supervision Timer Settings ................................................................... 29 Programming ................................................................................................................ 44 Viewing Signal Strength ........................................................................................... 44 Z Zone Definition Status .......................................................................................................... 25 Zone Definitions ..................................................................................................................... 22 Zone Input 1 Becomes a 2-wire Smoke Input .............................................................. 27 Zone Options Delay Before Alarm Report Code Transmission ............................................... 26 Force Zones ................................................................................................................... 26 Zone Programming ............................................................................................................... 22 Zone Restore Report Options ............................................................................................ 42 Zone Shutdown, Auto .......................................................................................................... 26 Zone Timers .............................................................................................................................. 27 Programming Remote Control Buttons .............................................................. 30 Remote Disarm Report Code .............................................................................................. 36 Repetition .................................................................................................................................. 42 Report ......................................................................................................................................... 41 Report Code, Special Cold Start ........................................................................................................................ 37 Installer In ....................................................................................................................... 37 Installer Out ................................................................................................................... 37 Test Report ..................................................................................................................... 37 Report Code, Special Alarm Auto Zone Shutdown ................................................................................................. 36 Auxiliary Panic ............................................................................................................... 36 Duress .............................................................................................................................. 36 Emergency Panic .......................................................................................................... 36 Fire Panic ......................................................................................................................... 36 Keypad Lockout ............................................................................................................ 36 Recent Closing .............................................................................................................. 36 Report Code, Special Arming Late to Close .................................................................................................................. 36 No Movement ............................................................................................................... 36 One-Touch Arming ..................................................................................................... 36 Partial Arming ............................................................................................................... 36 Remote Arming ............................................................................................................ 36 Timed Auto-Arming .................................................................................................... 36 Report Code, Special Disarming Cancel Auto-Arm .......................................................................................................... 36 Remote Disarm ............................................................................................................. 36 Report Code, System Trouble AC Failure ........................................................................................................................ 37 Auxiliary Supply ............................................................................................................ 37 Battery Failure ............................................................................................................... 37 Bell Output Disconnected ........................................................................................ 37 Bell Output Overload .................................................................................................. 37 Fail to Communicate .................................................................................................. 37 Fire Loop Trouble ......................................................................................................... 37 Module Fault ................................................................................................................. 37 Timer Loss ....................................................................................................................... 37 Wireless Low Battery ................................................................................................... 37 Reporting ................................................................................................................................... 42 Reporting and Dialer settings ............................................................................................ 36 Reporting Formats ................................................................................................................. 39 Reset, Hardware ...................................................................................................................... 45 Restrict Arming On Battery Fail ............................................................................................................... 31 On Tamper Trouble ..............................................................................................31, 32 RF Jamming Supervision ...................................................................................................... 29 RF Supervision ......................................................................................................................... 26 Rings ............................................................................................................................................ 48 S Silent ............................................................................................................................................ 35 Single Digit Data Entry Method (Decimal and Hexadecimal) ................................. 14 Single Zone Inputs ................................................................................................................. 11 Software, Upload/Download .............................................................................................. 14 Special Alarm Report Codes ............................................................................................... 36 Special Arming Report Codes ............................................................................................ 36 Special Disarming Report Codes ....................................................................................... 36 Special Reporting Codes ...................................................................................................... 37 Specifications ..............................................................................................................................6 Standard Pulse Formats ....................................................................................................... 39 StayD ........................................................................................................................................... 21 Switch ......................................................................................................................................... 40 Switch to Stay Arming .......................................................................................................... 31 System ........................................................................................................................................ 41 Master Code ................................................................................................................... 19 Settings ............................................................................................................................ 45 Trouble Report Codes ................................................................................................ 37 54 The whole Paradox team wishes you a successful and easy installation. We hope this product performs to your complete satisfaction. Should you have any questions or comments, please contact us at support@paradox.com. Additional information can be found on our website www.paradox.com/support Printed in Canada - 12/2021 PARADOX.COM MG5000+/MG5050+-EI00 DRAFT
| 1 | Internal Photos | Internal Photos | 345.12 KiB | December 21 2021 / June 20 2022 | delayed release |
| 1 | ID Label/Location Info | ID Label/Location Info | 106.59 KiB | December 21 2021 |
Paradox Security Systems Ltd. FCC ID: KDYMG5050PLUS IC:2438A-MG5050PLUS The label shown below is affixed on the rear side of the detector. The label material is PVC with a permanent adhesive. Label Page 1 of 2 Paradox Security Systems Ltd. FCC ID: KDYMG5050PLUS IC:2438A-MG5050PLUS Label location Label with FCC ID:KDYMG5050PLUS and IC:2438A-MG5050PLUS will be located here. The statement according to FCC part 15 15.19(a)(3) is placed in User Manual, page 2 (Application exhibit User_manual_44733_Rev1). Page 2 of 2
| 1 | Confidentiality | Cover Letter(s) | 111.54 KiB | December 21 2021 |
FCC, Request for non-disclosure RF_501, Issue 7 Date: 19-Oct-10 Page 1 of 1 Company Name: Paradox Security Systems Address:
City:
Country:
780 Industriel Blvd Saint-Eustache, QC, J7R 5V3 Canada To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: KDYMG5050PLUS Reference number: ######
Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:
Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1):
Internal Photos Users Manual Test Set-up Photos External Photos Justification: Patent pending, Competative advantage Planned Release Date STC: 180 days from the grant date (notes 2, 3, 4, 5). If no date is given, 45 days from grant date will be used. Date: December 20, 2021 Name and signature of applicant: Alex Chaplik Notes:
1) A document or type of document can only have ONE type of confidentiality!
2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!
3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!
5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period
| 1 | Declaration of authorization | Cover Letter(s) | 105.10 KiB | December 21 2021 |
RF_160, Issue 04 Paradox Security Systems Ltd. 780 Industriel Blvd . Saint-Eustache, Quebec J7R 5V3. Canada . Hermon Laboratories Ltd.. Harakevet Industrial Zone .. Binyamina 30500.. Israel . Declaration of Authorization We Name:
Address:
City:
Country:
Declare that:
Name Representative of agent: . (1) Agent Company name:
Address:
City:
Country is authorized to apply for Certification of the following product(s):
Product description: Wireless Control Panel Type designation:
Trademark:
Validity/ expiry date: December 09, 2022 on our behalf. Date:
City:
Name:
Function:
Alex Chaplik .. (2) December 09, 2021 Saint-Eustache .. Certification manager . MG5050+, MG5000+ . Paradox. Signature:
Notes:
(1): Required for FCC application
(2): For FCC it must be the Grantee Code owner or the authorized agent.
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2021-12-21 | 433.92 ~ 433.92 | DSR - Part 15 Remote Control/Security Device Transceiver | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2021-12-21
|
||||
| 1 | Applicant's complete, legal business name |
Paradox Security Systems
|
||||
| 1 | FCC Registration Number (FRN) |
0007597024
|
||||
| 1 | Physical Address |
780 Industriel Blvd
|
||||
| 1 |
Quebec, N/A J7R 5V3
|
|||||
| 1 |
Canada
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
c******@telefication.com
|
||||
| 1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
KDY
|
||||
| 1 | Equipment Product Code |
MG5050PLUS
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
A****** C****
|
||||
| 1 | Title |
Certification Manager
|
||||
| 1 | Telephone Number |
450-4********
|
||||
| 1 | Fax Number |
450-4********
|
||||
| 1 |
a******@paradox.com
|
|||||
| app s | Technical Contact | |||||
| 1 | Firm Name |
Hermon Laboratories Ltd.
|
||||
| 1 | Name |
M**** N******
|
||||
| 1 | Physical Address |
Harakevet Industrial zone, P.O.Box 23
|
||||
| 1 |
Binyamina
|
|||||
| 1 |
Israel
|
|||||
| 1 | Telephone Number |
+9724********
|
||||
| 1 | Fax Number |
97246********
|
||||
| 1 |
n******@hermonlabs.com
|
|||||
| app s | Non Technical Contact | |||||
| 1 | Firm Name |
Paradox Security Systems Ltd.
|
||||
| 1 | Name |
A******** C****
|
||||
| 1 | Physical Address |
780 Industrial Blvd
|
||||
| 1 |
Quebec, J7R 5V3
|
|||||
| 1 |
Canada
|
|||||
| 1 | Telephone Number |
97248********
|
||||
| 1 | Fax Number |
97248********
|
||||
| 1 |
a******@paradox.com
|
|||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 06/20/2022 | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | DSR - Part 15 Remote Control/Security Device Transceiver | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless Control Panel | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Hermon Laboratories Ltd.
|
||||
| 1 | Name |
G**** S******
|
||||
| 1 | Telephone Number |
97246********
|
||||
| 1 | Fax Number |
+972 ********
|
||||
| 1 |
G******@HERMONLABS.com
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 15.231 | 433.92000000 | 433.92000000 | |||||||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC