EM-200 User Manual Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Disclaimer The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes. Trademark recognition All product names used in this manual are the properties of their respective owners and are acknowledged. Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the systems manufacturer could void the users authority to operate the equipment. Declaration of conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:
This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Your E-Menu is a data transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on the safety standards previously set by both U.S. and international standards bodies:
American National Standards Institute (ANSI) IEEE. C95.1-1992National Council on Radiation Protection and Measurement (NCRP). Report 86. 1986International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1996Ministry of Health (Canada), Safety Code 6. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.The highest SAR value for this E-Menu tested by DASY5 for use at the body is 0.097 W/kg FCC RF Exposure requirements:
SAR compliance for body-worn operations is restricted which provide at least 2 cm separation between the device and the users body. i About this manual This manual is intended for system administrators who are familiar with setting up a new system and installing an operating system. The manual consists of the following sections:
Chapter 1 Getting Started:
Chapter 2 BIOS Setup Utility:
Chapter 3 Upgrading Components:
Appendix:
This section covers unpacking and checking the package contents, identifying components, installing the battery pack, charging the battery and powering on. The BIOS chapter provides information on navigating and changing settings in the BIOS Setup Utility. This section provides information on upgrading components. The appendix covers troubleshooting, information on having the EM-200 serviced, and technical specications. Safety information Before installing and using the EM-200, take note of the following precautions:
Read all instructions carefully. Do not place the unit on an unstable surface, cart, or stand. Do not block the slots and opening on the unit, which are provided for ventilation. Do not push objects in the ventilation slots as they may touch high voltage components and result in shock and damage to the components. Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. Follow all warnings and cautions in this manual and on the unit case. When replacing parts, ensure that your service technician uses parts specified by the manufacturer. Avoid using the system near water, in direct sunlight, or near a heating device. Never throw the battery into a fire or put it near a fire. Warning! Batteries may explode if not handled properly. Do not disas-
semble or dispose of them in re. Keep them away from children. Follow local regulations when disposing of used batteries.
WARNING
Revision history Version 1.0, August 2009 ii TABLE OF CONTENTS CHAPTER 1 GETTING STARTED ................................................ 1 Unpacking the machine..................................................................................1 Checking the package contents ....................................................................2 Identifying components .................................................................................3 Installing the battery pack ..............................................................................8 Charging the battery pack ..............................................................................9 Powering on .................................................................................................10 CHAPTER 2 BIOS SETUP ...........................................................11 About the Setup Utility .................................................................................11 Using the USB keyboard ..............................................................................11 Entering the Setup Utility ........................................................................12 BIOS Navigation Keys .............................................................................12 Using BIOS .............................................................................................13 Main Menu ...................................................................................................14 Advanced Menu ...........................................................................................15 Boot Conguration ..............................................................................16 IDE Conguration ................................................................................17 Channel 1 Master ................................................................................18 Security Menu ..............................................................................................19 Boot Menu ....................................................................................................20 Boot Device Priority ..............................................................................21 Boot Type Order ...................................................................................21 Exit Menu .....................................................................................................22 CHAPTER 3 UPGRADING COMPONENTS ............................... 23 Safety and precautions ...............................................................................23 Before you begin ..........................................................................................24 Upgrading the hard drive..............................................................................25 Upgrading the memory module ....................................................................27 Upgrading the Mini-PCIE card .....................................................................28 APPENDIX .................................................................................. 31 Troubleshooting ...........................................................................................31 Tips for Troubleshooting ...............................................................................31 General Problems .......................................................................................32 Having the EM-200 Serviced ......................................................................33 Specication .................................................................................................34 iii iv CHAPTER 1 GETTING STARTED Checking the package contents After you unpack the device, check that the following items are included. This chapter describes the procedures from unpacking the EM-200, to powering it on. The following topics are described. Powering on on page 10 Unpacking the machine on page 1 Checking the package contents on page 2 Identifying components on page 3 Installing the battery pack on page 8 Charging the battery pack on page 9 Unpacking the machine The machine and cable accessories are packed in a cardboard carton with foam padding for protection during shipping. EM-200 Battery Driver CD with drivers and the user manual PDF le. Protection pack Figure 1.1 Unpacking the machine AC adapter Power cord Carefully unpack the machine and keep the packing materials. If you need to ship it in the future, repack it as shown in Figure 1.1. If any item is missing or appears damaged, contact your dealer immediately. 1 2 C H A P T E R 1 G E T T I N G S TA R T E D Identifying components This section describes the parts and connectors on the machine. Front view 1 2 3 4 5 6 7 Left view 1 2 3 4 5 6 Figure 1.3 Left view Component Description 1 2 3 4 5 6 5-in-1 media card slot Express card 34 slot USB port Power button RJ45 LAN jack DC IN 3 4 C H A P T E R 1 G E T T I N G S TA R T E D Figure 1.2 Front view Component 8 9 Description 1 2 3 4 5 6 7 8 Power indicator Battery charging indicator HDD status indicator WiFi On/ Off indicator Bluetooth On/ Off indicator Built-in Microphone Camera (optional) 10.1-inch touch panel Right view Rear view 1 2 3 4 5 1 2 1 Figure 1.4 Right view Figure 1.5 Rear view Component Description 1 2 3 4 5 VGA port USB port Ventilation hole Headphone jack Microphone jack Component Description 1 2 Speaker Battery pack 5 6 C H A P T E R 1 G E T T I N G S TA R T E D Bottom view 1 2 1 Installing the battery pack 1. Overturn the EM200 so that the bottom is facing up toward you, as shown in the right. Slide the battery release latch to the unlock position. 3 4 5 6 7 Figure 1.6 Bottom view Component Description 1 2 3 4 5 6 7 Mounting hole Camera (optional) Battery lock switch Memory, WiFi module, Bluetooth module slots Battery pack HDD compartment Battery release latch 2. Align EM200 battery compartment pins to the battery connector. Slightly slide and press the battery pack into the compartment until the battery lock switch is bounced back. 3. As shown in the right, slide the battery release latch to the lock posi-
tion. 7 8 C H A P T E R 1 G E T T I N G S TA R T E D Charging the battery pack Plug the AC adapter power cord into an electrical outlet, then connect the DC plug of the adapter cable to the EM-200. It takes approximately 24 hours to fully charge the battery for the rst time. Subsequent charges might take longer. Powering on The power button located on the left side of the EM200, press the power button the turn it on. NOTE IMPORTANT IMPORTANT Charge the battery within a temperature range 0C to 45C. To protect and prolong the life of the battery, do not charge it for 24 hours or longer at a time. Please make sure to perform 3 complete full charge and discharge cycles to get optimal battery capacity. Failure to comply will result in shorter battery lifespan. NOTE To force power off , long press the power button for 4~5 seconds. 9 10 C H A P T E R 1 G E T T I N G S TA R T E D CHAPTER 2 BIOS SETUP The primary function of the BIOS (Basic Input and Output System) is to identify and initiate component hardware. The BIOS parameters are stored in non-volatile BIOS memory (CMOS). CMOS contents dont get erased when the computer is turned off. The following topics are described in this chapter. 1 About the Setup Utility on page 1 Using the USB keyboard on page 1 1 Main Menu on page 1 4 Advanced Menu on page 1 5 Security Menu on page 1 9 Boot Menu on page 2 0 2 Exit Menu on page 2 About the Setup Utility The BIOS Setup Utility enables you to congure the following items:
Hard drives, diskette drives, and peripherals Password protection from unauthorized use Power management features Boot device priority This Setup Utility should be used for the following:
When changing the system conguration When a conguration error is detected and you are prompted to make changes to the Setup Utility When making changes to the Power Management conguration When changing the User or Supervisor password When changing the boot priority Using the USB keyboard To enter the BIOS setup must use the external keyboard. Please connect USB keyboard and restart, then refer to the section entering the Setup Utility. Entering the Setup Utility Press the F2 key during booting to access the BIOS Setup Utility:
Item Specific Help Main Advanced Security Boot Exit InsydelH2O Setup Utility System BIOS Version GA-D1USB28 F04 Processor Type System Bus Speed System Memory Speed Intel(R) Atom(TM) CPU N270
@ 1.66GHz 533 MHz 533 MHz Cache RAM Total Memory 0512 KB 1024 MB System Time System Date
[18:47:25]
[06/21/2009]
F1 Help Select Item F7/F8 Change Values F9 Setup Default ESC Exit Select Menu Enter SelectSub-Menu F10 Save and Exit Figure 2.1 Main BIOS menu BIOS Navigation Keys The BIOS navigation keys are listed below. Key Function Esc F1 F7/F8 F9 F10 Enter Select the menu titles Select the items Exits the current menu Displays a screen that describes all key functions Changes the selected elds values Loads the setup default values Saves the current conguration and exits Setup Selects or enters submenu 11 12 C H A P T E R 2 B I O S S E T U P Using BIOS When you start the Setup Utility, the main menu appears. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>. Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information. Some options (marked with a triangle ) lead to submenus that enable you to change the values for the option. Use the cursor arrow keys to scroll through the items in the submenu. Main Menu Press right/left arrow key to select the Main menu, which displays the following screen:
Main Advanced Security Boot Exit InsydelH2O Setup Utility System BIOS Version GA-D1USB28 F04 Processor Type System Bus Speed System Memory Speed Intel(R) Atom(TM) CPU N270
@ 1.66GHz 533 MHz 533 MHz Cache RAM Total Memory 0512 KB 1024 MB System Time System Date
[18:47:25]
[06/21/2009]
Item Specific Help Figure 2.2 Main menu F1 Help Select Item F7/F8 Change Values F9 Setup Default ESC Exit Select Menu Enter SelectSub-Menu F10 Save and Exit System BIOS Version This item shows the information about BIOS version. Processor Type This item shows the CPU type. System Bus Speed This item shows the FSB speed. System Memory Speed This item shows the memory clock speed. Cache RAM This item shows the size of the cache RAM. Total Memory This eld displays the amount of memory detected by the system during boot. System Time / Date The Time and Date items show the current date and time held by the machine. These will be automatically updated whenever you make changes to the Windows Date and Time Properties utility. 13 14 C H A P T E R 2 B I O S S E T U P Advanced Menu Press right/left arrow key to select the Advanced menu, which displays the following screen:
Boot Conguration Use this submenu to set the boot conguration. Select the item and press <Enter> to open the following menu:
Main Advanced Security Boot Exit InsydelH2O Setup Utility Boot Configuration IDE Configuration Advanced S3 Keyboard Language
[Enabled]
[US, Chinese]
Item Specific Help Main Advanced Security Boot Exit InsydelH2O Setup Utility Boot Configuration Numlock
[Off]
Item Specific Help Figure 2.3 Advanced menu Figure 2.4 Conguration submenu Boot F1 Help Select Item F7/F8 Change Values F9 Setup Default ESC Exit Select Menu Enter SelectSub-Menu F10 Save and Exit F1 Help Select Item F7/F8 Change Values F9 Setup Default ESC Exit Select Menu Enter SelectSub-Menu F10 Save and Exit Advanced S3 This item is used to enable/ disable the ACPI S3 mode, it can turn on and off the PC within seconds. Keyboard Language This item is used to select the keyboard language of external USB keyboard. Numlock This item is used to turn on/off the numlock of the external keyboard at boot. 15 16 C H A P T E R 2 B I O S S E T U P IDE Conguration Use this submenu to set the IDE conguration. Select the item and press <Enter> to open the following menu:
Channel 1 Master Use this submenu to set the hard disk drive, Select the item and press <Enter> to open the following menu:
Main Advanced Security Boot Exit InsydelH2O Setup Utility IDE Configuration Item Specific Help HDC Configure as ATA/IDE Mode
[SATA Only]
[Native]
Channel 1 Master
[WDC WD1600BEV1-222CT]
Figure 2.5 Conguration submenu IDE Advanced InsydelH2O Setup Utility Channel 1 Master [WDC WD1600BEVT-22ZCT]
Item Specific Help Type : [Auto]
Transfer Mode: [Auto]
32Bit I/O: <Enabled>
Block Mode: <Enabled>
Transfer Mode: <Ultra DMA ATA-100>
S.M.A.R.T <Enabled>
Security Mode:
Uninstall Figure 2.6 Master submenu Channel 1 F1 Help Select Item F7/F8 Change Values F9 Setup Default ESC Exit Select Menu Enter SelectSub-Menu F10 Save and Exit F1 Help Select Item F7/F8 Change Values F9 Setup Default ESC Exit Select Menu Enter SelectSub-Menu F10 Save and Exit HDC Congure as This item is used to select the hard disk interface type. ATA/IDE Mode This item is used to select the ATA/IDE mode. Channel 1 Master Displays the name of the current hard disk device in channel 1 master. Type:
If you leave this item at Auto, the system will automatically detect and congure the device it channel 1 master. If you change the value to User Dened and then manually congure the drive by entering the characteristics of the drive in the elds described below:
32Bit I/O when enabled, allows the system to improve the hard drive performance for 32Bit OS. Block Mode when enabled, allows the system to perform accesses to the hard disk in block mode. Transfer Mode displays the data transfer mode. S.M.A.R.T when enabled, allows the system to support S.M.A.R.T (Self-Monitoring, Analysis, and Reporting Technology) for hard disk device. Security Mode displays the security mode status. 17 18 C H A P T E R 2 B I O S S E T U P Security Menu The security system allows you to set a password to prevent unauthorized access to BIOS. Press right/left arrow key to select the Security menu, which displays the following screen:
Boot Menu This menu allows the user to set the boot-related options. Press right/left arrow key to select the Boot menu, which displays the following screen:
Main Advanced Security Boot Exit InsydelH2O Setup Utility Supervisor Password :
User Password :
Not Installed Not Installed Set Supervisor Password Set User Password Item Specific Help Main Advanced Security Boot Exit InsydelH2O Setup Utility Quiet Boot Boot Type
[Enabled]
Item Specific Help Figure 2.7 Security menu Figure 2.8 Boot Menu F1 Help Select Item F7/F8 Change Values F9 Setup Default ESC Exit Select Menu Enter SelectSub-Menu F10 Save and Exit Quiet Boot When enabled, system will boot without message. In contrast, when disabled, system will boot in text mode. F1 Help Select Item F7/F8 Change Values F9 Setup Default ESC Exit Select Menu Enter SelectSub-Menu F10 Save and Exit Supervisor/ User Password These two elds indicate if the Supervisor/ User Passwords are set or not. Installed: System Password is set. Not Installed: System Password is not set. Set Supervisor and User Passwords These items can be used to install a password. A Supervisor password takes precedence over a User password, and the Supervisor can limit the activities of a User. To install a password, follow these steps:
1. Highlight the item Set Supervisor/User Password on the Security menu and press <Enter>. 2. The password dialog box appears. Please type in your new password 3. If you are installing a new password, type in the password. You can type up to eight alphanumeric characters. Symbols are ignored. The Set Supervisor/User Password item differentiates between upper and lower case characters. Press <Enter> after you have typed in the password. To conrm the password, type the password again and press <Enter>. To clear the password, leave the dialog box blank, press <Enter>, when the conrm box appears, press <Enter> again. 4. Write the passwords down and keep them in a safe place. Power on password When enabled, system will ask input password on post time. When disabled, system will ask input password when go to Setup Utility. User Access Level This item allows you to congure the user access level. View Only - users can only view the Bios settings and can not change the settings. Limited - allows users to change some settings. Full - users can change all of the BIOS settings. 19 20 C H A P T E R 2 B I O S S E T U P Boot Device Priority Select the Boot Type item and press <Enter> to open the following menu:
Main Advanced Security Boot Exit InsydelH2O Setup Utility Boot Device Priority Boot Type Order Item Specific Help Exit Menu This menu allows the user to save CMOS setting and exit the Setup Utility. Press right/left arrow key to select the Exit menu, which displays the following screen:
Main Advanced Security Boot Exit InsydelH2O Setup Utility Item Specific Help Exit Saving Changes Exit Discarding Changes Load Optimal Defaults Discard Changes Figure 2.9 Priority submenu Boot Device Figure 2.11 Exit Menu F1 Help Select Item F7/F8 Change Values F9 Setup Default ESC Exit Select Menu Enter SelectSub-Menu F10 Save and Exit Boot Type Order This submenu allows the user to decide the order of boot devices to load the operating system. Select the Boot Type item and press <Enter> to open the following menu:
F1 Help Select Item F7/F8 Change Values F9 Setup Default ESC Exit Select Menu Enter SelectSub-Menu F10 Save and Exit Exit Saving Changes Allows the user to save changes to CMOS and reboot the system. The following message is prompted when the user presses <Enter> on the item. Boot InsydelH2O Setup Utility Boot Type Order Hard Disk Drive USB CD/DVD ROM Driver USB Memory Others Item Specific Help Exit Saving Changes
[Yes] [No]
Figure 2.10 Order submenu Boot Type Exit Discarding Changes Allows the user to exit Setup without saving changes to CMOS. The following message is prompted when user presses <Enter> on the item. F1 Help Select Item F7/F8 Change Values F9 Setup Default ESC Exit Select Menu Enter SelectSub-Menu F10 Save and Exit Select a media type, and then use F7 or F8 key to move up or down the item in order to arrange the boot priority. Exit Discarding Changes
[Yes] [No]
Load Optimal Defaults Allows the user to load the default value in CMOS Setup. The following message is prompted when the user presses <Enter> on this item. Load Optimal Defaults
[Yes] [No]
Discard Changes Allows the user to discard the changes. The following message is prompted when the user presses <Enter> on this item. Discard Changes
[Yes] [No]
21 22 C H A P T E R 2 B I O S S E T U P Before you begin Make sure you have a stable, clean working environment. Dust and dirt can get into components and may cause malfunction. Adequate lighting and proper tools can prevent you from accidentally damaging the internal components. Most of the electrical and mechanical connections can be disconnected by using your ngers. It is recommended that you do not use needle-nosed pliers to disconnect connectors as these can damage the soft metal or plastic parts of the connectors. To prevent scratching the case of the machine, make sure the worktop surface is clean and at. CAUTION This chapter describes how to upgrade components for the EM-200. The following topics are described. CHAPTER 3 UPGRADING COMPONENTS Safety and precautions on page 2 3 Before you begin on page 2 4 Upgrading the hard drive on page 2 5 Upgrading the memory module on page 2 7 Upgrading the Mini-PCIE card on page 2 8 Safety and precautions Computer components and electronic circuit boards can be damaged by discharges of static electricity. Working on computers that are still connected to a power supply can be extremely dangerous. Follow these guidelines to avoid damage to the computer or injury to yourself. Always disconnect the unit from the power outlet. Leave all components inside the static-proof packaging that they ship with until they are ready for instal-
lation. After replacing optional devices, make sure all screws, springs, or other small parts are in place and are not left loose inside the case. Metallic parts or metal akes can cause electrical shorts. Only qualied personnel should perform repairs on the machine. Damage due to unauthorized servicing is not covered by the warranty. If you are not condent of installing a hard drive, memory card or LAN card, we recommend that you refer the job to qualied personnel. CAUTION If the LCD breaks and uid gets onto your hands or into your eyes, immediately wash with water and seek medical attention. The inverter card has high voltage. Do not touch the inverter card while power is connected to the machine. Unplug the power cord before attempting to replace any part. To prevent static damage to components, wear a grounded wrist strap. Alternatively, discharge any static electricity by touching the bare metal chassis of the unit case, or the bare metal body of any other grounded appliance. Hold electronic circuit boards by the edges only. Do not touch the components on the board unless it is necessary to do so. Do not ex or stress the circuit board. Do not hold components such as a processor by its pins; hold it by the edges. WARNING WARNING CAUTION CAUTION 23 24 C H A P T E R 3 U P G R A D I N G C O M P O N E N T S Upgrading the hard drive Refer to the following to remove and replace the hard drive. 1. 2. 3. 4. Turn off the EM-200. Disconnect the AC adapter cable. Overturn the EM200. Remove the two screws as shown in the right. 5. Open and remove the hard drive compartment cover. 6. Slide the hard drive to disconnect. 7. Remove the hard drive. 8. Remove the four screws, then remove the hard drive out from the tray. To replace the hard drive, reverse the above procedure. 25 26 C H A P T E R 3 U P G R A D I N G C O M P O N E N T S Upgrading the memory module Refer to the following to remove and replace the memory. 1. 2. 3. 4. Turn off the EM-200. Disconnect the AC adapter cable. Overturn the EM200. Remove the two screws as shown in the right. 5. Open and remove the memory module compartment cover. 6. Locate the memory module, as shown in the right. 7. Pop out the two silver latches holding the memory module into place. The module pops up. Grasp the outer edges of the memory module with thumb and forenger, and then gently remove it. To replace the memory module, reverse the above procedure. Upgrading the Mini-PCIE card Refer to the following to remove and replace the PCIE card. 1. 2. 3. 4. Turn off the EM-200. Disconnect the AC adapter cable. Overturn the EM200. Remove the two screws as shown in the right. 5. Open and remove the Mini-
PCIE card compartment cover. 27 28 C H A P T E R 3 U P G R A D I N G C O M P O N E N T S 6. Locate the Mini-PCIE card, as shown in the right. 7. 8. Remove the screw on the Mini-
PCIE card, Mini-PCIE will pop up 45 degree. When it pops up, gently remove it. To replace the Mini-PCIE card, reverse the above procedure. 29 30 C H A P T E R 3 U P G R A D I N G C O M P O N E N T S APPENDIX This appendix describes locating and solving problems that you may encounter while using the EM-200. Troubleshooting Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specic solutions. Tips for Troubleshooting In each problem-specic section, try the steps in the order suggested. This may help you to solve the problem more quickly. Try to pin point the problem and thus avoid replacing non-defective parts. For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step. Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel. Use some other electrical device to conrm that the electrical outlet is working. Ensure all connections are securely attached. General Problems Refer to the following general problems you may encounter. PROBLEM SOLUTION The display screen is dark. An incorrect date and time are displayed. Cannot be turned off after crash. Cannot be powered on Make sure that the EM-200 is not in suspend mode. Set the date and time in BIOS or Operation System. Long press the power button for 4 seconds to force shutdown. Connect the AC adapter, if it can be powered on, there is insufcient battery power. If it still unable to be powered on after charging, please have the EM-200 serviced. 31 32 A P P E N D I X Having the EM-200 Serviced If you are unable to solve the problem, you should have the terminal serviced. Pack the terminal in the original carton. (See Unpacking the EM-200 on page 1.) Include a description of the problem and a checklist of the steps you took when trying to x the problem. The information may be useful to the service personnel. Return the terminal to the place you purchased it. Specication Processor BIOS Chipset Memory LCD Display With Touch Panel Graphics Hard Disk Drive Bluetooth LAN & WiFi Interface I/O Port Speaker Input Devices Intel Atom 1.6GHz Processor (N270) 1024K BB Flash ROM Intel 945GSE Memory DDRII SO-DIMM X 1, 1GB, support up to 2GB 10.1 TFT-LCD, 1024x600, 200 nits, LED backlight Resistive touch Integrated in Intel 945GSE graphics controller One 2.5" 160GB SATA HDD Bluetooth 2.1 Ethernet 10/100 Base T IEEE 802.11b/g/n 5-in-1 Media Card Slot x 1 Mini-PCIe Slot x 2 (Internal) Express Card 34 Slot x 1 USB Port x 3 Audio Jack x 2 (Mic-in and Headphone out) VGA D-Sub x 1 DC-in x1 1 Watt x 2 Touch panel Internal Mic-in System Status LED Power on/Suspend, Battery Charging, HDD Access, RF, Caps Lock, Number Lock Buttons & Switch WebCam Battery Pack Battery life Dimensions (W x H x T) Weight Power on/off switch 1.3M Pixel CMOS webcam integrated (optional) DC 7.4v, 4,500mA Li-polymer battery up to 3 hrs (estimate) 189 x 268 x 25.7mm 1,250g 33 34 A P P E N D I X